GE-K-59-2021-22 -SPL REPAIR OF LIVING BLDG NO T 09 AND SPL REPAIR TO REWIRING OF OR COOK HOUSE AND SOME OTHER MINOR WORKS AT DRAS STATION UNDER GE KARGIL

Amount

Surface excn not exc 30cm in deep and averagig 15 cm in deep and getting out in hard/dence soil

Excavation over area and n.exc 1.5m in deep and getting out in hard/dense soil

Excavating in trenches n exc 1.5 m in depth for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard / dense soil

M& L PCC 1:4:8 type D-2 (using 40mm graded stone agg) in foundation, filling and mass concrete.

M&L precast cement concrete type C-1, 1:3:6 using 20mm graded stone aggregates, block masonry with solid blocks, exc 10cm width and setting cement mortar 1:6 complete.

Returning filling incl spreading leveling watering and well ramming in layers not exceeding 25 mm in any type of soil.

Removing excavated material n.exc. 50 m and deposited were directed at a level n.exc.1.5 m above the starting point

Earth filling in floors including spreading, levelling and ramming with watering as required in layers n.exc 25cm thick.

Hard core of broken stones or boulders of gauge in exc 63mm deposited spread and levelled in layers n. exc 15cm thick incl watering and rolled to true surface.

M&L 75mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base to floor as specified.

M&L PCC type B1 1:2:4 (20mm graded aggregate) 40mm thick as in floor finished surfaces even and smooth with using extra cement

M & L for taking down cement plaster on brick or stone wall etc indliding raking out joints, hackiong for key, and scrubing down with water and all as specified by engr in charge.

M&L for 10mm thick CM (1:4) rendering onbricks or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified.

M&L for 15mm thick CM (1:6) rendering on fair surfaces of bricks or concrete work complete all as specified.

M&L for racking out joints/pointing to block in course masonry or concrete block walling in cement mortar complete all as specified

M&L for preparationof new plastered surfaces on walls and applying two coats of cement based paint over a coat of primer.

Demolition of Cement Concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and as directed

M&L for 25mm thick PCC type B0, 1:2:4 (using 12.5mm graded stone aggregate) as in base of floor tiles to floor complete all as specified

M&L for screed or bedding layer 15 mm thick in cement mortar 1:6 finished even and fair on floors for laying floor finishes.

M&L Non skid Ceramic coloured tiles 7 to 8mm thick area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for non skid ceramic tiles7 to 8 mm thick area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over 15 mm screed bed in CM 1:6 all as specified and as directed by engr in charge.

M&L for Glazed ceramic coloured tiles in vertical surface of size 350x450x7mm thick as in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile.

Roughing surfaces of old concrete floor by picking ,sweeping clean and washing down with water to remove dust etc.

Brushing neat cement slurry with 3.0 kg of cement per sq mtr.

M&L for pre-polished cut kota stone slab flooring of size 600x600x20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20mm thick screed bed in cement mortar 1:6

M&L 0.63mm thick glavanised, corrugated mild steel sheeting with two corrugation side lap fixed with 'L' type or 'J' type hook bolts in lies of coach screws with grade of zinc coating 275gm per Sqm etc complete all as specified and directed

S & F 0.63 mm thick galvanised plain mild steel sheeting in ridge roofs , walls etc with grade og zinc coating 275 , complete all as specified and directed by engg-in charge.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed

S&F Rolled mild steel Gde Fe-290 (gde E-165) as in Roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framimg (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc.

M & L for steel work in tubular trusses including special shaped washer et, complete using EWR or induction butwelede tube confirming IS 1161-1979 anf all as specified by Engr in charge.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Steel ventilator with top hung shutter including hinges steel peg stay complete all as specified

S&F 2nd class softwood (KAIL) as in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

Taking down shutter of any description n.exc 1 sqm each.

Taking down shutter of any description exc 1 sqm and n.exc 2 sqm each.

S&F 35mm thick 2nd class soft wood (KAIL) plain framed panelled shutters (any No of pannels) with panels of timber flat on both sides (Feather edgeed), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed

S&F 30 mm thick 2nd class soft wood (KAIL) glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers

S&F 100 mm butt hinges medim weight cold rolled mild steel fixed with screws or welded all as directed.

S&F 75mm mild steel butt hinges medium weight , cold rolled complete all as specified and as directed by Engr-in-Charge

S&F 200mm long Aluminium anodisedl barrel tower bolt of extruded section and fixed complete all as specified and as directed

S&F anodised aluminium barrel tower bolt extruded sections 150 mm size.

S&F 125mm extruded aluminium alloy handles febricated type anodised complete all as specified and as directed

S&F 100mm extruded aluminium alloy handles febricated type anodised complete all as specified and as directed

S&F 300mm Aluminium alloy, anodised,sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed

S&F harrison rails, mild steel, chromium plated with fixing brackedts, stops rollers etc and all as specified and directed

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beading in square n exc 0.5 sqm complete all as specified

M&L for preparation of wood and wood based material surface of any description description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and as directed

M&L prepation of new or previously untreated surfaces on steel of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L PCC 1:3:6 type C2 ( using 40 mm grade aggregate) 75 mm thick as in plinth protection/paving complete all as specified and as directed

S&F vitreous china wash down water closet pan (pedestal pattern), , white (excluding fixing bolts, flushing cistern and flush pipe all as specified

S&F plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified

S&F PVC flushing cistern valveless syphonic action type flushing cistern low level 10 Ltrs white with inlet ball valve float and handle incl bracket.

S&F pillar tap 15 mm bore cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed and fly screwed for iron pipe and fixed fancy type.

S & F WHB counter sunk type ovel under/over counter shape in fixed & on stone slab incl necessary cutting etc complete all as spcifed and directed.

Providing precast cement concrete Type B-1, 1:2:4 (20 mm graded aggregate) as in door lintel etc and similar articles with plain frames set in CM1:6 ,all as specified and directed.

Providing precast cement concrete Type B-1 1:2:4 (20 mm graded aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs,mangers,shelves and similar articles with plain frames set in CM1:6 ,all as specified and directed.

M&L for reinforcement cement concrete (nominal mix) type B1 (1:2:4) (using 20mm graded crushed stone aggregate) in foundation , including rafts, footing,foundation beams, plinth beams, bases for coloums etc.complete all as specified and directed

M&L for RCC (nominal mix) in cement concrete Type B1 1:2:4 (20mm graded aggregate) in chimneys, and shafts, square or circular in shape etc and similar works

Use and waste form work to soffits of suspended labs, floor slabs, landing and similar work n.exc 200mm thick with rough finished flat surfaces of concrete etc. complete all as specified and directed

M&L for Formwork to rough finished surfaces of concrete to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floor and beams

S&F framed work such as grill, grating etc, with ends of bars shouldered or rivited or forged into spikes, framed guard bars barred iron doors, ladder baluster walk ways, ralling, frame work of water tanks & similar work conforming to Fe-290 Gde 165

M&L for Plain, black mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings 0.80mm complete all as specified

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required inclduing cranking bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90 mm dia or securing with clips.

M&L mild steel TMT bars 6 to 8mm dia cut to length bent to shape required inclduing cranking bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90 mm dia or securing with clips.

M&L for providing 15-18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, cooking platform etc and like in cemnt mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/blankets, any thickness, including cover fillets all as specified and as directed

S&F 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails on wall to timber rame work complete, all as specified and directed

M&L 9mm thick prelaminated particle board, interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with nails to timber frame work as in ceiling.

M&L second class soft wood (KAIL), plain fillets, square or rectangular in setion of area exc 13 and n exc 25 Sqcm, clean sawn, secured with nails.

Ditto but wrought and area exc 3 and n exc 6 Sqcm as in cornices moulding

S&F PVC (SWR) floor trap, plain with grating including joinery with solvent cement diameter of outlet 75mm

S&F PVC (SWR) pipes single socketed any length, with rubber rings joints laid in floors 75mm dia bore floor trap, plain with grating including jointing with solvent cement, diameter of outlet 75mm dia bore.

S&F PVC (SWR) pipes single socketed any length, with rubber rings joints laid in floors 75mm dia bore floor trap, plain with grating including jointing with solvent cement, diameter of outlet 110mm dia bore.

S&F PVC pipe waste pipe 32mm dia and 75cm long incl waste coupling fixed to waste coupling.

S&F bib tap 15 mm bore cast type copper alloy with round handle screwed down screwed for iron pipe or brass ferrule.

S&F 15mm dia GI tubing medium grade with all fittings fixed in floors or fixed to walls or ceiling, in any length, bore complete all as specified and as directed

S&F 20mm dia GI tubing medium grade with all fittings fixed in floors or fixed to walls or ceiling, in any length, bore complete all as specified and as directed

S&F PVC connection15mm size, with PTMT nuts of length 600mm

M&L for PCC type B-1 1:2:4 (using 20mm graded aggregate) as in coping complete all as specified

M&L PCC 1:3:6 type C2 (40mm graded aggregate) as in surface channels and drains

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms moulds, mitred/stopped ends etc

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc.

M&L for Point wiring with multi-stranded copper conductor PVC insulated and unsheathed cable in PVC casing and capping, 1.5 Sqmm with all fittings/accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth including closed recessed wooden terminal Boxes of suitable size made of 2nd class hard wood for mounting switches, sockets etc with 3mm thick laminated sheet cover for one light point or bell/buzzer point controlled by one switch, complete.

All as per Srl item No 85 here in before but for one 3 pin socket outlet 5 Amps on independent board.

All as per Srl item No 85 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps independent board.

S & F Switch piano flush type 5 Amps, single pole one way.

S & F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type.

S & F Switch socket combination 2 in 1, 5 and 15 Amps flush type.

Supply and fixing in LED 1x18 Watt, 220 V, AC decorative box type with driver, holder including LED tubelight connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F in Ceiling rose surface bakelite 65x50mm, two to three terminals.

Supply and fixing in LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Dismantling of existing MCB box, MCBs, rectangular box, service bracket from surface for replacement with new one.

S & F in replacement Sheet metal enclosure for DB's Single door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required. Complete all as specified and directed.

Supply and fixing in replacement 240 V 10 KA C curve miniature circuit breaker (MCB) SPN 40 to 63 Amp in the MCB DB complete with connection testing and commissioning.

Supply and Fixing in replacement of Isolator, Triple pole and neutral, 32 to 63 Amp, 415V, 10 KA , complete all as specified and directed by the Engr-in-Charge.

Supply and fixing in replacement 240 V 10 KA C curve miniature circuit breaker (MCB) SP 5 to 32 Amp in the MCB DB complete with connection testing and commissioning.

Supply and Fixing in replacement of Isolator, single pole, 32 to 40 Amp, 240V, 10 KA, complete all as specified and directed by the Engr-in-Charge.

PVC rectangular block for mounting switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size 200x150x50 mm deep

M&L for House Service bracket (hook type) complete with 3.0 m long G.I pipe 40 mm dia (medium grade), two numbers 90° bends, M.S hook and stay including taking down the existing unserviceable bracket. NOTE :- The unit rate shall to include for :- (a) Cutting holes in walls etc. of any description, grouting rag bolts and making good with cement mortar 1:3 including making good finishing to match the existing work and removing rubbish off the premises as directed (in case of bracket being fixed to masonry wall). (b) G.I pipe house service bracket hook type fabricated out of 3.0m long screwed G.I pipe of medium grade and comprising of two number 90° bend (pipe dia) screwed tight to the top ends of the service vertical limb, the two ends of the service provided with two number of turned spit tight fit, well seasoned teak wood bushing and the bracket fixed plumb vertical against the wall with two number flat iron clamps (fabricated out of 50 x 6mm flat iron with 4 No. 16 mm dia ragged bolts of appropriate size with screwed ends, tightened with 16 mm dia nuts with 6 mm thick washer against the clamp tightening collar.

Dismantling of existing service cable and submain wiring including casing caping from existing surface for replacement

S & F Sub main wiring with two single core 6 sqmm multistranded copper conductor cable, PVC insulated cable 1100 volts grade and 6 Sqmm as continous earthing drawing and including PVC casing and caping of suitable size with all acessories, complete all as specified.

M&L in Replacemet of Earthing complete with galvanised steel earth plate electrode 600mm x 600mm and 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connected to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel as shown in electrical plate No. 3 conected to earth test point as specified or indicated including testing on completion.

S&F in replacement 1100 volts grade heavy duty 10 sqmm 3 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 01 metre apart including 4 mm suspension complete all as specified.

S&F in replacement 1100 volts grade heavy duty 10 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 01 metre apart including 4 mm suspension complete all as specified.

S&F in LED light fitting 1x9W/1x10W bulkhead luminaries including LED light driver holder connecting up three core flexible copper conductor cable of suitable size.

Note : Deduction for amount of Rs 16,520.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

M/S UNIVERSAL ENGINEERS

Ashfaq Construction Company