CA No CWE/HILLS/RKT/08 of 2020-21

Amount

S & F point wiring for one light point / fan point / bell point / 5 ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size, PVC insulated, unsheathed 1100 volts grade single core multi - stranded copper conductor cable (FRLS) drawn into and including Casing & Caping medium grade (not less than 20 mm dia) with and including its all necessary fittings and accessories and sunk cost iron or pressed steel terminal boxes for mounting fittings like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1,50 sqmm size solid copper conductor cable as in earth wire and connected to common earth dolly complete all as specified and directed.

All as per item No. 1 above but wiring for one 5 pin 5 Ampere socket outlet point on the same board, controlled by one, one way switch complete all as specified and directed

All as per item No.1 above but wiring with using cable 2.50 sqmm size and earth wire of PVC insulated (Green colour) 1.50 sqmm size solid copper conductor cable for one 3 pin socket outlet, 15 Amperes on independent board complete all as specified and directed.

Supply and fixing of switch piano flush button single pole one-way 5 Ampere complete all as specified and directged

Supply and fixing of socket outlet 5 Ampere, 2 and 3 pins (Total 05 Pins), flush type 250 volts AC complete all as specified and directed.

Supply and fixing of switch socket combination 2 in 1, 3 pin, 5 and 15 Ampere flush type universal complete all as specfied and directed

S & F lamp holder, PVC / polycorbonate type insulated body with back plate suitable for batten / angle fitting complete all as specified and directed

M & L ceiling rose, 3 phase / PVC / polycarbonate, isolated boldy complete all as specified and directed.

S & F LED tube light fitting. ,1x22w,T5, Energy Saving chennel suitable for LED lamp with standared fitting etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

S & F sheet metal enclosures for DB,s when MCB to be used single pole and neutral 240 Volt double door 4 way with 200 amp rated bus bar

S & F Isolator SPN 40 amp, 240 volts complete all as specified.

Supplying and fixing 1100 volts grade cable PVC insulated heavy duty aluminium multi-stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4 mm suspension wire from pole to service bracket, one 10 sqmm twin core cable flat or circular complete all as specified and directed

S & F MCB SP 5 to 20 amp, complete all as specified and directed.

M&L for anti-climbing device spikes type fabricated out of MS bar (round, square and flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified and directed.

M&L for danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white with letter figures and conventional skull and bones in signal red colour and fixed with MS clamps bolts and nuts of approved size for HT 25x20cm size complete all as specified and directed.

M&L for 11000 volts triple pole mechanically operated mounted on 12 insulator and steel frame with operating mechanism worked from ground level for current rating upto 400 amps for GOD complete all as specified and directed.

M&L for cable jointing kit for 11 KV (Earthed) grade cable for outdoor End termination heat shrink type joint complete with jointing material and accessoreis suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm complete all as specified and directed.

M&L for cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing materials and acecessores suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm complete all as specified and directed.

Supplying, laying and testing of XLPE cable with stranded aluminium conductor 11000 volts grade of cross section area of size 95 sqmm 3 core laid in trenches or fixed to wall or drawn through pipe with suitable size glands crimping type lugs etc complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide, depth exceeding 1.5 mtr and getting out in hard/dense soil complete all as specified and directed.

Returning , filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for dry clean sand filling in trenches below and around under ground cable cushioning complete all as specified and directed. Note :- Thickness of sand cushioning shall be measured after punning.

Supplying and laying un-reinforced precast concrete cable cover class HV type-1, flat size 300mmx180mmx40mm complete all as specified and directed.

Supply and fix unreinforced PCC cable cover class LV type-I of size 0.25x0.15x0.040 mtr complete all as specified and directed.

M&L for XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade laid in trenches or passiubng through pipes/ducts complete all as specified and directed with the following cross sectional area :- (a) 150 Sqmm 3.5 core

M&L for XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade laid in trenches or passiubng through pipes/ducts complete all as specified and directed with the following cross sectional area :- (b) 10 Sqmm 2 core

Supply, installation, commissioning and testing of step down, out door type transformer complete with standered fitting HT 11 KV, 3-Phase, LT 433 volts, 3 phase, 4 wire 50 Hz with tapping on HT side all as per IS.1180 of capacity 100 KVA including fitting and accessories complete all as specified and directed detailed as under: - (a) FITTING - (i) Type- Oil immersed, naturally costed star delta with neutral on LT side. (ii) Rating 100 KVA. (iii) Vactor group - DYN-II. (iv) Off load tap changing + 2.5%, + 5%, + 7.55 to be varied manually operated. (v) Initial oil filling- in accordance with IS- 335 of 1963. (vi) Winding - copper wound. (b) ACCESSORIES (i) Rating plate. (ii) Terminal marking plabe. (iii) Earth terminal for body & neutral. (iv) Drain value & plug. (v) Conservator with drain plug & valve. (vi) Dehtydrating breather. (vii) Oil level indicator. (viii) Explosion vent. (ix) Oil filling hole & cap. (x) Plain Roller. (xi) Air release device. (xii) Pial type thormometer. (xiii) Lifiting lugs.

Suppy, fixing, transporting, erecting and fixing steel tubular swaged pole type 410 SP- 31 (09 metres long) complete with cast iron base plate, finial taper plug MS bolts and washers incuding two coats of aluminium paint over a coat of red oxide primer to external surfaces of steel tubular pole and two coats of anti corrosive bituminous paint internally and externally upto planting depth of pole and providing 3 bands/ straps with paint red post office colour and 2 bands with black synthetic enamel paint 300mm from plinth block and marking pole No. with black synthetic enamel paint and feeder location of Pole including earth work/excavation in any type of soil PCC 1:4:8 type D-2 in foundation below pole, PCC 1:3:6 type C-2 around pole and plinth block of pole, disposal of surplus soil to a distance n.exc 50m and depositing where directed including dismantling of existing damaged steel pole/struts etc complete all as specified and directed.

Suppy, fixing, transporting, erecting and fixing steel tubular swaged pole type 410 SP- 55 (11 metres long) complete with cast iron base plate, finial taper plug MS bolts, and washers incuding two coats of aluminium paint over a coat of red oxide primer to external surfaces of steel tubular pole and two coats of anti corrosive bituminous paint internally and externally upto planting depth of pole and providing 3 bands/ straps with paint red post office colour and 2 bands with black synthetic enamel paint 300mm from plinth block and marking pole No. with black synthetic enamel paint and feeder location of Pole including earth work/excavation in any type of soil PCC 1:4:8 type D-2 in foundation below pole, PCC 1:3:6 type C-2 around pole and plinth block of pole, disposal of surplus soil to a distance n.exc 50m and depositing where directed including dismantling of existing damaged steel pole/struts etc complete all as specified and directed.

M&L for mild steel work Fe-410-S grade in cross arms, bracing, supports,clamps and back plate, fabricated from structural steel section including nuts bolts and washers, welding, bending cold or hot drilling holes for bolts in any shape or size as indicated or directed and including two coats of aluminium paint over a coat of red oxide primer including dismantling cross arms of mild steel channel or angle section etc complete all as specified and directed.

Supply and fixing LED street light fittings 45 watt including suitable type type of bracket incl 25 mm dia pipe clamp, nut and washer etc testing after to the satisfaction of GE complete all as specified and directed. Note: Old street light fitting should be diposited in MES store under repair.

Supply and fixing of street light cable junction boxes on pole including 10 Amp, SP, MCB and busbar etc. of box size 300 x 200 x 105 mm with terminal complete all as specified and directed.

Supply and laying in trenches GI tubing light grade pipe for crossing of road and protection street light cable near pole complete all as specified and directed for the following sizes :- (a) 80 mm dia bore

Supply and laying in trenches GI tubing light grade pipe for crossing of road and protection street light cable near pole complete all as specified and directed for the following sizes :- (b) 25 mm dia bore

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in hard/dense including removing of all shurbs, splings, bushes, tress not n.exc 30 cm girth as in hard/dense soil complete all as specified and directed.

Earthwork in excavation in foundation trenches n.exc 1.50m wide and n.exc 1.50m in depth and getting out in hard/dense soil complete all as specified and directed.

M & L for cement concrete in foundation filling and mass concrete type C-2, 1:3:6 (40 mm graded stone aggrigate) complete all as specified and directed.

M & L for block masonry with solid pre-cast cement concrete blocks made out of cement concrete 1:3:6, type C-1, using 20 mm graded crushed stone aggregate, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work/concrete surface in CM 1:4 finished even and fair complete all as specified and directed.

M&L for two coats of cement based paint on newly plastered/unplastered surfaces including preparation of surface complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8), type D-2 as in sub base and finished even and rough complete all as specified and directed.

M & L for RCC 1:2:4, Type B-1 (using 20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams, plinth beams, plinth band, lintel bands, bases for columns, etc. basement slabs, floors, under reamed piles and mass concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Ditto all as per item No. 42 above herein before but 6 mm to 8 mm dia as in stirrups complete all as specified and directed.

Formwork to fair finished surface to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc. 10 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

M & L for PCC 1:3:6 type C-1, (20 mm graded stone aggregate) in coping, kerbs and the like including weathering slidly rounded or chemfered angle and throating complete all as specified and directed.

S & F framed work such as grill, grating, post and struts in fencing including coutting tops, notching to shape for securing wire mess etc with ends of bar shoulders and / or rebeated or forged, framed guard bar, bared iron door, ladders, framed balusters, walk ways, railing, frmaed work water tank and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of steel or iron surfaces, exc 10 cm width or girth, complete all as specified and directed.

M & L for preparation of new painted steel and iron surfaces of any description not exc. 10 cm width or girth when unconnected with painted surface or painted with different tint and applying one coat of synthetic enamel paint complete all as specified and directed

Fixing only chain link fencing including line wire, any mesh type of standard rails straining bolts etc., including provision of binding wire complete all as specified and directed. Note: Chain link mesh shall be supplied and measured under relevant item of schedule

Supply only chain link mild steel galvanised fencing n exc 4 Kg/ sqm of any size and type complete all as specified and directed.

M & L for Shingle filling in floors or pavings, laid in layers n exc. 15m thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.

M&L for Earthing complete with galvanized sheet earth plate electrodes 600x600x6 mm thick buried directly in ground (earth pit not less than 2. 25mtr deep below ground level) with top edge of plat not less than 1.5 mtr below normal ground level connected to galvanized iron strip 32 x 6 mm as earthing lead by means of bolts, nuts , check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I including excavation and earth work, GI pipe light grade 40 mm bore for protection of GI strip from earth electrode to and incl the earth test point of galvanized Iron/steel of size 75x75x 25mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh,20 mm dia GI pipe light grade for watering and connected to earth test point including brazing at all joints except at test point and testing complete all as specified and directed.

M&L for earthing complete with galvanised steel earth,plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground (earth plate not less than 2.25 mtr below normal ground level connected to GI earth lead wire 4mm dia by means with top edge of the plate not less than 1.5 mtr below normal means of bolts , nuts, check nuts and washers of galvanied iron or steel and including 15mm dia GI pipe light grade for protection of earth wire upto a length including earth work/excavation PCC 1:2:4 type B-1 as in earth pit. RCC pit cover 50mm thick precast RCC 1:2:4 type B-1 duly reinforced with 8 mm dia mild steel TMT bars @ 150mm c/c both ways with 10mm dia MS bar for fitting handle including 20mm dia GI pipe medium grade 1.5 mtr long as watering pipe, funnel, wire mesh etc complete all as specified and shown in electric plate No 3 of SSR Part-I including testing on completion etc complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide, depth exceeding 1.5 mtr and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 as in plinth protection/path, 75 mm thick finished even and smooth complete all as specified and directed.

M&L for hard core of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, 100 mm thick as in flooring finished even and smooth using extra cement complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set jointed and pointe in neat cement slurry with grey cement and pigment over and including 20mm thick screed bed in CM 1:6. complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick wall/cement concrete surfaces in CM 1:6 complete all as specified and directed

M&L for 15mm thick plastering in CM 1:4 finished even and smooth without using extra cement on other than fair face of Brick/stone/concrete surfaces complete all as specified and directed.

M & L for Providing, cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate in roof kerbs of mud stops, rounded or chamfered on edges, in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed.

S & F Roof trusses (framed), trussed purlins, purlins, false rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat, MS plates sections) including distance pieces, cleats etc. Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F prepainted aluminium zinc steel sheet (galvalume base) or thinknee 0.50mm having tensile strength of 550 MPA , in colour and profile as apporved by GE and to be facotry moulded as in roof covering /cladding and fixed with hot dipped galvanished with high durable protective triple coated self tapping screws /self drilling serews, to suit the roofing in customized colour matching with the colour of roofing and screws are to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified and directed (Make -colour roof inda ltd or TATA Bluescope)

S & F Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut,Diameter of neck in mm Exc 12mm n exc 20mm complete all as specified and directed.

M&L for second class hard wood plain, solid, straight chowkats frames, wrought framed, rebated on the solid, rounded or chamfered put together with glue primed at joints complete all as specified and directed.

M/L for 35 mm thick panelled shutter using IInd class hard wood (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. Complete all as specified and directed.

S&F 35 mm thick second class hard wood glazed and skelton open rebated and prepare to receive glass/gauge etc. (without sash bars), edges of framing plain chamfered or rounded, fitted without mitred beads for securing glass etc size of members of shutters as specified in SSR Part 1 Sec 8 clause 8.23 (a) complete all as specified and directed.

M&L for bands, straps, supports or stays for rain water ventillating pipe as in small articles like hold fasts confirming to Fe-290 Gde-E-165 complete all as specifed and directed.

S&F butt hinges heavey weight, cold rolled mild steel, of size of hinges 100 mm complete all as specified and directed.

S&F 200 mm Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F extruded aluminium alloy, anodised fabricated type handle of size 150mm complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F butt hinges heavey weight, cold rolled mild steel, of size of hinges 75 mm complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section size 100mm long complete all as specifed and directed.

S&F extruded aluminium alloy handle 100mm size anodised fabricated type complete all as specified and directed.

S&F glass sheet 4 mm thick of ordinary quality & glazing with oil putty in squares n.exc. 0.50 Sqm in each pane complete all as specified and directed.

M&L for painting wood or wood based new surface of any description over 10cm width or girth with applying two coats of synthetic enamel paint over a coat of Pink primer including preparation of surfaces complete all as specified and directed.

M&L for three coat of white washing newly plastered wall surfaces including preparation of surface complete all as specified and directed.

S & F GI frame work powder coated for seamless/made in panels (605 mm x 605 mm) ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre complete all as specified and directed.

M & L for 4 mm thick non asbestos fibre cement building board (E-board classic) fixed or laid/inserted to timber/GI/Aluminium framework with screws complete all as specified and directed.

Excavating in over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in Cement mortar 1:6 complete all as specified and directed.

M & L for Hand packing with broken stone boulders (40 mm thickness) at the back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed.

M & L for Providing, precast cement concrete in window or door cills, lintels, bressummers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. and setting in mortar complete with joints to match PCC Bounders complete all as specified and directed.

M&L for raised pointing to radom rubber uncoursed stone walling with CM 1:4 complete all as specified and directed.

M & L for PVC pipe (SWR) 110 mm bore pipe mm bore single scoketed in any length with rubber ring joints laid in treches or in floors complete all as specified and directed.

M/S HILTRON SYTEM

kumar automobiles

URBANS CONSTRUCTIONS