Modernization of IMFL Shops at Haddo, Sri Vijaya Puram

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer

M.S. tube

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

One or more coats on old work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :

For fixed portion

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing 12 mm thick BWP 710 marine plywood with 1 mm thick lamination of required colour on the existing wall with with necessary screws, nuts etc. complete as per the direction of Engineer in-charge.

Providing and fixing factory made height adjustable metal shelves(heavy duty) 4 shelves (7x3 feet) end cap rack of approved quality

Providing and fixing heavy duty slotted angle racks of approved quality

Providing and fixing of "L" shaped Billing Counter with 19 mm thick BWP 710 marine plywood with 1 mm thick lamination on exposed area including pedestal drawers with casotrs, flap door, side door, all necessary fittings & adhesives etc. all complete as per drawing and as per the direction of Engineer-in-charge.

Providing and fixing of Name Board in Backlit Acrylic sheet with "Logo, ANIIDCO LIQUOR STORE" of size 5.00 x 0.60 m etc. all complete as per drawing and as per the direction of Engineer-in-charge.

Providing and fixing of Price List Board in Backlit Acrylic sheet of size 1.20x2.40m, separate for Premiunm & Regular shop, all complete as per drawing and as per the direction of Engineer-in-charge.

Electrical

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

4 Module (125mmX75mm)

6 Module (200mmX75mm)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing of 6W LED new series of LED spot light specially designed for commercial usage long life with 30000 burning hours with CRI>80 wide Make:- Crompton FAME spot Cat No.CDR-211-06-30/40 SL-NWH 3000K/4000K complete with all accessories etc. as required.

Supplying and fixing of 2ft 20-watt LED Tubelight Make:- Bajaj/Havells/ Phillips/K-Lite complete with all accessories etc. as required.

M/S JOY KUMAR BISWAS (BID ID -55955)