SPECIAL REPAIR INCLUDING ROOF TREATMENT OF BLD NO P-02 OF 206 FD WKSP COPY AT BINNAGURI MIL STN UNDER GE (S) BINNAGURI.

Amount

Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) and removal from site.

All as item No 1 here-in before but n.exc 1.5 Sqm each.

Dismantling floor, hearth wall tiling incld cement mortar bedding (but not backing) removing servicable tiles to store & rubbish off the premises complete all as specified.

Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc and removal of rubbish off the site complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for grils.rails etc

Demolition of brick work built in cement mortar including quions, arches, pillars etc but excluding ashlar facing and dressed stone work including removal of rubbish off the site complete all as directed

Demolition of cement concrete of any position and description.

Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 500m and n. exc. 900m incl roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed.

Demolition of reinforced cement concrete in any description and in any position (reinforcement cut as required to facilitate demolition).

Dismantling water tanks and removing to store of capacity exc 250 & n.exc 500 ltrs.

Disconnecting existing tanks of capacity exc 250 Ltrs and n. exc 500 Ltrs, setting aside (or lowering if required) for repairs with all necessary fitting as required , cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed.

Taking up or down 15mm bore steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc complete all as specified

All as per item no 12 above but 20 mm bore pipe.

M&L for glazed coloured ceramic tiles (450x350x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match over 15mm thick rendering in CM(1:4) all as specified and directed by Engr-in-charge.

M&L for Vitrified ceramic tiles 10mm th (square / rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl. 15mm th. screed bed in CM 1:6 of floor finishes complete all as specified.

All as per item No 15 as above but in skurting

All as per item No 17 as above but in skirting

M&L for non-skid ceramic coloured (400x400x7 to 8 mm thick) tiles set and jointed in neat cement slurry pointed in white or coloured cement to match in floor over 15mm thick screed bed in CM(1:6) all as specified and directed by Engr-in-charge

M&L stepping stone 15 mm thick of colour as approved as in riser/vertical surface of stair case set and jointed in neat cement slurry over and including 10 mm thick rendering/back coat in cement mortar 1:4 complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C2 as in plinth protection/footpath using 40mm graded stone aggregate finishing cement concrete surface even & smooth without using extra cement including bitumen filling in two panel etc complete all as specified and as directed.

M&L for 25 mm thick PCC (1:2:4) type B0 ( 12.5 mm graded stone aggregate) , finished concrete surfaces even and rough to receive floor finishes.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, Copping, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L PCC (1:2:4) type B1 (20mm graded aggregate) as in roof kerbs, slightly rounded or chamfered on edges, mixed with water proofing compound 200 ml per beg of cement or as per manufacturer instructions finished even and smooth on exposed concrete surface without using extra cement all complete as specified and as directed. (Note: Water proofing compound shall be measured and paid perarately under relevant item of schedule 'A').

Material and labour for precast reinforced cement concrete (nominal mix) Type A1 1:1.5:3 (20mm graded stone aggregate) as in chajja including necessary formwork complete all as specified. Note:- Reinforcement shall be measured and paid for separately.

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) LLDPE water storage tanks 500lit capacity (Cylinderical vertical with polythene foam insulation as intermediate layer), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet and over flow connection etc complete all as specified.

S&F 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60x1.25 mm

M&L for plain, framed, factory made panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats.

S&F second class hardwood, factory made glazed and skelton shutters 35 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) supplied and fitted to chowkats.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing on SI page No 156 of SSR Part-II completed.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on SI page No.160 of SSR Part-II completed.

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified and as directed.

S&F Steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs guard bars etc. Note: (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery (iii) Glazing, wire mesh & painting grill shall be measured & paid for separately.

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and smooth without using extra cement complete all as specified.

Material and labour rendering 20mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layers 10mm thick each layer and top layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: WPC shall be measured and paid for separately as 'Supply only'.

Supply only liquid water proofing compound.

M&L for 5mm thick in CM 1:3 in ceiling finishing the surfaces even and smooth without using extra cement.

M&L for two coat of acrylic distemper on new wall surface including preperation of the surface over 1.00mm thick (average thickness) all as per manufacturer's specification and as specified.

-----Blank-----

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new /old wall surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel painting to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth.

Material & labour for preparation of old painted surfaces of wood & wood based materials over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as directed by the Engr-in-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or girth

Material and labour for applying one coat of synthetic enamel paint on old painted steel and iron surfaces of any description over 10 cm in width or girth including necessary preparation of surfaces.

Complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc and applying two coats of acrylic distemper over a coat of primer over 1.00mm thick average thickness as required and complete all as specified.

Material and labour for preparation of old plastered ceiling surfaces by brooming down or steel wire brushing: scrapping down smoke soot, mould, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified.

M&L for applying three coat of white washing including preparation of new or previously untreated surface of ceiling.

M& L for form work to chajjas and similar items including edges ,rough finished surfaces of concrete flat.

M&L for mild steel TMT bars,10mm dia and over cut to length, bent to shape required including cranking ,bending spirally, hooping for columns, hookings/ends and binding with and including MS wire not less than 0.9 mm dia or securing with clips.

M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required, including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip.

M&L for MS flat iron bent to shape, holes drilled etc complete as in hold fast & wind ties etc including one coat of red oxide paint.

-----Blank-----

M&L for water proofing treatment to RCC roof slab as specified below and as directed by Engineer-in-Charge:- (a) 10mm th cement plaster in CM 1:3 with integral WPC to be laid over the RCC roof slab when the concrete is green. (b) Applying a unifirom coat of bitumen primer @ 0.70 kg/sqm over cement plaster. (c) 4mm thick plain texture and weighing not less than 4.00 kg/sqm atactic Polypropylene Polymer (APP) modified bitumen based prefabricated five layer water proofing membrane reainforced with non woven polyster matt black finished over compatible primer at 0.4 Ltr / Sqm of density at 25 degree centigrade 0.87 - 0.89 kg/ltr and viscosity 70-160 cps or cold sticker and torch application of membrane with overlap while torchin g shall be 150mm on length side and 10 mm on width side. after necessary preparation of surface complete as per manufacturers instruction. M/s fosroc chemicals "Proofex Torchseal 3PI/4PI/Antiroof Plain" or M/s STP Limited "Super Themolary APP PL/MT/Superior Shaliplus/industrual bitumen, ShaliTex Primer" or M/s Sika India Pvt Ltd "Sika WP Shield 103P/PM/ Sika WP Shield 104P/PM) or equivalent as approved by GE. (d) Apply two coats of bitumastic - Aluminium paint over the membrane.

M&L for cutting out cracks to 'V' section (shape) in existing roof slab terracing cleaning out and filling solidely with cement and sand mortar (1:1) complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) as in floors as levelling course for roof treatment.

S&F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples.or wooden beadings for doors complete all as specified and directed.

S&F of in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples.or wooden beadings for doors complete all as specified and directed.

M & L for 15mm bore steel tubing medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete for this following.

All as per item no 61 above but 20 mm bore pipe.

Refixing of reusable GI pipes of 15mm bore after necessary cleaning and renewal of GI fittings as required all as specified. Note: (i) GI tubing retrieved against relevant item shall be reused. (ii) New GI fittings required shall be supplied by the contractor and the quoted rate shall be deemed to be inclusive of the cost of the same.

Al as per item No 63 here-in-above but 20mm bore.

S&F in repairs of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, long flush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC

Supply and fixing in repair for vitreous China (white) wash down water closet pan (pedestal pattern) of size 935 x 425 x 780mm with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, PVC seat cover (white) with SS fittings and making all necessary connections complete as specified. Make: Hindware Cat No 20011 (Sleek) for water closet or equivalent.

S&F in repair PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as directed.

Supply and fix in repair CP Health Faucet of premium quality and make Jaquar or equivalent including two way bib cock and PVC telephonic flexible tube fixed to 15mm bore pipe.

S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified and directed.

Supply and fix in repair for vitreous China flat back urinals(white) of size 440mm x 315mm x 265mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including waste pipe, 15mm dia PVC connector pipe , CP urinal spreader complete all as specified. Make: Hindware Cat No 60001 or equivalent as in the list of makes.

Supply and fix in repair for vitreous China wash basin white, flat back, size 550 x 400 mm with CP brackets (02 Nos) including cutting for pinning in ends of brackets and making good disturbed surfaces with CM (1:4) complete all as specified. Make:-HINDWARE Cat No 10054 (Mini Regal) or equivalent as in the list of makes.

S&F of PVC connections 15 mm size with PTMT nuts of length 600 mm.

S&F in repair 15 mm bore two way bib cock CP with flage complete all as specified and direcrted.

S&F in repairs bib taps 15mm bore fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs for 15 mm bore stop cocks fancy type, chromium plated reduce body, long shank, cap (concealed type) screwed down high pressure screwed both ends for iron pipe or for union etc as in repair.

S&F in repairs angle valve, fancy type chromium plated, brass, 15mm bore complete all as specified and directed.

S&F in repair Brass CP mixer for mixing hot & cold water screweddown for iron pipeand fixed complete all as specified and directed.

S&F in repair central hole basin mixer for WHB complete all as specified Make: Prayag model Matrix 6550 or equivalent as in the list of makes.

S &F in repair stainless steel curtain rods 25 mm dia 0.50mm thick, anodised aluminium alloy with fixing brackets, stops,and complete fitments all as specified and directed.

Supply and fix PVC (SWR) pipes 110mm dia,type 'A' conforming to IS, single socketed, in any length with rubber ring joints laid in trenches or floor complete all as specified.

S&F for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed by Engr-in-Charge (Bore of pipe 110mm)

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with acess door.

S&F 110mm dia PVC SWR vent cowl

M&L in repairs for CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 75 mm) as in repair

M&L for CI floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 75 mm) as in repair

M&L for 150 mm size aluminium anodised cast type handles.

S&F of 200mm long aluminium anodised,barrel tower bolt of extruded section.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S&F 100mm size mild steel butt hinges medium weight.

M&L for pre polished coloured chequered cement concrete tiles made with grey cement and pig-ments of size 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over in pavement / footpath / floors over incl 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor,conforming to IS-694 of size 1.50 sqmm nominal cross sectional area single core drawn in and includingPVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings, including, pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories, One light point controlled by one way switch 5/6 amps. complete all as specified.

ALL as per item no. 94 but One ceiling fan / exhaust fan point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item no 94 but One socket out let 5/6 amps point on the same board complete all as specified.

ALL as per item no. 94 but One socket out let 5/6 amps point on the independent board complete all as specified.

All as per item No 94 above but wiring with 4.0 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash typecomplete all as specified. by Engr-in-Charge.

S&F Switch socket combination 3 pin 16A, multi pin, flush type

S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified.

S & F lamp holder, isolated body, with back plate suitable for batten/angle fittings complete all as specified.

S & F deluxe fan electronic regulator 230 volts AC 50 Hzs rotary step white/ivory finish complete all as specified.

S&F, IP 20, class I, LED tube light fittings 18 W (or nearest next higher wattage) (4feet), wall/ surface mouted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminiare efficiency > 95 lumens/ watt, power factor > 0.90, operating range- 140 to 270V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

S & F LED street light fittings 35 watt in aluminium PDC housing, toughned glass cover with IP66 protection complete all as spedified.

S&F sheet metal enclosure for vertical type TPN DB 4 way, double door incl hinged shutter and locking arrangement for fixing for fixing DBs, flushed/ semi flushed/ grounting on wall as per site requirement including DIN rail channel to mount MCBs with TPN bUs bar channel of rating 200 Amps and neytral link duly mounted on F class insulator with colour coded heat shrinkable sleeves and powder coated paint after preparation of surfaces panel, including four pole MCCB 125 Amps (or higher) with blanking plates including provision of blanking plates as required and taking down the old one complete all as specified and directed by Engr-in-Charge.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with din rail, IP-20 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified.

M&L for street light bracket made out of GI pipe light grade 32 MM dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer.

Taking down ceiling fan/exhaust fan sealing cable end, dismantling blades and removing fan and blades to store and refixing the same after necessary repair works complete all as specified.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed

M&L Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete including necessary taking down all as specified and as directed.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring complete all as specified. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation of poles/stays/cables etc and getting out in any type of soil.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers n.exc 25cm.

Removing excavated material n.exc 50m and depositing were directed at a level n.exc. 1.5m above the starting level.

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compactioncomplete all as specified. by Engr-in-Charge. (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I)

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete including necessary taking down all as specified and directed

Supply and fixing 40 mm dia GI tubing medium grade ISI marked laid in trenches / laid under floor for protection of cable including all fittings such as elbow, bends, etc and short length complete all as specified.

M/S MAJUMDER CONSTRUCTION (BID ID -3270948)

SHRI ARABINDA GHOSH (BID ID -3270960)

M/S NIKITA ENGINEERING CO (BID ID -3270913)

M/S ALOKE CHAKRABORTY and CO (BID ID -3270927)

M/S MOHAN KUMAR BANSAL (BID ID -3270938)

MESSRS SEN BROTHERS (BID ID -3271002)

N K Construction (BID ID -3270974)