ADDN/ALTN CUM SPL REPAIRS OF OTM ACCN AT 42 INF BDE UNDER GE (MES) DEHRADUN

Amount

Taking down carefully copper/Aluminium point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-In-Charge.

M&L in Replacement for existing point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including continuous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the foll. (Note: Colour code shall be maintained as per IE rule)

(a) One light point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) All as per item No. 2 above but one 3 pin socket outlet 15 Amp independent ' with cable 2.5 Sq. mm Size 'with earth continuiy conductor of size 2.5 Sq mm

M&L for new point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule)

(a) One light point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) All as per item No. 2 above but one 3 pin socket outlet 15 Amp independent ' with cable 2.5 Sq. mm Size 'with earth continuiy conductor of size 2.5 Sq mm

S&F switch piano flush, button type 5 Amp SP 240 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 240 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 pin 5 amp 240 V AC complete all as specified & directed.

S&F socket outlet 2 in1 ,3 pin 5 Amp and 15 Amp flush type complete al as specified.

S&F stepped type electronic fan regulator flush type socket type 120 Watt on the existing phenolic laminated sheet etc as required.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 240 V AC.

S&F lamp holder PVC/polycarbonate type with back plate suitable for B-22 type 12 watt bulb 240 V AC.

M&L in replacement sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings with chasing/ cutting and Insulated unsheathed FRLS-H cable copper conductor multistranded of size 6.0 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed including taking down old sub main wiring .

Supply & fixingand Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management including Provision of MCCB 63 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge (Note :- MCB/ MCCB shall be measured and paid separately)

S&F in replacement sheet metal enclosures 240 volt with 200 amps rated copper bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge, including taking down old unserviceable DBs. (MCBs shall be measured and paid separately).

S&F MCB SPN 240 Volt 10 KA 40-63 Amp 'B' series conforming to ISI marked complete all as specified & directed .

S&F MCB SP and 240 volt 10 KA 6-32 Amp 'B' series conforming to ISI marked all as specified and directed .

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

Supply & fix in replacement of LED light fitting 1200 mm length minimum 2000-2200 Lumen, system efficacy not less than 100lm/watt with 2.5 KV surge protection electronic driver aluminium extruded/Polycarbonate body suitable for surface, wall or ceiling mounting with acessories like both side end cap, driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed. Make - (a) Hallonix HLB-03-22-CW (b) PHILIPS- BN 021 LED22S 6500 PSU GR, (c) Havells Nicolaus Glamtube 20 W 6500 K - LHEWAJPGPV1B020.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver,holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.Make:-1) Havells - VENUSNEO2X2PLR36WLED865G2 ( 2) Crompton - LCTLRN-36-FO-CDL, WW, TL) Wipro - LM10-451-XXX-40-G2

S & F high efficiency LED bulbs 1 X 12 watt B-22 complete all as specified and directed.

S&F Bed side lamp fitting 360 degree flexible twisting/rotating LED type of capacity 5-6 watts rechargeable type including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make - Philips/Havells/Wipro/Syska

S&F ceiling fans complete with blades ,down rods with controlling/connected accessories, 230 V ,1200mm sweep. Min air delivery 225 CMM with Five Star Rated with Brushless Direct Current(BLDC) Motor. Note:(1) Rate for hanging arrangements, taking down/dismantling of old ceiling fan, writing MES no and depositing at GE Dehradun store yard to ceiling fan at own cost deemed to be included in quoted rate of Ceiling Fan deemed to be included. Make:- (1) Havells - Bianca BLDC, (2) Crompton - ENERGION HS 1200mm. (3) Atomberg Erica.

Supply & fix exhaust fans steel body AC single phase 230 V of size 300 mm sweep with blades ,frame and louvers.M&L for making Holes of suitable size and making good disturbed surface inluding connecting testing complete all as directed by Eng-in-charge .Make:-1) Bajaj Model No -MAXX AIR 300mm. (2) Crompton Model No-.TRANS AIR 300mm. (3) Havells Model No - VENTIL AIR DB 300mm

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed.

Supply and fix electric water heater storage type steel body with mettalic inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, Fixing bolts, stainless steel braided connection piece 450 mm long etc.

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 36/40 watt with efficiency 110 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including GI brackete made out of 40 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed.Make:-(1) Philips Cat Part No -Smart Bright 45W Street Light (Cool White, Grey) ( 2) Crompton Model No-.LSTS-40-CDL-M(Astra Neo( 3) Wipro Cat Part No - LR02-451-XXX-57-G1

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core.

M&L for Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of underground cable, foundation of pole and getting out in soft/loose soil complete all as specified and directed.

M&L for Returning, filling in excavated soil in trenches including spreading, levelling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

M&L for Removing of excavated soil to a distance n. exc. 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed.

M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed.

Suppy and fix GI pipe 40 mm light grade galvanised with all fitting laid in trenches for protection of cable

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete as directed and specified.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete as directed and specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.complete as directed and specified.

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of mud brick work in mud mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. Note :- Mud obtained from demolition of mud brick wall shall be disposed off and levelled at a distance exc 500m but n.exc 1.50 Km as shown and directed by Engineer in charge. Rate for the same deemed to be included in the quoted rate.

Dismantling timber scantling 40 sq cm and over in section , in any position for unframed /framed work complete all as specified and directed by Engr-in-Charge

Dismantling of steel/galvalume sheets of any description (corrugated, semi corrugated, etc.)sheets in roof coverings complete all as specified and directed by Engr-in-Charge

Dismantling Mild Steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

Dismantling of asbestos cement sheets of any description (corrugated, semicorrugated, etc.)sheets in roof coverings complete all as specified and directed by Engr-in-Charge

Dismantling wall and ceiling board,of any description complete all as specified and directed by Engr-in-Charge

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs complete all as specified and directed.

M & L for treating the bottom and sides of excavation at the rate of 5 ltrs of emulsion per sqm of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the back fill in contact with foundation at the rate of 7.50 ltr of emulsion per sqm of vertical surface complete all as specified and directed by Engineer-in-Charge

M & L for treating the top surface of filled earth at the rate of 5 ltr of emulsion per square meter of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the soil under plinth protection at the rate of 5 ltr of emulsion per square meter of surface area complete all as specified and directed by Engineer-in-Charge

M & L for treating the soil along with external perimeter of building at the rate of 2.25 ltr of emultion per meter of the perimeter wall complete all as specified and directed by Engineer-in-Charge

M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for foundations, including rafts, footings, foundations beams, plinth beams, bases for columns etc complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for columns, pillars, piers, post and strut complete all as specified and directed by Engineer-in-Charge.

M & L cement concrete M-25 desigh mix (using 20mm graded aggregate) for beams, cantilivers, beressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items.

M&L for brick work with old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

Same as item No. 62 above but except bricks.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

M & L for formwork to sides of concrete , foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work for rough finished surface complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantiliver shelves etc.for fair finished complete all as specified and directed by Engineer-in-Charge.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc.for fair finished surface complete all as specified and directed by Engineer-in-Charge.

M&L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns,footing, plinth beam, roof beam, lintels, slabs and other similar structures etc., hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge

- ditto- as ser item no 70 above but 5mm dia and over upto and inclluding 10mm dia in stirrups, spacers and binders etc complete all as specified and directed by Engineer-in-Charge

M & L excavated earth for spreading and levelling in layers n exc.25 cm thick and well ramming including watering as required complete all as specified and directed by Engineer-in-Charge

M & L for hardcore of broken bricks of gauge n exc. 63 mm , deposited , spread and levelled and compacted in layers n exc. 15 cm thick , watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10mm thick on other than fair face of brick work surfaces in CM 1:4, for fixing of tiles/kotacomplete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

M&L 75mm thick PCC type D2 (40mm graded aggregate) in floor sub base

M&L 75mm thick PCC type B1 (20mm graded aggregate) in floors finish

M& L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection. complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 300 X 300 X 7 to 8 mm thick (square/ rectangular) on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match i complete all as specified and and as directed

M&L for non-skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for non-skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in Skiting, riser etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for 18 to 20 mm thick machine cut pre polished (Granite Polished) kota stone tile as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing and polishing incl full round bull nosing complete all as specified and directed.

M & L for 16 to 18 mm thick machine cut pre polished (Granite Polished) kota stone tile as in riser of steps, skirting in full length in single peice without joint, with groove cutting in double line of stair width laid over 15mm thick cement screed in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade including necessary grinding, rubbing and polishing (mirror finish) and bullnosing complete all as specified and directed.

M & L 16 to 18 mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:6 to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and fair without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in two layers on fair faces of brick work or concrete surfaces first layers 10 mm thick with cement mortar 1:6 on fair faces of brick work or concrete surfaces and second layers 5 mm thick with cement mortar 1:4 finished even and smooth without using extra cement with mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. Note:- Water Proofing compound shall be measured and paid seprately.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of brick work or concrete to be finshed even and smooth without using extra cement over 10 mm thick in 1:3 after applying one coat of alkaline anticorrosion chemical coating having specific gravity of 1.2 to 1.22 upon exposed reinforcement with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Taking down existing un-serviceable water proofing treatment from roof slab and cleaning the roof slab by wire brush and removing WPT felt exc 500 mtr but not exc 1.50 Km etc complete all as specified and as directed

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

M&L for 3 mm thick APP modified prefabricated in five layers & weight not less than 3.6 Kg/Sq mtr water proof membrane reinforced with non-wooven polyster with two coat of water proofing aluminium paint over top surface of water proofing membrane with 100mm (Minimum) end lap and 75mm (minimum) side lap and joints finally pasted with thermo- fused with LPG flames laid over a coat bitumen @ 1.20 Kg /Sqm over a coat of bituminous primer 0.40 ltr per sqm over after cleaning existing plastered surfaces as per manufacturer instruction of APP modified membrane etc. APP modified membrane shall be laid on bitumen surface by torch application method after allowing 24 hours for bitumen to dry, complete all as specified and as directed.

S&F 1.25 mm thick pressed steel frame of size 165 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M & L PCC 1:3:6 Type C 0 using 12.5 mm graded stone aggregate for backing of door chawkhats complete all as specified and directed by Engr-in Charge

S&F 35mm thick factory made flush shutter solid core construction with block board core and ply wood face panels, commercial type covered with approved quality & shade 1.00 mm thick lamination plain & mettalic high gloss on both sides of shutter complete all as specified and as directed

S&F for 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- Glass/gauge shall be measured and paid for separately.

S&F factory made steel windows (Box type) with side hung shutters precoated (colourcoated/ powder coated) with double shutters (glazed and gauged shutter bothn ) with frame complete all as specified and directed and shown on drg TD 158 sheet 1/2 & sheet 2/2 . NOTE :- Measurements shall be taken and paid compositly for frame, glazed and gauged. Grill shall be measured and paid seperately under respective item. No extra claim shall be entertained on this ground

S & F powder coated aluminium frame for doors, windows, ventilators/partitions with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F 6 mm thick coloured ACP sheets fixed to aluminum fame work with necessary SS screws and neoprene gasket complete all as specified

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated moulded shutter for kitchen cupboard. The laminated shutter should be 10 mm deep mould on the pre laminated side with different design and other side plain white of density not less than 600 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed. Make Kumar Arch Tech pvt ltd / Rajshree / Fiber Techno Products / Eco Cell / TVL Engineering Pvt Ltd (Floresta)

Supply & fixing factory made WPC door frame 100% Solid (wood polymer composite) Size 100mm x 50 mm Single Rebated ,made from wpc material comparising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed. Make : M/S Kumar tech , M/s Raj shree & M/s syntex

Supply & fixing 30mm thick prelaminated WPC factory made moulded door shutter consisting of solid core single leaf flush door of 25mm thickness, lipped with 15mm (5mmx3) thick x 30mm width on one stiles and top rails & 10mm (5mm x 2) thick x 30mm width on the other stiles & bottom rails, The inner panel laminated with 2mm thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 raised panel design in different plain and / or prelam colour on one side after routing the moulded design on flush door & 2mm plain and / prelam PVC sheet on other side using rubber based adhesive on flush door & solvent cement adhesive on the lipping etc. colour / pattern of laminate to be approved by GE complete all as specified and as directed. Make : M/S Kumar tech , M/s Raj shree & M/s syntex

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. .5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F double legged floor door stopper 150 mm long aluminium alloy with rubber etc complete all as specified and as directed

S&F ball catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed

S&F continous (piano) hinges, mild steel, bright finish or eletro galvanised with of flap (when opne) 30 mm etc complete all as specified and as direced

S&F aluminium extruded section body Door closer hydrau lically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed

S&F stainless steel decorative curtain rod of 25 mm bore with including brakets 02 nos finalie 02 nos) etc complete all as specified and as directed

S & F glossy finished SS 125 mm hasp and staple including bolt to hinge plate and fixed with S S screws complete all as specified and directed.

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed. Make: Hettich cat No Onsys 4447i product code 928143200 /Kaff nickel plated SC hinge 100°code No KHSC-0/Godrej product code :6933, Baan code LKYAHCHR4

S & F brass drawer locks grade I 50 mm size 2 lever complete all as specified and directed by Engineer-in Charge

S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F in repairs vitreous chinaware wash hand basin with pedestal of size 55X40 cm complete including CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed. Model : WHB - Cat No 10072, Pedestal- Cat No. Ped 11029 Neptune of Hindware ,Parryware Cat No C0480 (SP) 181/CTH ,C 0375 pedestral, Cera Cat No 2090107Ped , Cat No S 2040112 WHB

S & F Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make :- Cera Cat No. F 1015401, ESSCO (Jaquar) Cat No. MQT- 517BKN, Hindware Cat No. F320019

S & F in repair fancy type 100mm size square brass CP shower rose with or without swivel joints including shower arm complete all as specified and as directed. Model No: F7020305 CH of Cera , Hindware Model No F160006 , Parryware (with shower arm) Model No WPT9808A1, Cat No. for shower arm "Cera F7040102, Hindware F200028

S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed Make :- Cera Cat No. F 1015151, ESSCO (Jaquar) Cat No. MQT- 512KN, Hindware Cat No. F440003

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed Make :- Cera Cat No. F 1015201, ESSCO (Jaquar) Cat No. APR- 101053, Hindware Cat No. F40005

S&F as 15mm bore Pillar taps fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed Make :- Cera Cat No. F 1019101, ESSCO (Jaquar) Cat No. APR- 101001M, Hindware Cat No. F320001

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed Make :- Hindware Cat No. 20076, Cera Model No. CALINA S3010102, Parryware UTSAV XL 580 code WPC0117CS1C

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed. Model :- Sleek fresh dual flush of Hindware Model No Pastel size 47.6x15.5x32 , Parryware Cat No 8177*, Cera Cat No B1810110 fittings snow white

S & F 15mm dia brass chromium plated health faucet with 1.00 mtr long flexible tube and wall hook screwed for iron pipe fancy type long body and hanging arrangement complete all as specified and directed. Model :- ALD 573 of Jaquar ,Hindware Model No F160002, Parryware Model No T9961A1

S&F in repair vitreous china wash down water closet pan (pedestal pattern) with 'P' or 'S' trap white with PVC seat cover including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed. Model :- Hindware Cat No. 20079 (Seat & cover), Parryware Model C 0297(seat) & E-8071 (seat cover), Cera Model NO S1059101(seat) & B-1510121( seat cover)

S&F Virteous China bowl urinal flat back size of 590X390X375 mm with grating and union for discharge pipe ISI marked fixed in repairs.insluding CP spreader complete all as specifie and directed Make Cat Cera S4020112 Parryware C0586 Hndware 60002

S&F 1000 litre ISI marked rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in repair for 75 mm bore out let floor trap Cast iron spun pipe (conforming to IS 3989) incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed

S&F 50 mm bore cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with leadt joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F for 75 mm bore cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F for 100 mm bore cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or vertically cast, complete all as specified and as directed

S&F 75mm bore Bends of (any radius), cast iron spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 100 mm bore Bends of (any radius), cast iron spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 75mm bore Tee of (any radius), cast iron spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 100 mm bore Tee of (any radius), cast iron spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 50 mm cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out any type of soil and removing surplus soil to a distance n exc 50 m and making good surface

M&L PCC 1:2:4 type B-2 using 20mm graded stone aggregates as in foundation, posts filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section MS tubes, flats square bars etc as in roof trusses (framed) , trussed purlins, crane gantries , rails and fastening and heavy brackets framing inclusing distance pieces, cleats etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

M & L 595 mm X 595mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI powerd coated tee and cross tee of size 24x32mm & 24x27mm having 0.27mm gauge at every 600mm c/c interval and wall angle of size 19x19mm having 0.35mm gauge fixed to the wall. The above grid is tobe suspended at every 1200mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595 mm and ant ine of the design (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed by Engineer-in-Charge. (Make Everest or equivalent)

S&F framed work as in doors or gates of angle or other section Fe 410 W Gde E 250 with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete including cutting out of existing sheet if required complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

Preparation of new or previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M&L three coats of white wash on ceiling on new plastered surfaces including preparation of surfaces complete all as specified and as directed

M&Ltwo coats of white wash on ceiling on Old plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for preparation of new wall surface and applying wall putty 1-1.5 mm thick in two layer (Asian /Berger/JK) to make the surface smooth as specified and directed by Engr-in-Charge. (Note : The work will be carried out upto tripple storey building, the rate of scafolding is included for this item also)

M&L for preparation of old wall surface and applying wall putty 1-1.5 mm thick in two layer (Asian /Berger/JK) to make the surface smooth as specified and directed by Engr-in-Charge. (Note : The work will be carried out upto tripple storey building, the rate of scafolding is included for this item also)

Material & Labour for applying Two or more coats of 100% Premium acrylic distamper paint Alkali & fungal resistance, dirt resistance interior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer over prepared surface of with birla wall care putty complete as specified and directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion weather proof paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over prepared surface of with birla wall care putty complete as specified and directed

S & F 5 mm thick toughned glass as in partition including all necessary fitting/fixtures complete all as specified and directed

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified.

Blank

Blank

M&L for vitrified full body exterior coloured tiles 12 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm , in floors/skirting /riser/dado/treads etc. set and jointed in neat cement slurry and pointed in white or coloured cement to . including 15 ,mm thick cement screed bed in CM 1:6 etc complete all as specified and as directed

Blank

Blank

Blank

Blank

M & L for cement concrete 1:3:6 type C-2, using 40mm graded crushed stone aggregate for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed by Engineer-In- Charge

M & L for reinforced concrete pipes,150mm dia class NP-2 laid and jointed complete with collars complete all as specified and directed by Engineer-In- Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid separatelly).

Blank

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed by Engineer-In- Charge.

Blank

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

Blank

Septic tank conventional type brick work designed to carry sewage and sullage water, excavation in any type of soil,PCC 1:2:4 below foundation, RCC M-20 ( Nominal mix) in Roof slab and baffle wall with Vent shaft , manhole openings with cover connection etc,complete for 50 users. Drg No-TD/217 Sh 1/7 to 7/7

Sokage well, exc in any type of soil, foundation in PCC 1:2:4, walls of honey combed Brick work in CM 1:4, RCC cover slab in M20 (nomial mix) filling with brick bats, complete of size 3.00M dia x 3.00M deep.Drg No-TD/309 Sh 1/ to 4/4

M/L PCC 1:3:6 type C0 ( using 12.5 mm thick graded stone aggragate) as in surface channel drain. Complete all as specified and directed

M&L for GI steel tubing medium grade of 40 mm dia for water supply pipe line fixing to walls/underground including cutting and connection from exiting pipe line complete all as specified and directed.

Desludging/desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt/mud/peat/sludge out side of defence land complete all as directed by Engr-in-charge. Note: for item no 1 to 20 the work has to be carried under foul condition, hence the rate to be deemed included. Nothing extra shall be paid to the contractor on this account.

M/s Sagar Associates

SUSHIL KUMAR

M/S Hind Constructions

MOHAN LAL GUPTA

M/S Manmohan Singh Anand

M/s Anil Kumar

The new hut furnitures

Ms dev associates