PROVISION OF SEPTIC TANKS FOR WASHROOM, DIESEL GENERATOR FOR CONFERENCE HALL, SPECIAL REPAIR TO MET COMPLEX P-102 AT NAE AND SPECIAL REPAIR TO BLDG NO. P-88 AT MES COMPLEX

Amount

Taking down chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified

Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified

Taking down Shutters of any description exc 2 sq. m each and removing to store all as specified.

S&F fiber glass reinforced plastic (FRP) door frames of three legged of cross section 90 x 45 mm having single rebate of 32 x 15 mm to receive shutter of 30 mm thick. The laminate door frame moulded with fire retardent grade unsaturated polyster resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block of 2nd Class Hardwood in all the three legs. The frame shall be covered with fibre glass from all side M.S stay shall be provided at the bottom to sedy the frame complete as per direction of Engineer - in - Charge.

S&F 30 mm thick glass fiber reinforced plastics paneled door shutter of required colour & approved colour and manufactrures made with fire retardent grade unsaturated polister resin,moulded to 3mm thick FRP laminate for forming hollow rails & styles with wooden frame & suitable blocks of seasoned wood inside at required places for fixing of fittings along with MS tube frame of 19 gauge all around the styles & rails duly coated with steer primer cast monolithically with 5mm thick FRP laminate forpanels & conforming to IS:14856:2000 including fixing to frames. The shade & colour shall be approved by Engineer-in-Charge

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings complete all as specified

S & F Plain colour PVC sheet 2mm thick fixed or laid on to aluminium doors by using rubber based adhesive, supplying & fixing at site as per manufacturers specification

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-chargecomplete all as specified.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge

S&F Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples all as specified.

S&F 4.8 mm thick Sheet glass,ordinary quality pin headed type and glazing with Aluminium snap beading with rubber Neoprene packing in square exc 0.5 sq. m in each pane all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from metal frames or stone, concrete or brick surrounds, including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed

S&F 300mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 250mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 200mm long (Length of Bolt in mm) Aluminium anodised,barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 150mm (Size of Handle in mm) Extruded aluminium alloy handles, fabricated type,anodised all as specified.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints with commercial face veneers complete all as specified and directed

S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified.

S&F 30mm thick 1st class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed

S&F 100mm Butt hinges(Size of hinges in mm), medium weight, cold rolled, stainless steel, and fixed all as specified.

S & F in repair to ( incl Dismantling ) 18-19mm thick pre-laminated particle board, flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade having one side decorative lamination and other side balancing white lamination as in cup board shutter , shelves etc including 6 mm thick teak wood leaping on three sides and 20mm thick on hanging side & French polishing to edging complete all as specified.

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed

M&L for plaster of paries ceiling surfaces to make ceiling smooth and making any design at the covers and around for boxs etc complete in all aspects and as directed by Engineer in chargeire mesh including any sunk or raised mouldings (fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and directed

S & F Providing and applying of silicon sealent in construction joint, window glass,polycarbonate sheets and required places to make joints water tights, after racking out of joints/cracks wherever necessary & throughtout cleaning at different level complete all as specified and as directed.

S&F 12 mm thick toughened glass for door, partition etc. of any size and side portions of toughened glass fixed to wall / floor, joints sealed with clear silicon silicate gel to make water tight, edges with diamond cut including taper drilling to flush the screws / all fitting as required, floor hinges, patch fitting top, bottom and sides, SS lock and SS handles 300-400mm, spider joint etc. and floor door spring as per requirement all as specified, required at site by manufacturer instructions and complete all as specified and directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exc 1.5 sqm complete all as specified and directed.

Refixing aluminium decogrills in the same opening including cutting of decogrills if required etc all as directed

S&F mortice lock/latch 100mm with two levers (vertical type), mild steel body and fixed all as directed

S&F more rebates for aluminium anodised frame and shutters for door, winodows and ventilators or partitions with one or more rebates power coated including jointing cleats for fixing etc complete with power coating any colour minimum thickness 50 micron all as specified and directed. Note:- (Section of Aluminium should be Jindal section )

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

S&F 600x450 mm beveled edge looking mirror wall mounted backlit (white and warm light) of superior premium quality glass without frame with chromium plated brass screws and cup washers as in repair complete all as specified.

S&F in repair ceramic white / coloured wash basin, scratch resistant, easy clean glaze, modern bathroom sink including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified.

S&F in repair of 15mm bore pillar tap, (foam flow), wash basin tap, brass with chrome finished, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, as in repair complete all as specified.

S&F in repair of Vitreous China wash down water closet pan (European type) with P or S trap, snow white or white colour, fixing bolts, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete, excluding flushing cistern and flush pipe including seat cover as in repair complete all as spd and directed by engineer in charge

S&F in repairs of Viterious china wash hand basin white flat back of size 550x400 mm ,including brackets,waste coupling and waste pipe , or fixed with existing plateform surfaces with sealent with white cement etc complete all as specified and directed.

S&F in repair Bib taps, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in bore of dia 15mm complete all as specified and as directed.

S&F in repair Stop valves, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in bore of dia 15mm complete all as specified and as directed.

S&F in repair Health faucet, single function superior elite quality including wall hook including making connections and fixed in position complete in all respect as specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premisess complete all as specified and as directed

M&L for joint free non-skid ceramic tiles, coloured (of approved shade and design), 7 to 8mm thick, of superior quality, square / rectangular (area exceeding 0.18 Sqm but not exceeding 0.38 Sqm) joint free, as in floors, etc.set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:4) complete all as specified and as directed

M&L for virified ceramic tiles premium quality, coloured (of approved shade and design), 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, on vertical surfaces such as skirting / dado / risers of step etc.,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fixed over & including backing coat of 10mm thick plaster in CM (1:4) complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons, compound wall etc.laid dry beded in any mortor complete all as specified.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite including grinding and polishing complete all as specified

M&L 20mm thick Granite (of any type) tiles machine cut (table rubbed and polished), in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including backing coat of 10mm thick plaster in CM (1:4) including grinding and polishing complete all as specified

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Repair to door, window , ventilator by spot welding in repairs exceeding2.50 cm but not exceeding 5.0 cm in length thickness of metal to be welded not exceeding 6.0mm thick, complete all as specified and as directed by Engr in charge. Note : Welding work wil be carried at site by arrangement of welding machine without any extra cost to the Govt

Repair and refixing of aluminium window shutter to make it openable/slide smoothly, including cutting, repair/change of all necessary fittings/fixtures for window like cleates , locking arrangements glazing cleats and cadmium plated stainless steel screws including rubber gaskets beadings etc complete all as specified and as directed by Engr in charge

S&F in repair rotational moulded water storage tank (cylinderical vertical with closed top ) hoisted and fixed in position capacity 500 ltrs with 25mm bore brass float valve etc connections all as specified in SSR Part I Complete all as spd and as directed by Engineer in Charge

S&F in repair Rotational moulded polyethylene water storage tanks of cap 1000 Ltr Cap (cylindrical vertical with closed top) hoisted and fixed in position with inlet outlet with 25mm bore brass float valve etc connections all as specified in SSR Part I Complete all as spd and as directed by Engineer in Charge.

Supplying and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 16mm pipe outer dia, Complete all as specified and directed.

Supplying and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 20mm pipe outer dia, Complete all as specified and directed.

Supplying and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 25mm pipe outer dia, Complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with screws complete all as specified & directed by Engr-in-charge.

S&F anodised aluminium snap grid frame work for false ceiling all as specified complete all as specified & directed by Engr-in-charge.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling snap grid of size 605 x 605 mm complete all as specified and directed by Engr in Charge.

S&F Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/curved surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh including any sunk or raised mouldings (fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and directed

M & L for wall care putty 3mm thk on Ceiling and applying two coats of oil bound distemper.all as specified directed by Engr in charge

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and Labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for preparation of new surface and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete as specified and directed.

M& L for preparation of old plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces to prepare the surface even and smooth of required shade and colour as per manufacturer's specification complete all as specified and directed.

M& L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth and distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification complete all as specified and directed

Material and labour for preparation of old surfaces of ceiling including cornicess plaster etc for lime wash (white washing) and applying one coat of white wash on ceiling complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint on steel or iron surfaces of any decription, over 10 cm in width or grith, not othewise described including preparation of old painted surfaces complete all as specified and directed.

S&F in repair 600x450 mm beveled edge looking mirror wall mounted superior premium quality glass without frame with chromium plated brass screws and cup washers as in repair complete all as specified.

S&F in repair Vitreous China waterless urinals, bowl type complete including waterless key valve with key adaptor and nut, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including of fixing supply pipe to urinal spredder, trap and urine waste pipe complete all as specified and directed. Make : CERA, HINDWARE, JAQUAR

S&F in repair ceramic white / coloured table top wash hand basin, scratch resistant, easy clean glaze, modern bathroom including cutting for and pinning in ends of brackets or erecting stand incl fixing of supply and waste pipe complete all as specified. Make - CERA, HINDWARE, JAQUAR

S&F in repair Vitreous China soap tray/dishany type, fixed to plugs with chromium plated brass screws complete all as specified. Make - CERA, HINDWARE, JAQUAR

S&F in repair Glass shelf assembly complete all as specified. Make - CERA, HINDWARE, JAQUAR

S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. Make - CERA, HINDWARE, JAQUAR

S&F 15mm bore single lever wash basin mixer tall, (foam flow), brass with chrome finished, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, as in repair complete all as specified. Make - CERA, HINDWARE, JAQUAR

S&F in repair, vitreous china wash down water closet pan, 'Pedestal' pattern (EWC) integral foot rest or without foot rest including jet spray, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete complete all as specified and directed. Make - CERA, HINDWARE, JAQUAR

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in bore of dia 15mm complete all as specified and as directed. Make - CERA, HINDWARE, JAQUAR

Taking down old roof treatment of any description including plaster, cement concrete etc. and removing old material outside MD land exc 1Km and not exceeding 5 Km completely all as specified and directed by Engineer - in - Charge.

M&L for 10 mm thick (average) plastering on concrete surfaces in cement mortar 1:4, in order to maintain proper slope and base over existing roof surfaces for laying of APP based polymeric membrane, add WPC @3% of cement weight(WPC paid separately), finished even and smooth without using extra cement complete all as specified and as directed. (Note:- Polymeric membrane will be measured and paid separately)

Supply only integral waterproofing compound

M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment/ specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 4 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non wovwn polyster fabric or weight not less 160 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm minimum) and then inserted insde the groove of parapet wall and shall be finished by a membrane flashing. (Note:- (i) Laying of APP based membrane shall be done by torch on method or as per manufacturers instruction. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instruction. (c ) Applying two coats of reflective Bituminous aluminium paint on top of APP membrane.

M & L for Complete removal of existing treatment on roof surfaces incl necessary taking down and wirebrush the surfaces to remove existing cement mortar roof surfaces and providing Cement concrete of 40mm thick roof topping of type B-1,1:2:4 (20mm gradedaggregate) over two coats of damp proof course over plastered surface to prepare the surface even and smooth. complete all as per manufacturer's instructions and as directed by Engineer-in-Charge.

Dismantling of mild steel work of any description not otherwise provided for all as specified and directed .

M&L for steel rolling/sliding shutter of 1.25mm thickness of laths (motorised and manually operated-both), with ball bearing, shaft spring, hood cover including top cover, an-choring rod, hasp and staple, gear operated type with chain wheel and hand chain and one shop coat of primer; erected in position as indi-cated, including locking arrangement as per manufacturers instructions complete fixed in repair all as specified and directed by Engr-in Charge.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling all as specfied and directed

M & L for Preparation of new steel sufaces of any description ,over 10 cm width or girth and applying 2 coat of synthetic enamel paint over a coat of red oxide primer.

S & F 150mm bore CPVC Schedule 40 pipes & Plain Schedule 80 fittings & fittings on walls/ceiling or in any length with rubber ring joints, fixed to walls with clamps complete all as specified and as directed by the Engineer-in-Charge

S & F 150mm bore PVC (SWR) bends of any radius, complete all as specified

S&F ball valves, high pressure of PTMT with epoxy coated aluminium long rod & highdensity plastic big ball screwed for iron pipe including necessary extension nipple and tank nipple suitable for HDPE water tank with check nut complete and fixed of the following size as in repair :-

15 mm bore

20 mm bore

25 mm bore

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (unreinforced) complete including removing debries ouside MD land all as specified and directed.

S&F except interlocking tiles filling with sand cushioning (where ever required) including levelled with existing tiled surfaces complete all as spd and directed by Engineer in Charge ( Note :- Sand and PCC shall be paid and measured Separtely )

M&L for sand filling 50mm thick under paver blocks for cushion complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade, finished with grey cement and pigment, complete all as directed.

M&L cement conc 1:4 :8 type D-2 (40mm graded agg) in foundatin filling and mass concrete.complete all as specifed and as directed by Engineer in Charge.

M & L for 50mm thick cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, floor topping etc , surfaces finished of concrete flooring with brooming complete all as spd including provision of necessary construction joints filled with bitumen filler etc complete all as directed by Engr-in-Charge

M & L for precast RCC cover slab for drain in 1:2:4,Type B1 (20mm graded aggregate) set in cement mortar 1:6 complete all as directed by the Engr-in-Charge

Surface excavation n.exc 30cm deep and averging 15 Cm and getting out in hard/dence soil complete all as specified and directed.

Excavation over areas n.exc 1.5 m deep & getting out in hard dense soil.

Excavation over areas n.exc 1.5 m deep and getting out in soft/ desintegrated rocks.

Excavation over areas exc 1.5 m deep and n exc 3.00m and getting out in soft/ desintegrated rocks.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc and getting out in Hard / dense soil complete as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc and getting out in Soft/disintegreated rock complete as specified and directed.

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Removing excavated material as soft disintegrated rocks exc 50m and exc 250m, and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Removing excavated exc 250 m but n.exc. 500 m and deposited where directed at a level n.exc. 1.5m above the starting point, as in soft/disintegrated rocks, complete.

Returning filling in hard/dense soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as directed.

Returning filling in soft/disintegrated rock including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as directed.

M&L for maroom/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

M&L for Hard core, using broken stone or boulders of guage n.exc. 63mm, deposited, spread and levelled in layeres n.exc. 15 cm thick, watered and rammed to a true surface, as in below sub base, plinth protection and ramp, complete all as directed by Engr-in- Charge.

M&L PCC 100 mm thick, type C-2, 1:3:6 (40mm graded aggregate) as in sub-base, complete all as directed.

M&L for 75mm thick PCC 1:3:6 type C2 as in plinth protection complete all as specified and directed.

M & L PCC 1 : 3 : 6 Type C2 ( 40 mm graded aggregsate) as in foundation and mass concrete. complete all as specified and directed.

M&L for damp proof course 40mm thick in PCC 1:2:4 type B0 with incl WPC @ of 3% of cement weight to horizontal or vertical surface including necessary formwork complete all as specified and directed.

M & L Concrete bed 1 : 3 : 6 Type C2 for drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M & L Reinforced concrete pipes, class NP3, 150mm laid and jointed complete with collars complete all as specified and directed.

M&L Providing cement concrete in coping with type C1 1:3:6 (20 mm graded aggregate).

Demolition of brickwork or stone/boulders/block masonry, built in cement mortar including all quoins, arches, pillars, ashlar facing, dressed stonework, precast concrete artilcles and precast concrete block walling etc. Complete all as specified and directed.

M&L PCC Block masonary in CM 1:4 brought to courses, complete all as specified & directed by Engr-in-charge.

M&L PCC Block masonary in CM 1:6 brought to courses, complete all as specified & directed by Engr-in-charge.

Rendering 15mm thick on concrete work in CM 1:4 finished the surfaces even and smooth using WPC @ 3% of cement wt (WPC paid separately)

M&L 15 mm thick Internal plastering in CM 1:6 finished even & smooth without using extra cement and applying sagol finish complete.

M&L for RCC type M-30 (using 20 mm graded aggregate) foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; rough finished surfaces of conrete flat complete all as specified and directed.

M&L for precast reinforced cement concrete M-30, using 20mm graded stone aggregate as in baffle wall including use & waste of form work for fair finished surfaces complete all as specified and directed.

M&L for RCC M-30, using 20 mm graded stone aggregate as in lintel including necessary use and waste of formwork for fair finished surface of concrete..

M&L for structural steel as in screen.

M&L for Reinforced cement concrete M-30, using 20mm graded stone aggregates as in cover slab n exc 200 mm thick.

M&L form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200mm thick for fair finish surfaces.

M&L for precast reinforced cement concrete M-30, using 20mm graded stone aggregate as in cover slab including use & waste of form work for fair finished surfaces complete all as specified and directed.

M&L for precast reinforced cement concrete M-15, factory made including reinforcement of required size using 20mm graded stone aggregate set in CM(1:4) as in cover slab ( for manhole etc)including use & waste of form work for fair finished surfaces complete all as specified and directed

M&L for mild steel as in rungs

M&L for precast reinforced cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in block including use & waste of form work for fair finished surfaces complete all as specified and directed.

M & L Mild steel CRS TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

Ditto all as per above item No. 130.00 but 8 mm dia

Ditto all as per above item No. 130.00 but 8mm dia in stirrups

S & F of 100mm dia AC vent cowl.

S & F of 100mm dia AC pipe.

S & F of 100mm dia AC pipe bend.

S & F of 75mm dia Sand Cast iron soil,waste and vent pipes, in any length with or without ears, with cement joints, laid in tenches or in floors.

S & F of 75mm dia Cast iron cowls.

M&L for loose filling with aggregates (broken stone or boulders) of gauge 80 to 150 mm in soakage pits, soakage wells

M & L preparing surface of newly plastered walls and applying two coats of oil bond distemper over chalk whitening preparatory to distempering.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410-W(Gde- E- 250)quality-A-

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W(Gde- E- 250) quality-A-

S & F Mild steel bolts exc 12mm and not exc 20mm dia of neck purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long

S & F Mild steel Round bars Fe-410-W Gde.E-250) quality-A or Fe 290 (Gde -E-165) 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (Sag Rod of 16 mm dia)

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Plain, galvanised, mild steel sheeting 0.63 mm thick , in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials for taking credit and making good disturbed surfaces of walls, floors, etc

M & L for point wiring with PVC insulated unsheathed stranded copper conductor cable FRLSH of size 1.5 sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including in concealed conduit non metallic, rigid PVC conduit of adequated size with all fittings and conduit accessories including suitable size modular metal flush box and modular white cover plate with frame for housing the switches, socket outlets, including all necessary wall cutting and making good disturbed surface all as directed and specified. Note : Cutting chase and making good to match with the adjoining surface shall be included in the unit rate.

One light point control by one switch

One ceiling fan/exhaust fan control by one switch

Ditto all as per above item No. 147.00 but wire 2.5 sq mm cable for One 3 pin socket 5 Amps on the same board with other switches

Ditto all as per above item No. 147.00 but wire 2.5 sq mm cable for One 3 pin socket 5 Amps socket as independent board

Ditto all as per above item No. 147.00 but wire 4.0 sq mm cable for switch socket outlet 3 pin 15 Amps with 4.0 sq mm as earth continuity conductor.

S & F Modular switch 1 way 6A, 1 module all as specified and directed by EIC.

S & F modular Socket, 6A - 2/3 pin combined 2 module all as specified and directed by EIC.

S & F Socket 16A - 2/3 pin combined 2 module, all as specified and directed by EIC.

S & F Modular switch 1 way 16A, 1 module all as specified and directed by EIC.

Supply and fix ceiling rose three terminal ll as specified and directed by EIC.

Supply and fixing Modular fan regulator120Watt, 2- module , AC 240 Volts complete.

Taking down fan of any make/type/sweep,sealing cable end ,dismantling of blades and for repair /overhauling complete all as directed

M &L for Overhauling of ceiling fan /wall fan/exhaust of any make and sweep after opening and cleaning rotor bearing and stator properly and oiling/greasing of bearing/ bushes, reassmbling the same, and testing on completion all as specified and as directed .(Note- (A) Overhauling of ceiling fans will be carried out at AGE E/M Yard only. (B) The spares (bearing , bush,capacitor) required shall be measured and paid separately in the relevant items).

Repair of ceiling fan, segregation of unserviceable parts, cutting and removing out copper winding, cleaning the armature, rewinding of fan armature with appropriate gauge of super enamelled copper wire with necessary insulating materials such as vertex paper, cotton tape, PVC insulation tape etc varnishing with approved grade of insulation varnish and heating up, re-assembling the fan complete with replacement of unserviceable spares parts, (spare parts will be measured & paid separately) including necessary lathe work for fixing of bush/bearing greasing the same with approved grade of grease, making all electrical connection and supply and fixing the following items and including necessary transportion to workshop, for 1200/1400/1500mm sweep fan :- (i) Split pin - 02 Nos (ii) Connection block - 1 No (iii) Insulation rubber bush - 01 No

Fixing or hanging only ceiling fan/exhaust fan after overhauling/repair of winding above and connecting up including provision of 3 core 1.5 Sqmm cable from ceiling rose or connector to fan( max up to 1m length) all as specified and directed

M &L for Painting of ceiling fan/Exhaust Fan/Wall mounted fan of any sweep complete including fan blade down rod with synthetic enamelled paint by spraying including cleaning and removing dust by polish paper and dirt and making smooth surface for painting ,filling cavities with filler complete all as specified and as directed

Supply and fixing in replecement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing in replacement LED light fitting 1x 20 Watt,220 V AC decorative box type with driver , holder including LED tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

S & F in replecement MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail ,240Volts SPN with 12 way Double door , IP-43-IK09 protection

S & F in replecement MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 40 to 63Amps

S & F in replacement MCB SP 6-32 Amps 'C' Series complete all as specified and directed.

S & F in replacement Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps

S & F in replacement Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable FRLSH 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through and including PVC CASING CAPING/PVC Conduit not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 4 sqmm and one wire of 4.0 sqmm and one run of PVC casing caping/Conduit shall be measured as one unit.

S & F in replacement Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable FRLSH 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC CASING CAPING/PVC Conduit not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 6 sqmm and one wire of 6.0 sqmm and one run of PVC casing caping/Conduit shall be measured as one unit.

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and as dierected.

M&L Earthing with 600X600X6 mm thick , galvanised steel earth plate electrode buried vertically in ground (Earth pit not less than 2.25 meter deep below normal ground level ) with top edge of plate vertically at a depth ,not less than 1.5 m below ground level connected to and including GI strip of size 32X6 mm by means of bolts,nuts,check nuts, And washer of galvanised steel, Gi shrip to be provide upto the extent of 7.5 m GI strip to be duly connected to metalic bodies of HT/LT equipment with provision of mixture of charcoal dust & common salt packed all ground the earth plate upto MS funnel with wire mesh provided inside concrete earth pit for watering arrangement,complete all as shown on electrical plate no.3 of SSR Part I (2009) and testing on completion.

S& F XLPE insulated armoured and pvc sheated heavy duty electric cable size 3.5 core , 95 Sqmm cross sectional area with aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete Note- rate is inclusive of cable gland & cable lugs

S& F XLPE insulated armoured and pvc sheated heavy duty electric cable size 3.5 core , 50 Sqmm cross sectional area with aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete Note- rate is inclusive of cable gland & cable lugs

S& F XLPE insulated armoured and pvc sheated heavy duty electric cable size 3.5 core , 35 Sqmm cross sectional area with aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete Note- rate is inclusive of cable gland & cable lugs

S & F in replacement XLPE insulated armoured and pvc sheated heavy duty electric cable ,3-1/2 core 25 Sqmm cross sectional area aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in trenches passing through pipes /ducts including testing complete all as specified and as directed.

Supply & JOINT cable jointing kit heat shrinkable 1.1KV XPLE straight through joint of size 25 sqmm 3.5 core to 50 sqmm 3.5 core cable size complete. Make:-Denson/3M/Raychem

S& F laying of Double Walled Corrugated (DWC) HDPE pipe of size 90/75 mm outer/inner dia of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

S& F laying of Double Walled Corrugated (DWC) HDPE pipe of size 63/50 mm outer/inner dia of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge Make:-ASTRAL TELEREX /eqivalent as approved by GE

Supply and installation of silent Diesel Engine driven generating set of capacity 58.5 KVA 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with relay panel,AMF Panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per CPCB -IV+ norms and necessary foundation as per OEM specification and necessay canopy / shed for protection from rain etc.

ENGINE Direct Injection, 3 cylinders, Water cooled, Compression Ignited, Turbo charged, and Charge Air-cooled diesel engine developing 74.1 hp at 1500 rpm & complying with BS5514 / ISO 3046 standards. Besides standard components, the engine will be complete with: • 12V electrical starting system consisting of Starter motor, charging alternator. • Dry type Air cleaner with restriction indicator In-line Fuel injection system with Electronic Governor • Spin-on Lube oil filter elements • Radiator, Air- to- Air After cooler, pusher fan & fan drive arrangement • Gear driven water pump • Sensors for Oil pressure, Coolant temperature & level. • First fill of Lube oil. (API CI4 grade)

ALTERNATOR 3 Phase, 4 Wire, Self excited, self regulated Brushless Single Bearing Type; Class H insulated AC generator developing 58.5 kva at 415 V, 0.8 PF (lag) with IP23 protection.

CONTROL PANEL Control panel is 14 gauge sheet steel fabricated, dust & Vermin proof & will be complete with internal wiring. The following Protection / Control / Display / Annunciation features are provided for the DG set. • MCCB of adequate rating • Indicating lamps for DG ON & LOAD ON. • Key switch • Set of Current transformers • Set of control fuses

INTEGRATED DG SET CONTROLLER • Monitoring engine speed, oil pressure, coolant temperature, frequency, voltage, current, power and fuel level, the modules will give comprehensive engine and Alternator protection. • This will be indicated on the largest back-lit LCD icon display in its class via an array of warning, electrical trip and shutdown alarms. • With a number of flexible inputs, outputs and protections, the modules can be easily adapted to suit a wide range of applications including lighting towers with the added option for staged loading outputs. The unique integrated DG set controller incorporates both engine and alternator parameters in one console .This micro-processor based controller provides the most exhaustive display of critical engines and alternator performance parameters with alarm and safety features.

INTEGRAL DG SET CONTROLLER PARAMETERS 1) DISPLAY PARAMETERS - Engine oil pressure ,Coolant temperature ,Fuel level indication %,Battery voltage ,Engine RPM , DG set hours run , Generator- volts , Generator –current , Power factor , Kw-hr , Kw. 2) AUDIO-VISUAL WARNING - Low oil pressure, High coolant temperature, Low battery voltage, Low fuel level. 3) SHUT-DOWN WITH AUDIO-VISUAL ANNUCIATION- Low oil pressure, , High coolant temperature, Engine over speed, Engine under speed, Under voltage, Over voltage ,Over frequency, Under frequency ,Low water level, High canopy temp.

GENSET COMFORMANCE STANDARDS Compliance Standards – Engine BS 5514 / ISO 3046 Compliance Standards- Alternator IS 4722 / BS 5000 Compliance standards – DG set ISO 8728 / Noise pollution norms of MoEF & certified by ARAI,Pune. DG set Rating - Prime rating as per ISO 8728. 10% overload provision available for intermittent periods. The RTU DG set is supplied with the following standard accessories • Inbuilt control panel with complete internal wiring /cabling. • Residential silencer –mounted with complete exhaust piping. • 12V 88 AH battery • Inbuilt fuel tank

Supply and fix manual Change over switch panel of capacity 125 Amps manually operated for 57 KVA DG Set with enclosure SS of 1.6 Guage thickness all as specified and directed Make :L&T or equivalent

J J ENTERPRISES (BID ID -3404082)

OM ENTERPRISE (BID ID -3404177)

m/s prakash enterprise (BID ID -3391474)