Providing G20 to G26 Shops Arrangement at Anna Bus Stand Thoothukudi Corporation

Amount

Earthwork excavation and depositing on bank with an initial lead and lift in all classes of soil including the cost and conveyance of all materials and all labour charges etc. complete asper standard speicfication.

Supply and filling of well gravel from approved quarry including the cost and conveyance of all materials and all labour charges etc. complete asper standard speicfication.

Plain cement concrete 1:4:8 mix using 40mm ISS size HBG metal from approved quarry including the cost and conveyance of all materials and all labour charges etc. complete asper standard speicfication.

Providing steel centering for sides and soffits of cement concrete works including necessary arrangements With props , With all cost and conveyance of materials and lab our at site ect ., Complete as per standard specfication.(lintel beam)

Reinforced cement concrete of M20 mix using 20m ISS HBG metal from aproved quarry and all cost of materials for all RCC works with all cost and conveneyance of materials and labour charges etc., complete complying with standard specification (lintel beam)

Supplying fabricating and placing in position of R.T.S rods including cutting, bending, straightening of rods and tying the reinforcement with necessary binding wire including all cost and conveneyance of materials to site and all labour cost etc., complete complying with standard specification.

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9" X 43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification -

Solid Block Masontry work 1:5 ( one cement Five sand) mix using well burnt country bricks of size (12” x 4 ¼” x8” )from approved quarry including all cost and conveyance of materials to site and all labours charges etc., complete as per standard specification.

Supplying of Materials structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Providing Painting two coats with ready mixed synthetic enamel paint to new iron work using best and approved colour including all the cost and conveyance of materials to site and all labour charges etc. complete as per standard specification.

Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing of rolling shutters shall be pull and push type (Manual operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Painting two coats with approved interior and exterior emulsion paint over cement plastered wall surfaces, ceiling and other new surfaces including Cleaning preparing the surface and curing etc., complete as per standard specification

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with with metal box and 6A 1way modular Switch in flush with wall with suitable modular front plate cover for making good of the concealed portion for PVC concealed light point /fan point for Electronic Regulator) (5 Points Per Coil)

Supply and fixing of 5Amps (3 pin an 2 pin ) combined flush type waqll socket with control switches concealed in suitable TW Box covered with 3mm thick hylem sheet

Supply and fixing of 5A / 15 A 3 Pin combined flush type wall socket with 15A flush type switch concealed in suitable MS Box in flush with wall and covered with 3 mm thick hylem sheet

Supply and fixing of 20 Amps MCB

Supply and fixing of 4way single pole and neutral MCB sheet steel enclosure with IP 42 protection with 1No 32 Amps DP MCB as incoming and 6 Nos 6 Amps to 32 Amps SPMCB as outgoing inflush with wall and making good of the concealed portion with earth connection only. (The MCB DB and MCB's should be of Legrand/Hager make)

Supply and fixing of Miniature Circuit breakers 240 V / 415V 50HZ - AC supply suitable for both lighting and motor circuits Single Pole 6A to 32A, 10KA including all charges etc, complete as per standard specification.

Supply and fixing of 40 A FP MCB Isolators including all charges etc, complete as per standard specification

Supply and fixing of 25 Amps 30 MA DP RCCB / ELCB including all charges etc, complete as per standard specification.

Supply and clamping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

SHASHA ENGINEERING AND CONSTRUCTIONS