Provision of ladies toilets near DSOI, Guard Rest Room near PJ Gate of RIMC, Electric connection to high mast light and drain of 21 Bihar under GE Dehradun

Amount

Surface excavation in soft/loose soil n.exc (not exceeding) 30cm deep and averaging 15cm deep and get ting out complete all as specified and directed.

Excavating in trenches in soft/loose soil, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out complete all as specified and directed.

Returning filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for Treating the bottom and sides of excavation with anti termite emulsion at the rate of 5 litres of emulsion per square metre of surface area complete all as specified

M&L for Treating the backfill in contact with foundation with anti termite emulsion at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as spcified

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified

M&L for Treating the soil under plinth protection with anti termite emulsion at the rate of 5 litres of emulsion per square metre of surface area complete all as specified

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified

M&L for Cement concrete in (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass-concrete complete all as specified and directed

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 complete all as specified

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for finished surface complete all as specified

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for finished surface complete all as specified

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for finished surface complete all as specified

M&L for cement concrete in Type A-1 (1:1.5:3) (using 20mm graded crushed stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified

M&L for cement concrete in Type A-1 (1:1.5:3) (using 20mm graded crushed stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified

M&L for cement concrete in Type A-1 (1:1.5:3) (using 20mm graded crushed stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified

M & L for RCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in chajja etc complete all as specified and directed.

M & L for RCC(1:1.5:3) type A-1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and strut etc,complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to chajja etc in rough finished flat surface of concrete complete all as specified and directed.

Material and labour for TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending for hooping and binding with and including mild steel wire not less than (0.9 mm) dia all as specified.

All as per Srl item No 23.00 here in above but 8mm dia complete all as specified.

All as per Srl item No 23.00 here in above but 8mm dia and over upto and including 10mm dia in stirrups spacers and binders all as specified.

M &L 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work and finished even and smooth without using extra cement complete all as specified and directed.

M &L 15 mm thick rendering in cement mortar (1:4) on fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed.

M&L for Hardcore of brocken stone of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified

M&L for 100 mm thick cement concrete in (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified

M&L for 25 mm thick cement concrete in (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in sub base of floor complete all as specified

M&L for coloured non skid tiles 10 mm thick(square/ rectagular) area of each tile exceeding 0.18 sq m but not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed

M&L for coloured Glazed ceramic (Digitel) tiles 300 x 600 x 7 to 8 mm thick as on skiting/ dedo etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plaster in cement mortar 1:4 complete all as specified and directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Supply and fixing 15mm bore med grade galvanized steel tubes with all fittings and fixed to wall and celing or laid in floors etc complete. (Make : Tata/ Bansal/ Ravindra)

All as per item No 34.00 here inabove but 20mm dia. (Make : Tata/ Bansal/ Ravindra)

S&F vitreous china wash down water closet pan rimless wall hung WC with PP soft close seat cover hinges accessories set size 370x510x360 mm fixed to wall and connected complete all as specified and directed. Make: Jaquar CNS-WHT 963SPP or equivalent in Parryware or Hindware.

S&F 100mm dia centrufugally cast iron spun pipe in any length with or with ears, with cement joints laid in trenches or in floors complete all as specified and directed.

All as per item No 37.00 here in above but fixed to walls.

S&F 75mm dia centrifugally cast iron spun pipe in any length with or with ears, with cement joints laid in floors complete all as specified and directed.

All as per item No 39.00 here in above but fixed to walls.

S&F 75mm dia centrifugally Cast iron spun fioor trap with grating including jointing to waste pipe fixed in cement concrete type B 1(1:2:4) complete all as specified and directed

S&F for vitreous china Wash Basin counter Top 600x400x185mm including stainless steel bottle trap and 40 mm dia GI pipe up to Floor trap complete all as specified and directed Make : Cat Part No SLS-WHT-6601 of Jaquar or equivalent of Parryware/ Hindware.

S&F 15mm bore brass chromium plated long body bath tub spout with CP brass cup and screwed down to GI pipe complete all as specified and directed Make Jaguar Cat part No SPJ-CHR-85429 or equivalent of Parryware/ Hindware .

S&F 15mm bore chromium plated brass connection 450mm long with 2 Nos connector incl PVC washer complete Make Jaquar Code ALD-803B or equivalent of Hindware / Parryware.

S&F 15mm bore chromium plated fancy type centre hole Single Lever Tall Boy with 140mm Extension Body Fixed Spout without Popup Waste System with 600mm Long Braided Hoses W.H.B mixer high pressure screwed to GI pipe complete all as specified and directed. Make : Jaquar ( cat part No :DRC-CHR-37005B) or equivalent of Hindware/ Parryware.

S&F 15mm bore brass chromium plated angle cock fancy tape with CP brass cup and screwed down to GI pipe complete all as specified and directed. Make:Jaquar (Florentine Series) Code No FLR5053N or equivalent of Hindware/ Parryware.

S&F for Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed. Make :Jaquar (Cat Part No: AHS-CHR-1581H) or equivalent of Hindware/ Parryware.

S&F chromium plated toilet paper holder fixed on wall with PVC Rawal plug complete all as directed. Make: Jaquar code no-ACN-CHR-1151N or equivalent of Hindware/ Parryware.

S&F 5mm thick looking mirror exc 1.0 Sqm but nexc 2.0 sqm fixed to wall withstainless steel nuts and including GI channel for holding morror from bottom fixed with rawl plug complete all as specified and directed

S&F C.P health flow set with P.V.C chord and C.P conector complete all as specified and directed. Make Jaquar Code No- ALD-CHR-583 or equivalent of Hindware.

S&Fstainless steel anticockroach grating jali 150x150 mm side intake fixed complete all as spcified

S&F stainless steel 304 grade railing fabricated as per design approved by GE complete all as specified and directed

S&F Towel Ring Round With Round Flange complete all as specified and directed Make Jaguar (Cat Part No:ACN-CHR-1121BN) or equivalent of Hindware/ Parryware.

M&L for preparation of newly plastered surface of wall and applying two coat of exterior emulsion paint over a coat of primer complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coat of plastic emulsion paint over a coat of primer complete all as specified

M&L for preparing new plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for preparing new plastered surfaces of wall with wall care putty and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M & L for 10 mm thick rendering in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and fair complete all as specified and directed.

M&L for preparing surfaces plastered or un-plastered new surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for 18-20mm Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and bull nosing to the exposed edges complete all as specified

M&L for 15-18mm artificial granite (of any colour) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and bull nosing to the exposed edges complete all as specified

S&F factory made PVC flush type shutter of 18mm thickness consisting of panel of PVC profile of 18mm (+ 0.7mm) thick celluka ply of denisity 600kg per cum manufactured by ISO-9000 certified company using for shutter celluka ply 18mm thick and fixed frame. The thickness of shutter edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.

S&F toilet partition made out of extruded aluminium alloy 60mmx60mm channel, rail, brackets with exposed face anodic coating, 18 mm compact laminate pannels with black core, edge polished finish , silver anodised aluminum edge trim to perimetre of all panel,including provn of door, dual 200 mm bullet style stainless steel pedestals with top and bottom screw, including 03 Nos of stainless steel hinges per door, die cast finish, including stainless steel finish indicator bolt and keeper (Turn bolt and indicator) including stainless steel coat hook with integrated door stop complete all as specified and drected by Engr in charge

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified

S&F 4 mm thick Figured glass, pin head type fixed in aluminiume frame in squares exc 0.5 sq. m in each pane complete all as specified

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified

S&F 8 mm thick interlocking PVC hollow false ceiling fixed with self tapping screw and including mild steel square tube of size 25mmx 25mm grid of size 600mm x 600mm of approved colour and design complete all as specified as per manufacturerer instruction and directed by Engr-in-Charge Make:- Placopan,Sintex

S&F pre-painted galvalume aluminium Zinc coating GI based corrugated steel sheet in manglore tile profile 0.50mm thick of an approved colour having tensile strenth of 550 Mpa as in roof covering, fixed with self tapping screws as specified

S&F Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W(Gde E-250) quality complete all as specified and directed.

M&L for two coats synthetic enamel paint on steel surfaces over a coat of red oxide primer of any description including preparation of new surfaces exc. 10 cms in width or girth all as specified

Demolition of brick work masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L 40mm thick PCC (1:2:4) type B-1 using 20mm graded aggregate as in flooring, finished even and smooth using extra cement, The floor shall be laid in alternate bays nexc 4sqm, and divided in to glass dividing strip, complete all as specified.(Glass dividing strip shall be measured and paid separately). .

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified

M&L for Preparation of new wooden or wood based surface of any description no otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-charge.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified

All as per item No 75.00 here in above but without glazing bars.

Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

S&F Galvanized mild steel wire cloth 0.56 mm nominal dia of wire & average width of aperture 1.18 mm fixed with tinned tacks of galvanized wire staples complete all as specified and as directed

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection, finishing the surface even & fair without using extra cement the plinth protection shall be laid in alternate bays n exe 2 Sqm, 10mm joints shall be provided, joints shall be filled with bitumen mastic, bitumen mastic comprise of 1 Part of Hot bitumen 85/25 grade and 3 parts of sand all by weight complete all as specified & directed including demolition of concrete complete all as specified and directed.

M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger ) (b) Providing PCC (1:2:4) type B-0, 25mm thick screed bed or bedding layer over roof surface .

Item No 80.00 contd. (c) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface. (d) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system..

M & L for 2nd class hard wood (SAL) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and fix flush shutters 35 mm thick with decoative face veneer with lipping/frame to match, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M & L 35 mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(a) complete all as specified and directed.

S & F factory made steel ventilator with top hung shutters including hinges with steel handles, steel peg stay, complete.

S & F Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles) with 2,4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face, supplying & fixing in the frame at site as per specification complete all as specified and as directed by Engr-in-Charge.

S&F Mild steel work as in small article as hold fast and similar small article, mild steel confirming to Fe-290 Gde E-165 including necessary welding or fixing with nuts & bolts as required complete.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 200 mm long,aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete

S&F 150mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc complete of approved quality.

S & F floor door stopper 150 mm size of brass body and tongue with hard drawn steel spring complete all as specified.

S&F non-skid ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in neat cement slurry and pointed in white or coloured cement to match the existing surfaces including 15mm thick screed bed or bedding layer in CM 1:6 for fixing tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles in vertical surfaces as skriting of 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

S&F non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in neat cement slurry and pointed in white or coloured cement to match the existing surfaces including 15mm thick screed bed or bedding layer in CM 1:6 for fixing tiles complete all as specified and directed.

M & L for glazed ceramic coloured tiles 350x 250x7 mm/ 450x350x7 mm thick as in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles incl 15 mm thick rendering in CM 1:4 for recieve tiles complete all as specified and directed.

S & F for Vitreous China squatting pan (Orissa pattern) size 580mm X 440mm, white with integral foot rests, any pattern including provision of cement concrete bedding (excluding flushing cistern and flush pipe) fixed,complete all as specified and directed. Make : Cera/Hindware/Parryware

S & F for low level flushing cistern, of 10 ltrs capacityPVC valveless,syphonic action type,white with inlet,ball valve,float and handle,flush pipe, incl brackets complete all as specified, .

S & F for Wash Hand basins, Vitreous China, white, flat back, size 550x440mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing & supply of, waste pipe, taps) complete all as specified and directed.

S&F CP bottle trap with wall connection pipe & wall flange complete all as specified. Make:- CERA F8060401 / Parryware T3201A1 / Hindware F850015

S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks three layered, (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including 20mm dia GI medium grade over flow pipe , approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed. Make : Syntex/ Vectus/Plasto

S & F of 20 mm bore ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F of 15 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F of 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.Make : Jaquare Cat Part No VGP 81001/Hindware Cat Part No F370001/Parryware Cat Part NoG9802A1

S & F of 15 mm bore stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. Make : JAGUAR Cat Part No OHS-35497/Hindware Cat Part No F-850073

S&F for brass chromium plated shower rose 125mm dia, swivel type, with CP arm, suitable for 15mm dia GI pipe. Make:- Pearl / Cera / Prayag / Jaquar

S&F 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make: Jaquar Cat Part No ALI-85037/Hindware Cat Part No F-370004/Parryware Cat Part No S-9906.

S & F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

M&L for PVC floor trap 75 mm outlet, plain with grating including joning with solvent cement complete all as specified and as directed by Engr-in-Charge.

M&L for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

All as per item No 113.00 here in above but in wall complete all as specified.

M&L for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L for 110 mm bore PVC (SWR) vent cowl

M&L PVC (SWR) bends with access door of 110mm bore any radius complete all as specified.

M&L 150mm internal dia salt glazed stoneware drain pipe Gde 'A', laid in trenches and jointed in cement & sand mortar (1:1), complete all as specified and directed.

M&L for concrete in PCC (1:3:6) type C-2 ( using 40 mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for Providing precast cement concrete M-20 nominal mix type B-1 (using 20 mm graded crushed stone aggregate) set in cement mortar (1:4) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L for cement concrete type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in cills, steps, copings, kneelers, apex stones, bed plates, and like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for construction of soakage well, internal dia 1.80M dia & overall depth 4.50M including excavation in any type of soil complete all as specified and shown on TD drawing & directed.

S&F SS 304 Grade Drappery rod with wooden finished decorative incl brackets, decorative finals at both ends & curtain rings 8 Nos (Min) complete all as specified.

Provn of 25 users septic tanks exc in ordinary soil, foundation in PCC (1:2:4) brick work in CM (1:4) RCC slab cover including RCC precast man hole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers as shown on TD drawing, complete.

S & F for Vitreous China bowl type urinals, size of 465x355x265mm white(minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in surface channel/drain including necessary formwork internal surface of drain finished even and smooth using extra cement complete all as specified.

M&L for 75 mm thick factory made precast fibre reinforced cement concrete Grade M-20 manhole drain cover (1st quility) including groove and hook arrangement for lifting and placing in position and sides coverd by MS sheet 2mm thick including 40 mm dia holes made in the slabs to drain runoff etc complete all as specified and directed by Engr-in-Charge. Make : NTC, Jain tiles

S&F single piece slim concealed flushing cistern with wall mounting frame, installation kit and S type drain pipe, connecting set for wall hung WC with cover plate fixed with WC complete all as specified and directed. Make : Jaquar Cat Part No JCS-WHT-2400WS, Cover plate Part No JCP-CHR-852415 or equivalent in hindware/ Cera

S&F 75mm X50mm single rebate factory made 100% PVC/ WPC door frame made 100% head free (single extruded process) material with density 750 Kg/Cum and manufactured by ISO 9001:2015 complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick moulded PVC/ WPC fafctory made 100% solid door (compulsory as per ISO : 4020) made from 100% head free style extruded with 2, 4 or 6 raised panel design or front side with 10mm deep mould on size side with wood grain texture and back side plain with density not less than 600 Kg/Cum complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore chromium plated fancy type sensor pillar tap high pressure with or without letter hot or cold with long screwed shank and fly nut screwed to GI pipe complete all as specified and directed. Make : Jaguar Cat part NO SNR-CHR-51021A or equivalent of Hindware

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down cement plaster on brick or stone wall, etc including racking out joints, hacking for keys, scrubbing down with water, etc complete all as specified and directed.

S&F stainless steel 304 grade grab bar vertically closed fixed to wall with nut bolts and holdfast all as specified and directed by Engr-in-charge. Make : Jaguar Cat Par No WAC-SAP-BG0800CS or equivalent of hindware.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr.-in-charge of following. Note:- Wiring shall be terminated in sunken modular boxes. Modular boxes shall be paid under respective items of this BOQ. Wire/cable colour coding shall be maintained properly as per IE rule. The make of conduit & its accessories should be Precision/Polycab/AKG. The make of wire should be Polycab/L&T/KEI

(a) One light/bell point controlled by one-one way switch.

(b) One ceiling /Exhaust fan Point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board.

All as per item No.135.00 here in above but with 2.5 Sqmm. (nominal area) wire/cable for phase and neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable, FRLS 1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

S&F moduler switch piano flush, button type 6 Amp SP one module one way complete all as specified Make : Legrand model Britzy Cat No 6734 01 eqvt in L&T model entice/ Havells model Murano.

S&F moduler switch piano flush button type 16 Amps SP one module one way complete all as specified Make : Legrand model Britzy Cat No 6734 11 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet multipurpose 3 Pin 6 Amp two module complete all as specified & directed. Make : Legrand model Britzy Cat No 6734 52 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet two in one three pin 6 Amp and 16 Amp two module flush type complete al as specified.Make : Legrand model Britzy Cat No 6734 55 eqvt in L&T model entice/ Havells model Murano.

S&F moduler bell push 6 Amp one module one way complete all as specified. : Make : Legrand model Britzy Cat No 6734 04 eqvt in L&T model entice/ Havells model Murano.

S&F 4 step modular electronic fan regulator flush type 2 module.Make : Legrand model Britzy Cat No 6734 31 eqvt in L&T model entice/ Havells model Murano.

S&F sunken box with flush metal GI box 1/2 module suitable for modular complete all as specified and directed directed.

All as per item no 143.00 here in above but 3 module.

All as per item no 143.00 here in above but 4 module.

All as per item no 143.00 here in above but 6 module.

All as per item no 143.00 here in above but 8 module.

S&F combind cover plate white 1 module suitable for modular switches. Make : Legrand model Britzy Cat No 6734 91 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 2 module suitable for modular switches. Make : Legrand model Britzy Cat No 6734 92 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 3 module suitable for modular switch/socket. Make : Legrand model Britzy Cat No 6734 93 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 4 module suitable for modular switch/socket. Make : Legrand model Britzy Cat No 6734 94 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 6 module suitable for modular switch/socket. Make : Legrand model Britzy Cat No 6734 96 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 8 module suitable for modular switch/socket. Make : Legrand model Britzy Cat No 6734 98 eqvt in L&T model entice/ Havells model Murano.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed iron/steel suction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr.-in-charge of following. Note:- Wire/cable colour coding shall be maintained properly as per IE rule. The make of conduit & its accessories should be Precision/Polycab/AKG. The make of wire should be Polycab/L&T/KEI

(a) One light/bell point controlled by one-one way switch.

(b) One ceiling /Exhaust fan Point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board.

All as per item No.154.00 here in above but with 2.5 Sqmm. (nominal area) wire/cable for phase and neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable, FRLS 1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

S&F switch piano flush type single pole one way 230 Volts 6 Amp complete all as specified and directed.

Supply and fixing Switch piano flush type single pole, one way, 230 volts 15/16 Amps ISI marked . Complete all as specified and directe.

S&F socket outlet 3 pin, 230 Volts 5/6 Amps flush type multipurpose 5 pin complete all as specified and directed.

Supply and fixing Socket outlet multipurpose having provision for 3 pin, 230 Volts 15/16 Amp and 3 pin, 5/6 Amp piano flush type ISI marked complete all as specified and directed.

S&F bell push flush type 5 Amps 230 Volts single pole complete all as specified and directed.

S&F step type fan regulator flush type 230 volts 6 Ampds 120 watts.Make HPL/Havells/Polycab

S&F lamp holder polycarbonate insulated body with back plate with and incl LED lamp retrofit 9/10 watts complete.

S&F Bell Ding dong 250V AC complete all as specified & directed. Make: SSK/Leader/Anchor.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete . Make: SSK/Leader/Anchor

S&F wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 4000K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Wipro Cat part No LL20-281-XXX-65AL1/ Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED840SPCWH.

S&F mirror light decorative compact luminarious with decorative ends caps 9/10 watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size. Make:- Havells/ Edgelite or equivalent in Philips

S&F Decorative Square/Round surface mounted LED flat panel PDC aluminium housing and PMPA diffuser makes it a robust Luminaire 12 Watts PF 0.9 and above operating voltage 150V-300V colour temp 4000K & lumen input output 70 Lumen per watt incl provisioning of 3 core white flexible multistranded copper conductor 23/0.0076 from ceiling rose to light connector complete all as specified and directed by Engineer-in-charge Make : Crompton cat part No LCDN-12-CDL/TL/WW/Wipro cat No LD80-101-XXX-60-XX/Philips Cat No DN092B LED10S-3000-PSU-WH

S&F Decorative wall mounting light SS finish fixture made up of Polycarbonate with opel glass diffuser suitable for LED/retrofit lamp 15 watts including LED/GLS lamp complete all as specified and directed by Engineer-in-charge Make : Havells cat part No LHJC01206499 or eqvt in Philips/Mepro.

S&F Decorative wall mounting light SS finish fixture made up of Polycarbonate with opel glass diffuser suitable for LED/retrofit lamp 15 watts including LED/GLS lamp complete all as specified and directed by Engineer-in-charge Make : Havells cat part No LHJC02108499 or eqvt in Philips/Mepro.

S&F Energy saving Bulk head luminaire with opal diffuser with and including retrofit LED lamp 10 watts complete all as specified and directed by Engr-in-charge. Make : Philips/CG/Havells

M&L for Bldg Security light fitting and Supply and fixing LED Street light luminaire comprising of pressure die cast aluminium housing heat resistant toughened glass IP-65, photovoltic LDR sensor with separate surge protection 5KA, 35 Watts or near higher size with making all arrangement for fixing light fitting such replacement of GI pipe bracket made of 40 mm bore medium grade pipe made to shape of 1200 of 70 cm and 50 cm to a overall length of 1.2 mtr for fixing of street light fitting including MS clamps of size 32 x 3 mm flat iron, nuts, bolts and washers of required size painting complete with all necessary electric connection etc all as specified and directed as per Greenstar Cat No: DSS3 or equivalent in Philips /Havells.

Supply, fixing and Testing TPN DB VTPN 4 way 415 Volts, 50 Hz indoor type double door Sheet metal enclosure IP-43 DB's flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable managenment including mounting arrangement for DPX3 MCCB 160 Amps four pole 415 volts as incomer including connection terminal strip complete and SP or SPN MCB's as out going etc complete pre wired with suitable size copper conductor. The DB's should hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Engr-in-charge Make: Legrand/L&T/Simens.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 12 way IP-43 DB's suitable for one MCB SPN as incoming and 10 MCB SP as out going, mounting flush on wall/concealed complete all as specified and directed by Engr-in-charge. Make: Legrand/L&T/Simens.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 4 way IP-43 DB's suitable for one MCB SPN as incoming and 2 MCB SP as out going, mounting flush on wall/concealed and making good distubed surfaces complete all as specified and directed by Engr-in-charge. Make: Legrand/L&T/Simens.

S&F MCCB 125 Amps four pole 415 volts thermal magnetic release ICU=100% ICS having breaking capacity 16 KA including connection terminal strip complete all as specified & directed Make:Legrand/L&T/Simens.

S&F MCB SPN 240 Volt 10 KA 40 Amp 'C' series conforming to IS complete all as specified & directed. Make: Legrand/L&T/Simens.

S&F MCB single pole 240 volt, 10 KA, 40 Amp, 'B' series confirming to IS complete all as specified and directed. Make: Legrand/L&T/Simens.

M&L for Sub main wiring P+N+E with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) drawing in and including 20 mm dia or higher medium duty PVC concealed conduit / PVC conduit on wall and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly complete all as specified & directed. The make of conduit & its accessories should be Precision/Polycab/AKG. The make of wire should be Polycab/L&T/KEI

M&L forSub main wiring P+N+E with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium duty PVC concealed conduit / PVC conduit on wall and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 6 Sq mm as earth wire upto common earth and connected to earth dolly complete all as specified & directed. The make of conduit & its accessories should be Precision/Polycab/AKG. The make of wire should be Polycab/L&T/KEI

Supply and fixing wall mounted type sheet metal single pole and neutral enclosure with a two pin and earth plug and socket complete with and including MCB SPN 20 Amp 'C' series 10 KA mounted on DIN rail channel and suitable plug complete all as specified and directed by Engr-in-charge Make: Legrand Cat No 5078 14 or eqvt in L&T /Simens. (Note : Item rate including all items ie base box, plug, socket , MCB etc complete)

Supply & fixing Wall mounted Air circulated fan of oscillating 450mm sweep, 100 watts, 1400 RPM, having Aerodynamic metal blades & high torque motor, Ribs guard safety,Jerk free oscillation & smooth noiceless running having thermal overload protection complete all as specified and directed by Engineer-in-charge. Make : Havells V3 / Orient Torado wall II/ Crompton Model Strom II WM .

S&F Ceiling fan1200mm sweep 65 watt white coloured, single phase 230V, including connecting with three core 23/0076 copper wire from ceiling rose to fan connector complete with new hooks 50 X 6 of MS plate made to suitable shape and welded with truss adjusting necessary fan rod, length as per site requirement after necessary threading/cutting/drilling holes as required at site complete all as specified and directed by Engineer-in-charge.Make : Crompton Model Mount Breeze/Orient Model Summer pride /Havells SS390.

Supply & fix Double ball bearing motor, Heavy duty exhaust fans totally enclosed, Rust proof body & blades, Aluminium pressure die cast, Dynamically balanced blades for vibration free & Noiseless operation, AC single phase, 6 pole power input 55 or higher wattage, 900 RPM or higher rpm, 230/ 240 V of size 300 mm sweep with provision of suitable louver & 3 core white flexible multistranded copper conductor 23/0.0076 from ceiling rose to fan connector complete all as specified and directed by Engineer-in-charge. Make : Havells : Turbo force 1 phase/ Crompton model EXHD300-6-1(ISI) marked or equivalent in Orient.

M&L for making suitable size hole in wall for fixing exhaust fan of size upto 300mm sweep in any type of wall including grouting of four nos hold fastners/Tee bolts of suitable size etc for fixing of exhaust fans with wall complete all as specified and directed complete all as specified & directed

S&F Geyser Vertical Storage type of capacity 25 Ltrs ISI marked having Stainless steel storage tank of capacity 25 ltrs , rock wool insulation, 2 KW element, thermostat, system On/Off indicator lamps, safety valve, pressure release valve, inlet & outlet connections with suitable size hot and cold PVC nylone braided pipes 2 Nos connected to water supply line complete including three core power cord with 15 Amp top, having minimum 5 star rating as per BEE certification including grouting of four nos hold fastners/Tee bolts of suitable size etc for fixing of geyser to wall complete all as specified and directed Make : Havells Pro code GHWAMGSWH050 or equivalent in AO Smith/Jaquar

Supply and laying UG Cable, XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 16 Sqmm 4 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge. Make of Cable : KEI / Havells/ Grandlay.

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed. (Note:- punned thickness shall measured)

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply and laying of GI Steel tubing medium grade 50 mm (2") dia including all fitting laying in trenches or grouting/fixing in wall for protection of cable complete all as specified and directed by Engineer-in-charge Make : TATA/Swastik/ Suryaprakash

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore, and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

Supply, laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminiium conductor, 1100 volts cross sectional area 25 sq. mm 4 Core all as directed. Make Havells/Polycab/KEI/Grandlay

Supply and fixing of LT panel double door outdoor type with Bus Bar chamber of min size 800 mmx600 mm x450 mm dust and vermin proof made out of 2.0 mm CRCA sheet, front opening including supplying and fixing under mentioned items and cable entry provision for, duly powder coated on both sides with locking arrangement mounted on and including PCC platform 45 cm above ground and 45 cm below ground, angle iron legs made of 50x6 mm angle iron complete all as specified and directed.

(a) MCCB 63 Amps four pole 16 KA (legrand/L&T/Indoasian/ABB) -01 Nos

(b) Astronomical Timer Switch Digital Typen - 01 No Make-,Legrend/L&T/Havells

(c ) Contactor 40 Amps four pole (legrand/L&T/Indoasian/ABB) - 01 No

(d) Indicating Lamp set of three - 01 Nos

(e) Ammeter Digital type -01 Nos

(f) Voltmeter digital type -01 Nos

(g) Phase reversal switch for motorized winch 01 No

Supply and fixing of Busbar chamber of size 600x450x214 mm or higher size with PVC hinged lid suitable for and mounting arrangement for fixing of MCCB 4 pole, duly connected with and incl 04 Nos of copper Busbar 300 Amps fixed on epoxy insulators, Gun metal cable gland of 25 Sqmm 01 No and PVC coupler for sub main wires 04 Nos complete Polycarbonate type (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV resistant, having high grade gasket made of Polyurethane, flame retardant,complete all as directed at site by Engr in charge or his rep complete. Note:- Only MCCB shall be measured and paid for seperately all other items incl connection of MCCB to busbar incl thimble, bottle lugs etc and fixing arrangement ie clamp, bracket etc as directed by Engr in charge are included in item rate. Make:- Hensel/ABB/BCH/Schneider/Cape

Supply and fixing of MCCB 63 Amps FP 415 Volts having breaking capacity 15 KA with and incl spreader link kit complete suitable for fixing as incoming in polycarbonate busbar complete all as specified and directed. Make:- Legrand/Schneider/Siemens/L&T/Hager

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized strip of 32x6mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 40 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSr part 1 including testing on completion all as specified and directed. NOTE 1. The unit rate includes for protection pipe 40 mm dia and GI strip 32x6 mm from top of earth plate up to 7.5 meter above ground level.

RAMAPATI ENGINEERING SERVICES

MOHAN LAL GUPTA