Construction of 2x3.15MVA, 33/11KV Substation at Nakote along with associated 10Km LILO line on ACSR Dog Conductor on turnkey basis in District- Tehri Garhwal

Amount

33 KV Material

33/.433 KV 63 KVA Station Transformer

Line Isolator, 800A, 33KV

Bus Isolator, 800A, 33KV

33 KV, 1250A, 3 Phase O/D type, VCB 24 V DC

CT Out door with , 33 KV CTR 200-100/1-1 A

CT Out door with , 33 KV CTR 400-200/1-1 A

Junction box FOR CT

Junction box FOR PT

33 KV/110 V O/D type PT.

33 KV Lightening Arrester

33 KV Post Insulator

33 KV Fuse Set

Control & Relay Panel 33 KV Double Fdr , 24 V DC

Control & Relay Panel 33 KV Double T/F, 24 V DC

33 KV 3x50 sq. mm. XLPE cable from Bus gantry to station transformer

33 KV XLPE cable 3Cx300mm sq.

33 KV Cable jointing kit 3Cx300 mm2 out door/indoor type

G.I. Pipe 5/6" mm2 dia 3 mtr long

11 KV material

11 KV Aluminium 3x185 sq. mm. XLPE cable from T/F to incomer VCB

Cable jointing kit outdoor type suitable for 3x185 sq. mm. XLPE cable

Cable jointing kit indoor type suitable for 3x185 sq. mm. XLPE cable

11 KV Aluminium 3x120 sq. mm. XLPE from outgoing VCB to out going feeder poles

Cable jointing kit outdoor type suitable for 3x120 mm XLPE cable 11 KV.

Cable jointing kit indoor type suitable for 3x120 sq. mm. XLPE cable

HT Cable warning tape

11 KV VCB I/C 350MVA, 600/300/5A,

11 KV VCB FDR 350MVA, 400/200/5A,

11 KV B/C VCB Panel 350/500 MVA

Cable jointing kit indoor/outdoor type suitable for 3x50 sq. mm. XLPE cable 33 KV.

LT control cable

LT Cable Al. 4Cx70 Sq.mm.PVC for Stn. T/F to ACDB.

LT Control Cable

i. 10C x 2.5 Sq. mm.

ii. 4C x 2.5 Sq. mm.

iii 2C x 2.5 Sq. mm.

Perforated tray 400 mm width for cable trench

Perforated tray 200 mm width for cable trench

Perforated tray 100 mm width for cable trench

Making cable trench.including fabrication, fixing of MS angle 50/40X6 mm size (excluding cost of MS angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal etc.

DC Instruments

24 V Battery charger with boost & trickle charge

24 V Battery set Maint. Free

DCDB 24 V

AC Instruments

S.T. Pole 8 mtr. Long S.P.-10

Cost of LT PVC cable 4x10 sq. mm.

Cost of LT PVC cable 2x6 sq. mm.

Iron clad 30 Amps DP switch on the ST pole. (Water Proof)

50W, LED lamp with control gear & mounting accessories (Branded Make,Philips ,oreva,havells,surya,syska,orpat,C&G)

30W, LED lamp with control gear & mounting accessories(Branded Make,Philips ,oreva,havells,surya,syska,orpat,C&G)

Earthing work

MS Round 32mm dia, 6.21 Kg/mtr for earth mat, electodes for earth mat & delta earthing

G.I. Strip 65x6 mm.

G.I. Strip 40x6 mm.

M/S FLAT 50X6

Special chemical earthing by treatment of soil with highly conducted material like combination of bentonite, conductive cement, coke dust, sodium carbonate, MgSo4, NaCl & CaCl2 as per ISS 3043-1987 as per annexure -A (including cost of all material & labor)

MS item

MS (Rail, RS joist , MS Channel & MS angle, MS flat, MS plate, MS reinforcement bar as per RESSPO/Approved drawings) for Misc. structures for TG, BG, LA, CT, PT, Isolators, P.I., Fuse Sets stay support wire mesh fencing, gate support, cable trench, earthing cleat etc. design as per site conditions including fabrication, welding, nut & bolts, painting (primer plus two coats of aluminium/green paint) etc. complete in all respect.

Wire mesh fencing

Wire mesh fencing with gate duly painted on both side as per drawing.

Bus bar material

ACSR Panther conductor

MS Plate 225x225x8 mm.

MS Plate 400x400x8 mm.

33 KV Disc insulator Polymer,70 KN, B & S type

Disc fitting for Panther 70 KN

33 KV Disc insulator Polymer,120 KN, B & S type

Disc fitting for Panther 120 KN

PG clamp Panther to Panther

PG clamp Panther to Dog

Connectors suitable for Panther

1. For LA suitable for panther

2. For Isolators suitable for panther

3. For CT/PT suitable for panther/dog

4. For PI suitable for panther

5. For SF-6, VCB suitable for panther

6. For Fuse setsuitable for panther

7. For T/F suitable for panther

8. For T/F suitable for LT side

9. For station transformer suitable for dog/weasel

Flexible copper connection on neutral bushing of T/F 500X50 mm heavy duty with copper lug at ends.

Fire fighting equipments, furniture & testing equipments

Steel office table, Godrej, (5'x3')

Steel office table, Godrej, (4'x2.5')

Steel Almirah, Godrej,

Steel cabinet, Godrej,

Steel office chair, Godrej,

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain 12 mtr. Length

5 KV Megger Digital (Motwane, Fluke,)

2.5kv Megger Digital (Motwane, Fluke,)

Earth Megger Digital (Motwane, Fluke,)

Dust bin

door mat

Isolation transformer

Rubber mat 1 mtr. wide x 2 mtr long and 12 mm thick to withstand 11 KV dielectric strength as per IS 5424-1969. Along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet and Duly painted with red color including cost of all material, fabrication etc. complete work

Instruction board 3’x2½’ of mica board moulded with wooden frame duly painted & writing.

Single line diagram board of S/s size 2½’x1½’ mica board with wooden frame, duly painted & writing.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted & fixing at S/s with C.C. 1:4:8

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland etc.

11 KV outgoing DP structures of ST Pole SP-33 and SP-55 OFstation T/F

S.T. Pole 8.5 mtr. Long SP-23

S.T. Pole 11 mtr. Long SP-55

11 KV Polymer disc insulator B & S

11 KV disc fitting for weasal

G.S. Stay set GI 1800x16 mm comp.

Stay wire 7/10

MS Earthing rod 20x2500mm

GI Wire 6 SWG

11 KV TPMO complete

11 KV lightening arrestor

11 KV fuse set.

P.P. & Clamps for S.T. Pole (SP-23)

Bracing Clamp for ST Pole (SP-23) Top & Bottom

Stay clamp for ST Pole (SP-23)

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

GI pipe 4" dia, 3mtr long

33 kv station t/f structure

P.P. & Clamps for S.T. Pole SP-55 with nut & bolts

Clamp of required size for holding cable supporting angle, pipe, cable & bus isolator handle on double pole & bus bar gantry

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

GI pipe 4" dia. 3mtr long ( for double pole & bus bar gantry)

Insulators for holding earthing strip of lightening arrestor & transformer neutral

G.I.pipe 40/50 mm out.dia. & thickness 4/5 mm, 6 mtr. Long for making opearting mechanism for vertical bus isolator

Description of Work / Item(s)

Amount

33 KV Material

3 MVA, 33/11 KV Transformer including Insured Carriage of Power Transformers from Electricity Store Center to substation site including safe loading, unloading at nearest point of the transformer plinth.

33/.433 KV 63 KVA Station Transformer

Line Isolator, 800A, 33KV

Bus Isolator, 800A, 33KV

33 KV, 1250A, 3 Phase O/D type, VCB 24 V DC

CT Out door with , 33 KV CTR 200-100/1-1 A

CT Out door with , 33 KV CTR 400-200/1-1 A

Junction box FOR CT

Junction box FOR PT

33 KV/110 V O/D type PT.

33 KV Lightening Arrester

33 KV Post Insulator

33 KV Fuse Set

Control & Relay Panel 33 KV Double Fdr , 24 V DC

Control & Relay Panel 33 KV Double T/F, 24 V DC

33 KV 3x50 sq. mm. XLPE cable from Bus gantry to station transformer

33 KV XLPE cable 3Cx300mm sq.

33 KV Cable jointing kit 3Cx300 mm2 out door/indoor type

G.I. Pipe 5/6" mm2 dia 3 mtr long

11 KV material

11 KV Aluminium 3x185 sq. mm. XLPE cable from T/F to incomer VCB

Cable jointing kit outdoor type suitable for 3x185 sq. mm. XLPE cable

Cable jointing kit indoor type suitable for 3x185 sq. mm. XLPE cable

11 KV Aluminium 3x120 sq. mm. XLPE from outgoing VCB to out going feeder poles

Cable jointing kit outdoor type suitable for 3x120 mm XLPE cable 11 KV.

Cable jointing kit indoor type suitable for 3x120 sq. mm. XLPE cable

HT Cable warning tape

11 KV VCB I/C,

11 KV VCB FDR,

11 KV B/C VCB Panel

Cable jointing kit indoor/outdoor type suitable for 3x50 sq. mm. XLPE cable 33 KV.

LT control cable

LT Cable Al. 4Cx70 Sq.mm.PVC for Stn. T/F to ACDB.

LT Control Cable

i. 10C x 2.5 Sq. mm.

ii. 4C x 2.5 Sq. mm.

iii 2C x 2.5 Sq. mm.

Perforated tray 400 mm width for cable trench

Perforated tray 200 mm width for cable trench

Perforated tray 100 mm width for cable trench

Making cable trench.including fabrication, fixing of MS angle 50/40X6 mm size (excluding cost of MS angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal etc.

DC Instruments

24 V Battery charger with boost & trickle charge

24 V Battery set Maint. Free

DCDB 24 V

AC Instruments

S.T. Pole 8 mtr. Long S.P.-10

Cost of LT PVC cable 4x10 sq. mm.

Cost of LT PVC cable 2x6 sq. mm.

Iron clad 30 Amps DP switch on the ST pole. (Water Proof)

50W, LED lamp with control gear & mounting accessories (Branded Make,Philips ,oreva,havells,surya,syska,orpat,C&G)

30W, LED lamp with control gear & mounting accessories(Branded Make,Philips ,oreva,havells,surya,syska,orpat,C&G)

Earthing work

MS Round 32mm dia, 6.21 Kg/mtr for earth mat, electodes for earth mat & delta earthing

G.I. Strip 65x6 mm.

G.I. Strip 40x6 mm.

M/S FLAT 50X6

Special chemical earthing by treatment of soil with highly conducted material like combination of bentonite, conductive cement, coke dust, sodium carbonate, MgSo4, NaCl & CaCl2 as per ISS 3043-1987 as per annexure -A (including cost of all material & labor)

MS item

MS (Rail, RS joist , MS Channel & MS angle, MS flat, MS plate, MS reinforcement bar as per RESSPO/Approved drawings) for Misc. structures for TG, BG, LA, CT, PT, Isolators, P.I., Fuse Sets stay support wire mesh fencing, gate support, cable trench, earthing cleat etc. design as per site conditions including fabrication, welding, nut & bolts, painting (primer plus two coats of aluminium/green paint) etc. complete in all respect.

Wire mesh fencing

Wire mesh fencing with gate duly painted on both side as per drawing.

Bus bar material

ACSR Panther conductor

MS Plate 225x225x8 mm.

MS Plate 400x400x8 mm.

33 KV Disc insulator Polymer,70 KN, B & S type

Disc fitting for Panther 70 KN

33 KV Disc insulator Polymer,120 KN, B & S type

Disc fitting for Panther 120 KN

PG clamp Panther to Panther

PG clamp Panther to Dog

Connectors suitable for Panther

1. For LA suitable for panther

2. For Isolators suitable for panther

3. For CT/PT suitable for panther/dog

4. For PI suitable for panther

5. For SF-6, VCB suitable for panther

6. For Fuse setsuitable for panther

7. For T/F suitable for panther

8. For T/F suitable for LT side

9. For station transformer suitable for dog/weasel

Flexible copper connection on neutral bushing of T/F 500X50 mm heavy duty with copper lug at ends.

Fire fighting equipments, furniture & testing equipments

Steel office table, Godrej, (5'x3')

Steel office table, Godrej, (4'x2.5')

Steel Almirah, Godrej,

Steel cabinet, Godrej,

Steel office chair, Godrej,

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain 12 mtr. Length

5 KV Megger Digital (Motwane, Fluke,)

2.5kv Megger Digital (Motwane, Fluke,)

Earth Megger Digital (Motwane, Fluke,)

Dust bin

door mat

Isolation transformer

Rubber mat 1 mtr. wide x 2 mtr long and 12 mm thick to withstand 11 KV dielectric strength as per IS 5424-1969. Along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet and Duly painted with red color including cost of all material, fabrication etc. complete work

Instruction board 3’x2½’ of mica board moulded with wooden frame duly painted & writing.

Single line diagram board of S/s size 2½’x1½’ mica board with wooden frame, duly painted & writing.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted & fixing at S/s with C.C. 1:4:8

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland etc.

11 KV outgoing DP structures of ST Pole SP-33 and SP-55 OFstation T/F

S.T. Pole 8.5 mtr. Long SP-23

S.T. Pole 11 mtr. Long SP-55

11 KV Polymer disc insulator B & S

11 KV disc fitting for weasal

G.S. Stay set GI 1800x16 mm comp.

Stay wire 7/10

MS Earthing rod 20x2500mm

GI Wire 6 SWG

11 KV TPMO complete

11 KV lightening arrestor

11 KV fuse set.

P.P. & Clamps for S.T. Pole (SP-23)

Bracing Clamp for ST Pole (SP-23) Top & Bottom

Stay clamp for ST Pole (SP-23)

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

GI pipe 4" dia, 3mtr long

33 kv station t/f structure

P.P. & Clamps for S.T. Pole SP-55 with nut & bolts

Clamp of required size for holding cable supporting angle, pipe, cable & bus isolator handle on double pole & bus bar gantry

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

GI pipe 4" dia. 3mtr long ( for double pole & bus bar gantry)

Insulators for holding earthing strip of lightening arrestor & transformer neutral

G.I.pipe 40/50 mm out.dia. & thickness 4/5 mm, 6 mtr. Long for making opearting mechanism for vertical bus isolator

LAYING OF 33 KV CABLE

Laying of 33 KV Cable by excavation of cable trench upto 1 mtr in mixed soil properly laying of the cable by placing bricks on both side & top of the cable filling of 250 mm layer sand from the top so as to cover the cable completely and then filing excavated soil upto 300 mm then spreading of cable warning tape & covering of the trench completely with excavated mixed soil, compacting the soil upto ground level including cost of sand, first class bricks, etc.

Civil works

Gravel pitching of size 1/2" to 3/4" (20x30x0.1)

Earthfilling in yard

Excavation of earth in mixed soil

RR Masonary 1:6

Cement concreting in 1:4:8 ratio

Cement concreating in 1:3:6

Brick work in 1:4

Cement Plaster 1:4

Stone pad 300x300x75 mm.

Construction of Control Room Building at Construction of 2x3.15 MVA, 33/11 KV Substation Nakote, Distt-TEHRI GARHWAL

Land Development Works (Boundary Wall, Approach Road and Other Miscellaneous Civil Works) at 33/11 KV Substation at Nakote

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator )/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5m

Supplying and filling in plinth with Jamuna/local sand under floors including. Watering, ramming consolidating and dressing complete.

Earth filling under floor and in S/s area including cost of earth including its cartage watering, dressing, ramming in 20cms. thick layers and including all leads and lifts complete. (Rates Approved by SE Civil vide letter No. 410/E.C.C./A.O.R. dt-01-06-2012)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level 1:4 :8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 ( 1 cement :2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: 1:1:5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement. 1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral/ stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5 : 3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)

Centering and shuttering including strutting propping etc. and removal of form for: : Lintels, beams, plinth beams, girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting propping etc. and removal of form for:. Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chajjas, corbels etc. including edges.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (Cold Twisted Bars ).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (Cold Twisted Bars ).

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4( 1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 ( 1 cement : 4 coarse sand).

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with: Cement mortar 1:6( 1cement:6 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia 0.63 mm all complete With 12 mm mild steel U beading.

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. 125x65x2.12 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete 100x58x1.90 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete 75x47x1.70 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete 100 mm

Providing and fixing aluminium tower bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (200x10mm)

Providing and fixing aluminium tower bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (150x10mm)

Providing and fixing aluminium tower bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (100x10mm)

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complete: 125mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complete: 100mm

Providing and fixing aluminium hanging floor door stopper, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complete: Single rubber stopper

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complete: Twin rubber stopper

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge. Extruded section profile size 48x40 mm

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge. Extruded section profile size 42 x 50 mm

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Casement Window (Outward/Inward opening) with hinge System Frame (50 mm x 50 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Casement Window (Outward/Inward opening) with hinge System. Sash (Style and Rail) (62 mm x 34 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Casement Window (Outward/Inward opening) with hinge System. Mullion (intermediate Section) (66 mm x 50 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Casement Window (Outward/Inward opening) with hinge System. T’ Profile (one vertical length in between two shutters) (24 mm x 34.5 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Casement Window (Outward/Inward opening) with hinge System. Glazing bead (12 mm x 18 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Sliding Window (Two Track, 2/4 Shutters) Two Track Sliding Frame (67 mm x 52 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Sliding Window (Two Track, 2/4 Shutters) Sliding window Sash (60 mm x 44 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Sliding Window (Two Track, 2/4 Shutters) Sliding Interlock for Window (one vertical length in each shutter)( 45.5 mm x 28 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length. Sliding Window (Two Track, 2/4 Shutters) Sliding Glazing bead (35 mm x 18 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length.Sliding Door (Two Track, 2/4 Shutters) Two Track Sliding Frame (67 mm x 52 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length.Sliding Door (Two Track, 2/4 Shutters) Sliding Door Sash (80 mm x 44 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length.Sliding Door (Two Track, 2/4 Shutters) Sliding Interlock for Door (one vertical length in each shutter (45.5 mm x 28 mm)

Providing and Fixing factory made uPVC white colour casement/sliding window / door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in- charge. (Glazing, hardware hinges and fitting etc. to be paid separately.) Note :- Each member of window to be measured separately with clear length.Sliding Door (Two Track, 2/4 Shutters) Sliding Glazing bead (35 mm x 18 mm)

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.200 x 19 x 1.9 mm

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.250 x 19 x 1.9 mm

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.300 x 19 x 1.9 mm

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge. 350 x 19 x 1.9 mm

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge. 400 x 19 x 1.9 mm

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete.

Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete.

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing panelling or paneling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebated to be measured). Panelling for panelled and glazed shutters 25mm to 40mm thick: Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 25 mm thick confirming to IS:14587

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 12 mm thick.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 18 mm thick.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 25 mm thick.

Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade ( Grade-I) IS:14587:1998 marked one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickeled plated bright finishing M.S. piano hinges IS:3818 marked with necessary screwed complete

Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) IS: 14587:1998 marked, (one side decorative and other side balancing lamination) with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand complete. 18 mm Thick

Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) IS: 14587:1998 marked, (one side decorative and other side balancing lamination) with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand complete. 25 mm Thick

Providing and Fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with Top and Bottom rail of T-iron 40x40x6mm with 40 mm dia, steel pulleys completewith bolts, nuts, locking arrangement, stoppers, handles, including and applying primming coat of approved steel primmer.

Providing and fixing pressed steel door frames conforming to IS: 4351 manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and ifrequired angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge Fixing with adjustable lugs with split end tail to each jamb (Profile-C)

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.)

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20mm nominal size stone aggregate).

Providing and fixing glass strips in joints of terrazo/cement concrete floors. (40mm wide and 4mm thick)

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigement to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand): 25mm thick

Kota stone slabs 25mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement : 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bootle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3 (1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS; 15622 of approved make in colours such as White, lvory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 ( 1 cement :4 Coarse sand ) including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointin with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointin with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes (110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement : 6 coarse sand)

6 mm cement plaster of mix: 1:3 (1cement : 3 Fine sand)

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete

Distempering with oil bound washable distemper or approved brand and manufacture to give an even shade. New work (two or more coats) over and including water tinnable priming coat with cement primer.

Finishing wall with textured exterior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality ) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soil, waste and vent pipes: 100mm dia ( Sand cast iron S&S pipe as per IS:1729)

Providing and fixing soil, waste and vent pipes: 75mm diameter: ( Sand cast iron S&S pipe as per IS:1729)

Providing and fixing M.S. holder-bat clamps of approved design to Sand cast iron/cast iron(spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4mix( 1cement :2 coarse sand :4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 75mm dia. pipe

Providing and fixing plain bend of required degree. 100mm ( Sand cast iron S&S as per IS-1729)

Providing and fixing single unequal plain invert branch of require degree: 100x100x75mm (sand cast iron S&S as per IS-1729)

Providing and fixing terminal guard: :75mm (Sand cast iron S&S as per IS- 1729)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. 100mm inlet and 100mm outlet (Sand cast iron S&S as per IS: 3989).

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190gms

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anticorrosive bitumastic paint, cutting chases and making good the wall : 15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside with 75 class designation brick work in cement mortar 1:4 (1cement : 4coarse sand) for stop cock with C.I. surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10( 1 cement:5 fine sand :10 graded stone aggregate 40mm nominal size) and inside plastering with cemnt mortar 1:3 (1cement:3coarse sand ) 12mm thick finished with a floating coat of neat cement complete as per standard design . With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water stonrage tank ISI: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931 (15mm nominal bore).

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS Standards and weighing not leass than 690 gms. (15mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed ) of standard design and of approved make conforming to IS:8931. (15mm nominal bore)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 a(15mm nominal bore)

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing aluminium work for doors, windows ventilators and partitions with extruded built up standard tubular sections/ approprate Z sections and other sections of approprate make conforming to IS: 733 and IS: 1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : :For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows ventilators and partitions with extruded built up standard tubular sections/ approprate Z sections and other sections of approprate make conforming to IS: 733 and IS: 1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass/ stainless stell screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre- laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sqmm.FRLS PVC insulated copper conductor single core cable etc as requited. GROUP B

Wiring for circuit/submain wiring alongwith earthwire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required. 2X1.5 sqmm + 1X1.5 sqmm earthwire

Wiring for circuit/submain wiring alongwith earthwire with the following sizes of FRLS PVC insulated copper conductor , single core cable in surface/recessed PVC conduit as required. 2X2.5 sqmm + 1X2.5 sqmm earthwire

Wiring for circuit/submain wiring alongwith earthwire with the following sizes of FRLS PVC insulated copper conductor , single core cable in surface/recessed PVC conduit as required. 2X4 sqmm + 1X4 sqmm earthwire

S/F stepped type electronic fan regulator on the existing modular plate switch box including connection but excluding modular plate etc.as required.

S/F metel box of 180x100x60mm deep (nominal size) on surface/recess with suitable size of with phenolic laminated sheet cover in front including P/F 6 pin 5/6 and 15/16 amp 240 V socket outlet and 15/16 amp piano type switch, connection,painting etc as required.

S/F 8ways double door single pole and netural,sheet steel,MCB D.B 240 volts on surface/recess complete with tinned copper bus bar, netural bus bar, earth bar,din bar detachable gland plate,interconnections, power painted including earthing etc. as required. (But without MCB/RCCB/ISOLATOR) 2 + 6 Way/ 8 way, Double Door

S/F 5amp to 32amp rating, 240/415 volts, "C" curve MCB suitable for inductive load of following poles in the existing MCB D.B complete with connection,testing and commissioning etc. as required. Single Pole

S/F following rating, D/P, 240 volts, isolator in the existing MCB D.B complete with connection,testing and commissioning etc. as required. 40 amps

Earthing with GI earth plate 600 x 600 x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrengment and watering pipe 2.7 metre long etc. (but with charcoal or coke and salt) as required.

Providing & Fixing Bajaj/Havells/Orient or equivalent make ceiling fan 1200mm dia suitable for 230V,50Hz, single AC supply and complete with all standard acessories such as blades & capacitor etc. including installation, testing & commissioning complete in all respect. (Rate approved by SE Civil vide letter no. 106/ECC/extra item dated 13/1/2014

Supply & Fixing Bajaj/Havells/Orient or equivalent make simple batten super light 36/40W, 230V Cop. fluroscent tube fitting complete with all labour,material,T&P etc. required for proper completion of work. (Rate approved by SE Civil vide Letter no. 106/ECC/Extra Item Dated 13/1/2014)

S/F of Exhaust fan 30cm sweep of Bajaj/Havells or other approved quality with all material, Labour T&P etc complete. (Approved By S.E. Civil).

Description of Work / Item(s)

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed : All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. (All kinds of soil).

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. Hard rock (requiring blasting)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed. Hard rock (blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator )/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5m

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1: 2 : 4 (1 Cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: 1:1:5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) :

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: : Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (Cold twisted bars ).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (Cold twisted bars ).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6( 1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand :12 graded stone aggregate 20 mm nominal size). At plinth level with: Cement mortar 1: 6 ( 1 cement :6 coarse sand ).

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer susing structural steel etc. as required. (In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.)

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m².

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/ m².

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointin with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. (i) Single socketed pipes (110mm diameter)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm).

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter .(600 mm over all girth)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1cement :6coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire 9.38 kg per 100m (minimum) between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earthwork and concrete work to be paid for separately):- Payment to be made per metre cost of total length of barbed wire used. with G.I. Barbed Wire

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Supply of Stone Aggregate (Single Size) 20mm Nominal Size

Supply of Stone for Masonry Work

Description of Work / Item(s)

Amount

ST Pole 9 mtr long SP-33

ST Pole 11 mtr long SP-55

ST Pole 8.5 mtr long SP-23

ACSR Dog conductor

GS Earth wire 7/16 SWG

V-type channel cross arm 33 KV

V-type channel cross arm 11 KV

MS Channel 125x65x6 mm (0.30 mtr.)

33 KV Top channel 125x65x6 mm (3.2 mtr. Long)

MS Channel 125x65x6 mm (3.5 mtr. Long)

MS Channel 100x50x6 mm (4+2+1+0.35=7.35 mtr.)

Cross bracing set 65x65x6 mm (3.5x2=7 mtr.)

MS Angle 65x65x6 mm (4 mtr.)

33kv polymer Pin with pin and Nuts

Disc fitting for DOG conductor

33 KV Polymer Disc Insulator

Disc Insulator 45 KN B&S type POLYMER

Stay set 20x1800 mm

Stay wire 7/8 SWG

Earthing rod 20x2500 mm

GI wire no. 6 SWG/earth wire

Gauarding channel 100x50 mm 3.75 mtr. Long

GI wire No. 6 SWG

GI wire No. 8 SWG

MS Channel 100x50 mm for 11 KV

MS Channel 125x65x6 mm

Disc fitting B&S for ACSR weasal

11 KV polymer Pin with Nut

ACSR weasal conductor

Stone Pad 300x300x75 mm

PP & clamp SP-33 with nut & bolt

PP & clamp SP-55 with nut & bolt

Bracing clamp SP-33 with nut & bolt

Bracing clamp SP-55 with nut & bolt

Earth wire clamp SP-33 with nut & bolt

Earth wire clamp SP-55 with nut & bolt

E-clamp with nut & bolt

PG clamp for DOG conductor

PG Clamp for WEASEL conductor

F clamp with nut & bolt

Number plate with clamp, nut & bolt

Danger Board with clamp, nut & bolt

Barbed wire

Stay clamp with nut & bolt for SP-33

Stay clamp with nut & bolt for SP-55

Bolt & nut 200x12 mm/250x12 mm

Bolts & Nut 50x16 mm

Aluminium binding wire & tape (Single Pole)

PP & clamp with nut & bolt SP 55/33

PP clamp for SP-23/SP-33

Bracing clamp (top & bottom) for SP-23/SP-33

Earth wire clamp

Eye Bolt 190x16 mm with nut

LT shackle insulator

Clamp for LT insulator mid portion SP 55 STP

Description of Work / Item(s)

Amount

Painting of Single Pole (SP-33)

Painting of Double Pole (SP-33)

Painting of Tri Pole (SP-33)

Painting of Four Pole (SP-33)

Painting of Single Pole (SP-55)

Painting of Double Pole (SP-55)

Painting of Four Pole (SP-55)

Civil work CC 1:4:8

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Single pole SP-33)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Double pole SP-33)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Tri pole SP-33)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Four pole SP-33)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Single pole SP-55)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Double pole SP-55)

Erection of pole in mixed soil including mounting all accessories and excavation of pit (Four pole SP-55)

Erection of stay including excavation of mixed soil

Erection of earthing

Erection of stud stay

Erection of special bracket on STP as per drg

Stringing of 3Ph dog conductor & earthwire

Erection charges for gaurding

Fabrication of MS items

Shifting realianment of 11 KV SP,DP /LT line including dismentling,re-erection,re-stringing complete work

Revetment work for protection of pole

Excavation of earth in mixed soil

CC 1:4:8 Cement, Sand & Stone ballast

RR Masonary work in 1: 6 cement mortar

BIJENDRA KUMAR POKHRIYAL

MS SHYAM SINGH

NICHI MANUFACTURING PVT. LTD.

MS SHYAM SINGH

BIJENDRA KUMAR POKHRIYAL

NICHI MANUFACTURING PVT. LTD.

BIJENDRA KUMAR POKHRIYAL

NICHI MANUFACTURING PVT. LTD.

MS SHYAM SINGH

NICHI MANUFACTURING PVT. LTD.

MS SHYAM SINGH

PARTH POWER COMPANY

NICHI MANUFACTURING PVT. LTD.

BIJENDRA KUMAR POKHRIYAL

MS SHYAM SINGH

MS SHYAM SINGH

PARTH POWER COMPANY

NICHI MANUFACTURING PVT. LTD.

BIJENDRA KUMAR POKHRIYAL

MS SHYAM SINGH

NICHI MANUFACTURING PVT. LTD.