Development of infrastructure of Jamshedpur Co-operative Law College, Jamshedpur under Kolhan Univeristy, Chaibasa

Amount

EARTH WORK IN EXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earthwork in Hard soil as per specification and direction of E/I. (vide classification of soil item -B)

FILLING IN FOUNDATION TRENCHES AND PLINTH in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)

Providing designation 75-A, BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing designation 75-B, one BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and filling BRICK BATS in toilet sunken slab after waterproofing treatment of slab and beam sides including all taxes all complete.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work up to plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, BEAM

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, ROOF SLAB

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, LINTEL BAND

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, LINTEL

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, STAIRS

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum, CHAJJA

Providing, hosting and fixing above plinth level up to floor level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand ), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , exculuding the cost of reinforcement, with 1:1.5:3 (1cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20mm nominal size)

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including struting, propping etc. and removal of form for -

Foundation, footings, bases of columns etc.

Columns

ROOF SLAB

Beams, plinth beams, Lintels-

STAIRS (excluding landing)-

CHAJJA

Edges of slabs and breaks in floors and walls

Under 20 cm wide

Providing tor steel reinforcement TMT FE 500 of following dia. rods as per approved design and drawing including carriage of bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction and direction of E/I. (ONLY VALID FOR SAIL & TATA STEEL, JSPL, ELECTRO STEEL LTD. AND VIZAG STEEL)

TOR 8 MMDIA.

TOR 10 MMDIA.

TOR 12 -25 MM DIA.

TOR 28 -32 MM DIA.

Providing designation 75A brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing designation 75B brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing waterproofing material in cement conncrete work in doses by weight of cement as per manufacturer's specification.

Providing designation 75 A BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing 12 mm Thk. cement plaster(1:6) on inside walls with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 12 mm thick water proof CEMENT PLASTER (1:6) on outside wall with clean coarse sand of F.M.1.5 and waterproofing compound (as per specified and approved) including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. (Cost of waterproofing compound will be paid separately)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing & fixing FAN HOOK of 16 mm dia M.S. bar, 1 M long bent to required size and shape, placed in position and fluid in the R.C.C. slab-beam at the time of casting all complete as per building specification and direction of E/I.

Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I.

Making 6x6 / 20x6 mm grooves in plaster surface over walls trully horizontal or vertical as specified at regular intervals at all heights including cleaning finishing , scaffolding and curing with all leads and lifts of water all complete as per buildinng specification and direction of E/I.

Providing tuck pointing [1:3] in cement on brick work clean coarse sand of F.M 1.5 FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

2ND FLOOR -

3RD FLOOR -

Extra for PLASTER work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

2ND FLOOR -

3RD FLOOR -

TERRACE FLOOR-

FLOORING WORKS

Providing and laying DOUBLE CHARGE VITRIFIED FLOOR TILES in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.30 kg per sqm including grouting the joints with white cement and matching pigments etc. complete.

SIZE OF TILE- 600MMX600MM

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6 mm precast white GLAZED CERAMIC TILES in walls over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I

with commercial grade colour tiles.

Marble stone flooring with 18 mm th marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:

Udaipur Green Marble

Extra for pre finished nosing to treads of steps of marble stone

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 m

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels

Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.5 sqm -

Providing and laying vitrified Parking/Industrial tile in different sizes (thickness to be speified by the manufacture) with water absorption less than 0.08% and confirming to IS:4457:2007, of approved make in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg./ sqm.including grouting the joints with white cement and matching pigments etc. complete size of tile 300x300x10mm sizes all complete as per building specification and direction of E/I.

Extra for FLOORING work for each consecutive floor above first floor, all complete as per direction of E/I.

2ND FLOOR -

3RD FLOOR -

Providing and laying Matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. OVER OUTER WALL

DOORS & WINDOWS WORKS

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window ,sky light, fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative single leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative double leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Rectangular or square

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i. e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium window, ventilator shutters etc. with EPDM / Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

Providing and fixing glazing in aluminium door, shutters etc. with PVC/neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.0 mm thickness

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture I.S.:6315 marked, Hardwyn Make (Model 3000) or equivalent for doors including cost of cutting floors as required, embedding in floors & cover plates with brass pivot and single piece M.S. sheet outer box with side plate etc.complete as per the direction of E/I.

WITH STAINLESS STEEL COVER PLATE MINIMUM 1.25MM THICKNESS:-

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. (Approved brand - Godrej/ Dorset)

Providing and fixing aluminium round shape handle of outer dia.100 mm with SS screws etc. coplete as per direction of E/I.

Powder coated minimum thickness 50 micron aluminium.

Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing aluminium TOWER BOLTS ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required color or shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (over all area of door shutter to be measured).

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin- Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.”

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml”

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass (loee glass) of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. . The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Supplying, fitting & fixing local made COLLAPSIBLE GATE of approved size and make properly fabricated with vertical double channel 20 x 10 x 2 mm at 100 mm center and braced with M.S. flat diagonals 20 x 3 mm with top and bottom rail of T. iron 40 x 40 x 6 mm with 38 dia steel pulleys complete with bolt, buts locking arrangement, steppers, handles including applying a primer coat of read lead paint carriage, hoisting and taxes etc. all complete as per building specification and direction of Engineer Incharge.

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer

Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing sliding arrangement in racks/ cupboards/cabinets/ Window shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

WATER PROOFING TREATMENT

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roof terraces etc. consisting of following operations.

Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to IS : 2645 over the RCC slab including cleaning the surface before treatment.

Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 over 20 mm thick layer of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS: 2645.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand ) admixed with proprietary water proofing compund conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300X300 mm square.

The whole terrace so finished shall be flooded with water for minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the E/I.

With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying

a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI?212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm

Providing 12mm cement plaster(1:3) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm th. cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : (Approved Brand - MYK/Asian/ STP)

3 mm thick

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Covering of treated surface with PCC :- Providing 50mm thick Cement concrete M20 (1:1.5:3) maintaining slope in alternate 2mtX2mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with admixture of integral waterproofing and placing in position striking curing, taxes and royality all complete as per building specification and direction of E/i. Panels that has been left should be casted next day. There should be 6mm gap betwwen panels. Brand - Sika Plastocrete Plus, MYK proof WP, Fosroc-Conplast X4211 C,. Dr. Fixit Pidiproof LW+.(WORKS TO BE DONE BY REGISTERED APPLICATOR OF ABOVE MATERIALS WITH 10 YRS. GUARANTEE.)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface including preparing the plastered surface smooth with sand paper, soaping, curing and taxes all complete as per building specification and direction of E/I.

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives "Snowcryl - XT" of M/S Snowcem India Ltd, or equivalent of required shade.

New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/./10 sq.m.)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete.

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Providing two coats of SYNTHETIC ENAMEL PAINT of approved shade and make over new WOODEN surface including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I.

Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

MISCELLANEOUS WORK

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455X610mm and 45 mm deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber :

For 455x610 mm size

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and fixing C. I. Cover without frame for MANHOLE.

560MM DIA C.I. COVER (HEAVY DUTY) the weight of the cover to be not less than 108 kg

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910, on 12 mm dia steel bar confirming to IS: 1786, having minimum cross section as 23 mmX25mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protuded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in tank with 30X20X15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing plain multipurpose cement board (High pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

110mm diameter

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler - 110 mm

BEND - 110 MM

SHOE - 110MM

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge.

Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron)

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:8) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of ClassA category with properties of being termite/borer roof,water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 251.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In-Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Making Soak Pit 2.5 m diameter 3.0 meter deep with 45x45cm dry briick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standerd design .

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-35 grade with approved color design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

DT: Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH ring Machine all complete including supplying all meterial, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of engineer-in-charge. (Basic rates)

Drilling up to 30 mtr. Depth below G.L.

Supplying, assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen (RMS) pipes with ribs, confirming to IS: 12818, including hire and labour charges, fittings and accessories etc. all complete, for all depths, as per direction of engineer-in-charge.

100 mm nominal size dia. -

200/150 mm dia Deep borewell : Cost of drilling 200 mm X 165 mm X 125m deep brewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all all materials, tools drilling rig, Air compressure and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicle up to the site.

From 0.00 M to 50.00 M below G.L

From 51.00 M to 125.00 M below G.L

From 125.00 M to 200.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

200mm Nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run and nylon rope as required length shall be provided with each pump.

Submersible pump set 100mm dia (with polypropylene/ Noryl Impeller)

Supplying and fitting of standared make starter pannel board with arrangement of all necessory protection ,including all taxes , royalty etc all complete job as per direction of E/I 5 HP TO 10 HP

Supplying ,fitting & fixing & connecting 3 core 4 sqmm flat copper submerssible cable of Finolex / Hevels make including all taxes ,royalty etc all complete job as per direction of E/I

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I

Supplying,filling, spreading and levelling stone boulders of of size range 5cm to 20 cm, in recharge pit, in the required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Supplying,filling, spreading and levelling gravels of size range, 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads and lifts, all complete as per direction of E/I.

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

300 MM dia R.C.C. pipe

Supplying fitting and fixing Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm (2'-0"x2'-0"*2) in position as per specification and direction of E/I.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

CARRAIGE OF MATERIALS

LOCAL SAND , LEAD - 2P+1K= 3 KM.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

COARSE SAND , LEAD - 9P+1K= 10 KM.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

STONE CHIPS , LEAD - 21P+1K= 22 KM.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

BRICKS , LEAD- 7P+1K= 8 KM.

LANDSCAPING

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from local or other approved source including royalty and cariage up to 1 km. (Manure measured in stacks will be reduced 8% for payment). Screened through sieve of I.S. designation 4.75 mm.

Rough dressing the trenched ground including breaking clods.

Fine dressing the ground

Spreading of sludge, dump manureor / and good earth in required thivkness(Cost of sludge, dump manure or / and earth to be paid seperately).

Mixing earth and sludge or manure in proportion specified or directed.

In rows 5 cm apart in both direction

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis (varigated) of height 75-90 cm., multibranched in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Dreaceana pendanus, well developed, having 6 to 8 suckers with helthy foliage in 25 cm size Earthen pot /Plastic pot

Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot.

Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot / Plastic Pot.

Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. plant in 40 cm size Earthen Pot/ Plastic Pot

Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot.

Dracaena Mahatma having ht. 30 cm to 45 cm, well developed, fresh and healthy foliage in 20 cm size of Earthen pot / Plastic pot.

Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Foxtail Blue palm/ Fan palm of ht. 180-210 cm bottom girth 25-30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes joining of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)

External Work

25mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end )

25MM nominal bore

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Providing & fixing White River (Stone) Pables size of 2" to 2.5" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.

SANITARY WORKS

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled devicde (handle lever), conforming to IS:7231, parryware/Hindware/with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15mm nominal bore

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of 580X380X350mm without white PVC automatic flushing cistern, parryware/Hindware with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass with waste fitting as per IS : 2566 P.V.C. trap with outlet grating and other couplings in C.P. brass including parenting of fitting and cutting and making good the walls and floors wherever required..

Single half stall urinals with 5 litre P.V.C. auotmatic flushing cistern

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end )

32MM nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

25mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100mm dia. Steel Jali of approved quality.

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required:

kitchen sink without drain board

470x420mm bowel depth 178mm

Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality.

15 mm nominal bore with 45 cm length.

Providing And fixing PVC waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible Pipe

32mm dia.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (ITEM FOR RAIN WATER, SOIL, WASTE & VENT PIPES)

110 mm dia

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler -

Single pushfit Coupler

Single tee with door

Single tee without door

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 100mm outlet, with all complete.

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 75mm outlet, with all complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME)

Concealed work including cutting chases and making good the wall etc..

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)

Internal Work - Exposed on Wall

25 mm nominal dia Pipes

32 mm nominal dia Pipes

50 mm nominal dia Pipes

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455X610X mm and 45 mm deep for single pipe

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing C.P. brass Health Faucet (Telephonic shower with flexible pipe) including 450 mm long Braided Hoses with all fittings complete job. (Hand Shower - CAT. NO. - JAQUAR, ALD - 573/ Equivalent)

Providing and fixing C.P. Towel Ring (round) with flange. (Towel Ring - CAT. NO. - JAQUAR, AQN - 7721/ Equivalent)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

40MM DIA. -

ELECTRICAL WORKS

Point wiring in pvc conduit , with modular type switch:-Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Twin control point wiring in pvc conduit with modular type switch:- Wiring for Twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2way modular switch ,modular plate, suitable GI box etc. as required.

Power plug wiring in pvc conduit (2x4 sq mm):Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / sub main wiring in pvc conduit:Wiring for submain wiring with the following size of PVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:

2x1.5 sq.mm.+1x 1.5 sq mm(for toilet switch board +6A socket)

2x2.5 sq.mm.+1x 2.5 sq mm(for switch board )

2x6 sq.mm.+1x 6 sq mm( Sub-Mains DB's)

4 x 6 sq mm +2x6 sq.mm. (Sub-Mains DB's to Panel)

4 x 10 +2x6 sq.mm. (Sub-Mains DB's to Panel)

4 x 16 +2x6 sq.mm. (Sub-Mains DB's to Panel)

Wiring in existing conduit:-Supplying and drawing following sizes of PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit / PVC casing capping / as required.(Approved Brand - Havells/ KEI)

2x1.5 sq mm

3x2.5 sq mm (For (Lift)

4x6 sq mm(For Lift)

Supplying and fixing PVC conduit:-Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required . (Approved Brand - Havells/ KEI)

20 mm PVC coduit.

25 mm PVC coduit.

Supplying and fixing modular type switch / socket :-Supplying and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd. (Approved Brand - (Approved Brand - Havells/ L&T/ MK)

5/6 amps switch

15/16 amps one way switch

5/6 amps socket outlet

Telephone socket outlet

Supplying and fixing modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required. (Approved Brand - Havells/ L&T/ MK)

Supplying and fixing modular type blanking plate.:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (Approved Brand - Havells/ L&T/ MK)

Supplying and fixing modular boxes,base & cover plate:- supplying and fixing following size/ modules, GI boxSupplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required.

1 or 2 Module (78mmX78mmx45mm)

Supplying and fixing light plug point with modular type accessories :-Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs).

Supplying and fixing power plug point with modular type accessories :- Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs).

Supplying and fixing S.P. MCB DB :- Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board,240 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, interconnections powder painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

8 way double door

Supplying and fixing T.P MCB DB :- Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections,powder painted including earthing etc. as required. (but without MCB / RCCB /Isolator)

4 way(4+12)double door Horizontal type

6 way (4+18)double door Horizontal type

8 way (4+24)double door Horizontal type

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' catagory, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

6/32 amps.SPN

32 amps.TPN

40 amps.TPN

63 amps. TPN

Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (8 + 24 ), Double door, Vertical type

32 amps.TP

63 amps.TP

Supplying and fixing following rating and breaking capacity MCCB thermomagenatic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel,connections etc as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C"curve including connections, painting etc. as required.

Supplying and drawing following pair 0.5 sq mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed PVC conduit as required,

CABLE & CABLLE TRAY

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required.

Above 35 sq mm and upto 95 sq mm (clamped with 20mmx3mmGI tape)

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding185 sq mm but not exceeding 400 sq mm Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 185 sq mm but not exceeding 400 sq mm Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Supply of PVC/ XLPE Insulated PVC sheathed heavy duty armoured electric cable with alluminium conductor for working voltage upto and including 1100 volts (conforms to IS:1554,part-1)

50 sq mm x 3.5 core

95 sq mm x 3.5 core

300 sq mm x 3.5 core

6 sq mm x 2 core

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 50 sq. mm (35mm)

3½ X 95 sq. mm (45mm)

3½ X 300 sq. mm (70mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5% , in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required.

300 mm width X 50 mm depth X 1.6 mm thickness

MAIN DISTRIBUTION BOARDS / L.T. PANEL.

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

630 Amp, MCCB FP -1no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 1 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 800 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

a)160 Amp, MCCB FP -5 no

LT Panel (Normal) as above ( L.G.F) - 1 SET

630A MCCB FP

160A MCCB FP

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 500/5 IS 2705 part 3

50MM*5MM(2.30 KG/MTR) copper strip

25MM*5MM(1.15 KG/MTR) copperStrip

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

Supplying and fixing wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

630 Amp, MCCB FP -1no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 1 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 800 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

a)160 Amp, MCCB FP -5 no

b)25/100 Amp, MCCB FP -4 no

d)6/32 amps.SPN-2no

d)6/32 amps.TPN-2no

e)40 amps.TPN-3no

f)63 amps. TPN-4no

LT Panel (Normal) as above ( L.G.F) - 1 SET

630A MCCB FP

160A MCCB FP

25/100 A, MCCB FP

6/32 amps.SPN

6/32 amps.TPN

40 amps.TPN

63 amps. TPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 500/5 IS 2705 part 3

50MM*5MM(2.30 KG/MTR)copper strip

25MM*5MM(1.15 KG/MTR)copperStrip

10 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

6 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

Supplying and fixing wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

LT FLOOR PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

25/100 Amp, MCCB FP -2no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 2 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 200 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

a) 32A MCB TPN-2 no.

b) 50/63A MCB TPN-3 no.

LT Panel (Normal) as above ( Floor Panel) - 4 SET

25/100 A, MCCB FP

6/32 amps.MCB TPN

50/63 amps. MCB TPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 100/5 IS 2705 part 3

25MM*5MM(1.15 KG/MTR)copperStrip

10 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

6 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

Supplying and fixing wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

LT FLOOR PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

160 Amp, MCCB FP -2no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 2 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 200 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

a) 50/63A MCB TPN-3 no.

b) 100A MCCB TPN-1 no.

LT Panel (Normal) as above ( Floor Panel) - 4 SET

160 A, MCCB FP

25-100 A, MCCB FP

50/63 amps. MCB TPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 100/5 IS 2705 part 3

25MM*5MM(1.15 KG/MTR)copperStrip

10 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

Supplying and fixing wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

EARTHING & LIGHTNING CONDUCTOR.

80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Length and backfill compound chemical 4 bag (per bag 25Kg)

Providing and fixing 8 SWG copper wire (4.0 mm dia)(0.1185kg/mtr).

P/F of lighting conductor finial, made of 25mm. Dia. 300mm. Long copper base plate including holes etc. complete as required.

Rivetting, sweating and soldering of copper/GI tape (with another copper/GI tape base of the finial or any other metallic object) as required.

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for horizontal run)

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for vertical run)

SUPPLY OF LIGHTING FIXTURES & FANS

Supplying, Installation, Testing & Commissioning of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required, (Approved Brand - Havells/ Wipro/ Crompton)

20/22w LED tube light

Supplying, Installation, Testing & Commissioning of following rating recess/ surfface mounted LED round /square shape down light luminaierewith pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required. (Approved Brand - Havells/ Wipro/ Crompton)

18/20w LED round down light.

2"x2"LED panel light

Supplying, Installation, Testing & Commissioning of following rating LED street light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required. (Approved Brand - Havells/ Wipro/ Crompton)

120W LED street light.

Supplying, Installation, Testing & Commissioning of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required.

1200mm (48") BLDC 5 star rating 32w Ceiling fan, (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

1400mm (48")BLDC 5 star rating 32w Ceiling fan. (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

Supplying of 9" (230) mm )metal exaust fan. (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

Supplying of 12" (300) mm )metal exaust fan. (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

Supplying of 16" Wall mounted fan. (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

Providing of bulkhead fitting with 9/10w LED bulb. (Approved Brand - (Approved Brand - Havells/ Bajaj/ Crompton)

ERECTION OF LIGHTING FIXTURES ,FANS

Supplying and fixing 2 pin 5A ceiling rose on the existing junction box wooden block including connection etc ,as required.

Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

D.G. SET

Silent type D.G Set of capacity 200 KVA With AMF Panel IS/IEC-600341 IS: 1460 IS: 13018, (Approved Brand - Cummins/ Kriloskar/ Mahindra)

EARTHING

80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Length and backfill compound chemical 4 bag (per bag 25Kg)

Providing and fixing 8 SWG copper wire (4.0 mm dia) (0.1185kg/mtr).

MV cable laying upto 35 sq mm .in ground:- Laying of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1kv grade of size exceeding 35 sq mm direct in ground including excavation and cushioning ,protective covering and refilling the trench etc as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required Upto 35 sq. mm (clamped with 1mm thick saddle)

FIRE FIGHTING WORKS

(A) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered with anti vibration pads.

2850 lpm at 88m Head

(A) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (B) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (D) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.

2850 lpm at 88m Head

(A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads

180 lpm at 88 m Head

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads.

900 lpm at 35 m head

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3.5 × 50 sq.mm.(aluminium)

4 × 10 sq.mm.(aluminium)

2 × 2.5 sq.mm.(Copper) to be laied in 5 pairs for engine

2 × 1.5 sq.mm. in Conduit

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

200 mm diameter

150 mm diameter

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

65 mm diameter

80 mm diameter

100 mm diameter

150 mm diameter

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

80 mm diameter

100 mm diameter

150 mm diameter

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

200 mm diameter

100 mm diameter

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

200 mm diameter (WALL THICKNESS = 6.3 mm)

150 mm diameter

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

25 mm diameter

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single Headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required

Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Gun Metal

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required:

4 WAY-100 MM DIA. M.s. PIPE

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as required

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 6 inches dia, 2 watts, 70/100 volts ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

SLIT AC

Supplying, installations, testing and commissioning 1.5 TR Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas/ Toshiba.

Supplying, installations, testing and commissioning 2.0 TR Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas Toshiba..

Providing and placing Copper tube of size 1/4"for split ac unit 1/1.5/2/3 TR capacity including nitride rubber insulation.

Supplying and placing Copper tube of size 1/2" for split ac unit 1/1.5/2/3 TR capacity including nitride rubber insulation.

Supplying and installing 5 KVA wall mounted automatic voltage stablizer from range 140v to 280v .

Supplying and Fixing of Drain pipe for AC as per required size, all complete.

Supplying and Fixing prefabricated, painted M.S. Outdoor stand for 1/ 1.5 TR split AC with all complete.

Supplying and Fixing prefabricated, painted M.S. Outdoor stand for 2 TR split AC with all complete.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing, Supplying and installing Potable water purification system with inbuilt water cooler RO system with stainless steel (304G) 120 ltrs water storage capacty & 2 tap, fully automatic, including all complete. (Brand Blue Star (NST80120B)/ Equivalent)

Providing and fixing C.P. brass concealed Stop valve of standard design and of approved make conforming to IS:8931. - 20 mm nominal bore. (Approved brand - ESCO/ Jaquar/ Equivalent)

TRANSFORMER & DG SET . Supplying, Installation, Testing & Commissioning . Outdoor type copper wound Transformer continuosly rated for 3ph 50Hz at full load and temp.rise not exceeding 450 c by thermometer in oil and 500c by the resistance in winding after continuous run at full load rating ,the transformer should have oil unmersed winding having vactor group DY11 HT side connected in delta and LT sideconnected in star with neutral brought out connected to provide separate earthing .The transformer shall have power terminal arrangenent bushing / cable end box on HT side and cable end box on LT side 2 nos channels with stoppers shall be provided and fix on the provided plinth for mounting the transformer .The transformer should have following standard fitting.Transformer shall be latest manufacturing standards as per amended IS specification and the load & No load losses shall be limited to the values given below or as per IS 2026 or norms issued by SEB which ever are lower. (Approved Brand - Aarnav Powertech/ Equivalent)

Oil conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel

oil drain valve

Lifting eyes / hooks

Two earthing terminals

Digram and rating plate

Air vent

Explosion vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain rollar

Power transformer 11000/433V with off load tap changer -12.5% to +2.5% in steps of 2.5% per BIS leveel-2

400KVA (No load loss 500w and load loss 3000w)

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Terrace Pump

Providing, supplying and installing Pressure Gauge Assemble with Gate/Ball Valve including all accessories, complete job.

Providing, supplying and installing Air release Valve / Drain Valve as per drawing all complete.

Supplying and Fabrication MS Structure for support for piping as per required with primer and 2 coats of enamel painting.

Providing and fixing 25 / 15 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

SURVEILLANCE (CCTV)

Supply, installation , testing & commissioning of NVR 32 Channel: Connect Up to 32 IP Cameras, Up to 8 Megapixels Resolution, HDMI output with 4k output and VGA output with 2MP Output , Support H.265,H.264, MJPEG, Incoming Bandwidth 256 Mbps, 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD upto 6TB, 2 USB at least 1 × USB with 3.0, Serial interface:1 RS-485, 1 RS-232, Alarm I/O 16/4, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified, (Approved Brand - HICKVISION, DS-7732NI-k4/ Equivalent)

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Dome Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8mm Fixed lens, 0.028 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Edge Anlalytics- Line crossing detection, Intrusion detection, Inbuilt Audio Motion detection, Scene change detection, video tampering, UL, CE, FCC certified. (Approved Brand - HICKVISION, DS-2CD3121G0-IUF/ Equivalent)

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Bullet Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, inbuilt audio Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. (Approved Brand - HICKVISION, DS-2CD3021G0-IUF/ Equivalent)

Supply, installation, testing and commissioning of outdoor 2MP, VF LENS , 2.8MM TO 12MM, resolution 1920*1080 fixed lens Color Indoor AV Camera, 1/3" CMOS, H.264/MJPEG High-profile, dual Stream support, True Day & Night (TDN) with , Wide Dynamic Range (WDR), Open Network Video Interface Forum (ONVIF) Profile S & G - TF card support (128 GB), IP66 & IK 10 Rating, Power Over Ethernet (POE), IR distance upto 30 Meter. (Approved Brand - HICKVISION, DS-2CD3021G0-IUF/ Equivalent)

Supply, installation , testing & commissioning of POE switch of 10/100/1000 Mbps on each Ethernet port. The switch shall be mounted on rack. The rate shall also include cost of power supply and providing end termination.

24 port 10/100/1000 Mbps managed Giga Byte POE Switch. (Approved Brand - One Touch, OT-1724P/ Equivalent)

16 port 10/100/1000 Mbps managed Giga Byte POE Switch. (Approved Brand - One Touch,OT-1716P/ Equivalent)

HDMI Splitter” is a unit whereby you can send your HDMI output of set-top boxes, DVD Players, D-VHS Players, PC's and other HDTV devices. (Approved Brand - Mile Stone,ML 401 HMVS/ Equivalent)

Supply, drawing and connecting of cat-6, UTP cable with conduit for cctv. (Approved Brand - D-LINK/ Polycab,NCB-C6UGRYR-100)

Supply , Fixing of 6U Racks for POE switch installation in floor wise. (Approved Brand - D-LINK/ Equivalent,NWR-6U-5550-GR)

Supply , Fixing, Commissioining of 50 Inch Monitor for CCTV. (Approved Brand - SONY/LG/ SAMSUNG)

Supply , Fixing, Commissioining of HDMI cables for connecting monitor to NVR. (Approved Brand - 4K/ EQUIVALENT)

Supply , Fixing, Commissioining necessary accessories for cctv , nvr and monitors, etc. all complete.

FURNITURE

LOW HEIGHT STORAGE, PROVIDING & SUPPLING PLACING POSITION OF MODULAR BACK UNIT TOP SHALL BE MADE FROM 18 MM THICK PRELAMINATED PARTICLE BOARD OF GRADE II TYPE III OF IS 12823/LATEST. * WHILE REST OF THE SIDES AS WELL AS SHELVES AND SHUTTER TO BE MADE UP OF 18 MM THICK PRELAMINATED PARTICLE BOARD. MACHINE PRESSED EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE FIXED DULY PASTED WITH THE ASSISTANCE OF EDGE BANDING MACHINE AT 200 DEGREE CELSIUS. * STORAGE UNIT WITH 3 DRAWERS + 2 SHUTTERS CONSTRUCTION IS 1 OPENABLE DOORS WITH 1 FIXED SHELVE PER CARCASS LENGTH IS @ 400 MM + 2 OPENABLE DOOR WITH 1 FIXED SHELVE PER CARCASS LENGTH IS @ 400 MM + 3 DRAWERS , 2 EQUAL DRAWERS HEIGHT IS @ 130 MM & 1 FILLING DRAWER HEIGHT IS @ 406 MM , IN PROVIDED WITH 1 UNIVERSAL CAM LOCK + 1 CENTRAL LOCK FOR DRAWERS FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. OVER ALL HEIGHT OF PRODUCT IS @ 750 MM .* EACH SHUTTER SHOULD BE FIXED WITH REQUIRED NUMBERS HINGES, SS TOWER BOLT OF 100 X 10, DOUBLE STRIP MAGNETIC CATCHER AND DRAWERS SHALL HAVE 100 MM SIZE SS FANCY HANDLES (ONE ON EACH DRAWER) WITH NECESSARY HARDWARE/ FITTING/ HINGES ETC. OF APPROVED QUALITY(MAKE: EBCO).FOR INSTALLATION OF SIDE UNIT WOODEN DOWELS AND MINIFIX TO USE FOR ADDITIONAL SUPPORT * THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

CHAIR FOR COMMON ROOM & LIBRARY * SUPPLYING & PROVIDING CAFETERIA CHAIR SIZE IS 381MM(L)X 419MM(D)X 839MM(H) A COMBINATION OF SYNTHETIC FIBER WITH STAINLESS STEEL MAKE THE PRODUCTS UTILE AND A DELIGHT, THE COMPLETE STRUCTURE SHALL BE MADE UP OF 20% GLASS FILLED BLOW MOLDED HIGH-DENSITY POLYETHYLENE ANDIS,THE FRAME STRUCTURE SHALL BE SUPPORTED BY ( 2 STRAIGHT + 2 SLANT ) FOUR LEGS.THE TUBULAR WELDED FRAME IS MADE FROM DIA2.22 +/- 0.03CMX 0.12+/- 0.0128 CM AND 3.5+/- 0.03 CM X 0.12+/- 0.0128 AM STAINLESS STEEL 202 GRADE TUBE & THE TUBE ARE BUFF POLISHED TO GIVE SHINY FINISH.SEAT AND IN BACK GIVEN HANDLE TO HOLD ARE MADE OF INJECTION MOULDED HIGH IMPACT STRENGTH POLYPROPYLENE POLYMER COMPOUND WITH INDOOR GRADE UV RESISTANCE AND PRESSED FITTED WITH LEGS.THE CHAIR IS EASY TO STORE WHEN NOT IN USE, SINCE YOU CAN STACK UP TO 6 CHAIRS ON TOP OF EACH OTHER. * THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

2 SEATER SOFA * SUPPLYING AND PLACING TWO SEATER EXCLUSIVE PREMIUM LEATHERETTE MODERNIST CLASSIC DESIGN LOUNGE SEATING SOFA SIZE IS 1410MM(L) X890MM(D)X 870MM(H) WITH KILN-DRIED WOOD FRAMING MAKES IT WARP AND SCRATCH RESISTANT,COMFORTABLE SEAT DEPTH & HEIGHT DESIGNED KEEPING MODERN INDIAN LIFESTYLE IN MIND,WRAPPED IN BUTTERY-SOFT PREMIUM LEATHERETTE, THE PANELLED BACK AND CUSHIONED ARMRESTS ENCOURAGE LOUNGING,DESIGNED WITH MODERNITY & ELEGANCE, CHOOSE THE OPTION THAT SUITS YOUR HOME. * COMBINATION CONSTRUCTION STRUCTURE ARE MADE IN MOISTURE CONTENT SHALL BE LESS THAN (10-12)%. THICKNESS OF PLYWOOD USED (MM) SHALL BE 12 MM GRADE IS 303 INDIAN STANDARD FOR COMMERCIAL (COMMON) AND MOISTURE PROOF PLYWOOD (TENTATIVE).UNDERSTRUCTURE FRAME SHALL BE CONSTRUCTED FROM 18 MM THICK KILN-DRIED GERMAN BEECH WOOD FRAMING IS HIGHLY DURABLE. THE COMPLETE STRUCTURE SHALL BE COVERED BY P.U.FOAM FIXED WITH ADHESIVE GLUE ,THE FRAME SHALL BE PADDED WITH HIGH RESILIENCE POLYURETHANE FOAM HAVING 28 +/- 5 DENSITY IN SEAT IT SHALL BE STACK FOAM OF 50MM THIK,40MM THICK BACK FOAM HAVING 20 +/- 5 DENSITY FOAM USED ,THERE SHALL BE CUSHION ARM 40MM THICK PROVIDED PADDED WITH HIGH RESILIENCE POLYURETHANE FOAM HAVING DENSITY 20 +/- 5. THE COMPLETE STACK FOAM STRUCTURE SHALL BE COVERED WITH PREMIUM LEATHERETTE IN BLACK-EERIE BLACK-COFFEE BROWN,BROWN-BURNT UMBER COLOUR, IT COMPLEMENTS THE MODISH LEGS ARE MADE BY ROUND SHAPE IN PVC MATERIAL. ( SEAT : 510 MM(D) X 445MM(H) , ARMS HEIGHT @ 620MM / BACK HEIGHT @ 460MM ) * THE SELLER / COMPANY SHOULD BE ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, ISO 45001:2018 CERTIFICATES OF THE MANUFACTURER CERTIFIED BY NATIONAL ACCREDITATION BOARD OF CERTIFYING BODIES, IGBC, SEDEX, GREEN PRO, AIOTA, INDIAN DESIGN MARK , FSC CERTIFICATE. THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

CENTER TABLE Supplying and placing of Center Table,Material & Subtype Solid Wood - Beech Wood Frame Material-Solid Wood. Leg Material Solid Wood. Finish-Matte Colour & Colour Family Brown - Walnut, 10mm glass on top & wooden in sides Dimension-(W)1130mm X (D)630mm X (H)410mm,The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKE ..WARRANTY 5YEARS.MODEL NO-HOPPER/CT** THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

REGULAR OFFICE TABLE WITH SIDE UNIT OFFICE DESK DESK STRUCTURE OF L SHAPED DESK . PRIMARY WORK SURFACE OVER ALL SIZE IS 1500MM(L)X 600MM(D)X 750MM(H) 25MM THICK TABLE TOP MADE OF PRELAMINATED PARTICLE BOARD WORK SURFACE WITH THE EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE WITH THE HOT MELT GLUE . MODESTY PANNEL 18MADE OF MM THICK . *PROVISION OF SIDE UNIT OF SIZE IS 900MM(L)X 450MM(D)X 750MM(H) ,(COMBINATION CONSTRUCTION WIRE MANAGEMENT HOLE WITH PVC GROOMENT ON TABLE TOP, LEFT SIDE TABLE TOP BASED ON A 18MM THICK SIDE PANNEL ENGINEERED WOOD & FROM RIGHT SIDE UNIT HAVE 2 SLIDING DOOR + 1 FIXED SHELVE . *SIDE UNIT SIZE 900MM(L)X 450MM(D)X 750MM(H), IN PROVIDED WITH LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. OVERALL CONSTRUCTION OF SIDE UNIT IS 18MM THICK ALONG WITH FECIA OF SLIDDING SHUTTERS. *THREE LAYER PRELAMINATED PARTICLES BOARD(WOOD PRODUCT) OF GRADE II TYPE III OF IS 12823/LATEST ,* THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

OFFICE CHAIR * MEDIUM BACK 360° DEGRE REVOLVING CHAIR SKU : 70008/MB/STANDARD , * ALL OVER SIZE IS : 580MM(L)X 670MM(D)X 1110MM(H) , *THE CHAIR MADE OF FULL UPHOLSTERY IN BLACK COLOUR . IT WILL COMES IN MATTE FINSIH IN CONTEMPORARY STYLE . DETAILS : * ARMS : AMREST IS HAVING TWO ADJUSTMENT HEIGHTS (UP & DOWN) . * USE OF PLY: 12 MM THICK HOT PRESSED BWR PLYWOOD (IS GRADE - 303 FOR SEAT AND BACK) . * SEAT: 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN SEAT , * BACK : 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN BACK . BACKREST SUPPORT FOAM DESIGN BASED ON SYMMETRICAL LUMBAR SUPPORT * MECHANISM : SINGLE LOCKING MECHANISM . SEAT MAXIMUM HEIGHT IS 580MM & MINIMUM HEIGHT IS 480MM & BACK HEIGHT FROM FLOOR MAXIMUM HEIGHT IS 1110MM & MINIMUM HEIGHT IS 1010MM * GAS LIFT 100 MM TELESCOPIC HAUDRAULIC * BASE : 650MM NYLON BASE WITH SMOOTH CASTORS .* THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

CHAIRS FOR COMPUTERS * MID BACK 360° DEGRE REVOLVING CHAIR SKU : 70020/LB, * ALL OVER SIZE IS : 625MM(L)X 450MM(D)X 920MM(H) , *THE CHAIR MADE OF FULL MESH IN BLACK COLOUR . IT WILL COMES IN MATTE FINSIH IN CONTEMPORARY STYLE . DETAILS : * ARMS : FIXED PP ARMREST . * USE OF PLY: 12 MM THICK HOT PRESSED BWR PLYWOOD (IS GRADE - 303 FOR SEAT). * SEAT: 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN SEAT , * BACK : FRAME OF DESIGN SHALL BE CURVED MADE OF TWO PIECES INJECTION MOULDED FRAME COVER WITH MESH .BACKREST SUPPORT MESH DESIGN BASED ON SYMMETRICAL LUMBAR SUPPORT * MECHANISM : SYNCRO SINGLE LOCKING MECHANISM . * ONLY SEAT SIZE IS 445MM(L)X 450MM(D)X 520-425MM(H) & THE BACK SIZE IS 625MM(L)X 480MM(H) , SEAT MAXIMUM HEIGHT IS 520MM & MINIMUM HEIGHT IS 425MM & BACK HEIGHT FROM FLOOR MAXIMUM HEIGHT IS 920MM & MINIMUM HEIGHT IS 820MM . * GAS LIFT 100 MM TELESCOPIC HAUDRAULIC * BASE : 650MM NYLON BASE WITH SMOOTH CASTORS,* THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

VISITORS CHAIR, SEMINAR HALL AND CHAIR FOR LIBRARY READING TABLE ANJIS/32002 : FIX MULTI PURPOUSE LEATHERETTE CHAIR IN BLACK COLOUR WITH MATTE FINISH SPECIFICATION : DURIAN - - OFFICE SEATING - - ANJIS/32002 CHAIR , TYPE : * FIX CANTILEVER , * ALL OVER SIZE IS : 595MM(L)X 510MM(D)X 875MM(H) , *THE CHAIR MADE OF FULL LEATHERETTE IN BLACK COLOUR . IT WILL COMES IN MATTE FINSIH IN CONTEMPORARY STYLE . DETAILS : * ARMS : PADDED ARMREST. * USE OF PLY: 12 MM THICK HOT PRESSED BWR PLYWOOD (IS GRADE - 303 FOR SEAT AND BACK) . * SEAT: 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN SEAT , * BACK : 40 ± 2 MM THICK POLYURETHANE FOAM WITH DENSITY 32 (±3) KG PER CU METER FOR BEST QUALITY CUSHIONING IN BACK . BACKREST SUPPORT FOAM DESIGN BASED ON SYMMETRICAL LUMBAR SUPPORT * ONLY SEAT SIZE IS 500MM(L)X 510MM(D)X 455 MM(H) & THE BACK SIZE IS 440MM(L)X 595MM(H) , BACK HEIGHT IS @ 440MM . * BASE : 4 LEGS METAL POWDER COATED * THE PRODUCT BY THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

MULTIPURPOSE TABLE TABLE SIZE : (W)1800MM X (D)1050MM X (H)750MM MADE OF 25MM THICK PRELAM PARTICLE BOARD TABLETOP SUPPORTED WITH POWDER COATED "C" SHAPE METAL LEGS OF SIZE 50MM X 50MM AND CONNECTORS OF SIZE 40MM X 40MM. PROVIDING 0.8MM THK MS POWDER COATED CRCA SHEET PERFORATED MODESTY PANEL AT FRONT SIDE, BELOW TOP. IN BROWN-CLASSIC WALNUT COLOR WITH MAIN TABLE SIZE 1800MM(L) X 1050MM(D) X 750MM(H). Table which without wire manager.THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

WORKSTATION PRIMARY WORK SURFACE OVER ALL SIZE IS 1200MM(L)X 600MM(D)X 750MM(H) 25MM THICK TABLE TOP MADE OF 25MM THICK PRELAMINATED PARTICLE BOARD WORK SURFACE WITH THE EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE WITH THE HOT MELT GLUE . MODESTY PANNEL MADE OF 18MM THICK, WIRE MANAGEMENT HOLE WITH PVC GROOMENT ON TABLE TOP. *CONSTRUCTION RIGHT SIDE OF TABLE TOP IS BASED ON A FIXED PEDESTAL 3 DRAWERS & FROM LEFT SIDE OF TABLE TOP IS BASED ON 18MM THK ENGINEERED WOOD PVC EDGE BANDING PEDESTAL BACK,TOP,BOTTOM & DRAWERS ARE MADE OF 18MM THICK WITH 1 CPU TROLLY MADE IN BLACK METAL POWDER COATED. *FIXED PEDESTAL:L:410MM(L)X 580MM(D)X 750MM(H) ,IN PROVIDED WITH CETNRAL LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. OVERALL CONSTRUCTION OF PEDESTAL IS 18 MM ALONG WITH FECIA OF DRAWERS. THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

ALMIRAH, METAL STORAGE OF SIZE 900MM(L)X 450MM(D)X 1980MM(H) BODY MADE OUT IN 22 GAGUE(0.8MM) & DOOR 19 GAGUE(1 MM) CRCA SHEET. 4 ADJUSTABLE SHELVE IN 22 GAGUE(0.8MM) & PEDESTAL 18 GAGUE 1.2 MM CRCA SHEET. HAVING FOUR SHELVES MAKING FIVE COMPARTMENT, UNIFORMLY DISTRIBUTED LOAD CAPACITY OF EACH SHELF SHALL BE 60 KG MAXIMUM,FITTED WITH MS BODY LOCK & HANDLE. FINISHING WITH EPOXY POLYESTER POWDER COATED TO THE THICKNESS 50-60 MICRONS(+/-5 MICRON) IN COLOR GREY-LIGHT GREY (GARNER) (Approved Brand - Durian/ Godrej/ Featherlite)

LECTURE HALL DESK (3 SITTING) delite hi-tech THREE SEATER Class Room Desking / Seating INTEGRATED DESK CUM SEATING with MS support as per company design, size - Front 1800(W)x450(D)x750mm (H), Middle - 1800(W)x850(D)x750mm (H), Last -1800(W)x650(D)x750mm (H) (Brand - delite hi-tech (DAS-8509)/ Durian)

BAGGAGE RACK DURIAN GALVIN/2000 SLOTED ANGLE RACK OF SIZE 900MM(L)X 450MM(D)X 2000MM(H) SLOTTED ANGLE RACK -CLSOED FROM TWO SIDE 7 SHELVES INCLUDING TOP & BOTTOM ANGLES : 40MM X 40MM X 2MM(THICK) S.S. 202 G SHELF : 36X15X1MM S.S. . (Approved Brand - Durian/ Godrej/ Featherlite)

READING TABLE (LIBRARY) * SUPPLYING AND PLACING OF NON SHARING SINGLE SEATER WORKSTATION OF 65MM THK SLIDING TILE BASE PARTITION OF 1200MM HEIGHT, PROVIDING AND SUPPLYING NON-SHARING SINGLE UNIT WORKSTATION TABLE IN COMPLETELY KNOCK DOWN CONDITIONS WITH AN OVERALL SIZE 1200MM X 600MM X 1200MM THAT IS TO BE ASSEMBLED AT SITE. THE WORK TOP SHALL HAVE THE SIZE 1184MM X 592MM MADE UP OF 25MM THICK PRE- LAMINATED PARTICLE BOARD OF GRADE II TYPE III OF IS 12823/LATEST . OF IS LEVEL WITH APPROVED LAMINATE AND FINISH AS PER APPROVED SHADE. * THE PROFILE OF THE TOP SHALL BE IN RECTANGLE SHAPE AND THE EDGES SHALL BE SEALED WITH 2MM THICK THIN STRIP OF IMPERMEABLE PVC THAT IS CUT TO FIT THE SIZE OF BOARD PANEL AND DULY PASTED WITH THE ASSISTANCE OF EDGE BANDING MACHINE AT 200 DEGREE CELSIUS. * THE TOP TRIM, TOP BAR, MID BAR, VERTICAL BAR, RACEWAY, SKIRTING SHALL BE MADE UP OF ALUMINIUM EXTRUSIONS (PRE-TREATED) AND DULY POWDER COATED WITH POLYESTER POWDER COATING 40P-60P THICK . THE TRIMS SHALL HAVE THE SIZE 67MM X 19MM WITH 1.5MM THICK COVERED WITH DIE CAST END CAPS ON JOINTS 2 WAYS, 3 WAYS & 4 WAYS (L-COVER FOR CORNER, T-COVER FOR MIDDLE SECTION WHEREVER REQUIRED). THE ALUMINIUM RACEWAY SHALL BE SITUATED BELOW THE WORKTOP WITH AN OVERALL SIZE 116MM(H) X 60MM(D) WITH 1.4 MM COVER THICKNESS AND 2MM BACK THICKNESS AS PER REQUIREMENT OF INLAYING THE ELECTRICAL MANAGEMENT AND CARRYING THE WIRE HORIZONTALLY. *THE EXPOSED VERTICAL AND HORIZONTAL FACES OF THE FRAMES SHALL BE SNAP FITTED WITH TRIMS. THERE SHALL BE SOFT-BOARD (WITH FABRIC) AND MARKER BOARD PROVIDED AT FRONT OF THE USER. LAMINATED TOP TILE AND BOTTOM TILE SHALL BE SITUATED AT BOTH SIDES OF THE USER AND BELOW THE WORK TOP RESPECTIVELY. THE PARTITION SHALL HAVE CONCEALED WIRE MANAGEMENT CAPABILITIES AND SHOULD BE ENGAGED FOR RESPONSIVE AND SAFE OPERATIONS OF POWER, TELECOMMUNICATIONS AND DATA (LAN) AND HAS SEPARATE COMPONENTS FOR ELECTRICAL, DATA AND TELEPHONE CABLES HAVING ADEQUATE CAPABILITY OF BOTH THE VERTICAL AND HORIZONTAL WIRE MOVEMENTS. SLOTS/CUT-OUTS SHOULD BE GIVEN ON RACEWAYS TO FIX ALL ELECTRICAL AND DATA POINTS. SINGLE SIDED PVC WIRE MANAGER SHOULD BE ENCLOSED AT TABLE TOP.ADJUSTABLE LEVELLER SHOE SHALL BE PROVIDED AT BOTTOM OF THE PARTITION TO AVOID SCRATCHES ON THE FLOOR.PARTICLE BOARD OF GRADE II OF IS LEVEL. THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

NOTICE BOARD Supply, Installation and Placement of Display Board : Size 6'X4' Purpose of board-Display board, Surface Material-Woollen felt / fabric in various colours covered with aluminium framed 2 mm clear acrylic sheet lockable (+- 1 mm Tolerance), Core material (+- 2 mm Tolerance)- 9 mm thick soft board, Backing Material-Laminate sheet with extra melamine surface mix colour OR Galvanised steel sheet, Aluminium frame-Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285-2002 - Width of Aluminium Frame = 16mm thickness +- 3 mm tolerance,THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

PODIUM DURIAN Wooden Podium SIZE: (L)550MM X (W)550MM X (H)1200MM WOODEN PODIUM MADE WITH 18 MM THICK BOTH SIDE PRELAMINATED PARTICALE BOARD-THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG".

CLASSROOM DESK PROVIDING & SUPPLYING FIXING OF CLASSROOM THREE SEATER COLLEGE DESK WITH SHELF/STORAGE UNDER DESK WHICH ONE MADE BY CAST IRON,DESK TOP MADE BY 18MM THICK PRELAMINATED PARTICAL BOARD OF GRADE II TYPE III OF IS 12823/LATEST,TWO SEATER CLASSROOM DESK CUM BENCH, TOTAL SIZE OF BENCH : 1500MM(L)X 950MM(D)X 760MM(H) DESK SIZE :- 1500MM (W) X 400MM (D) X 760MM (H) BENCH SIZE :- 1500MM (W) X 310MM (D) X 390 / 760MM (H) BACK SIZE :- 1500MM (W) X 150 MM (H), UNDER STRUCTURE-BLACK 9005 ERW PIPE (AS PER IS:7138) : 25X25X1.2MM MS ROUND PIPE, OF THICKNESS 1.2MM IN BLACK EPOXY POLYESTER POWDER COATED TO THE THICKNESS 50-60 MICRONS(+/-5 MICRON) AT BASE WITH PLASTIC CAPS MADE OF PP COPOLYMER (3530 GRADE) ARE ALSO PROVIDED ON THE REAR FRAMES ADDING MORE AESTHETIC VALUE TO THE PRODUCT. * ADDITIONAL HORIZONTAL SUPPORTS OF M.S. C SECTIONS OF 1.2MM THICK ARE PROVIDED BELOW THE DESK & SEAT.SHELF: 0.8MM THICK POWDER COATED M.S. SHEET BELOW THE DESK & HOOKS ON EITHER SIDE OF DESK IN M.S. ROD OF DIA 6MM.TOP,SEAT AND BACK PANEL: 18MM THICK PRE LAMINATED BOARD WITH MACHINE PRESSED EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE FIXED DULY PASTED WITH THE ASSISTANCE OF EDGE BANDING MACHINE AT 200 DEGREE CELSIUS.THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

WAITING CHAIR * SUPPLYING AND PLACING IN POSITION OF A MILD STEEL VISITOR BENCH OF SIZE IS 1820MM(L)X 690MM(D)X 790MM(H). THE COMPLETE MILD STEEL BENCH HAS SEAT & BACK SINGLE SECTION. PER SEAT LENGTH IS @ 520 MM & SEATING HEIGHT IS @ 430 MM FROM GROUND . OWING TO THE SMOOTH FINISH, DURABILITY AND TENSILE STRENGTH BEAM MADE OF MILD STEEL 1.6MM THICK.SEAT IS MADE BY 1.2MM THICK MILD STEEL BORDER WITH CHROME PLATING FOR EVERY SEAT & BACK ; MILD STEEL HANDLES CHROME PLATED & DIE PRESSED LEGS AT THE END OF CHAIRS.GROSS WEIGHT OF REGULAR 3-SEATER WILL BE 31 KG.THE STEEL GRADE 202 HIGH YIELD STRENGTH AS PER IS:513 & IS:304 GRADE.THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

TEACHER TABLE TABLE SIZE : (W)1800MM X (D)600MM X (H)750MM MADE OF 25MM THICK PRELAM PARTICLE BOARD TABLETOP SUPPORTED WITH POWDER COATED "C" SHAPE METAL LEGS OF SIZE 50MM X 50MM AND CONNECTORS OF SIZE 40MM X 40MM. PROVIDING 0.8MM THK MS POWDER COATED CRCA SHEET PERFORATED MODESTY PANEL AT FRONT SIDE, BELOW TOP. IN BROWN-CLASSIC WALNUT COLOR WITH MAIN TABLE SIZE 1800MM(L) X 1050MM(D) X 750MM(H). Table which without wire manager.THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

CONFERENCE TABLE * SUPPLYING, AND PLACING IN POSITION OF 6 SEATER CONFERENCE ROOM TABLE, OFFERS YOU A GENEROUS WORKSPACE,DESK PRIMARY WORK SURFACE USE PREMIUM QUALITY MATERIALS.TABLE TOP SHALL BE MADE OUT OF 25 MM THICK PRELAMINATED PARTICLE BOARD OF GRADE II TYPE III OF IS 12823/LATEST,CONSTRUCTION PROVISION THE OVAL SHAPED CONFERENCE TABLE SIZE IS 6000MM (L) X 1200MM (D) X 750MM (H) TABLE TOP SHALL BE MADE OUT OF 25 MM THICK PRELAMINATED PARTICLE BOARD AND TOP BASED ON SIDE PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400 MM(L) X 715 MM(H) AND BELOW THE TABLE TOP MODESTY PANEL SHALL BE MADE 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 1559 MM(L) X 400 MM(H). * CONFERENCE TABLE EXTANDABLE PART COMES IN SEMICIRCLE SHAPED SIZE IS 1200MM (L) X 600MM (D) X 750MM (H).EXTANDABLE PART TOP MADE OUT OF 25MM THICK IN PRELAMINATED PARTICLE BOARD.TOP BASED ON CENTER PANEL SHALL BE MADE OUT OF 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 400 MM(L) X 715 MM(H) AND BELOW THE EXTANDABLE PART TOP MODESTY PANEL SHALL BE MADE 18MM THICK PRELAMINATED PARTICLE BOARD SIZE IS 200 MM(L) X 400 MM(H) .WHEN THE EXTANDABLE PART AND TABLE FIXED TOGHETHER SUPPORTING WITH 18MM THICK PRELAMINATED PARTICLE BOARD BOX SIZE IS 209 MM(L) X 400 MM(H).OUR WORK SURFACE FURNITURE IS FINISHED WITH EXPOSED EDGES SHALL BE FINISHED WITH 2MM THICK EDGE BINDING TAPE OF MATCHING COLOUR AND SHADE,FIXED WITH HOT MELT GLUE. (DWS/34763 Size:- 6000mm(L)x 1200mm(D)x 750mm(H))(EXT PART-3,CORNER PART-1)THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

WHITE BOARD Supply, Installation and Placement of Whiteboard Size 6'X4' Surface Material-Resin coated sheet surface, Core material(+- 2 mm Tolerance)- 9 mm thick Particle board, Backing Material - Melamine laminate sheet, Aluminium frame- Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285-2002 - Width of Aluminium Frame = 16mm thickness +- 3 mm tolerance, Surface suitable for writing with-Dry wipe Marker for White surface, Erasibility- Best with Wet cloth / Felt / Sponge and as per direction of Engineer-In-Charge.THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

3 SEATER SOFA SUPPLYING AND PLACING THREE SEATER EXCLUSIVE PREMIUM LEATHERETTE MODERNIST CLASSIC DESIGN LOUNGE SEATING SOFA SIZE IS 1905MM(L) X890MM(D)X 870MM(H) WITH KILN-DRIED WOOD FRAMING MAKES IT WARP AND SCRATCH RESISTANT,COMFORTABLE SEAT DEPTH & HEIGHT DESIGNED KEEPING MODERN INDIAN LIFESTYLE IN MIND,WRAPPED IN BUTTERY-SOFT PREMIUM LEATHERETTE, THE PANELLED BACK AND CUSHIONED ARMRESTS ENCOURAGE LOUNGING,DESIGNED WITH MODERNITY & ELEGANCE, CHOOSE THE OPTION THAT SUITS YOUR HOME. * COMBINATION CONSTRUCTION STRUCTURE ARE MADE IN MOISTURE CONTENT SHALL BE LESS THAN (10-12)%. THICKNESS OF PLYWOOD USED (MM) SHALL BE 12 MM GRADE IS 303 INDIAN STANDARD FOR COMMERCIAL (COMMON) AND MOISTURE PROOF PLYWOOD (TENTATIVE).UNDERSTRUCTURE FRAME SHALL BE CONSTRUCTED FROM 18 MM THICK KILN-DRIED GERMAN BEECH WOOD FRAMING IS HIGHLY DURABLE. THE COMPLETE STRUCTURE SHALL BE COVERED BY P.U.FOAM FIXED WITH ADHESIVE GLUE ,THE FRAME SHALL BE PADDED WITH HIGH RESILIENCE POLYURETHANE FOAM HAVING 28 +/- 5 DENSITY IN SEAT IT SHALL BE STACK FOAM OF 50MM THIK,40MM THICK BACK FOAM HAVING 20 +/- 5 DENSITY FOAM USED ,THERE SHALL BE CUSHION ARM 40MM THICK PROVIDED PADDED WITH HIGH RESILIENCE POLYURETHANE FOAM HAVING DENSITY 20 +/- 5. THE COMPLETE STACK FOAM STRUCTURE SHALL BE COVERED WITH PREMIUM LEATHERETTE IN BLACK-EERIE BLACK-COFFEE BROWN,BROWN-BURNT UMBER COLOUR, IT COMPLEMENTS THE MODISH LEGS ARE MADE BY ROUND SHAPE IN PVC MATERIAL. ( SEAT : 510 MM(D) X 445MM(H) , ARMS HEIGHT @ 620MM / BACK HEIGHT @ 460MM )THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

BOOK STACK- OPEN FROM FRONT * SUPPLYING, AND PLACING IN POSITION SLOTED ANGLE RACK OF SIZE 900MM(L)X 450MM(D)X 1800MM(H) SLOTTED ANGLE RACK -CLSOED FROM TWO SIDE 7 SHELVES INCLUDING TOP & BOTTOM ANGLES : 40MM X 40MM X 2MM(THICK). SHELF : 36X15X1MM CRCA SHEET. IN COLOR GREY (Approved Brand - Durian/ Godrej/ Featherlite)

MAGAZINE RACK DEVENT COLLECTION Free-standing and Wall Mounted Magazine & Newspaper Rack SIZE IS 900 MM (L)X 400 MM (D)X 1100 MM (H), LIBRARY BOOKS STORAGE SHELVES AND SHUTTER TO BE MADE UP OF 18 MM THICK PRELAMINATED PARTICLE BOARD, CONSTRUCTION IS 5 SHELVE IN BETWEEN PER SHELVE @ 55 MM THICKNESS , OVER ALL HEIGHT OF PRODUCT IS @ 1800 MM .T (Approved Brand - Durian/ Godrej/ Featherlite)

PRINCIPAL TABLE PREMIUM SUITES DIRECTOR TABLE STRUCTURE OF L SHAPED DESK . PRIMARY WORK SURFACE OVER ALL SIZE IS 2200MM(L)X 2000MM(D)X 740MM(H) 45MM THICK TABLE TOP MADE OF PRELAMINATED PARTICLE BOARD WORK SURFACE WITH WARM WALNUT FINISH, 2MM THICK PVC EDGE BANDING MADE OF SAME MATTE FINISH. SIDE PANNEL IS MADE OF 45MM THICK . * PROVISION OF SIDE RUNNER/A OF SIZE IS 2000MM(L)X 500MM(D)X 700MM(H) ,(COMBINATION CONSTRUCTION- TABLE TOP BASED ON SS STUD GRADE 304 LEFT SIDE BELOW FROM TABLE TOP SIDE RUNNER/A HAVE 2 DOORS STORAGE + 3 DRAWERS WITH CETNRAL LOCK HANDLES + 1 OPEN BOX FIXED SHELVE & RIGHT SIDE BELOW SS STUD 1 FIXED PEDESTAL TOP 18MM THICK . * FIXED PEDESTAL OF SIZE 464MM(L)X 500MM(D)X 646MM(H) , HAVING 2 DRAWERS + 1 FILLING DRAWER WITH CASTORS IN PROVIDED WITH CETNRAL LOCK FOR SECURITY AND HANDLES ARE PROVIDED FOR EASY OF OPENING. (Approved Brand - Durian/ Godrej/ Featherlite)

PRINCIPAL CHAIR SUPPLYING AND PLACING OF HIGH BACK CHAIR MATERIAL & SUBTYPE PREMIUM LEATHERETTE UPHOLSTERY MATERIAL PREMIUM LEATHERETTE SEAT MATERIAL PREMIUM LEATHERETTE LEG MATERIAL CHROME FINISH GLOSSY COLOUR & COLOUR FAMILY BROWN DIMENSION (W)655MM X (D)500MM X (H)1230MM MECHANISM SYNCHRO MULTI LOCKING SEATING CAPACITY 1 SEATER SEATING HEIGHT 540MM MAXIMUM SEATING HEIGHT 530 FUNCTION REVOLVING, TILT TENSION CONTROL, PNEUMATIC HEIGHT LIFT SIZE STANDARD STYLE CONTEMPORARY ASSEMBLY TYPE KNOCK DOWN SKU CAMDEN/HB THE SELLER / COMPANY SHOULD BE ISO 9001:2008, ISO 9001:2015, ISO 50001:2018, ISO 14001:2015, OHSAS 18001:2007,GREENGUARD, GREEN PRO, AIOTA, INDIAN DESIGN MARK AND FSC CERTIFIED.THE BIDDER SHOULD BE A MEMBER OF BIFMA AND AT LEAST TWO PRODUCTS OF THE OEM SHOULD BE CERTIFIED AS BIFMA COMPLIANT AND AN OFFICIAL PRODUCT OFFICIAL LINK/SCREENSHOT OF THE PRODUCT LISTING MUST BE PROVIDED FROM WWW.BIFMA.ORG". (Approved Brand - Durian/ Godrej/ Featherlite)

Providing and Installing, Testing & Commissioning of 13 Passenger automatic (machine room less) Lift , including one year free maintenance which will be start from handing over the lift, all taxes and all complete as per following detail specifications. APPROVED BRAND - SCHINDLER/ OTIS/ JOHNSON

PRODUCT- DETAIL- OTIS GeN2-Nova_MRL-1MPS/ Schindler 3000/ Johnson Nextra

CAPACITY(Kgs) - 884 kg 13 persons.

SPEED(mps) - 1mps.

STOPS - 4 Stops with (all opening on the same side)

CONTROLLER TYPE - ACD5-MRL

DRIVE - VF Regenerative (Closed Loop)

POWER SUPPLY - 400/415 Volts (3 phase AC)

OPERATION - Full collective operation.

CAR GROUP - One car (simplex)

MACHINE - PM Gearless (Located in shaft on top of guide rails)

TRACTION MEDIA - Flat Coated Steel Belt.

CAR FINISH -

Rear Mid Panel= Stainless Steel # 4 (Hairline)

Rear Corner Panel= Stainless Steel # 4 (Hairline)

Side Panel= Stainless Steel # 4 (Hairline)

Front Panel= Stainless Steel # 4 (Hairline)

FALSE CEILING TYPE - CD-41

FALSE CEILING FINISH - Stainless Steel # 4 (Hairline)

VENTILLATION - Cross flow fan.

HAND RAILS - Stainless Steel Mirror Finish Handrails on rear car panels

FLOORING - Vinyl Tiles

CAR DOOR FINISH - Stainless Steel # 4 (Hairline)

LANDING DOOR FINISH - Stainless Steel # 4 (Hairline)

FIRE RATED DOORS - Not Available

PIT DEPTH - 1350

OVER HEAD - 4300

CAR & HOISTWAY DOOR TYPE- Central opening (CO) doors

DOOR OPENING (W x H- MM )- 900mm W x 2000mm H

DOOR OPERATOR- DC Door Operator

COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline)

CAR POSITION INDICATOR- Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display

HALL FIXTURES- O2000 Pan Type Fixture ,

HALL FIXTURES FACE PLATE- Stainless Steel #4(Hairline)

HALL BUTTON ARRANGEMENT- LCD Monochrome type

STANDARD FEATURES- Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off

OPTIONS INCLUDED- Grounding Switch, Automatic Rescue operation, Voice Synthesizer, Audible Car Call Button, Emergency Power Operation, Parking Key Switch ,

100 KLD ETP PLANT (EFFULUENT TREATMENT PLANT) . Design, supplying, installing, testing & commissioning of Effuluent Treatment Plant. The Effuluent Treatement shall be based on MBBR technology. The nature of effluent is domestic Waste water from wash areas which shall be discharged into the ETP. Plant. The scope shall include design and execution of all electrical, mechanical, plumbing, processing, ancillary equipments and works etc required to complete the package along with getting approval from the state pollution control board, other statutory bodies as well as from the design consultant. The scope also includes the design of Electro mechanical elements. Execution of civil works shall be in the scope of the Civil contractor as per the design of the ETP vendor. Design to take consideration as given below

Nature of effluent - Effuluent from Waste areas

Daily average flow - 100 KLD / Per Day

PH : 2.93PPM Total Suspended Solids : 75 ppm Biological Oxygen demand : 1008 ppm Chemical Oxygen demand : 2279.4 ppm Oil & Grease : 9.5 ppm

Effluent discharge standard after treatment :

PH : 6-7.5PPM Biological Oxygen demand : < 50 ppm Chemical Oxygen demand : <200 ppm

LIST OF MECHANICAL EQUPMENT-

01 Bar Screen 0.5m x 0.5m 2nos SS/MS

02 Defused Aerating system 1 lot PVC /PP Pipe, Make - ASTRAL /SUPREME/FINOLX

03 Valves & inter connector pipe work 1 lot PVC /PP Pipe, Make - ASTRAL /SUPREME/FINOLX

04 Tube modules 1 lot PP

05 Accessories for primary and secondary clarifier 1 lot MS/PVC Pipe, Make - TATA/JINDAL

06 Alum solution tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - TATA/ PAINTAIR/EQV

07 Lime solution tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - TATA/ PAINTAIR/EQV

08 Poly electrolyte tank with agitator 100 ltrs (FRP/eqv) 1 No., Make - V

09 Blower 5 HP 2 Nos. (1W+1S)., Make - A1/ AKASH/EQV

10 Dosing Pump 100 L/Hr, 5Kg/cm2(Metering pump)3 Nos., Make - E-DOSE/EQV

11 Dosing pump 5 L/Hr, 5Kg/cm2 1 No., Make - E-DOSE/EQV, Make - KIRLOSKAR/KSB/WILLO

12 Effluent transfer pump capacity 4m3/hr 2Nos (1W+1S).

13 Slag recirculation pump 1 No (1W), Make - KIRLOSKAR/KSB/WILLO

14 Filter feed pump capacity 4m3/hr 2 Nos. (1W+1S)., Make - KIRLOSKAR/KSB/WILLO

15 MBBR Media 1 Lot.

16 Two stage Filters (FRP vessels) 2 Nos.(DMF/ ACF), Make - TATA/ PAINTAIR/EQV

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, Schematic flow diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete work.

LIST OF INSTRUMENTS

1. Pressure gauges 2 nos./ All Pumps, Make - H.GURU/EQV

2. Float switch -3 Nos for all pumps, Make - DANFOSS/EQV

3. Rota meter

LIST OF ELECTRICAL ITEMS

01 Control panel with automation system 1no., Make - L&T/SCHNEIDER/EQV

02 Power cable, Make - POLYCAB/HAVELLS/ EQV

BAR SCREEN

Main Frame - MS Flats, 25 wide x 5 thick min.

Bars - SS round bars 4 mm dia.or as per Vendor

Bar Spacing - 8 mm or as per Vendor

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Accessories - Anchor Fasteners for fittings, matching comber with long handle (MS) for removing floating solids.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Float switch with Automatic Operation

All pumps will be operated with float switch with Automatic Operation connected with the control panel

MS hot dip galvanized puddle flanges as required to be provided (in the structural slab and wall) of various diameters. Puddle flanges shall be provided for all the structural component of the ETP.

Note: Supply and Installation of Puddle Flanges shall be done by the Civil contractor. However, all design drawings, specifications, technical data and site supervision shall be done by the ETP vendor

Plastic manhole step or foot rest 30mm reinforcing bar. of the foot in various tanks/ components of the ETP for the purpose of accessability. The installation of the foot rest shall be done by the civil contractor as per civil GA drawing

Note: Supply and Installation of Foot rests shall be done by the Civil contractor. However, all design drawings, specifications, technical data and site supervision shall be done by the STP vendor

Supply of vent pipes of 100 mm dia UPVC pipe with mosquito proof grating suitable for the ventilation purpose of the various tanks., Make - ASTRAL/SUPREME/FINOLEX

Note: Supply of Vent Pipes shall be in scope of ETP vendor. Installation shall be done by the Civil contractor under the supervision of the ETP vendor

DEFUSED AERATING SYSTEM

Supply installation of Defused Aerating System.

Supply installation of PVC, EPVC, GI pipe fitting including valves, fittings with inter connecting piping work.

Air diffusion system

Air piping shall comprise of pipes droppers/ laterals with MS (epoxy coated) Header and all drop pipes in PVC or GI complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good.

EQT - 1 No., AERATION TANK - 1 No., MBBR Tank - 2 Nos.

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid in SS304 shall be assembled in modular form so that they can be replaced / repaired

Fine bubble diffusers in SS304 (Capacity 4 m3/hr or as per Vendor)

For EQT - 1 No., SHT - 1 No., MBBR Tanks - 2 Nos.

Note : Air dispersion system shall be provided for Equalisation Tank, Sludge holding Tank and MBBR Tank.

Providing and fixing all piping (as described below) and isolation control valves for making the system complete.

GI/PVC piping :Pumped effluent & tank overflow pipe line

MS Epoxy : Non Submerged Air piping

GI/PVC piping :Pumped effluent & tank overflow pipe line

TUBE MODULES

Supply installation of Tube Modules.

ACCESSORIES FOR PRIMARY AND SECONDARY CLARIFIER

Supply installation of Accessories like MS and PVC pipe fitting, valves etc.

ALUM SOLUTION TANK WITH AGITATOR

Supply installation of 100 ltrs FRP Tank with Agitator

LIME SOLUTION TANK WITH AGITATOR

Supply & installation of 100 ltrs FRP Tank with Agitator

POLY ELECTROLYTE TANK WITH AGITATOR

Supply & installation of 100 ltrs FRP Tank with Agitator

BLOWER TWINLUBE

Supply & installation of twin Blower 1 w /1 std by

DOSING PUMP , Make - E-DOSE /EQV

Supply & installation of Dosing Pump

Providing and fixing chemical dosing system with all accessories, suitable to doze chemical soluktion upto 1 ppm doze (of Sodium Hypo-chloride solution) to a filtered water flow of 4000 lph. against a pressure of 1.5 kg/cm2 complete with FRP moulded solution holding tank of min. 100 litre with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc.complete as required and as specified.

System : Metering Type

Capacity : 0-5 LPH

Feed Solution : Hypochlorite

Conc. Of Solution : 0.1

MOC and Capacity of Tank : HDPE - 100 Litres

EFFLUENT TRANSFER PUMP, Make - KIRLOSKAR/KSB/WILLO

Raw Sewage Lifting Pumps, Make - KIRLOSKAR/KSB/WILLO

Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open CI impeller, CI casing and SS Shaft, suitable for operation on 415 volts ± 10% , 3 Phase motor, 50Hz, A.C supply, speed 2900 RPM, including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following :

Pump Headers and other interconnecting pipes

Complete inlet, outlet and header piping of suitable dia (velocity shall not exceed 1.5m/s) -- 1 Lot

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

Necessary cables from pump sets to pump starter panel - 1 Lot

Discharge : 4 m3/Hr

Head : 15 m

Solid Handling : 30-35 mm

Pumps shall be operated on cyclic timing with automatic timer set

One set consist of 2 nos. of pumps - 1 working & 1 stand by (Complete set as above no. pumps including cost for valves, piping, Control Panel, Cabling, contactors, breakers, overload relay, float switch, level indicators, pressure gauges etc as required and as specified and any other additional items to make the system complete)

SLAG RECIRCULATION PUMP, Make - KIRLOSKAR/KSB/WILLO

Providing and fixing vertical multistage centrifugal clear water pump set with SS casing, SS impeller, SS-316 shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply (with cartridge type mechanical seal), pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation complete in all respects and as per specification with the following capacities:

Capacity : - 5.0 m3/hr

Head : - 18-20 m

Note-CIP pumps can be common with item no.c

Motor Efficiency Class - IE3

Supplying, Installation, testing and commissioning of chlorine dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5LPH for dosing.

Supplying, Installation, testing and commissioning of CIP Dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5 LPH for dosing.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supplying, Installation, testing and commissioning of CEB Dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump of 0-5LPH for dosing.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supply, installation & commissioning of HDPE backwash tank of 500 Litre capacity including required level controller

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Supply, installation, testing and commissioning of top discharge Stainless Steel bucket type Centrifuge of Suitable Capacity suitable for 100 KLD ETP capacity with feed pump (Monoblock Centrifugal Self Priming Type) – 2 No. (1 working + 1 standby) with 1 No. standby stator, associated valves, pressure guage, level switches, polymer dosing tank, interconnecting piping and poly dosing system and other associated piping, valves and items as per approved P&I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing & fixing on line pH meter digital type for Monitoring the online pH after Ultrafiltration. Including electrical wiring from panel to flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect.

At Sewage Inlet

At Raw Sewage Pump Outlet Rotameter

At Filter Feed Pump outlet Rotameter

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

FILTER FEED PUMP

Supply & installation of mono block pump with the capacity of 4m3/hr @15 meter head- 01 working & 01 stand by., Make - KIRLOSKAR/KSB/WILLO

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing and fixing vertical multistage centrifugal clear water pump set with CS casing, CS impeller, CS shaft, CI base with CED coating, complete directly coupled with TEFC induction motor of class "F" insulation, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply (with cartridge type mechanical seal), pressure gauges with gunmetal isolation cocks, vibration elimination pads, etc. mounted on a MS base frame bolted to cement concrete foundation complete in all respects and as per specification with the following capacities:

Complete inlet, outlet and header piping of suitable dia -1 LOT

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Butterfly valve and Dual Plate NRV of appropriate dia and rating - 1 Lot

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Discharge : 4 m3/Hr

Head : 15 m

No. of Pumps : 2 (1W+1S)

Motor Efficiency Class - IE3

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Operation of pump shall be based on level controller proposed to be installed in tank as per site location.

The cement concrete foundation shall be 200 mm high and 150 mm projection on all sides of M.S. base frame shall be designed by the STP Contractor and executed by the Main Civil Contractor.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

MBBR MEDIA

Supply, installation, testing and commissioning of PVC MBBR media to be installed in MBBR Tanks PRIMARY CLARIFIER AND SECONDARY CLARIFIER (2 Nos.) and PVC tube deck settling media to be installed in Secondary Settling Tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Vendor to specify Surface area and flow rate

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

DMF FILTER/ MF FILTER

Dual media filter FRP vessel with multi port valves accessories and filter media 600 mm dia with height of 1800 mm flow rate @4000 LPH back wash flow rate 200 LPH operating pressure 3kg/cm2

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves designed on 1.50 m / sec velocity.

ACF FILTER

Dual media filter FRP vessel with multi port valves accessories and filter media 600 mm dia with height of 1800 mm flow rate @4000 LPH back wash flow rate 200 LPH operating pressure 3kg/cm2

ELECTRICAL INSTALLATION FOR ETP, CONTROL PANEL WITH AUTOMATION SYSTEM INCLUDING CABLE TRAY WITH CABLE

Also, refer to General Notes and Specifications for Panels/ Boards

GENERAL NOTES FOR MCCB's:

ACB's & MCCB's shall be of 3P or 4P as called for in the BOQ.

Ics = Icu = 100% for the MCCB's, MPCB's & ACB's

MCCB's shall be with extended rotary handle.

Only one make of switchgear to be used in a board /panel.

All communicable meters should be looped inside the panels and this loop has to be brought to one terminal point in the panel for connectivity.

No BMS cable should be directly connected to VFD and hence these points will have to brought on to the terminal blocks inside the panel.

All energy meters shall be dual source and communicable type.

The power factor capacitors shall be of inert gas type and shall be suitable for 525 volts operation.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

IP Rating : IP54

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Incomer:

• 1 No. 63A, 3P, MCCB, 25 KA of suitable rating as per load.

• MCCB shall be with inbuilt micro-processor based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Incomer Indications:

• R,Y,B phase indication lamps

• ON/OFF, Trip indication lamps

• Indication lamps shall be LED type (63V)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Incomer Metering:

• 1 No. combined Digital VAF meter

• Meter shall be (110V) and communicable type.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

CT for Incomer Metering :

• CT metering Class-1 accuracy CT’s (one per phase)

• CT shall be cast resin type & shall be of suitable burden (VA) & ratio.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

PT for Incomer Metering & Indication Lamps:

• 415V / √3 / 110V / √3 PT for metering and indication lamps.

• PT shall be Class-1 accuracy.

• PT shall be cast resin type.

• PT shall be of suitable burden (VA).

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Protection for Metering PT:

• TP MPCB of suitable rating & fault withstand capacity on primary side of PT.

• TP MCB of suitable rating on secondary side of PT.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Bus Bars:

• 100A, 3P, 25 KA, Aluminium Bus Bars of electrolytic grade with heat shrinkable sleeves.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

110V Control Transformer for Contactor Coils of Starters & out goings Indication lamps:

• 1 No. 415V / 55-0-55 V, cast resin control transformer.

• Transformer to be of adequate burden.

• Transformer with primary taps at ± 2.5%, ±5%, 50HZ, centre tap earthed.

• 110V control bus.

• TP MPCB of suitable rating & fault withstand capacity at Primary side & DP MCB at secondary side of control transformer.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Outgoings

DOL Starter Feeders for:

• 2 Nos. for Sludge Recirculation Pumps (1W+1S)

• 2 Nos. 3.73 KW for Filter Feed Pumps (1W+1S)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

• 2 Nos. for Screw Pump (1W+1S)

• 2 Nos. for Air Blower (1W+1S)

Spare DOL Starter Feeders for:

• 1 Nos. 3.7 KW motor.

• 1 Nos. 5.6 KW motor.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for Sewage Sump Pump Panel / Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for etp Sump Pump Panel / Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for ETP Bypass Sump Pump Panel (without starter):

• 0 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for Soft Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for Flushing Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Feeder for Irrigation Water Transfer Pump Panels (within pump room) (without starter): No. of feeders - 1

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 4.5 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Spare Feeder similar to above (without starter):

• 1 No. 3P, MCCB, 25 KA of uitable rating as per load of 11.2 kW.

• MCCB shall be with inbuilt adjustable thermal magnetic based O/C & S/C releases.

• Both the releases shall be with adjustable trip settings.

• MCCB with 1NO + 1NC contacts and an auxiliary trip contact for BMS.

• ON / OFF / TRIP Indication lamps LED type 110 V.

• Digital Ammeter.

• 3 Nos. metering Class 1 accuracy cast resin CT's of suitable ratio & burden.

AUDIO SYSTEM FOR CONFERENCE ROOM

DIGITAL WIRED CONFERENCE SYSTEM: Chairman Discussion / Conference Unit Supplying, Installation, Testing & Commissioning of Digital Chairman Discussion /Conference Unit with Removable Microphone of minimum Length 400mm Chairman Discussion Unit with built-in Digital Signal ProcessingUnit with Priority and Next-in-Line Configuration Priority button silences all delegate microphones and allows only the chairperson to speak; Next-in-line button gives the floor to the next speaker in a waiting list of speakers who requested to speak. User Button with Feedback; Shielded microphone, immune to mobile phone interference, High-quality integrated loudspeaker; Headphone output with Volume Adjustment Loop-through, daisy-chain cabling; Unit with Bi color bar indicator Compatible Screw Lock Microphone of length 400mm Different LED Signalling for Mic On/Off OR Request-to-Speak Push Button or better Audio Quality 16Bit digital; Frequency response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Microphone with Ring Indicator to light up Red when active and Green when in Request Connection: Screw Lock Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

Delegate Discussion / Conference Unit s. Supplying, Installation, Testing & Commissioning of Digital Delegate Discussion / Conference Unit with Removable Microphone of minimum Length 400mm Delegate Discussion Unit with built-in Digital Signal Processing Unit with Microphone On / Off Button; User Button with Feedback Shielded microphone, immune to mobile phone interference High-quality integrated loudspeaker; Headphone output with Volume Adjustment Loop-through, daisy-chain cabling; Unit with Bi color bar indicator Compatible Screw Lock Microphone of lenght 400mm Different LED Signalling for Mic On/Off OR Request-to-Speak Push Button Connectivity: 2 digital bus connections (IN/OUTinterchangeable), Headphone connection. Audio Quality 16Bit digital; Frequency Response: 25 Hz-15,000 Hz (± 3 dB) or better Microphone with 400 Gooseneck Length; Polar Pattern: Unidirectional, Cardioid Max SPL @ 1kHz: 110 dB SPL (1% THD+N) or better S/N Ratio: > 67 dB(A); sensitivity: (-40.5±2) dBV @ 1Pa, 1KHz or better Connection: Screw Lock Microphone with Ring Indicator to light up Red when active and Green when in Request Material: Brass; Certification: CE need to submit; 2M CAT5e cable from the same OEM Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

Supplying, Installation, Testing & Commissioning of Conference connection cable, 10m, black and other interconnecting cables, jacks etc should be from The Same Brand and Interconnecting cables, Microphone cables, speaker cables, special Cat-5 cables for Conference system, PVC Conduit, Power Sockets etc.

Supplying, Installation, Testing & Commissioning of Two way passive loudspeaker including wall mount bracket Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

Supplying, Installation, Testing & Commissioning of Digital Mixing amplifier - Suitable for above Speakers, Approved make : Televic / Bayerdynamic / Marcony Technology / Audix

AUDIO SYSTEM FOR LECTURE THEATRE

Supplying, Installation, Testing & Commissioning of Digital Podium with in built Audio and Digital system Smart Rostrum has PC with i3 processor, 4GB RAM, 500 HDD, DOS and Keyboard/Mouse, and can be customized to as per the requirement. Smart Podium has sliding top tray to place Laptop which allows presenter to display any multimedia file instantly. It is fully compatible with all types of Projectors. It has switching plate with buttons on the top, which allows you to display desired projection output, We integrate high quality, echo-free and branded audio equipment in Smart podiums, All cables and connectors inside the podium are tagged and well managed to simplify the structure complexity. 18” gooseneck microphone from premium brands integrated with the Smart Podium. It has 2 XLR ports on the top. All the doors, drawers, trays and shelves are lockable to avoid unauthorised access. It has in-built anti-theft mechanism. Switcher helps to switch the projection among different devices, while splitter helps to split the display for multiple outputs. Smart podium should have all the required input/output ports such as USB, VGA in/out, HDMI in/out, LAN, Audio in/out, XLR, Power and so on. Podium allows you to connect smart board with the projector directly, and helps you to conduct interactive lectures. It integrates full HD Document Camera which helps to project live document/object for audience with greater clarity, Podium has 4 caster wheels which enable it to move easily and effortlessly. Controller helps to operate all the electric & electronic devices using its touch screen etc. Approved Brand – VAC / INGRESS / ITC / LIBERTY

Supplying, Installation, Testing & Commissioning of Audio Power Amplifier: OPERATION MODES Stereo Mode Bridged-Mono Mode Load 8Ohm 4Ohm 8Ohm 4Ohm 70V (22Ohm) 100V (33Ohm) Maximum Continuous Power (@1khz, 1% Thd) 2 x 140W 2 x 140W 1 x 280W 1 x 260W 250W 240W Maximum Dynamic Power (@1khz, 1% Thd) 2 x 200W 2 x 275W 1 x 550W 1 x 550W 550W 550W Frequency Response 20-20kHz (+/-0.3dB) Peak Output Current 25A Dynamic Range 112dB (A-weighted) Noise Level -76dBu (A-weighted) Distortion (1kHz@1W/8Ohm) 0.003% Distortion (1kHz@50W/8Ohm) 0.011% (Stereo) 0.004% (Bridged-Mono) Crosstalk (1kHz@1W/8Ohm) -95dB Gain 26dB/32dB Maximum Input Level +24dBu Amplifier Version QX-300A QX-300D Input Type Analogue Balanced 3-pin Phoenix (5.08mm pitch) Dante RJ-45 (AES67 Compatible) with RJ-45 Link Input Sensitivity +7dBu/+4dBu -4.5dBFS/- 1.5dBFS Input Impedance 10kOhm - Maximum Input Level +24dBu 0dBFS Output Resistance 22.5mOhm/43.6mOhm Front Controls Volume Adjust, 80Hz HPF Enable, Bridged-Mono Enable, Limiter Enable, Auto-Standby Enable) Approved Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

Supplying, Installation, Testing & Commissioning of Wall Mounted Weather Proof Speakers Max SPL *calculated 112 dB Sensitivity *5-band average 93 dB Frequency Response 75Hz – 20kHz±2dB Impedance 16Ω Transformer Taping 100V 20w/30w/40w/60w 70V 10w/15w/20w/30w Amplifier Power RMS 100W Peak 200W Transducers HF 25mm Titanium Dome Tweeter LF 8” High Performance Polypropylene Woofer Directivity *H x V 150° x 120° -10dB Connections Captive Screw Terminal Plug (In/Thru) Environmental Ingress Rating Speaker Cabinet IP56 (IP67 when used with IPMX1 kit) Dimensions *H x W x D 345 x 202 x 243mm Net Weight 4.3 kg Shipping Weight 6.0 kg Approved Brand – QUEST / EQUIPSON (WORK) / CROWN / MAYERSOUND

Supplying, Installation, Testing & Commissioning of 6 channel Audio Mixer. Digital Echo 20 – 400 m/s. Frequency 25 Hz – 25 KHz. MP3 Player with Bluetooth, Display & Remote available. Input Gain: –50 dB to 6 dB gain range with overdrive indication.. Output: 0 dBm / 17 dBm (775mv / 5.5v). Equalization: Bass & Treble ±5 dB. Controls: Gain, Eq., Pan, Echo, Fader. Power Supply: 220V 50Hz AC ± 10% (In separate enclosure) Dimension: 295 (W) x 165 (D) x 80 (H) mm. Weight: 1.630 kg (approx.) Approved Brands – Shure / Equipson / Bose/ Mayersound/ STRANGER

Supplying, Installation, Testing & Commissioning of Wireless UHF Lapel / Collar Microphone system Specifications Audio Input Level: –20 dBV maximum * Input Impedance: 22 kΩ RF Output (dependent on applicable country regulations): HI power mode: 10 mW maximum * LO power mode: 1 mW maximum Weight: 270 g (10.2 oz.)(without batteries) * Housing: Molded ABS Power Requirements: 2 “AA” size alkaline or rechargeable batteries Approved Brand – Shure / Equipson / Bose/ Mayersound/Audio Focus/

Supplying, Installation, Testing & Commissioning of Green Chalk Board, Size 6 ft x 4 ft. Green ceramic board 1200mm x 1800mm - The writing surface shall be made of steel sheet of thickness 0.3 to 0.4 mm having vitreous enamel coating of 0.11 mm minimum thickness of top and 0.03mm minimum on the back with free from waviness and show no scratches on using HB to 3H pencils for writing. The surface of the writing board shall show excellent eraseabilty when specified writing medium is used. The core material should be 7mm thick MDF. Backing shall be of electro galvanised steel sheet. The board shall secured from all side with extruded aluminum alloy hollow section frame duly anodized and shall have front: 20mm, side: 16mm and wall thickness: 1.2mm. 4 nos. ABS corner grey color should be provide at all corners of the board.

Supplying, Installation, Testing & Commissioning of connection cable, interconnecting cables, jacks etc and Interconnecting cables, speaker cables, PVC Conduit, Power Sockets etc., suitable cabinet for storing and operating the full system for above works with all complete.

AIR CONDITIONING WORKS (VRF SYSTEM)

INDOOR UNIT . Supplying, Installation, Testing and Comissioning, Loading, Unloading of the indoor unit. Unit shall be complete in all respect and suitable for 230 ±5% volts include wired thermostat having a display showing temperature and control of temperature inside the room. The Quoted Price shall include hanging arrangement of the unit with necessary supporting rod, nut & bolts, fastners and accessories for complete installation of Indoor unit. User shall be able to adjust the temperature as per their comfort level requirement. The quoted price shall be inclusive of corded remote controller.

Hi Static Ductable & Concealed Unit

ACCESSORIS

Branch joint pipe

ODU Twinning Kit

Wired Remote Controller

REFRIGERANT AND DRAIN PIPING WORK

REFRIGERANT PIPING

Supply, fabrication, installation, testing of Interconnecting refrigerant copper pipe work with closed cell nitrile rubber tubular insulation with GC cloth rated for "O" Class between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with channel support. Refer tender specification for detail description.

41.3 mm O.D (wall Thickness-1.2 mm) (Insulation: 19 mm)

34.9 mm O.D (wall Thickness-1.0 mm) (insulation: 19 mm)

28.6 mm O.D (wall Thickness-1.0 mm) (insulation: 19 mm)

22.2 mm O.D (wall Thickness-1.0 mm) (insulation: 19 mm)

19.1 mm O.D (wall Thickness-1.0 mm) (insulation: 19 mm)

15.9 mm O.D (wall Thickness-1.0 mm) (insulation: 19 mm)

12.7 mm O.D (wall Thickness-0.8 mm) (insulation: 13 mm)

9.5 mm O.D (wall Thickness-0.8 mm) (insulation: 13 mm)

34.9 mm O.D (wall Thickness-0.8 mm) (insulation: 13 mm)

CONDENSATE DRAIN PIPING

Supply, installation, testing and commissioning of Rigid heavy class uPVC piping with minimum 9 mm nitrile rubber insulation over the pipes, complete with fittings, supports trap arrangement, clean plug and accessories for units as per specifications and technical specification.

25 mm dia.

32 mm dia.

40 mm dia.

AIR DISTRIBUTION WORK

GSS DUCT (FACTORY FABRICATED) . Supply, fabrication, installation, testing and commissioning of GSS sheet metal ducting complete with vanes, splitter dampers, fire retardant gaskets, hanging arrangement including fully threaded GI rods and GI "C" channels/ rolled steel wires or Grapple Wire Rope Hangers & Supports complete with end fixing as approved by clients/consultants in accordance with the approved shop drawings and specifications. Quoted price shall be inclusive of necessary scaffolding charges towards installation of supply/return/exhaust/fresh air ducts outside or within building wherever required. Refer tender specification for detail description.

DUCT THERMAL INSULATION Supply, Installation, Testing and commissioning of thermal insulation material for supply duct insulation. It shall be anti-microbial closed cell elastomeric nitrile rubber insulation with aluminum foil. Thermal conductivity of the insulation material shall not exceed 0.037 w/m°K at an average temperature of 20°C. Density of the material shall be 45-55 Kg/m³. The product shall have temperature range of –40 °C to 105 °C. The insulation material shall be fire rated for "Class 0" for surface spread of flame test. Water vapors permeability shall not exceed 0.15ng/Pa.Sec.m. Thermal conductivity of the material shall not be affected by ageing, as per DIN 52616. The material must be tested for ageing effect in an accredited laboratory for a minimum period of five years to satisfy the ageing criteria. The smoke density of the material shall not exceed 1. There shall be no toxicity in the emitted smoke, both under flaming and non-flaming conditions. The quoted price shall include water-based adhesive and accessories required to fix the insulation outside the duct.

13 mm on supply duct

DUCT ACOUSTIC LINING . Supply, Installation, testing and commissioning of duct acoustic lining of supply air duct and plenum with 10 mm thick Open Cell engineered Nitrile Rubber foam of density 140-180 kg/cu.m within built Microban and tested as per ISO 354:2003 complete as required and as per specifications.

10 mm Thick Lining

DOUBLE LAYER CANVAS CONNECTION . Supply, Installation, testing and commissioning of double Layer canvas connection fire retardant cloth for the end connection of Ductable indoor unit and Exhaust fan to reduce the vibration. It shall be fire rated for atleat 2 hrs. Refer tender specification for detail description.

VOLUME CONTROL DAMPER - FOR RECTANGULAR DUCT . Supplying, installing, testing & commissioning of GI volume control damper with minimum 1.6 mm flange and 1.8 mm blade thickness within ducts to be provided with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of the air distribution system as per schedules & drawings.

SUPPLY AND RETURN AIR GRILLE . Supply, installation, testing, balancing and fixing of Powder coated aluminum extruded grill with aluminum construction collar damper for supply air as per specification & the sizes will be as per schedules and drawing. Refer technical specification for detail description. The colour approval shall be taken from client/architect before ordering of material.

ELECTRICAL WORK

TRANSMISSION & CONTROL WIRING . Providing & fixing control cum transmission wiring in medium duty PVC Conduit between indoor and outdoor units.

1.5 Sqmm X 2 Core - Copper

Supplying, Installation, Testing and Comissioning Of Power Distribution Board with individual outgoing feeder for each outdoor unit with all complete job.

Supplying, Installation, Testing and Comissioning of Power Distribution Board for each indoor unit as required with all complete job..

Supplying, Installation, Testing and Comissioning of Power cabling with flexible copper cable inside PVC conduit as required with OEM standard with all complete job.

Providing and fixing 15" to 18" ht. stainless steel text & logo of college (as approved by college authority) with radium finish and including all taxes, etc. complete job.

Providing and finishing wall with Tribal art work (as per approved) with weatherproof plastic emulsion paints for Sohrai, Kohbar, Saura, Paithkar, Jadupetiya, Kalighat and Madhubani artwork, Etc. as per approved deign and required including all materials and scaffolding, etc. all complete job.

Providing Artistic glass mosaic Murals (as per approved) , including designing, all materials, labours, scaffolding with all complete.

Add 18% GST

Add 1% Labour cess 1%

M/S MADAN PRASAD (BID ID -657074)

M/s Raj Construction (BID ID -657436)

MANOJ KUMAR SINGH (BID ID -656288)

M/S S K TEKRIWAL (BID ID -657407)