PROVIDING AND INSTALLATION OF DECORATIVE POLEWITH LED FROM MUSSORIEDIVERSION DEHRADUN TO MUSSORIE UTTARAKHAND

Supply of Decorative 90W LED Street Light Mechanical & Constructional Specifications Housing -Aluminium pressure dia cast, Screw and Hardware - MS Zinc plated and passivated, Corrosion Resistant, Heat sink - Housing act as a heat sink & maintain LED junction temperature for optimum Led Life, Internal wiring – Teflon multistrangth wire, Front Casing - Ultra Violet stabilized Toughened Glass covered with die cast Aluminium frame, control gear - Internal- Electronic Driver, supplied with luminaire with complete wiring, LED Specification LED – Osram/ KER, LED Watt – 1 watt, LED rating current – 110mA, View angle – 120°, LED efficacy - >130, Color Temperature – 3000K – 6000K, Operation Temperature - -10 ° to +50 °, colour Rendering - >80, LED life - >50000 Hrs, Number of LED – 80, Electrical Specifications Rated Voltage (VAC) -240 VAC, Frequency (Hz) - 50± 2, Operating voltage – 90-320V, Imput Voltage – 90W, Output current – 1.46A, Output voltage – 54V, power factor - >0.95, THD(%) - <10%, Surge protection – up to 6 KV, Lumen – 9540 >Im>9720, Driver – Isolate CC type, Driver Location – Internal inside the housing, Driver efficiency - >88, Protection - Over Temperature, Short-circuit Protection, OC Protection, Reverse Polarity Protection, LED Warranty – 5 Yrs, arm clamp, nut bolt, wire, sensor, installation – as required. Step-Down Schedule For a standard 9-meter pole installation, a common power-saving profile looks like this: Time Period and Power : Sunset to 11:00 PM Peak Traffic : 100% 11:00 PM to 01:00 AM Transition : 70% 01:00 AM to 04:30 AM Low Traffic : 30% - 40% 04:30 AM to Sunrise Early Commute : 70% - 100% Warrenty of upto 5 years.

Supply of decorative ornamental pole with Single arm Decorative bracket.Total height of the pole with bracket shall be 9000 mm nominal above the ground. The pole shall be made out of mild steel tube in multiple sections with grooves as per attached drawing the different sections shall be joined together through flanges and swaging joints and are welded to get stable structure.The bottom section shall be of 165 mm dia x 3.6 mm thickness x 1200 mm long,the middle section shall be of 114 mm dia(grooved to dia108 mm and swaged)x 3.6mm thickness x 1800mm long and top section shall be 89mm dia(grooved to dia82 mm and swaged)x 3.6 mm thickness x 2800 mm long.The base plate shall be of dimension 300 x 300 mm and thickness 15 mm and joined with the pole by welding joint with the help of stiffeners.A built in service window shall be provided to accommodate a 6 amp SP MCB and 32 amp heavy duty connector for mains connections in the bottom part of the pole as shown in the attached drawing.The cast iron decorative embellishments shall be fixed with the pole with the help of SS grub screws as shown in attached drawing.The decorative bracket shall be made out of Mild steel tube,rod &embellishments shall be made of cast iron,total height of the bracket shall be 1200 mm till the bracket arm.The decorative pole and decorative bracket shall be machined and polished properly to give it a smooth surface.The decorative pole and decorative bracket shall be duly pretreated by shot blasting process and coated with high end epoxy primers and top coat in UV ray resistant polyurethane / Polyester coating in approved colourshade.The Coating on the pole and bracket shall bebaked in oven at required temperature and parameters.The DFT of coating on pole shall be 90 microns (minimum).The coating on pole and bracket shall pass minimum 500 salt spray hours.Wind pressure calculation shall be done as perIS875.The contractor has to specify pole manufacturers name and manufacturing facility details in technical bid.The pole manufacturer shall have in house facility for pole fabrication consisting of Laser cutting machine , pole grooving macine,Pole fabrication and Mig

Installation of 90W LED street Ligh Fitting in Pressure die cast aluminium housing with Heat resistant glass, IP66 Protection, 150lm/w/IK10 /15KV SPD/<10% THD inexisting bracket

Erection and Fixing of hot dipped galvanised M.S. Single Arm Over Hang (48.3 X 3.25 mm) with cap (400 x 88.9/114.3 x 3.25 mm) over the existing poles. arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification.

Erection and Fixing of decorative ornamental pole with Single arm Decorative bracket.Total height of the pole with bracket shall be 9000 mm nominal above the ground. The pole shall be made out of mild steel tube in multiple sections with grooves as per attached drawing the different sections shall be joined together through flanges and swaging joints and are welded to get stable structure.The bottom section shall be of 165 mm dia x 3.6 mm thickness x 1200 mm long,the middle section shall be of 114 mm dia(grooved to dia108 mm and swaged)x 3.6mm thickness x 1800mm long and top section shall be 89mm dia(grooved to dia82 mm and swaged)x 3.6 mm thickness x 2800 mm long.

Supply of 3Phase ,15KVA outdoor type CCMS Panel equipped with 1 No Street Light Controller, 1 no Energy meter,1 no TPN MCB, 3, Nos 3 Pole contactors, 3 Nos 1Pole MCB’s, Battery, SMPS, 3 Nos Current Transformers & Toggle switches. Rated Capacity: 15 KVA, Power Supply: Three-phase, Voltage: 220/240V Real-time Monitoring: Integrated with a Centralized Control and Monitoring System (CCMS) for remote operation. Durability: Robust construction with high-quality materials to withstand harsh environmental conditions. Energy Efficiency: Reduces energy wastage by automating street light operations based on demand and schedules. Including warrenty for 5 years.

Earthwork excavation in all types of soil/soft rock for pole foundation (0.6m×0.6m×1.5m). Providing and laying PCC (1:4:8) for base bedding (100mm thick). Providing and laying RCC (M20 grade) for foundation and plinth including shuttering. Supplying and fixing 4 Nos. J-type Foundation Bolts (24mm×600mm) with nuts/washers.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) including excavation and sand refilling the trench but excluding sand cusioning and protective covering

Supply and laying of 35Sq.mm, 3.5Core PVC Al armoured cable of 1.1KV grade ISI marked Cable