Construction of Remaining work of Unfinished Houses of Kaat Bangla Slum in Dehradun under Nagar Nigam Dehradun.

Amount

Half brick work with bricks of 1st class in superstructure in cement mortar 1 : 4 ( 1 cement : 4 coarse sand ).

6 to 10 mm thick internal plaster with 1:4 cement & fine sand mortar with tucking of surface including supply of all materials, labour, T&P etc required for proper completion of the work.

12 mm thick external plaster with 1:6 cement & fine sand mortar on smooth surface including supply of all materials, labour, T&P etc required for proper completion of the work.

15 mm thick interrnal cement plaster with 1:6 cement & coarse sand mortar on smooth surface including supply of all materials, labour, T&P etc required for proper completion of the work.

Sand filling with watering, ramming including supply of all materials, labour, T&P etc. complete.

P/L C.C. in found. & plinth, bases of columns etc. (a) 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

4 cm thick CC 1:2:4 plain cement concrete floor with cement, coarse sand and 2 cm gauge stone ballast laid in panels, finished with 3 mm thick floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overtapping mortar at the point of the panels if any and giving them a uniform finish including supplyo of all materials, labour, T&P etc required for proper completion of the work.( Rate as per S. N. 367)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)..

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc

S/F of 30 mm thick ISI mark commercial flush door shutter including supply of all materials, labour, T&P etc required for proper completion of the work.

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. ISI marked hinges - 125X65X2.12 mm size.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : ISI marked oxidised tower bolts - 200X10 mm size.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : ISI marked oxidised M.S. handle - 125 mm size.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : ISI marked oxidised M.S. aldrop.

Colour washing three coats including all materials, labour, T&P etc required for proper ompletion of the work.

Finishing wall with water proofing cement paint of approved quality on new work with three coats to given even shade including all materials, labour, T&P etc required for proper ompletion of the work.

P/F white glazed tiles including binding for proper completion of the work.

P/F marble stone slab in kitchen counter including binding for proper completion of the work.

P/F 4 mm thick glass panes including binding for proper completion of the work.

Synthetic enemal paint two coat in new wood or iron work including binding for proper completion of the work.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

P/F of M.S. angle iron nosing of 35X35X4 mm size in steps including binding for proper completion of the work.

S/F 256 nos. PVC water storage tank of 500 litre capacity of approved quality SINTEX including all materials, labour, T&P etc required for proper ompletion of the work.

P/F GI class B pipe with Gi fittings & clamps including all materials, labour, T&P etc required for proper ompletion of the work.( internal work) 25 MM

P/F GI class B pipe with Gi fittings & clamps including all materials, labour, T&P etc required for proper ompletion of the work.( internal work) 20 mm

P/F GI class B pipe with Gi fittings & clamps including all materials, labour, T&P etc required for proper ompletion of the work.( internal work) 15 mm

P/F white vitreous chinaware indian pattern ORRISA pan of 580 mm size with 100 mm sand cast P or S trap, 10 ltr PVC 10W level cistern & steel long bend including all materials, labour, T&P etc required for proper ompletion of the work.( internal work)

P/F steel sink of 610X460X230 mm size with RS or CI brackets CP brass chain with union 15 mm PVC connections1 mm CP brass pillar cock & 15 mm CP brass angular stop cock, 32 mm CP brass wate pipe including all materials, labour, T&P etc required for proper ompletion of the work.

Supplying & fixing of CP brass bib cock heavy quality short body half inch dia.

P/F 20 mm dia gun metal gate valve with white superior quality including all materials, labour, T&P etc required for proper ompletion of the work.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single pushfit Coupler 110 mm

(Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend PVC pipe bend.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Gully trap.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors- 100 mm inlet and 75 mm outlet (Sand Cast Iron S&S as per IS- 1729)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Looking mirror.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m. - All kinds of soil.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) in footing excluding supply of of reinforcement but including fixing and binding the same, excluding centering & shuttering etc required for proper completion of the work.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Fixing and removing of shuttering centering including supply of all materials, labour, t&P etc required for proper completion of the work.

Providing and laying in position specified grade of reinforced cement concrete in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) for columns from G.F. to Floor IV excluding supply of of reinforcement but including fixing and binding the same and excluding centering & shuttering etc required for proper completion of the work.

As above but for slab beams of G.F.

As above but for projection of windows, shelvs of cuboard etc.

230 mm thick brick work with bricks of 1st class in superstructure in cement mortar 1 : 6 ( 1 cement : 6 coarse sand ).

Tor steel work in plain work such as in RCC work brought to required shape as necessary including binding for proper completion of the work.

25 mm thick CC 1:2:4 on aprin with materials, labour, T&P etc complete. (494.04*0.025=12.35)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars in UG Tank , Septic Tank

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended Floor ,roofs,landings,balconies and access platform

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm drynbrick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 m Excavation for roadwork in soil with hydraulic excavator of 0.9 Cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3

Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, in breast walls, retaining walls, parapets, scuppers, etc. including supply of all material, labour, T&P and royaltiies etc. complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 of MORD Specifiction

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408. Using naturally occuring gravel

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 (The reinforcement steel shall be procured from original (primary) steel producers as per clause no. 2011.3.1 of MORD specifications (First revision'2014) and IS 1786:2008 clause no. 1.6)

Providing and laying in position specified grade of cement concrete in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) excluding supply of of reinforcement but including fixing and binding the same and excluding centering & shuttering etc required for proper completion of the work.

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer

Making C.C. drain along road.

ELECTRIFICATION WORK

S/F of MCB distribution box SPN MCB DB 6 way.

Supply & wiring of sub main with 3X1.5 SQMM PVC insulated condutor cable in 25 mm dia conduit from distribution box to switch board.

Supply & wiring of sub main with 3X2.5 SQMM PVC insulated copper condutor cable in 25 mm dia conduit from distribution box to power point.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group A (Light )

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 5/6 amps switch (Plug point box)

Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required. seprate plug point

Supply & fixing of fan hook fabricated from M.S. rod for ceiling fan.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.