Construction of Tehsil office building at Paonta Sahib Distt Sirmour H.P.

Amount

Excavation in earth work in foundation and trenches in all kinds and classification of soils viz, pick work, pick jumper work, jumper work, blasting work and hard blasting work saturated soils including chiselling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift upto any depth stacking the excavated soil upto any leads and lifts clear from the edge of excavation and then returning the stacked soil in any thickness of layers when required into plinths, sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as specified dumping place as per the direction of Engineer-In Charge.

Filling in plinth with approved sand under floors and plinth including watering, ramming, consolidating and dressing complete including entire carriage of material in all leads and lifts as per the direction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm (Three decimal fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete work including carriage of material within all leads and lifts and other incidential.

Foundations, footings, bases of columns and mass concrete

In flat surfaces such as soffits of suspended floors,roofs,landing and the like floor upto any thickness in all floor level

Columns,pillars,posts and struts, square,rectangular or polygonal in Plan

Stair cases with slopping or stepped soffits excluding landing

Beams, cantilevers,girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1.0 metres in depth in all heihts from floor

Slopping or battering surface including floded plates where inclination to horizontial plane does not exceed 30 degree

Edges of slabs & breaks in floors & walls under 20 centimetres wide

Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (One cement: six sand: twelve graded crushed stone aggregate 40mm (forty millimetre) nominal size) and curing complete but excluding cost of from work in foundation and plinth including carriage of materials within all leads and lifts and other incidentals.

Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (One cement: four sand: eight graded crushed stone aggregate 40mm (forty millimetre) nominal size) and curing complete but excluding cost of from work in foundation and plinth including carriage of materials within all leads and lifts and other incidentals.

Providing and laying cement concrete work 1:1.5:3 (one cement : one and half sand : three graded crushed stone aggregate 20mm (twenty millimetre) nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work including carriage of material within all leads and lifts In:-

Foundation footings, bases of columns and the like and mass concrete

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level

Stair cases ( except spiral stair case ) excluding landing but including preparing of the surface and finishing of nosing upto floor two level

Columns,pillars, posts and strutts upto floor two level

Providing and laying cement concrete 1:2:4 ( One cement:two sand : four graded stoneaggregate 20mm (twenty millimetre) nominal size )reinforced concrete chajja not exceeding 10 (ten) centimetre thickness upto all floor level including finishing the exposed surface with cement mortar 1:3 ( one cement : three sand ) to give a smooth and even surface centring/ form work and curing complete excluding the cost of reinforcement including entire carriage of material within all leads, lifts and other incidentals.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete in all heights including cost of binding wire and entire carriage of material within all leads and lifts and other incidentials.

Second class brick work using common burnt clay building bricks in super structure in cement mortar 1:6 (one cement : six sand) in foundation and plinth including entire carriage of material within all leads and lifts and other incidentals.

Second class brick work using common burnt clay building bricks in super structure above plinth level in cement mortar 1:6 (one cement : six sand) upto all floor level including entire carriage of material within all leads and lifts and other incidentals.

Second class half brick masonry common burnt clay building bricks in cement mortar 1:4 (one cement : four sand) in foundation and plinth including entire carriage of material within all leads and lifts and other incidentals.

Second class half brick masonry common burnt clay building bricks in cement mortar 1:4 (one cement : four sand) above plinth level upto all floor level including entire carriage of material within all leads and lifts and other incidentals.

Boulder filling with hard stone of approved quality dry hand packed tightly under floor including carriage of material within all leads and lifts and other incidentals .

Providing and fixing 75mm x 65mm (seventy five millimetre into sixty five millimetre) rounded hand rail of Ist class deodar wood in stright length complete sunk for mild steel flat 40x6mm (forty into six millimetre) size welded to balusters ( Mild steel flat shall be masured & paid for separately ) including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing 100mm (one hundred millimetre size bright finished brass floor door stopper with rubber cushion screws etcetra to suit shutters thickness complete including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 250mm (two hundred fifty millimetre) size bright finished hard drawn hooks and eyes with necessary screws including entire carriage of material within all leads and lifts.

Providing and fixing 50mm (fifty millimetre) diametre mild steel hollow pipe hand rail slip resistant with round ends at two level that is at 75cm (seventy five centimetre) and 90cm (ninety centimetre)height welded to 25mm dia M.S. (twenty five millimetre diametre)hollow pipes which in turn shouldbe welded to the ballusters extended 30cm (thirty centimetre) beyond the top and bottom of the ramp as per the details including balusters of 50mm dia (fifty centimetre diametre) of mild steel hollow pipe embedded in cement concrete 600mm C/C (six hundred millimetre centre to centre) with25mm dia M.S. (twenty five millimetre diametre mild steel) hollow pipe moulded to shapes including entire carriage of material within all leads and lifts. .

Providing and fixing grab bars 600mm x 40mm (six hundred millimetre into forty millimetre) size in handicapped toilets two number each chromium plated 40mm dia (forty millimetre diametre) steel pipe at 78cm (seventy eight centimetre) height with mild steel plates as per detail at the position of the seat and wash basin including entire carriage of material within all leads and lifts. .

Providing and fixing anodized aluminium work for doors, windows,ventilators and partitionswith extruded built up standard tubular & other sections of approved make conforming to IS 733 & IS 1285 anodized transparent or dyed to required shade according to IS 1868. ( Minimum anodic coating of grade AC 15 )fixed with raw plugs and screws or with fixing clips, or with expension hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with requiredPVC/Neoprene felt etcetra Aluminium sections shall smooth,rustfree,stright,mitred and jointed mechan--cially where ever required including cleast angle,aluminium,snap beading for glazing/panelling chromium plated brass stainless steel screws including entire carriage of material within all leads and lifts and as per architectural drawing and the direction of the Engineer-in-Charge.

For doors,windows and ventilators and glazing partitions frame

For shutters of doors, windows and Ventilators and making provision for fixing of fittings whereever required including the cost of PVC/Neoprene gaskets as required ( fitting and glazing/Panelling shall be paid for separately )

Providing and fixing glazing in aluminium door,window,ventilators shutters & partitionsetc. with PVC/neopprene gasket etc. complete as per the architectural drawings & the direction of Engineer-in-Charge ( Cost of aluminium snap beading shall be paid for separately ) glazing with glass pans of 4mm (forty millimetre)thickness ( weight not less than 10.00 Kg (ten kilogramme) per square metre) including entire carriage of material within all leads and lifts.

Providing and fixing glazing in aluminium door,window,ventilators shutters and patitions etc.with PVC/neopprene gasket etcetra complete as per the architectural drawings and the direction of Engineer-in-Charge ( Cost of aluminium snap beading shall be paid for separately ) glazing with glass pans of 6 mm (six millimetre) thickness ( weight not less than 13.75 Kg (thirteen point seven five kilogramme per square metre ) including entire carriage of material within all leads and lifts.

Providing and fixing 12mm (twelve millimetre) thick prelaminated board both side bwp phenol bounded ( bothside )grade particle board in matt finish ISI marked IS No. 12823 as per approved shade of Kitvista of Kitply or its equivelent in aluminium door,windows, ventilators shutter and partitions etc. with PVC/Neoprene gasket etc.complete as per the Architectural drawings ( Cost of snap beeding shall be paid in basic items)and as per the direction of the Engineer-in-Charge including entire carriage of material within all leads and lifts.

Providing and fixing 12mm (twelve millimetre)thick prelaminated board both side bwp phenol bounded (One side )grade particle board in matt finish ISI marked IS No. 12823 as per approved shade of Kitvista of Kitply or its equivelent & inside of shutters finished with aluminium sheet one mm thick in aluminium doors, windows,ventilators shutter and partitions etc. with PVC/Neoprene gasket etcetra complete as per the Architectural drawings including entire carriage of material within all leads and lifts. ( Cost of snap beeding shall be paid in basic items ).The panel shall be as per the direction of the Engineer-in-Charge.

Providing and fixing Dia table of 19mm (nineteen millimetre) thick water proof termite resistent commerical boardof Uniply/Greenply /Kitply of its equivelent ISI marked IS No.1659 cabinet size 1.00 x 0.675 x 0.45 mtr (one point zero into zero point six seven five into zero point four five metre) deep with shutter and drawers having on shelves of 19mm (nineteen millimetre) thick board and all sides of the cabinet of 19mm (nineteen millimetre) thick board,back side and bottom of cabinet shall be 8mm (eight millimetre) ply.The table tops shall be of 25mm (twenty five millimetre) thick water proof termite resistent commerical board. The vertical portion of the table towards courtside shall be finished with 4mm (four millimetre) thick teak ply to be matched with the shade of panelled as per detail Architectural drawing. The table top and other visible portions of commerical board ISI marked IS No.1659 of green ply/Kitply or its equivalent towards sitting side shall be finished with 1mm thick limination of approved shade except leg space is toe polished. All visible cut portion of commericalboard shall be finished 6 to 8mm (six to eight millimetre) thick hard wood edging/lipping polished with natural shade. The cabinet from all around shall be fixed with 19x6mm (nineteen into six millimetre) thick hard wood edging complete with piano hinges. PTMT handles of prayag polymers of its equivelent with steel screws.knobs,magnetic catchers and mortice locks/Godrej almirah type locks and necessary screws, nails and fevicol etc. complete as per Archetectural drawing including entire carriage of material within all leads and lifts.

Providing and fixing stainless steel wire mesh shutters in aluminium doors,windows,ventilatorsshutters and partitions etcetra with PVC neoprene gasket etcetra complete as per the Architectural drawing and as per direction of Engineer-in-Charge including entire carriage of material within all leads and lifts. (Cost of snap beeding shall be paid in basic items).

Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including carriage of material within all leads and lifts and other incidentals.

300x16mm ( three hundred into sixteen millimetre) size.

250x16mm( two hundred fifty into sixteen millimetre) size.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc complete including carriage of material within all leads, lifts and other incidentals.

250x10mm (two hundred into ten millimetre) size.

150x10mm (one hundred into ten millimetre) size.

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete including carriage of material within all leads and lifts and other incidentals. 100mm (one hundred millimetre) size.

Providing and laying automatic vibro hydraulically compressed 300x300x25mm (three hundred into three hundred into twenty five millimetre) size polished terrazo tiles ISI markedNo. 1237 in 70% white, 30% grey cement ratio. The Ratio of chips shall be 55 % (fifty five percent) white and 15 % (fifteen percent) of each maroon, yellow & dark shade laid over a bed of 25mm average thickness of cement mortar 1:6 ( onecement : six sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying red mandana stone/red sand stone slab flooring 40mm (forty millimetre) average thickness on 20mm (twenty millimetre) average thick base of cement mertar 1:4 (one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying 25mm (twenty five millimetre) thick Kota stone slab flooring 55cm x 55cm (fifty five centimetre intominimum fifty five centimetre) size having one shade only over 20mm (twenty millimetre) average thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of stone slab including rubbing and polish finish complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying 5.5mm (five point five millimetre) thick spartic ceremic tile flooring 300mmx300mm( three hundred millimetre into three hundred millimetre) size in tread of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement:three sand) finished with flush pointing in white flush pointing in white cement including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying marble work (Table rubbed and polished ) in flooring 20mm (twenty millimetre) thick basein cement mortar 1:3 ( one cement : three sand ) including jointing with cement mortar 1:2 ( One white cement : 2 marble dust ) with an admixure of pigment to match the shade of the marble. 20mm thick Baroda Green marble slab and shall have semi round nosing including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying heavy duty precast cement concrete inter locking paver block 7.5 cm (seven point five centimetre) thick made with vibration technology in PVC/Fiber moulder pre-polished of NTC ISI marked IS No. 15659 or its equilvent of approved shade over sub base of concrete with 25mm (twenty five millimetre) thick average thickness of cement mortar 1:4 ( One cement : four sand ) laid over and jointed with neat cement slurrymixed with pigment to match the shade of blocks including curing rubbing and polishing complete ( Sub-base concrete floor to be paid for separately ) including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying 25mm (twenty five millimetre) thick Kota stone slab in risers of steps,skirting,dado and pillars having one shadeonly over 12mm ( average ) thick base of cement mortar 1: 3 ( One cement : three sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of stone slab including rubbing and polish finish complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying automatic vibro hydraulically compressed 300x300x25mm (three hundred into three hundred into twenty five millimetre) thick polished terrazo tiles ISI markedNo. 1237 in 70% (seventy percent) white and 30% (thirty percent) grey cement ratio. The Ratio of chips shall be 55% (fifty percent) white and 15 % (fifteen percent) of eachmaroon, yellow and dark shade laid over a bed of 25mm (twenty five millimetre) average thickness of cement mortar 1:6 ( One cement : six sand ) jointed with neat cement slurry mixed with pigment to match the shade of tilesincluding rubbing and polishing complete in skirting and dedo including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing Jaiselmer white marble bands 7.5 cm (seven point five centimetre) wide and 25mm (twenty five millimetre) thick in flooring on 20mm (twenty millimetre) thick base of cement mortar 1 : 4 ( one cement : four sand )including jointing with grey cementslurry mixed with pigment to match the shade of stone rubbing and polishing complete including entire carriage of material within all leads, lifts and other incidentals.

Extra for providing and fixing glass strips in joint trezzo floors 40mm (forty millimetre) wide and 4mm (four millimetre) thick including entire carraige of material within all leads, lifts and other incidentals.

Providing and fixing 0.60mm ( Zero point sixty milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified poliyster (RNP) organic coating of 20 (twenty ) microns over 5 ( five ) microns primer coating to black coat of polyster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm ( six milimetres ) with prepainted G.I limpet and bitumen washers complete with all accesories as required as per direction of Engineer-in-Charge.

Providing and fixing ridges or hips overall 60 cm (sixty centimetre0 with 0.60mm (zero decimal six zero millimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) micron over 5 (five) micron primer coating to black coat of polyster of 5 (five0 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction and entire satisfaction of the Engineer-in-charge.

Providing and fixing valley overall 60 cm (sixty centimetre ) with 0.60mm (zero decimal six zero millimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) micron over 5 (five) micron primer coating to black coat of polyster of 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction and entire satisfaction of the Engineer-in-charge.

Providing and fixing 0.80mm (zero point eight zero millimetre) thick, 30cm (thirty centimetre) wide and minimum 90cm (ninety centimetre)overall semicircular plain galvanised iron sheet gutterwith iron bracket 40x5mm (forty into five millimetre) size with bolts, nuts and washers etcetra including making necessary connections with rain water pipes complete as per approved design and satisfaction of the Engineer-in-Charge including entire carraige of material within all leads, lifts and other incidentals.

Providing and fixing mild steel BP sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board, facia, soffits, ceiling including cutting, fixing and welding to to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid for separately) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing on wall face 75mm dia (seventy five millimetre diametre) size PVC rain water pipe/ventilating pipes of 2.2mm (two poin two millimetre) thick supreme or its equivelent conforming to IS No. 13592-92, of fire resistent,chemical resistent and should be able to withstand tempature upto 60* C (sixty degree centigrate) and fitting the joints all conform to IS No. 14735-99 and shall be jointed to each other by a rubber ring or push fit jointing system with sealing ring and rubber lubricant adhesive Type-A and material shall be accompanied by test certificate certifying the qualityquality of materials IS No. diamension and warrenty including carriage of material within all leads, lifts and other incidentals.

Providing and fixing on wall face 110mm dia (one hundred ten diametre) size PVC waiste water pipe/ventilating pipes of 2.7mm (two point seven millimetre) thick supreme or its equivelent conforming to IS No. 13592-92, of fire resistent,chemical resistent and should be able to withstand tempature upto 60* C (sixty degree centigrate and fitting the joints all conform to IS No. 14735-99 and shall be jointed to each other by a rubber ring or push fit jointing system with sealing ring and rubber lubricant adhesive Type-B and material shall be accompanied by test certificate certifying the qualityquality of materials IS No. diamension and warrenty including carriage of material within all leads, lifts and other incidentals.

Providing and fixing on wall face 75mm dia (seventy five millimetre diametre) and 2mm (two millimetre) thick plain bend for PVC rain water pipe/ventilating accessories forrain /waiste water pipe including filling the joints with approved adhesive Type-B and material shall be accompanied by test certificate certifying the quality of materials IS No. diamension and warrenty including carriage of material within all leads, lifts and other incidentals.

Providing and fixing on wall face 100mm dia (one hundred millimetre diametre) and 2.7mm (two point seven millimetre) thick plain bend for PVC rain water pipe/ventilating accessories forrain /waiste water pipeincluding filling the joints with approved adhesive Type-B and material shall be accompanied by test certificate certifying the quality of materials IS No. diamension and warrenty including carriage of material within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint complete upto any height including entire carriage of material within all lead, lifts and other incidentals in Beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hhips and jack rafters, purlins connected to common rafters and the like.

Steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint complete upto any height including entire carriage of material within all lead, lifts and other incidentals in gratings framed guard bars, ladders, railing, brackets and similar works.

Providing and fixing mild steel round holding down or anchor bolts with nuts and washers plates complete including entire carriage of material within all leads, lifts and other incidentals.

Applying one coat of Birla white wall care putty or Kemocare wall smoothner putty of Kamdhenu or its equivalent over plastered surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters, sand papering smooth to give final matter finish to surface complete including entire carriage of material within all leads, lifts and other incidentals.

Applying one coat of Acrylic primer or Kamdhenu primer or its equivelent of superior quality on new concrete, plastered surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matter, sand papering smooth the surface complete including entire carriage of material within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade premium emulsion of Kamdhenu paints or Apex Ultima or its equivelent of approved shade on undecorated wall surface with two coats to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter including sand papering smooth in all external plastered surfaces including entire carriage of material within all leads, lifts and other incidentals.

Wall painting with two coats with premium enamel paint Kemolite of Kamdhenu or its equivelent upto 140cm (one hundred forty centimetre)height having two number bands 5cm (five centimetre) wide each above 125 (one hundred twenty five)and 135cm (one hundred thirty five centimetre) height of approved shade as per pettern to detail on undecorated cobcrete or plastered wall surface to give give shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter including sand papering smooth including entire carriage of material within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfaces, with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter, ready mixed paint other than white including carriage of materials within all leads, lifts and other incidentals .

15mm (fifteen millimetre) cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering up to all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) upto any floor level including carriage of materials within all leads and lifts and other incidentals.

15mm (fifteen millimetre) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetres) in girth and finished even and smooth in cement mortar 1:6 ( One cement : six sand) including carriage of material within all leads, lifts and other incidentals.

Distempering ( two coats) with oil bound washable distemper of approved brand and manufacture of required shade on undectoraed wall surface to given an even shade over and including priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface from mortar dropping and other foreign matter including preparing the surface even and sand papered smooth with primer coat / distemper primer including carriage of materials within all leads and lifts and other incidentials charges.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including throughly brushing the surface free from mortar, droppings and other foreign matter and sand papered smooth including applying of putty as required for making making the surface including entire carriage of material within all leads,lifts and other incidentals.

Distempering ( two coats) with dry distemper of approved brand and manufacture of required shade on undectoraed wall surface to given an even shade over and including priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface from mortar dropping and other foreign matter including preparing the surface even and sand papered smooth with primer coat / distemper primer including carriage of materials within all leads and lifts and other incidentials charges.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed of dry brick/stone aggregate 40mm (forty millimeter) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground and carriage of materials within all leads and lifts and other incidentials charges.

Providing plinth protection 50mm (fifty millimeter) thick in cement concrete 1:3:6 (one cement : three sand : six graded crushed stone aggregate 20mm (twenty millimeter) nominal size) including carriage of materials within all leads and lifts and other incidentials charges.

Constructing course rubble hammer dressed 'U' shape drain with side wall 15x22 cm (fifteen into twenty two centimetre) size in cement mortar 1:6 (one cement : six sand) and inside plastering 1:3 (one cement : three sand) including earth work and laying 10 cm (ten centimetre) thick cement concrete in 1:5:10 (one cement : five Sand : ten graded stone aggregate 40mm (forty millimetre) nominal size and 7.5cm (seven point five centimetre) thick cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) with finishing floating coat of neat cement as per standard design and specification and curing complete including entire carriage of material within all leads, lifts and other incidentals.

Excavation in earth work in drains and channels etcetra in all kinds of classification, soils viz, pick work, pick jumper work, jumper work, blasting work and hard blasting work saturated soils including chiselling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift upto any depth, disposing the excavated soil upto any leads and lifts clear from the edge of excavation, disposed soil to neatly levelled and dressed as per the direction of Engineer-in-charge.

Providing & fixing Polythene Aluminium Polyethene(PE-AL-PE)composite pressure pipe U.V. stabilised with confirming to IS-15450-2004 for water supply including clamps at one metre spacing,cutting and making good the wall, but excluding the cost of fitting ( Internal work ) pipe exposed on walls including carriage of material within all leads, lifts and other incdentals.

1216 ( 16mm (sixteen millimetre) outside diametre pipe )

1620 ( 20mm (twenty millimetre) outside diametre pipe )

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connections, couplers and clamps with jointing testing and fitting complete including cutting and making good the wall etcetra including entire carriage of material within all leads, lifts and other incidentals.

a (i) Equal Tee:-1216 ( 16mm (sixteen millimetre) outside diametre pipe )

ii 1620 ( 20mm (twenty millimetre) outside diametre pipe )

b Reducing Tee :- 1620 x all branches.

c (i) Female branch Tee :-1216 x 1216 x 15 millimetre thread

ii 1620 x 1620 x 20 millimetre thread.

d (i) Female Elbows :-1216 x 15 millimetre thread

ii 1620 x 20 millimetre thread.

e (i) Male Thread Connection :-1216 x 15 millimetre thread

(ii) 1620 x 20 mm thread.

f (i) Female Thread Connection :- 1216 x 15 millimetre thread

(ii) 1620 x 20 millimetre thread.

g (i) Couplers :-1216

h (i) Reducers :-1620 x 1216

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings ( earth work in trenches to be measured and paid for separately)including entire carriage of material within all leads, lifts and other incidentals.

15mm (fiteen millimetre) nominal bore

20mm (twenty millimetre) nominal bore

Fixing water metre stop cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nuts,sockets, etc. cutting and making long screws, complete ( Water metre and stop cock to be measured and paid for separately including entire carriage of material within all leads, lifts and other incidentals.

15mm (fiteen millimetre) nominal bore

20mm (twenty millimetre) nominal bore

Providing and fixing PVC water storage tank of ISI 12701 marked, galvanised iron inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including entire carriage of material within all leads, lifts and other incidentals.

500 litre net capacity tank

1000 litre net capacity tank

Constructing chamber 300mm x 300mm x 500mm (three hundred millimetre into three hundred millimetre into fove hundred millimetre) inside size for stop cock with cast iron surface box 100mm x 100mm x 75mm (one hundred millimetre into one hundred millimetre into seventy five millimetre)( inside ) with hinged cover fixed in cement concrete slab 1:2:4 ( one cement:two sand:four graded stone aggregate 20mm nominal size ) 75mm (seventy five millimetre) thick foundation concrete 1:5:10 ( one cement:five sand:ten graded stone aggregate 40mm (forty millimetre) nominal size ) and inside plastering with cement mortar 1:3( One cement:three sand )finished with a floating coat of neat cement including curing complete with 100mm (one hundred millimetre) thick walls of brick masonry in cement mortar 1:5 ( One cement:five sand ) including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing on wall face PVC soil waist water pipe of supreme or its equivelent conforming to IS No. 13592-92, of fir resistent,chemical resistent and should be able to withstand temprature upto 60* C and fitting the joints all conforming to IS No. 14735-99 and shall be joined to each other by a rubber ring/push fit jointing system with a sealing ring and a rubber lubricant adhesive Type-B and material should be accompanied by a test certificate certifying the quality of materials IS No. dimension and warrenty including entire carriage of material within all leads, lifts and other incidentals.

75 mm dia (seventy five millimetre diametre) and 2.2 mm (two point two millimetre) thick size.

110mm dia (one hundred ten millimetre diametre) and 2.7 mm (two point seven millimetre) thick size .

160mm dia (one hundred sixty millimetre diametre) and 4.6mm (four point six millimetre) thick size.

Providing and fixing accessories on wall face PVC connection of soil waist water pipe of 8/4.6mm (eight obleque four point six millimetre) thick of supreme or its equivelent conforming to Indian Standard Number 13592-92, of fir resistent,chemical resistent and should be able to withstand temprature upto 60* C (sixty degree centigrate) and fitting the joints all conforming to Indian Standard number 14735-99 and shall be joined to each other by a rubber ring or push fit jointing system with a sealing ring and a rubber lubricant adhesive Type-B & material should be accompanied by a test certificate certifying the quality of materials Indian Standard Number dimension and warrenty including entire carriage of material within all leads, lifts and other incidentals.

a Plain bends :- (i) 75mm dia 2.2 mm (seventy five millimetre diametre and two point two millimetre) thick

(ii)110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(iii)160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

b Collars :- (i) 75mm dia 2.2 mm (seventy five millimetre diametre, two point two millimetre) thick

(ii) 110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(iii)160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

c PVC Off set :- (i) 110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(ii) 160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

d PVC Single branch :- (i) 110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(ii) 160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

e PVC Double branch :- (i) 110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(ii) 160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

f PVC Connection plug :- (i) 110 mm dia 2.7mm (one hundred ten millimetre diametre and two point seven millimetre) thick

(ii) 160mm dia 8/4.6mm (one hundred sixty millimetre diametre, eight obleque four point six millimetre) thick

Providing and fixing PVC Cowl for ventilating pipes for rain water pipe or soil waiste pipe 110mm dia (one hundred ten millimetre diametre) PVC Cowl of 2.7 (two point seven) thick millimetre including carriage of material within all leads, lifts and other incidentals.

Providing and fixing cast iron holder bats clamp including steel botls to sand cast iron/ cast ( Spun ) iron pipes embedded in and including cement concrete block 100mmx100mmx100mm (one hundred millimetre into one hundred millimetre into one hundred millimetre) size of 1:2:4(one cement:two sand:four graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the wall including carriage of material within all leads, lifts and other incidentals.

75mm dia. (seventy five millimetre diametre)

110 mm dia. (one hundred millimetre diametre)

160mm dia. (one hundred sixty millimetre diametre)

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting and making good the walls and floors including carriage of material within all leads, lifts and other incidentals.

75mm dia. (seventy five millimetre diametre)

110 mm dia. (one hundred millimetre diametre)

Providing and fixing Vitreous China wash down water closet ( Orrisa Pattern ) Orrisa Pan water closet Number 2071 size 58 x 44 (fifty eight into forty four)centimetre in white shade of Cera or its equivelent in General Toilets ( Earth work, bed concrete,foot rest and trap to be measured & paid for separately) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing Vitreous China wash down water closet ( European type W.C. Pan ) with intergal " P " or " S " trap including jointing the trap with soil pipe in cement mortar 1:1 ( one cement : one sand ) ( Seat & cover to be measured & paide for separately ) Anglo Indian W.C. No. 20012 of white shade of Hindware or its equilevent W.C. Pan including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 110mm dia (one hundred ten millimetre diametre) PVC " P "or"S " trap for water closet (Squatting Pan ) ISI Marked including jointing the trap with the pan & PVC pipe with approved adhesive etc. complete including carriage of material within all leads, lifts and other incidentals.

Providing and fixing in cement mortar 1:3 ( one cement : three sand ) a pair of vitreous China 250mmx 130mm x 30mm (two hundred fifty millimetre into one hundred thirty millimetre into thirty millimetre) size foot rests for long pattern squatting Pan water closet including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 10 (ten) litre net capacity first quality white shade low level flushing cistern ( with duo flushing cisern ) item No. 502 ISI marked No. 7231 of Prayag sanitary Hardware or its equvelent with a pair of cast iron or mild steel brackets complete with fitting such as lead valveness syphon 15mm (fifteen millimetre) nominal size PVC brass valve with polythene float with push button, couplings for connections with inlet, outlet and over flow pipes, 40mm dia (forty millimetre diametre) flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( Overflow pipe to be measured and paid for separately ) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing in position brass mosquito proof coupling for over flow pipe of 25mm (twenty five millimetre) nominal diametre over flow pipe to be measured and paid for separately ) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing plastic seat ( solid/Hollow type ) and cover for wash down water closet with chromium plated brass hinges and rubber buffers solid type white plastic seat and cover including carriage of material within all leads, lifts and other incidentals.

Providing and fixing first quality of white shade Vitreous China Bowl pattern flat back large Urinal No. 60002 size 430 x 260 x 350 (four hundred thirty into two hundred sixty into three hundred fifty) millimetre of Hindware or its equivelent including connection of Urinal with waste pipe by means of white lead mixed with chopped heamp ( Waiste pipe to be measured & paid for separately) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 5 (five) litre capacity first quality Vitreous China automatic flushing cistern No. 61002 of white shade of Hindware or its equivelent with a pair of cast iron or mild steel brackets complete with fitting including cast iron syphonic apparatus, mosquito proof lid, chromium plated brass unions and coupling for connection with inlet, outlet and overflow pipes including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet ( Over flow pipe to be measured and paid for separately) in all the general toilets of all floors in white shade including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 15mm (fiteen millimetre) nominal bore chromium plated brass flush pipes/ Spreaders for urinal with fitting such as unions, clamps, etcetra (all in chromium plated brass ) including cutting holes and making good the same including carriage of material within all leads, lifts and other incidentals.

Providing and fixing Vitreous China wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fitting flat back white shade No. 20004 of 580 x 400mm (five hundred eighty into four hundred millimetre) size with pedestal of Hindware or its equivalent including carriage of material within all leads, lifts and other incidentals.

Providing and fixing Vitreous China Pedestal for wash basin complete recessed at the back for reception of pipes and fittings including carriage of material within all leads, lifts and other incidentals.

Providing and fixing stainless steel kitchen sink of approved standard ISI marked No. 1022-XD of 470x420mm (four hundred seventy into four hundred twenty millimetre) size with bowl depth 178mm (one hundred seventy eight millimetre) of Prayag polymers or its equivelent with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 32mm dia (thirty two millimetre diametr) chromium plated brass Chain 50mm (fifty millimetre)long with rubber plug for sink or wash basin including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 32mm dia (thirty two millimetre diametre) mild iron union of superoir quality for wash basin or sink including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 32mm dia (thirty two millimetre diametre) chromium plated brass waste of superior quality for wash basin or sink including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 32mm dia (thirty two millimetre diametre) chromium plated brass " S " trap of superior quality for wash basin or sink including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 100mm (one hundrd millimetre) size sand cast iron grating of superior quality for gully, floor or Nahni Trap including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 600mm x 450mm (six hundred millimetre into four hundred fifty millimetre) size bevelled edge mirrior of superior glass mounted on 6mm (six millimetre) thick asbestos cement sheet or plywood sheet and fixed to wooden plugs with chromium plated brass screws and washers including carriage of material within all leads, lifts and other incidentals.

Providing and fixing chromium plated brass towel rail of superior quality with chromium plated brass brackets fixed to wooden plugs with chromium plated brass screws 750mm x 20mm (seven hundred fifty into twenty millimetre) size including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 600mm x 120mm (six hundred millimetre into one hundred twenty millimetre) size glass shelf of superior quality with chromium plated brass brackets and guard rail complete fixed to wooden plugs with chromium plated brass screws complete including carriage of material within all leads, lifts and other incidentals.

Providing and fixing chromium plated brass toilet paper holder of superior quality including carriage of material within all leads, lifts and other incidentals.

Pand fixing liquid soap glass container of superior quality with chromium plated brass lid and brackets fixed to wooden plugs with chromium plated brass screws including carriage of material within all leads, lifts and other incidentals.

Providing and fixing chromium plated brass soap dish of superior quality with chromium plated brass brackets fixed to wooden cleats with chromium plated brass screws including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 15mm dia (fifteen millimetre diametre)brass bib tap of superior quality including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 15mm dia (fifteen millimetre diametre) chromium plated brass pillar tap with capstan head of superior quality including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 15mm dia (fifteen millimetre diametre) chromium plated stop cock of superior quality including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 15mm dia (fifteen millimetre diametre) chromium plated brass angle valve of superior quality without nuts and pipe including carriage of material within all leads, lifts and other incidentals.

Constructing manhole with reinforcement cement concrete top slab in 1:2:4 mix in one cement : two sand : four crushed stone aggregate 20mm (twenty millimetre) size, foundation concrete 1:4:8 (One cement : four sand : eight crushed stone aggregate 40mm (forty millimetre) nominal size with inside plastering 15mm (fifteen millimetre) thick in cement mortar 1:3 (one cement : three sand) finished with afloating coat of neat cement and making channnels in cement concrete 1:2:4 mix (one cement : two sand ; four crushed stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curing and testing, inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) size and 500mm (five hundred millimetre) deep with frame ) light duty single seat pattern-I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions having total weight of cover and frame to be not less than 38 kg. (thirty eight kilogramme) (weight of cover 23kg (twenty three kilogramme) and weight of frame 15 kg. (fifteen kilogramme) with 200mm (two hundred millimetre) thick walls of second class common burnt clay building bricks in cement mortar 1:3 (one cement : three sand) including entire carriage of material within all leads, lifts and other incidentals.

Second class brick work using common burnt clay building bricks in cement mortar 1:4 (one cement : four sand) in foundation and plinth including entire carriage of material within all leads and lifts and other incidentals.

Providing form work with steel plates 3.15mm (Three decimal fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete work in vertical surfaces such as walls (any thickness) partition and the like including buttresses, plinth and string courses and the like including carriage of material within all leads and lifts and other incidentals.

Providing and laying 50mm (fifty milimetre) thick cement concrete flooring 1:2:4 (one cement :two sand:four graded crushed stone aggregate 20mm (twenty milimetre) nominal size laid in one layer finished with a floating coat of neat cement including carriage of material within all leads, lifts and other incidentals.

20mm (twenty millimetre) cement plaster in two coats, backing coat 10mm (ten millimetre) and finishing coat 10mm (ten millimetre) on fair side of brick/concrete/stone walls for interior plastering up to all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:4 (one cement : four sand) upto any floor level including carriage of materials within all leads and lifts and other incidentals.

Supplying and fixing cast iron cover with out frame for main hole for 500mm (five hundred millimetre) internal diametre (medium duty) of superior quality, the weight of cover should be not less than 58 kg. (fifty eight kilogramme) including carriage of material within all leads, lifts and other incidentals.

Supplying and stacking at site of work gradded/ broken /crushed stone aggregate 40mm (forty millimetre) nominal size of approved hard stone free from disintegrated pieces deleterious and organic matter including entire carriage of material within all leads and lifts and other incidentals.

Supplying and stacking at site of work coarse sand free of dust, dirt and other organic matter including carriage of material within all leads and lifts and other incidental charges.

Providing and fixing on wall face PVC (D-Plast) 100mm (one hundred millimetre) diametre rain water pipes of working pressure not less than 4.5kg (four point five kilogramme) per square metre including filling the joints with approved adhesive complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing PVC vent pipe 100/110mm (one hundred obleque one hundred ten millimetre) diametre for cowl of septic tank complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and laying cement concrete work 1:1.5:3 (one cement : one and half sand : three graded crushed stone aggregate 20mm (twenty millimetre) nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in walls all thicknesses, attached pillasters, buttresses, plinth and string courses etcetra upto all floor level including carriage of material within all leads, lifts and other incidentals.

Lal Singh Chauhan Contractor