Laying of UPVC underground pipeline for outlet RD 40500/R Kakrala Minor excluding supply of pipe.

Amount

Excavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, including the cost of crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres.

First class brick masonary 229 mm thick laid in cement sand mortar 1.6 in foundation and plinth including supply recarriage of bricks cement .

10mm thick cement plaster 1.4 on sides walls (-) Rs.1.25/- for scaffolding.

10mm thick cement plaster 1:4 on bed and top.

Reinforced cement concrete 1:2:4 hand mixed but including steel reinforcement

Cement Conc.1:2:4 including supply, carriage & with stone ballast or shingle

Cement concrete 1:4:8 with brick ballast 40mm gauge

Lowering, jointing and cutting of UPVC pipe laying same to correct gradient and alignment and jointing ends and fixing collars with cement mortar 1:2 as per IS 458:2003 in all depths complete in all respect. (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Supplying, lowering of MS Pipe as per IS:4270-2001 including MS sockets having dimensions as per IS code duly welded with MS electrode to have extra strength to lower the pipe into tubewell bore. (a) 100mm

Wrought Iron and mild steel ladders, framed grills, grating etc. complete fixed in position in D-tank.

Providing orange colour safety footrest of minimum 6mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar confirming to IS: 1786 having minimun cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm

Providing and fixing of Alfa Valve fitted on riser pipe to act as Nakka (D regulators) (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Centreing &shuttering for Concerte faces

Providing & Fixing of Steel Shutter Gate Assembly in Main Pipeline complete in all respect

Dismantling of Flexible Pavements (By Mechanical Means) Dismantling of flexible pavements thickness above 50mm by mechanical means and disposal of dismantled materials up to a lead of 1000 meters, stacking serviceable and unserviceable materials separately as per technical clause 202 of MORT&H specifications

Water Bound Macadam Grading II (without screening for low volume Roads/undersigned Roads). Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications

Tack Coat @ 1.00 Kg per sqm ( for WBM patches where surface dressing not applied), Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 1.00 kg per sqm on the prepared granular surface after cleaning the surface complete as per technical specifications

Open-Graded Premix Surfacing 20mm thickness. Providing, laying and compaction of open - graded premix surfacing of 20 mm thickness consisting of crushed stone aggregates of specified grading premixed in a Continuous type hot mix plant with bituminous binder VG-30 @ 1.46kg per sqm, laid with Paver Finisher Mechanical and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications.

Seal Coat Type B.Providing and laying of premix sand seal coat premixed in Continuous type hot mix plant using specified fine aggregates and penetration grade bitumen VG-30 @ 0.68kg per sqm, laid to the specified levels, grade and cross fall complete as per technical clause 511 of MORT&H specifications

Providing and fixing Elbow/bends of 90 degree 6kg/cm2 pressure as per IS 4985 i/c testing commisioning and complete in all respect to the specification of engineer in charge. . (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Providing and fixing Elbow/bends of 45 degree 6kg/cm2 pressure as per IS 4985 i/c testing commisioning and complete in all respect to the specification of engineer in charge. . (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Providing and fixing equal Tee of 6kg/cm2 pressure as per IS 4985 i/c testing commisioning and complete in all respect to the specification of engineer in charge. .(a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Providing and fixing MS service saddle as per IS 4985 i/c testing commisioning and complete in all respect to the specification of engineer in charge. (a) 315 x 50 mm

Providing and fixing Tail end piece of 6 kg/cm2 pressure as per IS 4985 i/c testing commisioning complete in all respect to the satisfaction of engineer in charge. . (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Reinforced cement concrete M-15 grade 200 meter stone of standard design as per IRC 26-1967 fixing in position including painting and printing etc. complete as per technical clause 804 of MORT&H specifications

Reinforced cement concrete M-15 grade boundary pillar of standard design as per IRC 26-1967 fixing in position including painting and printing etc. complete as per technical clause 806 of MORT&H specifications

Advance Direction sign board 1200x1800mm rectangular as per IRC 67- 2012 with high intensity Microprismatic grade retro reflective Sheeting as per ASTM D 4956 – 09 and as per IRC 67 – 2012.

Supply and installation of antitheft mechanism for alfa valve of size. (a) 315 mm dia

(b) 280 mm dia

(c)250 mm dia

Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves (250mm) ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in-charge). B) Class PN-1.6 as per ISI

Providing & fixing double air valve ISI Marked as per IS-14845 including jointing all carriages complete .C.I Double air valve (Size 100mm)

Providing and fixing Reducer (for sluice valve) of 6 kg/cm2 pressure as per IS 4985 i/c testing commisioning complete in all respect to the satisfaction of engineer in charge. . (a) 315 x 250 mm dia

(b) 280 x 250 mm dia

(Loading & Unloading ) pvc pipes

(Carriage)PVC/HDPE pipes all sizes (Truck load 2.20 tonnes) upto 72 km

R R Concrette products (BID ID -689477)