Construction of civil foundation for compressor inside new compressor air station and allied civil works.

15.2.2 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:4:8 leaner mix ( including equivalent design mix)

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.19 : Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per directions of Engineer -in-Charge.

15.57 : Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

od37244/2022_2023 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal & disposal of rubbish,scrap,pipes etc up to a distance of 50 m outside the periphery of the area cleared.

15.13.2 : Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 50 metres lead:Of area beyond 3 sq. metres

od4800/2022_2023 : Disposal of building rubbish/ malba/ similar unserviceable, surplus earth, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved dumping ground or as directed by Engineer-in-charge, beyond 50 m initial lead and up to 1000m , for all leads including all lifts involved

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

od26776/2022_2023 : Bailing out water/slush using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete.All deposits/slush shall be shifted to designated location with in 1km lead.

60.7.2 : DR PACKING Under foundation - Dry stone packing under foundation with good quality blasted rubble including conveyance of material and labour charges etc. complete as per direction of departmental officers at site.

od27974/2022_2023 : Supply,filling and compaction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness on prepared surface and compacting with plate vibrator to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.<br>With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30

od22645/2022_2023 : Providing and laying in position cement concrete of specified grade excluding the cost of OPC/PPC Cement,centering and shuttering - All work up to plinth level:(The required OPC/PPC Cement shallbe supplied by KMML at our store)<br>1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

od27088/2022_2023 : Providing and laying in position cement concrete of specified grade excluding the cost of OPC/PPC Cement centering and shuttering - All work up to plinth level:(The required OPC/PPC Cement shall be supplied by the company at our store)<br>1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

od24629/2022_2023 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:<br>1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) ( The required cement shall be supplied by KMML at our store)

od33907/2022_2023 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering,Cement and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.(The required OPC/PPC cement shall be supplied by KMML at our store)<br>All work upto plinth level

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od35057/2022_2023 : Supplying and filling in plinth with M sand under floors, including watering, ramming consolidating and dressing complete.

30.2.56 : Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.

5.28 : Providing and fixing in position 12 mm thick bitumen impregnated fibre board conforming to IS: 1838, including cost of primer, sealing compound in expansion joints.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

od34144/2022_2023 : Providing and applying protective coating of Cement wash over steel reinforcement as per direction of Engineer-in-charge. The product shall be applied on reinforcement steel after thoroughly cleaning. painted area of steel shall be considered for payment(The required cement shall be supplied by KMML at our store).

13.65.1 : Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work

od22647/2022_2023 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level(The required reinforcement steel shall be supplied by KMML at our stores)<br>Thermo - Mechanically Treated bars of grade Fe-500D or more

od24143/2022_2023 : Grouting pocket holes using flowable non shrink grouting material like conbextra GP2 or like as per manufactures specification inluding all labour,surface preparation,materials etc

od24144/2022_2023 : Providing,fixing and aligning pocket holes in concrete made out of plywood of size upto 20x20cm of deep 700mm as per direction of engineer in charge

od28206/2022_2023 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete.excluding cost of cement.(The required cement shall be supplied by KMML at our store)

13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.8.1 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

50.9.15.2 : Supplying and fixing 300 mm Aluminium aldrop

9.83 : Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

14.34 : Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

od27736/2022_2023 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):<br>With float toughened glass panes of 6.00 mm thickness

od27737/2022_2023 : Providing and fixing bright finished SS tower bolts (barrel type) with necessary screws etc. complete:<br>150x10 mm

od27738/2022_2023 : Providing and fixing 12 mm thick laminated marine plywood of approved brand and grade , in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.<br>Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

od27739/2022_2023 : Plastering with 12 mm cement plaster of mix:<br>1:4 ( 1 cement : 4 fine sand)(The required cement shall be supplied by KMML at our store)

od28259/2022_2023 : Finishing walls with Acrylic Smooth exterior paint of required shade:<br>New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)including all material,labour,tools,tackles,scaffolding etc.

od34994/2022_2023 : Labour charges for R.C.C chipping, repairing works of aluminium / steel doors / windows / ventilators and other related works in connection with aluminium fabrication and assosiated works proper finishing for Helper

U. AZEEZKUNJU