T-61/EDCP/2023-24

Amount

Safe carriage of following materials from store centre-Pilibhit to different sites under EDD-Pilibhit including loading & unloading (sites/location detail enclosed as annexure-10)

11/0.4 25 KVA Transformer

PCC Pole 8.5Mtr. Long

11 KV Ms T-Off channel.

Top channel (125x65x2040 mm.)

Base angel for S/s (75x75x6x2028) with complete nuts and bolts.

11 KV Disk Insulator composite 45KN (T&C type)

11 KV Pin insulator composite

11KV TPMO

11KV Composite Pin Insulator

Stay set Complete (Stay rod 16x1800 mm, wire 5 kg , clamp, bolt and nut with grouting)

Earthing com. (rod size 20x2500 mm,6 SWG GI wire etc.)

ACSR Weasel Conductor

LT lead XLPE Cable 3.5x70 sqmm

AB cable (3x50+1x35+1x16 sqmm)

Distribution box on pole including proper clamping.

Erection of the Single pole on PCC. Pole 8.5mtr long, complete work including-cutting, making holes, fixing of all types of accessories digging of pits complete in all respect, as per RESSPO drawing. nut, bolt washers would be provided by the contractor.

Erection of the Double pole structure on PCC. Pole 8.5mtr long complete for 25 KVA T/F including work-cutting, making holes, fixing of all types of accessories digging of pits complete in all respect, as per RESSPO drawing. nut, bolt washers would be provided by the contractor.

Erection of stay set with stay wire, stay clamp & stay insulator including with grouting of stay set by concrete of ratio 1:4:8 as per RESSPO norms before back fitting of the pits including binding, climbing, clamping, tightening and nozzeling of stay wire in all respect as per RESSPO norms Cement. Brick, ballast, sand etc would be provided by the contractor.

Concreting of PCC Pole at the time of erection of pole in 1:4:8 concrete ratio from bottom of pole to ground level and plinthing of supports upto 300mm above ground level by using cement, sand & coarse aggregate in ratio 1:4:8 as per RESSPO drawing with watering/curing properly upto proper setting of plinthing. All matrial would be provided by the contractor.

Earthing of each PCC Poles of the line is to be done by inserting the MS earth rod (1800x20mm) into soil by hammering and properly fastning with GI wire to each support by nut & bolt. Earthing rod must be 0.15Mtr.above from the plinth of the support. All type nut & bolt would be given by the contractor.

Mounting of transformers on double pole and laying of cable jumpering and making all HT/LT connections complete work in all respect.

Laying of LT XLPE cable (3X70) sq.mm from transformer to L.T Line.

Laying of ACSR Weasel Conductor for jumpering.

Fixing of 11KV TPMO

Fixing of distribution box on pole including proper clamping.

Laying of AB cable (3x50+1x35+1x16 sqmm)

Fabrication and Installation of 11 KV fuse set on midway 11 KV double pole structure with mention material As- MS channel 100x50x2028 mm, Iron strip-50x5x305 mm, fuse wire and holding clamps etc. complete work in all respect all required materials provided by contractor on his own cost.

Providing and fixing of holding clamps for S/S with bolts & Nuts

Providing and fixing of T-off Clamp

Providing and fixing of Stone Pad

Providing and fixing of danger board

Providing and fixing of barbed wire

Providing and fixing of LUGS of suitable size (70 sqmm.)

Providing and fixing of Stay Insulator

Providing and fixing of Piercing connector

Providing and fixing of I Hook with suspension clamp

Providing and fixing of Dead end clamp

Safe carriage of received back 10 KVA T/F from site to Store Centre-Pilibhit after opening and dismantaling all connections and descend of 10 KVA T/F from PCC pole including loading, unloading at both ends and proper stacking at safe site under EDD-Pilibhit.

Safe carriage of received back 16 KVA T/F from site to Store Centre-Pilibhit after opening and dismantaling all connections and descend of 16 KVA T/F from PCC pole including loading, unloading at both ends and proper stacking at safe site under EDD-Pilibhit.

M/S HINA ELECTRICALS

ASTHA TRADERS