Development Of Taluk Hospital Feroke in Kozhikode District

Amount

SUBSTRUCTURE

2.33.2 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyound 60 cm girth up to and including 120 cm girth

2.33.3 : Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Beyond 120 cm girth up to and including 240 cm girth

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.7.3 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

SUPERSTRUCTURE

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

CIVIL FINISHING WORKS

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.44.1 : Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

26.43 : Providing and fixing internal wall panels on Light gauge steel frame work with12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mmthick fiber cement board conforming to IS 14862:2000 of category III type B(High pressure steam cured) as per standard sizes fixed with self-drilling / tapingscrews / fasteners @ 60cm c/c of approved make, Screws shall be of countersunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of framework to be paid for separately)

26.41 : Designing, providing, installing and fixing factory finished custom designedcold form Light Gauge Steel Framed super structure comprising of steel wallpanel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steelsheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steelframing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFSframe shall be designed as per IS: 801 using commercially available softwaresuch as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revitarchitecture-2011 or equivalent. Proper usage of Connection Accessories likeHeavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect trusswith wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-ShapedAngles for better structural stability. The framing section shall be cold formC-type having minimum web depth 89 mm x 39mm flange x 11mm lip in requiredlength as per structural design requirement duly punched with dimple/slot atrequired locations as per approved drawings. The slots will be along centreline of webs and shall be spaced minimum 250mm away from both ends of themember. The frame can be supplied in panelized or knock down condition inspecific dimensions and fastened with screws extending through the steelbeyond by minimum of three exposed threads. All self drilling tapping screwsfor joining the members shall have a Type II coating in accordance with ASTMB633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 oflength 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprenerubber using self expanding carbon steel anchor bolt of dia as per approveddrawings. design subject to minimum 12mm diameter and 121mm lengthconforming to AISI 304 and 316 at 500mm c/c with minimum embedment of100mm in RCC (RCC to be paid separately) and located not more than 300mmfrom corners or termination of bottom tracks complete in all respects. Theitem also includes the submission of stability reports duly examined and issuedby any NIT/IIT. The rate includes the concept design, detailed design,fabrication of sections, transportation, installation and all required fixingarrangement at site as described above.

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.12.2.5 : Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x 800 mm

11.47.3 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 800x800 mm

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

od295548/2020_2021 : Providing and laying anti skid Ceramic floor tiles of size 400x400 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

8.13.1 : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye orequivalent.

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

50.9.11.1 : Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sectionsas per the architectural drawings and approved shop drawings , the aluminiumquality as per grade 6063 T5 or T6 as per BS 1474,including super durable powdercoating of 60-80 microns conforming to AAMA 2604 of required colour and shadeas approved by the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminiumframe work. Nothing extra shall be paid on this account).

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

9.12 : Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. ( Area of opening for glass panes excluding portion inside rebate shall be measured).

9.117.1 : Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.118.1 : Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter).

9.165.1 : Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.100.1 : Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

9.71.1 : Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.97.3 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

9.103 : Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc . complete.

21.4.1 : Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge.With stainless steel cover plate minimum 1.25 mm thickness

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

od295550/2020_2021 : Radiation Saftey Lead Lined Door For Hospital, Rust proof and Zinc Polished

6.13.2 : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement : 4 coarse sand)

od295552/2020_2021 : Wall corner guard (Corner protector):<br>Providing and fixing of 5 feet height Vinyl cover with wear and resistance and anti-bacterial ability, aluminium retainer for strong impact resistance ability, high flame retardant performance wall corner guards.

od295553/2020_2021 : Proving Hand grabs inside Handicaped Toilet as per the direction of Engineer in charge

ELECTRICAL-LT

od295766/2020_2021 : 2.4.3<br>Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)<br>8 way (4 + 24), Double door

od295770/2020_2021 : Supplying and fixing following way, horizontal type three pole and neutral, sheet<br>steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper<br>bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including<br>earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

od295783/2020_2021 : Supplying and fixing following way, Flexible type , sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper busbar, neutral bar(4 Nos), earth bar(4 Nos), din bar, interconnections, powder painted including earthing etc, as required (But without MCB/ RCBO/ RCCB/ Isolator)-4 Row 14 Module

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.13.3 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

2.14.1 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od295801/2020_2021 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, RCBO, in the existing MCB DB complete with connections, testing and commissioning etc. as required.-32 amps

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.2 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

od295804/2020_2021 : 2/3 Plate Ceiling Rose

od295805/2020_2021 : Supply, Installation ,Testing and commissioning of Floor Box 250x250x60mm (17Module)

1.34 : Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

od296461/2020_2021 : 1200mm sweep ceiling fan, complete with 300mm down rod, canopies, shackles<br>and blades working on 230/240V single phase A/C and giving connection with<br>required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper<br>conductor flexible wire conforming to ISS, etc. as required.

od295810/2020_2021 : 225mm sweep heavy duty exhaust fan in metal frame working on 230V A/C.The work shall include making the holes suitable for the size of fan, fixing necessary bolt and nuts making good the damages, etc. and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as require

4.1.4 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.6 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X50 mm depth X 2.0 mm thickness

4.1.7 : Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

1.8.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.9 : Wiring for twin control light point with 1.5 sq.mm FRLC PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLC PVC insulated copper conductor single core cable etc as required.

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

od295820/2020_2021 : Supply & installatopm of adaptable DLP U-PVC trunmking installed on wall/ fixed furniture/ skirting complete with cover and seperation partition<br>150 X 50 mm

od295821/2020_2021 : Supply and installation of disconnect switches (isolators) in metallic enclosures to provide power supply to mechanical equipment.

od295823/2020_2021 : 63A TPN Isolator

od295824/2020_2021 : 35Litter water heater<br>

od295825/2020_2021 : Supply, installation, testing & commissioning of Water lifting pump, with pumps (2 nos on a 1duty + 1 standby basis) with control panel,automatic changover switch, with all necessary valves, flexible connections, pressure gauges, strainers, supports, fixings and fittings electrical/ control panels, power and control cabling , cable trays, automatic level controller, etc. as specified and as shown on drawings and complying to relevant standards. <br>COLD WATER LIFTING PUMP (Well to UG Tank)<br>Duty conditions:-2.5 LPS @ 50 M Head (One Duty + One standby) (WTP-01/02)<br>

od295826/2020_2021 : Supply, installation, testing & commissioning of Water lifting pump, with pumps (2 nos on a 1duty + 1 standby basis) with control panel,automatic changover switch, with all necessary valves, flexible connections, pressure gauges, strainers, supports, fixings and fittings electrical/ control panels, power and control cabling , cable trays, automatic level controller, etc. as specified and as shown on drawings and complying to relevant standards. <br>COLD WATER LIFTING PUMP (UG Tank to OH Tank)<br>Duty conditions:-3.0LPS @40 M Head (One Duty + One standby) (WTP-03/04)<br>

od295827/2020_2021 : Supply, installation, testing & commissioning of Water lifting pump, with pumps (2 nos on a 1duty + 1 standby basis) with control panel,automatic changover switch, with all necessary valves, flexible connections, pressure gauges, strainers, supports, fixings and fittings electrical/ control panels, power and control cabling , cable trays, automatic level controller, etc. as specified and as shown on drawings and complying to relevant standards. <br>FLUSH WATER LIFTING PUMP (UG Tank to OH Tank-STP)<br>Duty conditions:-2.0 LPS @40 M Head (One Duty + One standby) (WTP-07/08)<br>

od295828/2020_2021 : BOOSTER PUMP SETS<br>Supply, storage, installation, testing & commissioning of VFD operated Vertical multi stage Water boosting pump system ,with pumps (2 nos on a 1duty + 1 standby basis) with control panel,pressure vessel, automatic changover switch, VFD control panel with all necessary valves, strainer, flexible connections, pressure gauges, supports, fixings and fittings electrical/ control panels, power and control cabling , cable trays etc as specified and as shown on drawings and complying to relevant standards. <br>COLD WATER BOOSTING PUMP <br>Duty conditions:-3.50 LPS @ 20M Head (One Duty +One standby) (BWSP-01~02) With pressure vessel<br>

od295829/2020_2021 : WATER LEVEL CONTROLLER ,Providing and fixing automatic level controller with panel, control cabling,cabling, Automatic OHT Level Control system Consists of Water Level Float Switch with control Cable for water supply ,including all accessories, WATER LEVEL CONTROLLER<br>which required to complete the system for working conditions as per specifications.<br>

od295830/2020_2021 : Supply , installation, testing & commissioning of constant speed Pumping system ,with waste water lifting pumps(1 working + 1 stand by), control panel with all necessary valves,controls, water level controller , flexible connections, pressure gauges, strainers, supports, fixings and fittings electrical/ control panels, power and control cabling , cable trays etc as specified and as shown on drawings and complying to relevant standards. <br>DWTP 01/02 (Fire Pump Room Sump to soak pit) (Submersible)<br>Duty conditions:- 180LPM @ 1.0 Bar<br>Supply & Installation<br>

od295831/2020_2021 : Energy efficient recessed mounted LED light fittings suitable for 600x600mm grid-type suspended ceilings

od295832/2020_2021 : Energy efficient recessed mounted square LED light fittings of size 220x220mm

od295833/2020_2021 : Low glare, hight effeciency recessed mounted LED down light - circular profile - IP20

od295834/2020_2021 : Low glare, hight effeciency recessed mounted LED down light - circular profile - IP44

od295835/2020_2021 : 1.2m long ceiling surface / wall mounted LED Batten light fitting

od295836/2020_2021 : 0.6m long ceiling surface / wall mounted LED Batten light fitting

od295837/2020_2021 : Impact resistant and weatherproof bulkhead-type light fitting

od295838/2020_2021 : Impact resistant and weatherproof LED Bollard light - IP65

od295839/2020_2021 : Incinerator- Electrical works

od295840/2020_2021 : Medical gas plant room- Electrical works

ELECTRICAL-HT

od295767/2020_2021 : Supply, installation, testing and commissioning of 11kV, 630A, 20kA, Motor operated, Compact, Outdoor, both side Extensible, Non-drawout type, CCV+ (2nos. Load Break Switch (OD) incomer and 1no. fixed type motor operated Vacuum Circuit Breaker (VL) outgoing) compact gas insulated Ring Main Unit, All live parts enclosed in a robotically welded stainless steel tank of IP 67 class of protection with Battery and Battery Charger.

od295771/2020_2021 : Unitised Sub Station - Indoor -l - 11kV - 315kVA<br>"11KV/433V, 3 phase, AN cooled, Vector DYN-11 cast Resin Transformer with On load tappings from +5% to -15% in steps of 1.25%, operated by 11KV RTCC and AVR with LT busduct and HV terminals connected to 11KV, 26KA,630A Load Break Switch WITH earth switch, shunt trip coil and emergency OFF push button with incoming suitable for XLPE cable and output connected to 11KV seal off bushing to the transformer.<br>Type: TF"<br>

od296581/2020_2021 : 3ph, 3wire, 110V(L-L), -/1A CT or -/5A<br>CT TOD Meter with CTs & PTs<br>

od295784/2020_2021 : SUPPLY OF HT CABLES-Supply, testing and commissioning of the following PVC Insulated Armoured Aluminium Cables (AYWY/AYFY) /XLPE (A2XCEFY) to be laid in HT trenches, cable trays, hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers etc. required for clamping intervals as necessary.

8.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

10.4.4 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

od295791/2020_2021 : 250kVA DG set <br>Supply, installation, testing and commissioning of 250kVA, 415V, 3 phase, 1500rpm, 0.8pf water cooled, floor mounted Diesel Generator set with acoustic enclosure and control panel, necessary controls, contactors, timers, meters, energy meter, indication lamps, etc. as required for synchronisation of two DG sets, Suitable MCCB with shunt trip and adjustable over load 0.4In to 1In and adjustable short circuit 2 to 10Ir and ON- OFF push buttons. Relays, CTs and transducers for metering and protection. Fuel pipe line, exhaust pipe line (to be erected with sufficient MS supports and insulated, hood on top), Antivibration mountings, residential type silencer, electric starter, battery & battery charger, fuel tank, radiator, control wiring etc.

od295792/2020_2021 : UNINTERRUPTIBLE POWER SUPPLY <br>Three phase (input and output) 440V, 50Hz UPS with 15min backup with SMF battery. The system shall be true online, double conversion technology IGBT-based invertor and rectifier with pf >9.5, THD <3%, in-built isolation transformer, provision for parallel redundancy and 100% generator compatabile. The system shall comply to IEC /EN 62040-1 and relevant IS standard.

od295793/2020_2021 : MAIN DISTRIBUTUION BOARD<br>The panel shall be complete with all necessary switch gear, control gear, control wiring, metering, relays, etc. required (even if not speicfically listed below) for auto and manual load management of incomer, bus coupler and outgoing circuit breakers by PLC / SCADA.<br>

od295794/2020_2021 : SUB MAIN DISTRIBUTION BOARD (MSB-UT)<br>

od295795/2020_2021 : SUB MAIN DISTRIBUTION BOARD (UT-PMP)<br>

od295796/2020_2021 : SUB MAIN DISTRIBUTION BOARD (UT-LFT)<br>

od295797/2020_2021 : SUB MAIN DISTRIBUTION BOARD (UT-UPS-ISB)<br>

od295798/2020_2021 : SUB MAIN DISTRIBUTION BOARD (UT-UPS-OSB)<br>

od295799/2020_2021 : SUB MAIN DISTRIBUTION BOARD (MSB-LT&POWER )<br>

od295800/2020_2021 : SUB MAIN DISTRIBUTION BOARD (MSB- AC )<br>

od296474/2020_2021 : 100KVAR APFC PANEL Automatic Power Factor Correction Panel made of 16SWG thick CRCA sheet fully compartmentalised, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board,heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with 520V, APPH, Heavy Duty Capacitor, Capacitor Duty contactor and microprocessor based APFC Relay in steps of 8/12/14 with all required accessories.<br>

od296582/2020_2021 : Supply, laying, testing and commissioning of the following Aluminium LT Cables (AYWY/AYFY) / (XLPE) in trenches,on cable trays or through hume pipes, including supply and fixing of painted MS clamps, spacing of the clamps not exceeding 60cms, nuts and bolts, screws, identification tags, route markers, etc.required for clamping intervals as necessary.<br>1 x 3.5C x 300 Sq.mm.

od295806/2020_2021 : 1 x 3.5C x 185 Sq.mm.

od295807/2020_2021 : 1 x 3.5C x 150 Sq.mm.

od295809/2020_2021 : 1 x 3.5C x 95 Sq.mm.

od295811/2020_2021 : 1 X 3.5C X 70 Sq mm

od295812/2020_2021 : 1 x 3.5C x 50 Sq.mm.

od295813/2020_2021 : 1 x 3.5C x 25 Sq.mm.

od295814/2020_2021 : 1 x 4C x 16 Sq.mm.

od295815/2020_2021 : 1 x 4C x 10 Sq.mm.

od295816/2020_2021 : 1 x 4C x 6 Sq.mm.

od295817/2020_2021 : 1 x 4C x 4 Sq.mm.

od295818/2020_2021 : Armoured Copper Cable-1 x 4C x 4 Sq.mm.

od295819/2020_2021 : Armoured Copper Cable-1 x 4C x 2.5 Sq.mm.

od295822/2020_2021 : Armoured Copper Control Cable-12C x 1.5 Sq.mm

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

9.1.30 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.24 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.22 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

od295844/2020_2021 : E A R T H I N G-Supply and installation charges for Providing 1200x 1200x12 mm Cast Iron plate earth station, conforming to IS 3043 filling with mixtures of salt, sand and charcoal, construction of earth chamber with brick masonry and covering with heavy duty Cast Iron Cover hinged to Cast Iron Frame, including excavation & backfilling of earth pit.

od295845/2020_2021 : Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc as required.

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earthelectrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

od295846/2020_2021 : Providing and fixing 10 SWG dia G.I. wire on surface or in recess<br>for loop earthing as required.

5.20 : Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

6.7 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightningconductor complete as required.(For horizontal run)

6.8 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightningconductor complete as required.(For vertical run)

6.14 : Providing and laying G.l. tape 32 mm X 6 mm from earth. electrode directly in ground as required.

6.12 : Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providingmasonry enclosure with cover plate having locking arrangement and watering pipe etc. withcharcoal/ coke and salt as required

HT-MISCELLANEOUS ITEMS

od295763/2020_2021 : Supply and installation of rubber mat with ISI mark suitable for 11 KV,2.5mm THICK installation conforming to IS:15652:2006

od295768/2020_2021 : Supply and installation of 2nos fire buckets along with stand painted with enamel paint of red colour.

od295769/2020_2021 : Supply and installation of emergency OFF trip push button with front Glass and painted in RED Colour.

od296583/2020_2021 : Supply, fabrication and erection of exhaust pipe for carrying exhaust smoke from 200 KVA & 82.5 KVA DG set through existing masonary duct using MS pipe with 110mm increase in diameter for every 10m with asbestos fibre insulation, AL cladding, necessary suports etc complete

od295776/2020_2021 : Supply and Installation of Cable route marker for HT UG Cable at every 10m interval made of Cast Iron ( 152mm Round )

od295778/2020_2021 : Supply and fixing CO2 type 4.5KG capacity trolley mounted fire extinguishers as appoved by ISI complete as required

od295780/2020_2021 : Supply and installation of Danger board as required by the electrical authorities.

od295782/2020_2021 : 'Supply and installation of Laminated copies of Approved/ as built schemes and drawings in electrical room

od295786/2020_2021 : Supply of Insulated hand gloves IS 4770/1991

od295788/2020_2021 : Supply, Installation, Testing and Commissioning of Aviation Lamp (LED type )

PLUMBING WORK

17.3.1 : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.1 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

od206907/2020_2021 : "Supplying and fixing white glazed earthenware Urinal of 375X390X590 mm or nearest size (Indian make best quality) fixing with TW plugs and screws embedded in CM, providing 40mm CP waste – 1no, 15mm Angle cock pressmatic with wall flange - 1 no, Urinal spreader including cutting, making good the walls and floors etc. complete.

17.11.2 : Providing and fixing white vitreous china laboratory sink with C.I brackets, C.P. brass chain with rubber plug 40 mm C.P brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required:Size 600x450x200 mm

od299801/2020_2021 : Shower System unit comprising of single lever shower diverter/mixer with upper trim, bath spout, casted type multi-flow shower head with wall/ceiliing flange and necessary fittings and complete including breaking and making good the wall and floor as per Architectural drawings and relevant standards.

50.17.1.4 : Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

od299802/2020_2021 : Supply, installation and commisiioining charges for Long Body Type Bip Tap including, accessories, wall flange, washers,etc. as applicable, complete including breaking and making good the wall as per Architectural drawings and as relevant standards.

17.34.1 : Providing and fixing toilet paper holder:C.P. brass

50.17.1.1 : Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.3 : Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

17.72 : Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

od244592/2019_2020 : Supply, installation and commisioining charges for Toumbler Holder including, accessories, bolts/screws, washers,etc. as applicable, complete including making good the wall as per Architectural drawings and as relevant standards.

od243464/2019_2020 : Supply, installation and commisiioining charges for Robe Hook including, accessories, bolts/screws, washers,etc. as applicable, complete including making good the wall as per Architectural drawings and as relevant standards.

od243465/2019_2020 : Supply, installation and commisiioining charges for 850mm stainless stell Grab Bar including, accessories, bolts/screws, washers,etc. as applicable, complete including making good the wall as per Architectural drawings and as relevant standards.

17.71 : Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

od243474/2019_2020 : Supply, installation and commissioning charges for Floor Drain Outlets including, accessories, bolts/screws, washers, etc. as applicable, complete including making good the wall as per Architectural drawings and as relevant standards.<br>125X125 (Frame size) 1.2mm thick SS 304 grade lockable type floor drain

18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall20 mm nominal outer dia pipes

18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall25 mm nominal outer dia pipes

18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall32 mm nominal outer dia pipes

18.7.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall40 mm nominal outer dia pipes

18.7.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal outer dia pipes

od243525/2019_2020 : Supply, installation, testing & commissioning of water supply system pipe work including solvent welded/threaded fittings(tees, elbows, unions, reducers, coupling, etc.), GI "U" bolts, GI slotted rails, rail legs, accessories, etc. for supply riser, distribution risers, ring mains, suspended pipes, etc. with pipes and fittings as per uPVC schedule-40/80 suitable for working pressure of 20bars all in accordance with drawings and relevant standards.Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.Above Ground/Open Piping (Nominal Dia) 65 mm dia

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.9.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work20 mm nominal outer dia pipes

18.9.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work25 mm nominal outer dia pipes

18.9.5 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work40 mm nominal outer dia pipes

18.9.6 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work50 mm nominal outer dia pipes

od244765/2019_2020 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards, 20 mm dia .

od244769/2019_2020 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards, 25 mm dia

od244772/2019_2020 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards, 32 mm dia

od244776/2019_2020 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards, 40 mm dia

od244780/2019_2020 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards, 50 mm dia <br>

od150523/2020_2021 : Supply, installation, testing and commissioning of fullway lever operated forged brass ball valves with brass body with necessary MTA fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards<br>65 mm dia Ball Valve

od244812/2019_2020 : Supply, installation, testing and commissioning of spring loaded brass check valve(PN-16) with forged brass body, forged brass disc, with screwed end fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards 50 mm dia <br>

od244813/2019_2020 : Supply, installation, testing and commissioning of spring loaded brass check valve(PN-16) with forged brass body, forged brass disc, with screwed end fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards 40 mm dia

od245016/2019_2020 : Supply, installation, testing and commissioning of spring loaded, vertical mounted brass air release valve with forged brass body, forged brass chamber, with screwed end fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards 20mm dia

od245024/2019_2020 : Supply, installation, testing and commissioning of high pressure float valve with bronze construction, copper floats, with screwed end fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards 50mm

od245026/2019_2020 : Supply, installation, testing and commissioning of high pressure float valve with bronze construction, copper floats, with screwed end fittings with all supports and fixings all as specified and as shown on drawings and complying to relevant standards 40mm

od245122/2019_2020 : Supply, installation, testing and commissioning of brass Y-type strainer with screwed drainplug, SS 304 screen with supports, flanges, fixings and fittings all as specified and as shown on drawings and complying to relevant standards<br>50 mm dia

od245123/2019_2020 : Supply, installation, testing and commissioning of brass Y-type strainer with screwed drainplug, SS 304 screen with supports, flanges, fixings and fittings all as specified and as shown on drawings and complying to relevant standards<br>40 mm dia

od245186/2019_2020 : Supply, installation, testing & commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds. 25 mm dia

od245187/2019_2020 : Supply, installation, testing & commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds. 40 mm dia

od245124/2019_2020 : Supply, installation, testing & commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds. complying to relevant standards , 50mm dia

od245193/2019_2020 : Supply, installation, testing & commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds. 65 mm dia

od245178/2019_2020 : Supply, installation, testing & commissioning of uPVC puddle flanges in the water tanks with necessary fittings in accordance with the drawingsand relevant standerds. 80 mm dia

18.1.1 : Providing and fixing Polyethelene - Aluminium - Polyethelene ( PE - AL- PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80?C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes testing of joints complete of joints complete as per direction of the Engineer -in-Charge. Internal work - Exposed on wall1216 ( 16 mm OD) pipe

18.1.2 : Providing and fixing Polyethelene - Aluminium - Polyethelene ( PE - AL- PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80?C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes testing of joints complete of joints complete as per direction of the Engineer -in-Charge. Internal work - Exposed on wall1620 (20 mm OD) pipe

18.1.3 : Providing and fixing Polyethelene - Aluminium - Polyethelene ( PE - AL- PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80?C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes testing of joints complete of joints complete as per direction of the Engineer -in-Charge. Internal work - Exposed on wall2025 ( 25 mm OD) pipe

18.2.1 : Providing and fixing Polyethelene - Alumininum - Polyethelene ( PE-AL- PE) Composite Pressure Pipes conforming to IS-15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C� including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete of joints complete as per direction of the Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.1216 (16 mm OD) pipe

18.2.2 : Providing and fixing Polyethelene - Alumininum - Polyethelene ( PE-AL- PE) Composite Pressure Pipes conforming to IS-15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80C� including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete of joints complete as per direction of the Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.1620 (20 mm OD) pipe

od245330/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification.Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.40 mm dia

od245331/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification. Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.<br>75 mm dia

od245332/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification. Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.<br>110 mm dia

od245333/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification. Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.<br>160 mm dia

od245334/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification. Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab75 mm dia for rain water/vent pipe

od245335/2019_2020 : Supply, installation, testing and commissioning of SWR pipes conforming to PVC IS 13592 Class B for 75mm dia and above, & 6kg/sqcm pipes for pipes below 75mm dia and uPVC IS 13592 Class A pipes for rain water & vent piping including necessary fittings and accessories clamped in position & jointing with O-rings, supports, brackets,etc. for above the ground installation(shafts/suspended) all inaccordance with the drawings and specification. Pipe supporting/ Clamping details:- For vertical shaft piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted (2.5mm) rails& rail legs. For suspended piping, pipes shall be clamped/supported by using 8mm GI "U" bolts to heavy duty GI slotted rails(2.5mm) & slotted rails shall be suspended using 10mm threaded road, 10mm angle fastner, nuts & washers to the slab.<br>110 mm dia for rain water/vent pipe

od245367/2019_2020 : Supply, installation, testing and commissioning of concealed drainage system (soil & waste water pipes) PVC pipes confirming to IS 13592 Class B including necessary fittings, accessories, supports, brackets, etc including cutting the wall /slabs/surface and making good the wall after installation all in accordance with the drawings and relevant standards.Concealed Piping . 40 mm dia <br>

od245375/2019_2020 : Supply, installation, testing and commissioning of concealed drainage system (soil & waste water pipes) PVC pipes confirming to IS 13592 Class B including necessary fittings, accessories, supports, brackets, etc including cutting the wall /slabs/surface and making good the wall after installation all in accordance with the drawings and relevant standards.Concealed Piping . 75 mm dia <br>

od245382/2019_2020 : Supply, installation, testing and commissioning of concealed drainage system (soil & waste water pipes) PVC pipes confirming to IS 13592 Class B including necessary fittings, accessories, supports, brackets, etc including cutting the wall /slabs/surface and making good the wall after installation all in accordance with the drawings and relevant standards.Concealed Piping . 110 mm dia

od245452/2019_2020 : Supply, installation, testing and commissioning of UPVC under ground drainage pipes conforming to IS 15328 including necessary fittings, excavation, connection to manholes, bedding the pipe in constant intravels, back filling, removing the surplus etc. as per IS:1742-1983 and testing the lines to required hydraustatis pressure for below ground(seware) installation all inaccordance with the drawings and relevant standards. <br>110 mm dia

od245542/2019_2020 : Supply, installation, testing and commissioning of UPVC under ground drainage pipes conforming to IS 15328 including necessary fittings, excavation, connection to manholes, bedding the pipe in constant intravels, back filling, removing the surplus etc. as per IS:1742-1983 and testing the lines to required hydraustatis pressure for below ground(seware) installation all inaccordance with the drawings and relevant standards. <br>160 mm dia

od245543/2019_2020 : Supply, installation, testing and commissioning of UPVC under ground drainage pipes conforming to IS 15328 including necessary fittings, excavation, connection to manholes, bedding the pipe in constant intravels, back filling, removing the surplus etc. as per IS:1742-1983 and testing the lines to required hydraustatis pressure for below ground(seware) installation all inaccordance with the drawings and relevant standards. <br>200 mm dia

od245544/2019_2020 : Supply, installation, testing and commissioning of UPVC under ground drainage pipes conforming to IS 15328 including necessary fittings, excavation, connection to manholes, bedding the pipe in constant intravels, back filling, removing the surplus etc. as per IS:1742-1983 and testing the lines to required hydraustatis pressure for below ground(seware) installation all inaccordance with the drawings and relevant standards.<br>110 mm dia for vent/rain water pipe

od245574/2019_2020 : Supply, Installation, testing and commissioninh of drainage fixtures and accessories including cutting and making good the wall/slab all in accordance with the drawings and relevant standards. uPVC deep seal multiple floor Trap

od245762/2019_2020 : Supply, Installation, testing and commissioninh of 160mm dia outlet rain water outlet costructed with CI body, aluminium ring and grade and SS304 grade screws

od245786/2019_2020 : S.S. frame square or round floor clean out with rubber seal and flat cover & screw for following pipe sizes<br>75 mm

od245917/2019_2020 : S.S. frame square or round floor clean out with rubber seal and flat cover & screw for following pipe sizes*110 mm

od245923/2019_2020 : PVC clean out with accessories for following pipe sizes 75 mm

od245924/2019_2020 : PVC clean out with accessories for following pipe sizes 110 mm

19.7.1.2 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With Sewer bricks conforming to IS : 4885

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

od245934/2019_2020 : Supply, constructing sewer manholes with 20cm thick brick walls in cement mortar 1:6, plastering inside & outside with cement mortar 1:3, 12mm thick with neat cement flushing coat and foundation concrete 20cm thick and forming channels with cement concrete 1:3:6 using 40mm broken stone, providing collars around pipes with cement concrete 1:2:4 using 20mm broken stone, corbels at top courses on two sides and R.C.C slab of 15cm thick with cement concrete 1:2:4 using 20cm broken stone and necessary reinforcement and providing necessary provision for fixing hinged type ductile iron manhole cover, its frame and C.I step as per relevant standards and specifications<br>60X60cm internal diamention & 1.2m average depth manholes with hinged type manhole covers & frames confirming to relevant IS standerds

19.4.1.2 : Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith Sewer bricks conforming to IS: 4885

18.33.1 : Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement:4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

od245959/2019_2020 : Supply and fixing of CI manhole frame and cover of lockable type ( Double Sealed ) over openings of under ground sump, overhead tank,rain water Sump, soak pits. 600X600 mm size - Medium Duty cover ( 2.5 ~10 Ton lod bearing )

od245960/2019_2020 : Supply and fixing of CI manhole frame and cover of lockable type ( Double Sealed ) over openings of under ground sump, overhead tank,rain water Sump, soak pits. 600X600 mm size - Heavy Dutycover ( 20 Ton lod bearing )

19.32.1 : Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FIRE FIGHTING WORKS

od247243/2019_2020 : Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and<br>painting with two or more coats of synthetic enamel paint of required shade complete as required : 200 mm dia

od247244/2019_2020 : Supply, Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 150 mm Nominal Dia<br>

od246181/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 32 mm Nominal Dia

od246182/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 40mm Nominal Dia

od246183/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 50 mm Nominal Dia

od246184/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 65 mm Nominal Dia<br><br><br>

od246185/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 80 mm Nominal Dia<br><br><br>

od246186/2019_2020 : Above Ground Piping: Supply and Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 100 mm Nominal Dia

od246222/2019_2020 : Above Ground Piping: Erection, testing and commissioning of 'MS' C Class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II,supply of elbows, reducers, flanges , Stead Rad, Universal Clamb, Nuts & Bolts, Painting (1 coat Zink Rich Primer and 2 coat Signal Red ) etc. Including cutting, Welding, fixing in / on walls, ceiling by using suitable supports, The pipe shall be painted with one coat of primer and two coats of synthetic enamel paint of approved colour / shade. 25 mm Nominal Dia

od246618/2019_2020 : EXHAUST PIPE<br>Instalation of Exhaust pipe for Diesel engine of 150 mm dia MS C Class pipe and Supply and errection of with mineral wool insulation & aluminum sheet cladding with all necessary item supply and errection

od247741/2019_2020 : Under ground piping : Supply,installation Testing and Commissioning of M.S pipes "C" class of following sizes conforming to IS1239 for pipes up to 150 dia & IS:3589 for pipes above 150 dia with fabricated welded joints with neccessary fittings/ specials. The rate is inclusive of excavation up to a depth of 1.5 m & wrapping the anticorrosive material for buried pipes with coating of Primer and wrapping with 4 mm thick polymer corrosion resistant tape as per IS : 10221 with 15 mm overlap.150 mm dia

od246229/2019_2020 : Under Ground Piping: Erection, testing and commissioning of MS 'C' class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II, such as Supply and Installation of elbows, reducers, flanges etc. Including cutting, Welding, laying under ground, by using suitable supports,and wrapping with polymer corrossion protection tape confirming to IS 10221 with proper overlapping, trimming etc complete. etc. complete Size : 80 mm Dia

od246230/2019_2020 : Under Ground Piping: Erection, testing and commissioning of MS 'C' class Pipes confirming to IS :1239 part - I with malleable specials confirming to IS:1239 part - II, such as Supply and Installation of elbows, reducers, flanges etc. Including cutting, Welding, laying under ground, by using suitable supports,and wrapping with polymer corrossion protection tape confirming to IS 10221 with proper overlapping, trimming etc complete. etc. complete Size : 100 mm Dia

od247787/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :200 mm dia

od247791/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :150 mm dia

od247793/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :100 mm dia

od247794/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :80 mm dia

od247801/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :65 mm dia

od247803/2019_2020 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :50 mm dia

od247805/2019_2020 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required :150 mm dia

od247806/2019_2020 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required :100 mm dia

od247807/2019_2020 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required :80 mm dia

od247809/2019_2020 : Supplying and fixing single headed internal hydrant valve with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Stainless Steel cap and chain as required :

od247870/2019_2020 : Supplying & fixing 63 mm dia Stainless Steel short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required

od247874/2019_2020 : Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636(type-A) as required :

od247875/2019_2020 : Supply, installation, testing and commissioning of Hose Box (Fire Hose cabinet) to accommodate one piece of 63 mm dia fire hose along with one pair of 63 mm dia male & female couplings and one branch pipe. The cabinet is made of MS with glass fronted hinged doors and lock.

od247926/2019_2020 : Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following asrequired. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585<br>20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metalvalve & M.S. Pipe and socket

od247928/2019_2020 : Supplying, installing, testing and commissioning of Ball valves with fittings of screwed end type with ISI mark. Size : 32MM

od247929/2019_2020 : Supplying, installing, testing and commissioning of Ball valves with fittings of screwed end type with ISI mark. Size : 20MM

od247933/2019_2020 : Supply, installation, testing and commissioning of single acting Air Release Valve with screwed inlet 15 mm dia etc.

od247942/2019_2020 : Supplying and fixing of 4 way - 150 mm dia,fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

od247954/2019_2020 : Supplying and fixing of 2 way - 100 mm dia,fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

od247965/2019_2020 : Providing, fixing, testing & commissioning of installation control valve of cast iron body,brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves,MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

od247997/2019_2020 : Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Pendent type

od248004/2019_2020 : Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Upwrite type

od252260/2019_2020 : Supply, installation, testing and commissioning of Sprinkler heads designed to operate at 68 deg. Celcious etc. with necessery fittings etc, complete SIDE WALL Type

od248034/2019_2020 : Supply, Installation,Testing and Commissioning of approved type Rosette plates (Dome type, in one-piece) for Sprinklers below false ceiling area. The Rosette shall be chrome plated & shall be as approved by architects / consultants.

od248102/2019_2020 : MAIN PUMP:Supplying, installation, testing and commissioning of 1620 lpm at 70 m Head Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :<br>(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.<br>(b) Suitable HP Squirrel cage induction motor, TEFC,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.<br>(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.<br>(d) Suitable cement concrete foundation duly plastered with anti vibration pads.

od248123/2019_2020 : DIESEL PUMP:Supplying, installation, testing and commissioning of 1620 lpm at 70 m Head diesel engine driven main fire pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.<br>Suitable cement concrete foundation duly plastered and with anti vibration pads.

od248142/2019_2020 : JOCKEY PUMP:Supplying, installation, testing and commissioning of 180 lpm at 88 m Head electric driven pressurisation pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Jockey Pump)<br>Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS : 1520.<br>Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure,horizontal foot mounted type with Class-'F' insulation,conforming to IS : 325.<br>M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plasteredand with anti vibration pads.

od248148/2019_2020 : Supply , Installation, testing and commissioning of Pressure Switch with required acessaries like taflon tape,etc

od248155/2019_2020 : Supply ,Installation, testing and commissioning of Pressure Guage<br>for automatic operation with required acessaries like taflon tape,etc

od248169/2019_2020 : Supplying and fixing air vessel made of 200 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

od248202/2019_2020 : Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets,center bracket, stockbar of following sizes complete as required.1500 mm dia

od248220/2019_2020 : Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm diaholes with stainless steel flange.

od252294/2019_2020 : Supply, Installation, Testing and Commissioning of Addressable contrl relay module for AHU tripping, address Switch to prgram the modules from 01-99 complete as requierd as per specifiactions.<br>

od248337/2019_2020 : Supply, Installation, Testing and commissioning of Analogue Addressable fire alarm control panel 2 Loops, with provisions for operating as stand alone or in a networked system, having 120 / 200 detectors and devices in one loop, 40 character display board, networking up to 99 control panels etc. Provision for versatile networking (Cu-cable, optic fiber, TCP/IP, visualize GUI compatibility 7 days time, 4 programmable output sounder circuits, Fire and Fault relay, GUI and seamless integration with 3rd party system over Module etc. with Rs 485 Module, RS 232 Module, Active & Passive repeaters, mimic driver modules, 4 way sounder & 4 way relay modules and meets EN 54 requirements and suitable for interfacing with BMS and with graphic software

od248344/2019_2020 : Supply, Installation, Testing and commissioning of Analogue Addressable type repeater panel for the main panel at Main Security Office with all the standard facilities and made functional.

od248423/2019_2020 : Supply, Installation,Testing and Commissioning of adressable Surface Mounted Manual Call Point ( Push Button stations) Single Action type with Gold Plated SPST contacts,Address Switch to program the Manual Pull Station from 01-99 ,complete as required as per specifications.

od248428/2019_2020 : Supply, Installation,Testing and Commissioning of Intelligent Addressable type loop powered sounder cum strbes with 90 db output at 1 metre distance and with realy modules including all accessories like junction boxes,glands,terminating lugs etc as requierd and as approved by the engineer in charge /consultant.

od248476/2019_2020 : Smoke detectors:Supply,Installation,Testing and Commissioning of Analogue addressable Acclimating type Multicriteria Detector (Photoeletric smoke cum Thermal detectors) with mounting based LED, Address Switch to program the detectors from 01-99 with BASE complete as required.

od248508/2019_2020 : Heat detectors:Supply,Installation,Testing and Commissioning of Analogue addressable Acclimating type Multicriteria Detector (Photoeletric smoke cum Thermal detectors) with mounting based LED, Address Switch to program the detectors from 01-99 with BASE complete as required.

od248516/2019_2020 : Supply , Installation , Testing and Commissioning of Fault Isolator Modules to identify the shorted and de-wired detectors and devices in the circuit.

od248556/2019_2020 : Supply, Installation, Testing and Commissioning of Addreesable monitor modules for Sprinkler Flow Switch & WLD Monitoring,Address Switch to program the modules from 01-99 ,complete as required as per specifications.

od248586/2019_2020 : Supply , Installation , Testing and Commissioning of 2 C x 1.5 SQ.MM FRLS PVC insulated and PVC sheathed aluminium armoured multi stranded Copper conductor cable, RED coloured with ISI mark.

od248596/2019_2020 : Providing & fixing flow switch in following sizes M.S.pipe including connection etc as required.

od252311/2019_2020 : Supply, Installation, Testing and Commissioning of Response Indicators complete with all fixing accessories.<br>

od248600/2019_2020 : Supply, installation of in position the signages of "Fire boards approved by Kerala state fire service - size 1ft x 4ft made out of PVC rigid sheet 3mm thick with computer cut PVC non-reflective self adhesive imported vinyl painted on the front of PVC rigid sheet complete with wall mounting arrangements with mirror screws". with lettering ASSEMBLY AREA

od248606/2019_2020 : Supply, Instalation of Signages as per Fire Norms LED TYPE: FIRE EXIT

od248617/2019_2020 : Supply, Instalation of Signages as per Fire Norms LED TYPE: EXIT

od248627/2019_2020 : Supply, Instalation of Signages as per Fire Norms LED TYPE: FIRE DUCT

od248635/2019_2020 : "NO SMOKING" sign boards of sixe (180 X 300 mm

od248638/2019_2020 : Supply of "EVACATION PLAN"

od248684/2019_2020 : Supply of embly Point" and "FLOOR INDICATION "sign board

od248686/2019_2020 : Supply of "CONTROL ROOM "sign board

od248690/2019_2020 : Supply, installation, testing and commissioning of Fire Extinguisher ABC type fire extinguisher ISI mark ,4 kg capacity with initial charger and installation brackets.

od248700/2019_2020 : Supply, installation, testing and commissioning of Fire Extinguisher CO2 type fire extinguisher ISI mark ,4.5 kg capacity with initial charger and installation brackets.

od248747/2019_2020 : Supply, installation, testing and commissioning of 6 Watt. Wall mounted Speakers. (Two way)

od248753/2019_2020 : Supply, installation, testing and commissioning of Fire Alarm Cable - PVC insulated fire retardant copper flexible wire 1 sq.mm with ISI mark.

od248764/2019_2020 : Supply, installation, testing and commissioning of 20 mm dia medium grade rigid PVC conduit ISI mark with elbow, tees, jn: boxes, saddle clip and with necessary fittings.

od248806/2019_2020 : Statutory and Incidental Expanses includes, Drawing Preperation, Obtaining Final NOC

CENTRALISED MEDICAL GAS DISTRIBUTION WITH PIPELINE SYSTEM

od297883/2020_2021 : Oxygen : Full automatic Oxygen Controls (flow 1500 LPM) with liquid oxygen connecton facility (3 SOURCE Control )

od297884/2020_2021 : Oxygen :EXTENDABLE TYPE Oxygen Manifold - 2 banks x 10 cylinders with NRVs, tail pipes etc<br>

od297885/2020_2021 : Oxygen : Oxygen Manifold (Emergency) - 2 banks x4 cylinders with NRVs, Tailpipes and regulating system etc <br>

od297886/2020_2021 : Nitrous Oxide : Fully automatic Nitrous Oxide Manifold Controls (flow 500 LPM)<br>

od297887/2020_2021 : Nitrous Oxide : Nitrous Oxide Manifold -2 banks x 2 cylinders with NRVs, tail pipes etc<br>

od297888/2020_2021 : Nitrous Oxide :2 cylinder Nitrous Oxide Manifold (Emergency Reserve) Contols (With Two-stage regulators)<br>

od297889/2020_2021 : Compressed Air plant : a )Compressed Air system (Air cooled Screw/ Rotarivane Compressor): (10+10HP)@ 8.5 bar or nearest above - 2 nos capable of delivering working pressure of 7 bar net of pipeline losses including following accessories among others: <br>

od297890/2020_2021 : Compressed Air plant : Control panel for 2 no. pump (for cascading & Triplex)<br>

od297891/2020_2021 : Compressed Air plant : Air recevers-1 x 1000 Ltrs.<br>

od297892/2020_2021 : Compressed Air plant : Non return valve-2#<br>

od297893/2020_2021 : Filter System : Air dryer-2 x 40 CFM with Dew point monitor and CO monitor (MEDICAL) <br>

od297894/2020_2021 : Filter System : 4 stage Air filter assembly- 2 x 100 cfm<br>

od297895/2020_2021 : Vacuum plant : Vacuum System : Rated Capacity 5HP -2 Nos. Minimum working vacuum of 450mm Hg complete with cabling and termination including the following accessories among others<br>

od297896/2020_2021 : Vacuum plant : Control panel for 2 no.vaccum pump (for cascading & duplex)<br>

od297897/2020_2021 : Vacuum plant : Vaccum receivers -1# 2000L<br>

od297898/2020_2021 : Vacuum plant : Bacteria filters with secretion traps <br>

od297899/2020_2021 : Vacuum plant : Non return valve-2#<br>

od297900/2020_2021 : Vacuum plant : Silencer (if required) -2#<br>

od297901/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 12mm OD X 0.9 mm thick<br>

od297902/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 15mm OD X 0.9 mm thick<br>

od297903/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 22 mm OD x 0.9mm thick <br>

od297904/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 28 mm OD X0.9 mm thick<br>

od297905/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 35mm OD X 1.2 mm thick<br>

od297906/2020_2021 : Copper pipe(Lioyds certified) EN: 13348 : 42mm OD X 1.2 mm thick<br>

od297907/2020_2021 : Area Valve service units with alarms : O2, Vac-2 Gas<br>

od297908/2020_2021 : Area Valve service units with alarms : O2, M.A, Vac, -3 Gas<br>

od297909/2020_2021 : Area Valve service units with alarms : O2,N2O, M.A, Vac, -4 Gas<br>

od297910/2020_2021 : Ball Valves : 15mm<br>

od297911/2020_2021 : Ball Valves : 22mm<br>

od297912/2020_2021 : Ball Valves : 28mm<br>

od297913/2020_2021 : Ball Valves : 35mm<br>

od297914/2020_2021 : Ball Valves : 42mm<br>

od297915/2020_2021 : Total Outlets Points without Probes :<br>Oxygen<br>

od297916/2020_2021 : Total Outlets Points without Probes :<br>Nitrous Oxide<br>

od297917/2020_2021 : Total Outlets Points without Probes :<br>A4<br>

od297918/2020_2021 : Total Outlets Points without Probes :<br>Vaccum<br>

od297919/2020_2021 : Probes : Oxygen Thread type<br>

od297920/2020_2021 : Probes : Oxygentubing type<br>

od297921/2020_2021 : Probes : Nitrous Oxide<br>

od297922/2020_2021 : Probes : AIR 4<br>

od297923/2020_2021 : Probes : Vaccum <br>

od297924/2020_2021 : Other Accessories : BPC Flow meters<br>

od297925/2020_2021 : Other Accessories : Suction jars with Regulators (wards)<br>

od297926/2020_2021 : Other Accessories : OT Suction Units <br>

od297927/2020_2021 : Bed head panel 1500 mm long with provision for gas outlets and 6nos Electric socket & switch (Electricals to be supplied with BHP)<br>

od297928/2020_2021 : BHP Suction Clamp<br>

od297929/2020_2021 : Monitor Mounting Solution<br>

od297930/2020_2021 : I V stand<br>

od297931/2020_2021 : Oxygen Cylinder (D Type) Full Cylinder<br>

od298193/2020_2021 : "N2O Cylinder ( D Type ) Full Cylinder<br>

od297933/2020_2021 : Master Alarm Panel<br>

CIVIL WORKS-STP

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

22.24 : Providing and applying integral crystalline (dry shake) of hydrophilic in nature forwaterproofing treatment to the RCC structures like basement raft, foundation slab,sewage & water treatment plant slab, warehouses floor, parking structures and watertank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by themanufacturer's specification over the lean concrete of above cited structures. Thematerial shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducingpermeability of concrete by more than 85%, compared control concrete as per DIN1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dryshakeshall be capable of self-healing of cracks up to a width of 0.50mm. The work shallbe carried out all complete as per specification and the direction of the Engineer-incharge.The product performance shall carry guarantee for 10 years against any leakage.

MECHANICAL

od298102/2020_2021 : Bar Screen<br>Supplying, installing, testing and commissioning of required size bar screen of 1 Nos. so as to remove the large sized particles present in the sewage water associated with set of guide angles in MS flat of 6.0 mm thick and 50 mm wide coated with two coats of epoxy kept inclined at 45 degree to the horizontal at 20 mm c/c with one no. hand rack in GI. .Bar rack fabricated from MS bars shall be provided to cover the width of the screen chamber with a racking arm for manual operation. Supply, installation, testing & commissioning of Stainless Steel Perforated, Corrugated Bar Screen with suitable lifting arrangement for Sewage & Effluent , chamber having size of 0.6 L x 0.6 B x 0.8 H or as per site condition<br>

od298103/2020_2021 : Raw Sewage Pump<br>"Supply, installing, testing and commissioning of non-clogging type self-priming submersible type sewage transfer pumps(1 working & 1 standby) with cutter arrangement for constant feed of sewage from equalisation sump to aeration tank . The rate quoted shall be inclusive of:Including dry run protection. Industrial type electronic liquid level controllers (with wiring) to control the level of pump automatically. with stainless steel probes / sensors or float switch for automatic operation. Required numbers of pressure gauges, butterfly valves, check valves, unions, flexible connections, pump failure alarm indicator etc.<br>H.P. / K.W. : 1.0 / 0.75<br>Type : Horizontal, Three Phase, Self, Priming, Coupled, Non-Clog with Mechanical Seal<br>Rating :5-6.0 m3 / hr @ 12.0 meter<br>Suction / Delivery (mm) : 40 x 40"<br>

od298104/2020_2021 : Sludge Return Pump<br>"Supplying, installing, testing and commissioning of non-clogging type self priming Return sludge pumps (one working + one standby) to pump sludge from primary settling tank to aeration tank. The rate quoted shall be inclusive of:Including dry run protection. Industrial type electronic liquid level controllers with stainless steel probes / sensors or float switch for automatic operation. Required numbers of pressure guages, butterfly valves, check valves, unions, flexible connections, pump failure larm indicator etc<br>H.P. / K.W. : 1.0 / 0.75<br>Type : Horizontal, Three Phase, Self Priming, Coupled, Non-Clog with Mechanical Seal<br>Rating :6.0 m3 / hr @ 12.0 meter<br>Suction / Delivery (mm) : 40 x 40"<br>

od298105/2020_2021 : Air diffusion system<br>"Supplying, installing, testing and commissioning of suitable capacity Twin Lobe design type air blower, 2 nos(One working + one standby) complete with motors, pulleys, One piece rigid CI casing and side plates, silencer, Acoustic enclosures, base plate, Anti-friction bearings, Rotary oil sealings having horizontal configuration. The rate quoted shall be inclusive of: Including dry run protection. Required numbers of pressure gauges, butterfly valves, check valves, unions, flexible connections, pump failure alarm indicator etc. Twin lobe type rotary air blowers (1 working & 1 standby) with motor and all accessories.<br>Type :Rotary Twin Lobe<br>Rating :60m3 / hr @ 0.4 kg. / cm2<br>B.H.P. :2.5<br>Rating :3.0 H.P<br>RPM :1500"<br>

od298106/2020_2021 : Fine Bubble Diffuser<br>"Supplying, installing, testing and commissioning of fine bubble diffuser with 90mm dia x 1000mm long with membrane, Shall consists of set of EPDM membranes, SS 304 clips PVC support pipe,PVC fitting, nylon rope braided hose with all accessories .<br>Type : Tube<br>MOC : EPDM<br>Capacity : 5.0 m3 / hr <br>Size in mm: 9'0mm diax 1000mm long<br>Design Flow 1.5-3.0 SCFM (2.5-5.0 Nm3/hr)<br>

od298107/2020_2021 : Coarse Bubble Diffuser<br>"Supplying, installing, testing and commissioning of coarse bubble duffuser with 90 mm dia X 800 mm long of HDPE pipe grid with necessary orifices HDPE pipe of 6.0 kg / sq.cm pressure rating with removable deflector to provide clog-free air<br>Type : Tube<br>Capacity : 5.0 m3 / hr <br>Size in mm: 90 mm dia X 800 mm long<br>Design Flow 1.5-3.0 SCFM (2.5-5.0 Nm3/hr)<br>"<br>

od298108/2020_2021 : MBBR Media<br>"Supply and filling of cylindrical shaped specially designed floating bio media / MBBR Media inside aeration tank.<br>Type : Cool Float Random<br>Thickness :20.0 mm<br>Effective Specific Surface area 400m2/m3<br>Media height 15mm/10mm<br>Media diameter 22m<br>Weight per unit surface area 0.37kg/m2<br>Specific graving 0.90 - .095 g/cmc<br>Voidage >98%<br>Density .93g/cm3<br>Media fill rate range 25 – 55% of volume"<br>

od298109/2020_2021 : Tube Settler<br>"Supply and filling of Hexagonal Chevron shaped tube settler media specially designed provides a large settling surface Area within the Specified Volume thus giving high flow rates inside Clarifies/Settling Tanks<br>Type : Hexagonal Chevron Shaped<br>Thickness : 1.1 Mm"<br>

od298110/2020_2021 : Filter Feed Pump<br>"Supplying, installing, testing & commissioning of filter feed water pumps with motor, Horizontal, Mono bloc with Mechanical Seal with all accessories, level controller (with wiring) to control the level of pump automatically. (1 working + 1 standby) <br>H.P. / K.W. : 1.02 / 0.75/ Single<br>Rating : 5.0 m3 / hr @ 20.0 meter<br>Suction / Delivery (mm) : 50 x 50"<br>

od298111/2020_2021 : Pressure Sand Filter<br>"Supply, installation testing and commissioning of sand pressure filter with Multi Port valve, filter shall include standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker, with sand media for filtration of Treated sewage water. The filter shall be suitable for 5.0 m3/Hr flow rate and designed to operate for 10 hours and remove suspended solids in treated water. The SPF shall be designed for a specific velocity of 8 cu.m / hr / sq.m area and the approx dia shall not be less than 600 mm dia. Filter units shall comply with following requirements: Back wash duration - 15 minutes Multi grade Pressure Sand Filter<br>Capacity : 5.0 m 3 / hr <br>Size of filter (mm) : 24(Dia.) x 72inches(Ht.)<br>Material of Construction: Poly glass<br>Operating pressure :6bar<br>Media : Quartz /Fine sand and Graded pebbles<br>"<br>

od298112/2020_2021 : Activated carbon Filter<br>"Supply, installation, testing and commissioning of activated carbon filter for filtration and removal of colour sewage water. The filter shall be suitable for 5 m3/Hr flow rate and designed to operate for 10 hours and remove suspended solids in treated water. The SPF shall be designed for a specific velocity of 8 cu.m / hr / sq.m area and the approx dia shall not be less than 600 mm dia. Filter units shall comply with following requirements: Back wash duration - 15 minutes Pressure dp across unit. - 1.0Kg/ sq.cm (max) Inlet turbidity - 1.00 as NTU Activated Carbon Filter<br>Capacity : 5.0 m 3 / hr <br>Size of filter (mm) : 24 (Dia.) x 72 inches(Ht.)<br>Material of Construction: Poly glass<br>Operating pressure :6bar<br>Media : Quartz /Fine sand , Graded pebbles and Activated carbon(Iodine Value 900mg/gm)"<br>

od298113/2020_2021 : Dosing System<br>"Supplying, installing, testing & commissioning of solution dosing system with tank with inlet / outlet connection, piping & valves along with pump. (Alum, paustit, chlorine)<br>Type : Electronic<br>Flow Rate : 6 Lph @ 4 kg. / cm2<br>Tank Make : Syntex<br>Capacity : 75 Ltr<br>Tank MOC : HDPE"<br>

od298114/2020_2021 : Bio Media<br>"Supply and filling of Bio dek media for biological fixed film systems provides a large surface area for the growth of bacteria<br>Model : FB10.27 Specific surface area : 102 Void ratio : > 97 Dimensions : 1200 x600x600mm material : PVC "

od298116/2020_2021 : Supply and erection work of all Electrical material and work up to the battery limit of the STP plant. <br>

od298117/2020_2021 : Plumbing Work<br>Supply,installation, testing and commissioning of Plant Piping with UPVC 10 Kg/sqcm pipes with fittings and approved make valves, gauges, instrumentation etc., for all plumbing lines and MS B Class pipeline with fittings for Blower Air Lines.<br>

od298118/2020_2021 : UF System<br>Supply erection and commissioning of UF system including all the pumps( feed and back wash),valves and fittings,pressure gauge,dosing pump, rota meter,Electrical actuator valve, and pressure switches Uf System :UF3 -MSPC Feed : 5m3/hr Auto valve : 5no,Audco/equivalent <br>

CIVIL WORKS- BIO GAS

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.26.2 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.Ordinary or hard rock

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.35 : Add for using extra cement in the items of design mix over and above the specified cement content therein

6.1.1 : Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

od298196/2020_2021 : Providing and fixing DI manhole cover with frame 560 mm diameter D.I. cover (Light duty) in concrete slab over manholes/ Inspection Chambers/ Drains, including cost and conveyance of all materials, all labour charges, all taxes, lead, lift, sundries, etc., complete. as directed by the Engineer- in-Charge<br>

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

od298197/2020_2021 : Supplying and fixing 250 mm dia PVC pipe from Inscpection chamber to Fermetation Tank gas out let connections including control valves, all plumbing works etc

18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes

18.8.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal outer dia pipes

od298198/2020_2021 : Supplying and fixing 24 cft biogas burner including all connections, control valves & all plumbing works etc

od298199/2020_2021 : Supplying and filling cow-dung with equal quantity of water for bacteria formation

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.5 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

od246562/2019_2020 : 1 run of UTP 4 pair CAT 6 LAN cable to be drawn in existing surface/recessed steel/PVC conduit as required

od246563/2019_2020 : Cat 6 RJ 45 outlets to be fixed on existing modular face plates and including termination of Cat 6 cables on the outlets

od246564/2019_2020 : 24Port fully-loaded patch panel

od246565/2019_2020 : 42U Rack with cable manager and all other accessories

od246567/2019_2020 : 9U Rack with cable manager and all other accessories

od246568/2019_2020 : Fiber Optic Cable 6 core SM Indoor / Outdoor Cable including splicing and termination at both ends

od246570/2019_2020 : LIU 06 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od246571/2019_2020 : LIU 12 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od246572/2019_2020 : 30pair Krone module fixed in box

od246573/2019_2020 : 100pair Krone module fixed in box

od246574/2019_2020 : IP based Dome Camera with Fixed Lense

od246575/2019_2020 : Indoor Bullet camera, HD 720p, POE SD/SHDC slot 1.3” progressive scan CMOS, 3-12mm lens, H.264, multiple streams, video motion detection, camera tamper alarm, edge storage events, ONVIF compliant, wall / ceiling mount bracket

od246578/2019_2020 : Managed POE 2 switch - 24 Ports 10/100/1000Mbps + 2 1G ports +1 module

od246579/2019_2020 : Layer 3 Managed switch - 8 Ports 10/100/1000Mbps,Pig tail, 18 nos 1G SFP Module,Patch cords ,with all required accessories

od246581/2019_2020 : Supply, Installation, Testing and Commissioning of 6U Rac

od246583/2019_2020 : 32” LED display with wall mount bracket

od246585/2019_2020 : Supply, Installation, Testing and Commissioning of Desktop (i5 , 8GB Ram , 1TB Storage with 22 inch monitor 1 nos .The system should have capability to cater to 1 monitor

od246586/2019_2020 : Video Management Server client software capable of catering to 64 camera

od246587/2019_2020 : 32 Channel NVR with support for 2MP cameras and storage @15 fps & 720P resolution for 30 days

od246588/2019_2020 : Supply and installation of 4 Pair Cat6 UTP Cable for IP based camera

od246589/2019_2020 : Supply and Surface Laying of 25 mm PVC Conduit FRLS White colour

od246592/2019_2020 : Armoured fiber Multi mode cable indoor

od246594/2019_2020 : Supply, Installation, Testing and Commissiong of 6 W ceiling Mount Speaker

od246595/2019_2020 : Supply, Installation, Testing and Commissiong of 6 W Wall Mount Speaker

od246596/2019_2020 : Supply, Installation, Testing and Commissiong of 12 W Horn type Speaker

od246598/2019_2020 : Supply, Installation, Testing and Commissiong of 240 W all in Amplifier

od246600/2019_2020 : Supply, Installation, Testing and Commissiong of single zone call station with microphone.

od246603/2019_2020 : Supply, Installation, Testing and Commissiong of 480 W Booster Amplifier.

od246604/2019_2020 : Supply and Surface laying of 2 core 1.5 sq. mm Cu. Armoured FRLS cable(Yellow colour)

od246608/2019_2020 : TV point wiring with RG-6 cables to be drawn in existing surface/recessed steel/PVC conduit as required

od246609/2019_2020 : Coaxial outlet for TV point

od246611/2019_2020 : Supply, Installation, Testing and Commissioning of finger print & card based stand alone TCP/IP based access control device with all accessories

od246612/2019_2020 : Supply, Installation, Testing and Commissioning of finger print & card based exit reader with connectivity interface for above mentioned controller

od246616/2019_2020 : Supply, Installation, Testing and Commissioning of Biometric Reader for Time Mangement System

od246619/2019_2020 : Supply, Installation, Testing and Commissioning of Single leaf EM lock

od246621/2019_2020 : Supply, Installation, Testing and Commissioning of Emergency Door Exit

od246622/2019_2020 : Supply, Installation, Testing and Commissioning of Access Software with time management software

od246623/2019_2020 : Supply, Installation, Testing and Commissioning of Work station for the above software

od246624/2019_2020 : Supply and Surface laying of 8 core x 0.75 sq.mm FRLS armoured cable ( Black colour)

od246625/2019_2020 : Supply and Surface laying of 4 core x 0.75 sq.mm FRLS armoured cable ( Black colour)

od246097/2019_2020 : DX SYSTEM

od246161/2019_2020 : 3.0 TR Medium Static Ductable

od246173/2019_2020 : 2.0 TR Medium Static Ductable

od246223/2019_2020 : Supply, testing and commissioning of interconnecting hard drawn copper refrigerant piping in brazed construction, including elbows and other necessry fittings duly insulated with chemically cross linked closed cell Nitrile rubber tube insulation, fire retardant grade, outer factory fabricated jacket, duly clamped and supported on GI perforated cable tray as per the drawing and site conditions for connection between outdoor and indoor units. (Liquid & gas lines combined)

od246228/2019_2020 : For 3.0 TR Units

od246238/2019_2020 : For 2.0 TR Units

od246257/2019_2020 : Suppl, testing and commissioning of condensate drain UPVC piping as per BIS 4985 with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell ntrile rubber insulation, fire retardant grade as per the drawing and relavent standards.

od246274/2019_2020 : CONDENSATE PIPING-32mm dia

16.12.1.1 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006

16.12.1.2 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006

od246340/2019_2020 : ACCOUSTIC INSULATION-Supply, installation and testing of acoustic lining with 10 mm thick open cell nitrile foam on the inner side of ducting including providing, fixing and finishing the same as per specifications for ducts as required density of material shall be 140-180 kg/cubm

od246351/2019_2020 : THERMAL INSULATION-Supply, installation and testing of thermal insulation of ducts using closed cell Nitrile Rubber insulation with recommended adhesives and sealed with self adhesive 3mm thick tape and density of material shall be 40-60 kg/cubm.

16.15 : Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

16.16.a : Supplying and Fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

16.18 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

16.13 : Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

od246385/2019_2020 : Fresh Air Louver

od246397/2019_2020 : 350 CFM @ 100Pa ESP

od246400/2019_2020 : 300CFM inline fan

od246402/2019_2020 : 150CFM inline fan

od246429/2019_2020 : 150mm disc valve-Supply, installation, testing and commissioning of powder coated extruded aluminium Extract air disc valves with MS volume control damper as per drawing and relevant standards.

od246431/2019_2020 : Extract Louver

od246432/2019_2020 : Return Air Grill

od246433/2019_2020 : 4C 16.0 Sqmm AYFY Cable + 10 SWG copper

od246434/2019_2020 : 4C 6.0 Sqmm AYFY Cable + 10 SWG copper

od246435/2019_2020 : 3C 1.50 Sqmm Copper Cable

WATER TREATMENT PLANT - CIVIL WORKS

od248226/2019_2020 : Supplying, installing, testing and commissioning approved make Filter Feed pump for feeding water to the Filtration Plant including all required suction and delivery piping; valving, pressure gauges etc complete.Filter Feed pump 1W+1S.Flow rate = 5000 Litres/Hr.Head: 30 m,Power : 1.5 HP (Approx. per equipment)

od248579/2019_2020 : Supplying, installing, testing and commissioning approved make Raw Water Iron Removal filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of under bed & multi -grade filter media to suit the requirement etc. complete as per standards.Raw Water Iron Removal filter with necessary Accessories Max flow rate = 5000 Litres/Hr,Max working Pressure = 3.5 kg/sqmm.,Size: 32 inch Dia,MoC: FRP,

od248581/2019_2020 : Supplying, installing, testing and commissioning approved make Raw Water Pressure sand filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of under bed & multi -grade filter media to suit the requirement etc. complete as per standards.<br>Raw Water Pressure sand filter with necessary Accessories Max flow rate = 5000 Litres/Hr,<br>Max working Pressure = 3.5 kg/sqmm.,<br>Size: 32 inch Dia,<br>MoC: FRP,<br>

od248609/2019_2020 : Supplying, installing, testing and commissioning approved make Raw Water Activated carbon filter with necessary Accessories complete with Frontal Piping, valves, suitable supports for mounting pressure gauges, orifice plates. The cost of filter shall also include initial charge of under bed & multi -grade filter media to suit the requirement etc complete as per standards.<br>Raw Water Activated carbon filter with necessary Accessories complete<br>Max flow rate = 5000 Litres/Hr,<br>Max working Pressure = 3.5 kg/sqmm.,<br>Size: 32 inch Dia,<br>MoC: FRP,<br>Media: Activated Carbon: 1100 IV<br>

od248682/2019_2020 : Supplying, installing, testing and commissioning approved make Treated Water Transfer Pump including all required suction and delivery piping & valving, pressure gauges etc complete. MoC of the pump shall be CI, Configuration 1W+1S<br>Treated Water Transfer Pump including all required suction and delivery piping & valving, pressure gauges etc complete.<br>Flow rate = 15000 Litres/Hr,<br>Head: 25 m,<br>

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.41.2 : Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

12.51.1 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

13.48.3 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

od248683/2019_2020 : Providing and applying standard Epoxy coating over concrete cement Surface with all materials and labour as per design approved by engineer in-charge.

WATER TREATMENT PLANT - ELECTRICAL WORKS

od248629/2019_2020 : Supplying, installing, testing and commissioning Electrical Control Panel Suitable for Auto/Manual operation. The panel shall have Switch gear, MCB, OLR, Single Phase Preventer, H/L Protection, Push Button, Indication Lamp etc. of approved make.

External Works

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.9.1 : Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

51.2.3 : Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

16.91.1 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design& pattern.

16.68 : Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm)

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

16.59.1 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Mandatory / Regulatory sign boards of 900 mm diametre with support length of 3750 mm

16.59.2 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

16.62 : Providing and applying 2.5 mm thick road marking strips ( retro - reflective ) of specified shade / colour using hot thermoplastic material by fully / semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil grease and foreign material etc. complete as per direction of Engineer - incharge and accordance with applicable specifications .

19.6.2 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:150 mm dia R.C.C. pipe

19.6.4 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:300 mm dia R.C.C. pipe

16.65 : Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-Charge.

MODULAR OT

od242877/2019_2020 : Fixing of Ceiling - Ceiling Paneling with 50mm thick HPL Puf Panel properly fixed to the ceiling with Screws and Fasteners. All the joints shall be filled with Silicon

od242899/2019_2020 : Prefabricated Modular Operating Room walls - Wall Paneling with 50mm thick HPL Puf Panel properly fixed to the ceiling with Screws and Fasteners. All the joints shall be filled with Silicon

od242912/2019_2020 : Self Leveling of Floor - Self leveling of Floor about 2-3 mm thickness to make it water level all across

od242925/2019_2020 : Conductive Flooring with covings on bottom corners - Conductive Vinyl Flooring: 2 mm thick ,with perfectly curved flash covings,all joints welded as per the colour and pattern approved by client&lt;br&gt;Make : Gerflor

od242943/2019_2020 : Fully Automatic Control Panel : Supply, Installation, Testing and Commissioning OT Control Panel, Mounted Flush in the Theatre Wall along with Digital Displays Comprising of the following:1. Day Time Clock (Digital)2. Time Elapsed Clock (Digital)3. Temperature Display4. Humidity Display5. Positive Pressure Status

od242954/2019_2020 : LED X-Ray Film Viewer - Supply, installation, testing and commissioning of two plate x-ray viewing screen designed to provide a high level of control luminescence without flicker (dimming range 3-100%) suitable for 3 films of size 14 x 17.

od242962/2019_2020 : Writing bord - Writing bord of size 36x24 inch

od242975/2019_2020 : Ultraviolet Light - UV lamp fixture made of SS 304 and fitted with 30 w UV tubes.

od242987/2019_2020 : Peripheral Lights - Sterile Grade Led Ceiling Light Fixtures - Recess mounted LED panel light, made of powder coated aluminium body and opal acrylic reflectors. Suitable for class 100 application.(40 watts) size 2x2 ft

od242990/2019_2020 : Pendent - Double arm pendent - ways for 2 movable SS tray with each arm and provision for 6 medical gas points and provision for 12 electrical point

od243003/2019_2020 : Pendent - Singe arm pendent : suficitnt ways for 2 movable SS tray with provision for 6 medical gas points and provision for 12 electrical point

od243016/2019_2020 : Hermetically Sealed H.P.L.Sliding Door - Hermetically Sealed Automatic Sliding Door : Hermetically sealed H.P.L. Sliding Door with a size 5 feet x 7 feet . The view panels shall be of 300 x 300 mm sized 6mm thick glass. The frame and door profile shall be of H.P.L. Steel. The door shall be Automatically operated.

od243023/2019_2020 : Hermetically Sealed S.S.swing Doors - Hermetically Sealed S.S.Manual Swing Door - Hermetically sealedStainless Steel Door with a size 3.5 feet x 7 feet. The view panels shall be of 300 x 300 mm sized 6mm thick glass. The frame and door profile shall be of Stainless Steel. The door shall be Manualy operated.

od243029/2019_2020 : Laminar Air Flow - Split plenum - Vertical Laminar Air Flow Chamber made of 1mm S.S.Sheet of 304 grade sheets with a size 8 feet x 6 feetx1 feet to accommodate 6 nos of Flanch type Minipleat filters to achieve 99.97% clean air inside the operating room.And its bottom grill and opening of 2x2 feet shall be provided in the centre to accomodate OT light

od243034/2019_2020 : Filter - Minipleat Flanch type filters 2nos of 3ft x 2ft x 3inch and 4nos of 4ft x 2ft x 3inch with an efficency of 99.97% clean air &lt;br&gt;

od243045/2019_2020 : Pressure Relief Damper - Pressure relief damper with an approximate size of 10 x 14 inch to ensure any excess pressure has to reliesed above than 15 pascal for the safty of people and equipment inside theatre made of SS leafs and the body shall be GI powder coated

od243053/2019_2020 : Coving - Powder Coated Aluminium Coving on all the top corners to avoid all 90 degree corners

od243062/2019_2020 : Fabrication of M.S.Structure for Fixing Doors - Supply and Fabricaton of M.S.&quot;C&quot; shaped Chanels to fix the Doors in the O/T area,with a suport of M.S. Plate on both end of the chanel and cross support of M.S.&quot;L&quot; angle.

od243070/2019_2020 : Gypsum Work - Gypsum Board work - Supply and Constrction of Gypsum Board wall with support of G.I. Chanels (Saint Gobain) properly fixed with screws and fasteners, with an aplication of double coat putty and Emelsion paint

ELEVATOR

od298541/2020_2021 : 20 PASSENGER BED LIFT without Machine Room Serving 04 Stops

WATER PURIFIER

od298544/2020_2021 : SUPPLY AND INSTALLING OF FOLLOWING INDUSTRIAL 500 LPH UV PLANT AND&lt;br&gt;WATER COOLER PC480, BLUESTAR

INCINERATOR

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od298528/2020_2021 : Supply, Installation, Testing and commissioning I Unit of&lt;br&gt;NOWASTE scientific incinerator &ndash; capacity 150 kg/hour.&lt;br&gt;Effective Height &ndash; 30 meters from ground level including&lt;br&gt;I. Primary Combustion Chamber, Secondary Combustion Chamber, Air Pollution Control Unit &ndash; Wet Scrubber, Emission Stack [Effective Height &ndash; 30.0 meters from G. Level], Supporting Tower, Lightning Protection, Water Pump and accessories

Madathil Enterprises

VETTOOR CONSTRUCTION ENGINEERS PVT LTD

Bidder Name

Madathil Enterprises

VETTOOR CONSTRUCTION ENGINEERS PVT LTD

Vellapally Constructions