SCSP Grant

Conducting Geo-Physical Survey by the Geologist and submission of feasbility report of yield for Drilling of Borewell.

Drilling of Bore well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time 0 to 90 mtrs 90 to150 mtrs etc., complete and as directed by the Engineer- in -Charge of the work

above 90 up to 150 mtrs

Supply, delivery, and insertion of 180mm dia OD PVC 10 Kg/cm2 casing pipe including cost and conveyance of all materials and labour charges etc., complete and as directed by the Engineer- in -Charge of the work including all taxes but excluding GST

Supply of 6 Sqmm WPSC (Weather Proof Single Core) ISI Alluminium Wire. Makes : As per list of recommended brands. (ELEC 1.6.1)

S&F 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including the cost of pipe & its fittings & labour charges complete.

S&F 50 mm Nominal Bore Long Couplings Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including the cost of pipe & its fittings & labour charges complete.

Supply and Transportation of 12.5 H.P 10Stage 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V ± 10%, Three Phase 50 Hz AC supply etc complete for 6" Bore well. Makes: As per list of recommended brands as category I.

Fabrication ,transportationand and supply of wall mounted Control Panel Board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V 96x96mm size. Including Voltmeter ; 0-500 V 96x 96 mm size, 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size)-1No. Single phase preventor of suitable range - 1No. 32 A TP, 10KA MCB. - 1No Indication lamps (R-Y-B) with switch control - 1se Voltmeter & Ammeter selector switch - 2 Nos, Supply and fixing of ISI Mark suitable capacitor Makes: L&T/C&S / SALZAR/HPL/AEI/Meco/Rishab-1No. 0 to 20 Amps/0 50 Amps Ammeter (96x96mm size). Makes: L&T/ C&S/SALZAR/HPL/AEI/Meco/Rishab-1No. Single phase preventor of suitable range Makes: L&T / Minilec/Powertec.-1No.32A TP, 10KA MCB. Makes: Legrand/Schneider/- 1No. Indication lamps (R-Y-B) with switch control - 1set. Voltmeter & Ammeter selector switch - 2 Nos. Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells.

Supply of 3 Core 4.00Sqmm ISI marked Flat Copper cable of ISI for Submersible Motors confirming to IS: 694:1990.Makes: As per list of recommended brands as category I

Supply & Delivery of bore well material including cost and conveyance of all material, labour charges etc., complete.

50mm X 12" Nipple

2 X 2 1/2 Non Return Value

2 X 2 1/2 Plange

50mm X 5 Feet Nippal

110mm PVC TEE 6KG/Sqmm

110mm PVC Coupling 6KG/Sqmm

1/2 X 2" Nut & Bolts

5/8 X 3" Nut & Bolts

Planger Watchers

Supply, Delivery of D.I double flanged Sluice Valves conforming to IS- 14846 (with up to date amendments, if any) including gear arrangements for the following dia. as per test pressure having Body, Bonnet, Dome, Stool cover, Wedge, Stuffing box, Gland, Thrust plate, Cap/Hand wheel with D.I; Stem, Body seat ring, Wedge facing ring, Bushes, Bolts, Nuts, Pinion and Pinion shaft with Stainless steel (IS 6603) ; Wedge nut, Shoe, Channel with Leaded Tin Bronze ( IS 318 ); Gasket with Neoprene Rubber; Gland packing with Rubber; Gear, Gear housing with Cast Steel excluding all taxes and transportation, etc. complete ISI marked. for 100mm DI Value

Manufacture, Supply and Delivery of Cast Iron Pipes and Fittings (spls.) Conforming to IS. No.7181/1986, 5531/1988, 3950/1979 and C.I.D Joints confirming to is No. 8794 /1988 at site of work anywhere in A.P. Including, loading, unloading, transportation to site of work stacking at site transit risk and package, excluding taxes and duties.

100mm Tail Piece

100mm CID Joint

Assistant Engineer

Nandikotkur Municipality

Conducting Geo-Physical Survey by the Geologist and submission of feasbility report of yield for Drilling of Borewell.

Drilling of Bore well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time 0 to 90 mtrs 90 to150 mtrs etc., complete and as directed by the Engineer- in -Charge of the work

above 90 up to 150 mtrs

Supply, delivery, and insertion of 180mm dia OD PVC 10 Kg/cm2 casing pipe including cost and conveyance of all materials and labour charges etc., complete and as directed by the Engineer- in -Charge of the work including all taxes but excluding GST

Supply of 6 Sqmm WPSC (Weather Proof Single Core) ISI Alluminium Wire. Makes : As per list of recommended brands. (ELEC 1.6.1)

S&F 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including the cost of pipe & its fittings & labour charges complete.

S&F 50 mm Nominal Bore Long Couplings Medium Grade properties & weight as per IS 1239 ISI mark with GI fittings including the cost of pipe & its fittings & labour charges complete.

Supply and Transportation of 12.5 H.P 10Stage 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V ± 10%, Three Phase 50 Hz AC supply etc complete for 6" Bore well. Makes: As per list of recommended brands as category I.

Fabrication ,transportationand and supply of wall mounted Control Panel Board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V 96x96mm size. Including Voltmeter ; 0-500 V 96x 96 mm size, 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size)-1No. Single phase preventor of suitable range - 1No. 32 A TP, 10KA MCB. - 1No Indication lamps (R-Y-B) with switch control - 1se Voltmeter & Ammeter selector switch - 2 Nos, Supply and fixing of ISI Mark suitable capacitor Makes: L&T/C&S / SALZAR/HPL/AEI/Meco/Rishab-1No. 0 to 20 Amps/0 50 Amps Ammeter (96x96mm size). Makes: L&T/ C&S/SALZAR/HPL/AEI/Meco/Rishab-1No. Single phase preventor of suitable range Makes: L&T / Minilec/Powertec.-1No.32A TP, 10KA MCB. Makes: Legrand/Schneider/- 1No. Indication lamps (R-Y-B) with switch control - 1set. Voltmeter & Ammeter selector switch - 2 Nos. Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells.

Supply of 3 Core 4.00Sqmm ISI marked Flat Copper cable of ISI for Submersible Motors confirming to IS: 694:1990.Makes: As per list of recommended brands as category I

Supply & Delivery of bore well material including cost and conveyance of all material, labour charges etc., complete.

50mm X 12" Nipple

2 X 2 1/2 Non Return Value

2 X 2 1/2 Plange

50mm X 5 Feet Nippal

110mm PVC TEE 6KG/Sqmm

110mm PVC Coupling 6KG/Sqmm

1/2 X 2" Nut & Bolts

5/8 X 3" Nut & Bolts

Planger Watchers

Supply, Delivery of D.I double flanged Sluice Valves conforming to IS- 14846 (with up to date amendments, if any) including gear arrangements for the following dia. as per test pressure having Body, Bonnet, Dome, Stool cover, Wedge, Stuffing box, Gland, Thrust plate, Cap/Hand wheel with D.I; Stem, Body seat ring, Wedge facing ring, Bushes, Bolts, Nuts, Pinion and Pinion shaft with Stainless steel (IS 6603) ; Wedge nut, Shoe, Channel with Leaded Tin Bronze ( IS 318 ); Gasket with Neoprene Rubber; Gland packing with Rubber; Gear, Gear housing with Cast Steel excluding all taxes and transportation, etc. complete ISI marked. for 100mm DI Value

Manufacture, Supply and Delivery of Cast Iron Pipes and Fittings (spls.) Conforming to IS. No.7181/1986, 5531/1988, 3950/1979 and C.I.D Joints confirming to is No. 8794 /1988 at site of work anywhere in A.P. Including, loading, unloading, transportation to site of work stacking at site transit risk and package, excluding taxes and duties.

100mm Tail Piece

100mm CID Joint