Providing LWSS to NCPC Habitation Roda Nallah Satahan in GP Lagdhar Tehsil Sadar Distt MAndi HP

Amount

Cutting in earth work and disposal of excavated earth work in all kinds of soil such as pick work,jumper work,blasting work,chiselling in hard/soft rocks where blasting is prohibited in all leads and lifts complete as per the entire satisfaction of the Engineer-in-charge.

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing oof all surplus excavated soil as directed in all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-Charge.

Providing and laying cement concrete 1:3:6(1cement:3 sand:6 graded stone agg. 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:1:5:3 (1cement 1.5 sand :3 crushed stone agg. 20mm nominal size) and curing complete excluding the cost of form work and reinforcement concrete work in :- Foundation and plinth.

Walls (any thickness but ot less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level in all leadfs & lifts.

Beams, cantilivers, girders and lintels sides and soffits of beams, haunchings cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth in all leads and lifts.

Suspended floors,Dome roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers etcin all leads and lifts of any shape in all leads & lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level in all leads and lifts.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frames 30x30x5 mm, so as to give a fair finish including centering ,shuttering, propping etc.with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for-in-situ reinforced concrete and plain concrete work in:- Foundations, footings, bases of columns and the like and mass concrete in all leads and lifts:- in Foundations, footings, bases of columns and the like and mass concrete in all leads and lifts

Beams, cantilivers, girders and lintels sides and soffits of beams, haunchings cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth in all leads and lifts.

Vertical surface such as walls(any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like in all leads & lifts.

Providing from work of ordinary timber plankings so as to give a rough finish including centring,shuttering ,strutting and propping and centring below supporting floor to ceiling not exceeding 4 meters and removal of the same for re-in-situ reinforced concrete and plain concrete work in:- Arches , domes, vaults upto all span in all heights and removal of the same for -in-situ reinforced concrete and plain concrete work. in: -Arches, domes , vaults up to all span in all leads and lifts.

Providing and fixing precast concrete manhole cover and frame conforming to IS-12592-1988 (Part-I) and IS12592-1991 Part-II 500 mmdia (Medium duty) in all leads and lifts.

Laying, jointing and testing in trenches galvanised mild steel tube lGMS tubes (light grade) tube fitting In (Earth work to be measured and paid for separately ). In Inlet pipe 40 mm

Outlet pipe 32 mm

Scour pipe 50 mm

Providing and fixing Brass Wheel Valves (Medium pattern) screwed female ends, screwed in -bonnel inside screw, non rising stem, ordinary split, Taper, edge, non rising stem, integral seats & hand wheel operated, diameter mentioned below in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.in Inlet valve 40 mm

Supply valve 32 mm

Scour valve 50 mm

Steel work welded in built up sections,trusses and framed work including cutting,hoisting fixing in position and applying a priming coat of red lead paint: In gratting,framed guard bar,ladders ,railing brackets and similar works in all leads and lifts.

Providing and fixing wire gauge using galvanised M.S.wire gauge of IS gauge designation 85 G with wire of dia 0.56mm for ventilator of tank complete in all leads and lifts.

Providing and fixing of MS Fabricated Protection Panel having size 750 mm x 750 mm made with MS Angle 40 x 40 x 4 mm for frame, MS Angle 30 x 30 x 3 mm for cover, MS Flat 25 x 5 mm for fixing of sliding door bolt and MS Sheet 3.15mm thick for protection of manhole covers of storage tanks including the cost of cutting and welding of MS angle, MS Flat & MS Sheet, embedding in RCC Slab by drilling holes in MS angle & in RCC slab, provision for providing and fixing sliding door bolt 300 x 16 mm, MS Handle 100 mm, Lock and applying a coat of red oxide paint and painting two coat with steel paint (Firoza Blue) complete job in all respect in all leads and lifts and to the entire satisfaction of the Engineer - in - Charge.

JAGDISH CHAND

Raj Kumar