PROVISION OF SECURITY WALL CONCERTINA COIL AT SURVEY NO 141, 154 AT TECHNICAL AND SPECIAL REPAIR TO CHOPRA HALL- A HISTORIC MULTIPURPOSE CONFERENCE HALL AND REPAIR TO FENCING AND RETAINING WALL AT CIRCULAR ROAD ITM MUSSOORIE UNDER GE (I) RND DEHRADUN

Amount

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete as specified and directed.

M&L for S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete incl Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws complete incl Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29 mm X 24 mm X 0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 3/4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture including Dismantling of wall and ceiling boards any thickness including cover filletscomplete all as specified and directed.complete all as directed. Make :- EVEREST or other equivalent as approved.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

S&F 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, coping, benching, kneelers, apex stone, bed plates, kerbs, etc. including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as directed.

M&L Complete removing of existing treatment from wall / ceilling by using machinary complete all as specified and directed.

M&L for Prepration of scrapped surface of wall / ceilling and applying 2mm thick Asian acrylic damp proof wall care putty in two coats as per manufactur instruction complete all as specified and directed.

M&L for Preparation of puttyied / new plaster surfaces of wall/ceiling and applying one coat of alkali resistant primer complete all as specified and directed.

M&L for Prepration of primed surfaces of wall / ceiling and applying two coats of oil emulsion distemper complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in 1:6 cement mortar.

Excavating in trenches n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in any type soil complete all as specified and directed.

M&L for PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed.

M&L for RCC 1:1 ½:3 type A 1 using 20mm graded crushed stone aggregate as in foundations, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slab, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for RCC 1:1 ½:3 type A 1 using 20mm graded crushed stone aggregate as in beams, cantilever bressummers lintel over 1.5 m span etc complete all as specified and directed.

M&L for RCC 1:1 ½:3 type A 1 using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

Use & waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter including fair finished surfaces complete all as specified and directed.

Use and waste of formwork to sides of concrete pillar, columns, posts strutts complete all as specified and directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports etc. and similar work of fair finished flat surface of concrete complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and directed.

M&L for Preparation of new plastered surfaces of wall / ceiling and applying two coats of cement base paint complete all as specified and directed.

S&F Mild Steel work as in posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wires etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting and riveting etc including dismantling existing posts and struts complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works conforming to Fe-290 Gd E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed..

Returning filling in trenches including spreading, leveling, watering and well raming in layers not exceeding 25 cm complete all as specified and directed.complete all as specified.

Removing exc materials exc 500 mtr but up to total distance nexc 1.5 km & depositing where directed at level n. exc. 1.5m above the starting point complete all as specified and directed..

M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling exising barbed wire of any description as in fencing complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for galavanised 2 stand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and strainings and fixing to any type of standard rails straining bolts ,including securing or tying at crossing with and provision of galvanised mid steel wire, staples or steel pins, etc. including restraining & resecuring & including making good staples etc ( each line to be measured )

S&F concertina coil 2.5 mm dia of core wire in 610 mm circular dia of each coil having a core wire of high carbon spring steel of high tensile strength as per grade of IS-1454(Part-I) with low carbon steel strip punched tape of 19 mm wide, 0.50 mm thick and series of knife edge sharp barb/blades @ 25 mm centre to centre punched all along the length of both sides of strip at regular interval conforming to IS-513 complete all as specified and directed. Note:- Concertina coil having 50 Rounds per 6 RM.

S&F 110 mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls fixed on wall or floor including all fittings complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

M&L for Walling of random, rubble, stone masonary brought upto courses, well bonded bedded and soilidly hearted and built in cement mortar (1:6) in foundation up to ground level complete all as specified and directed. Note: The bond stone as used random, rubble, stone masonary shall be measured and paid separately under respective item of BOQ.

M&L for Walling of random, rubble, stone masonary brought upto courses, well bonded bedded and soilidly hearted and built in cement mortar (1:6) in super stracture avobe ground level complete all as specified and directed. Note: The bond stone as used random, rubble, stone masonary shall be measured and paid separately under respective item of BOQ.

M&L for Extra over stone walling for hammer dressing to face stone with maximum depression on face from straight edge held against the dressed surface not exc 40mm and dressing of face and joints as specified of random rubble walling uncoursed or brought upto coursed or lime or sand stone complete all as specfied and directed.

M&L for flush pointing to random or polygonal rubble masonry, uncoursed or brought upto courses in CM 1:3 complete all as specfied and directed.

S&F in repair 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls fixed on wall or floor including all fittings complete all as specified and directed.

M&L providing PCC 1:3:6 type-C 1 (using 20mm graded crused stone aggregates) as in bond stons for stone walling of any section and set in cement mortar 1:6 including use and waste of form work complete all as specified & directed.

Dismanting posts or struts (wood, steel or R.C.C) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling expanded metal or IRC fabrics, any type complete all as specified and directed.

M & L for excavating hard/dense soil in post holes (or similar holes) each n exc 0.5 cum , getting out , returning , filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering , and removing surplus soil to a distance n exc 50 m and making good surfaces.

Mild Steel screw bolts 5 to 10 mm dia (machine made ) with hexagonal or squre head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or squre nuts exc 5 cm but n exc 10 cm long complete all as specified and directed.

S&F Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply and fixing PVC coated galvanised chain link fencing, of size 4mm dia and mesh size 50 x 50 mm to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Taking down of carefully unserviceable Aluminium/copper point wiring (light, fan socket or power) complete with fitting such as switches, ceiling rose lamp holder, sockets, fan regulators, SK/FTL light fittings etc removing materials for store for keeping in safe custody or for taking credit (credit for above items should be taken as per conditions separately) and making good disturbed surfaces of walls, floors etc as per existing finishes complete all as specified and directed.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles GI screws, rawal plugs in ceiling or roof if not possible including Tee, Junction boxes and provision of flush metal boxes, inner and outer plate suitable for modular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan point controlled by one Switch. Make of cable: Gloster/Polycab/L&T, Make of conduit: Finolex/Polycab/Supreme

All as per Srl item No 53 here in before but point wiring for 5 pin switch socket outlet, 5/6 Amps on same board with other switches complete all as specified and directed.

All as per Srl item No 53 here in before but for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board complete all as specified and directed.

All as per item No 53 here in before for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete all as specified and directed.

S&F Modular switch single pole one way 6 amp complete all as specified and directed. Make - Legrand(Wood)/ Anchor(PENTA)/ Crabtree(Havells)

S&F Modular switch single pole one way 16 amp complete all as specified and directed. Make - Legrand(Wood)/ Anchor(PENTA)/ Crabtree(Havells)

S&F Modular switch , 6 amp, single pole, two way complete all as specified and directed. Make - Legrand(Wood)/ Anchor(PENTA)/ Crabtree(Havells)

S&F Modular socket outlet 2/3 pin combined 2 module 6/16 amp complete all as specified and directed. Make - Legrand(Wood)/ Anchor(PENTA)/ Crabtree(Havells)

S&F exhaust fans made of steel body AC single phase 240V copper wounded of size 300 mm sweep with louver shutter complete complete all as specified and directed. Make: Havells/CG/Bajaj.

Supplying, fixing & testing in replacement UNSV recess mounting in built 36 Watts,2'x2' LED ceiling light fitting with slim line extruded aluminium/ CRCA body, opal acrylic diffuser, electronic driver etc and all accessories pre wired including connecting to source complete all as specified & directed. Make- Crompton/Phillips/Havells.

S&F in replacement of UNSV Compact commercial batten with universal batten fitting suitable for single T8 LED tube and lamps complete all as specified and directed. Make:C&G or euivalent in Philips/ Havells/CG

S&F in replacement of UNSV fluorescent tubeT8 LED lamps for single universal batten fiting complete all as specified and directed. Make:C&G or euivalent in Philips/ Havells/CG

S&F Angle holder, insulated polycabonate body with back plate suitable for batten fittings suitable for one number LED lamp complete all as specified and directed. Make of holder - Havells/Philips/ C&S

TRILOK SINGH KHAROLA

Ram Naresh Singh Sikarwar

SARASWATI CONSTRUCTION CO