Tender no. 27/EDC(s)/2022-23

Amount

11 KV FDR VCB Panel 350/500MVA-400/200/5A

ACSR Rabbit Conductor

11 KV Polymer Pin Insuator with Pin

11 KV Polymer Disc Insulator (B&S) type

11 KV Disc fitting 45 KN

Stay Set GI 16x1800mm

Stay wire GI 7/3.15mm 7/10SWG

Earthing Rod MS 20x2500mm

MS Channel 100x50mm

MS Angle 65x65x6mm

MS Angle 75x75x6 mm

Gi wire 5mm 6 SWG

GI wire 3.15mm 10 SWG

Earth wire GI 7/1.6mm 16 SWG

Cable AL 3x70 sqmm XLPE 11KV

11 KV Cable jointing kit 3x70 sqmm Indoor type

11KV pilfer resistance metering cubical

11 KV Cable jointing kit 3x70 sqmm Outdoor type

Electronic static TVM 11KV RS-232 Port

11KV Gang operating 400A GO Switch

9 KV5 KV LA

GI Earthing Strip 35x6mm

PP clamp SP-23 with N&B

E/W clamp ST Pole SP-23 with N&B

Stay Clamp SP-23 with N&B

Bracing Clamp for ST Pole SP-23 upper side with N&B

Bracing Clamp for ST Pole SP-23 lower side with N&B

Labour

Excavation of earth for pole of size 0.90x0.60x1/6 of pole length for erection of ople in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil.

Erection of following pole in proper level and alignment along with fixing of all accessories X-bracing & clamp as per Respo construction manual.

ST Pole SP-23 Single Pole

ST Pole SP-23 Double Pole

ST Pole SP-23 Tri Pole

ST Pole SP-23 Four Pole

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 Block including cost of cement, sand and stone ballast & back filling of soil and boulders inpit and ramming and proper alignment and leveling.

Fabrication of MS channel angle iron after cutting in required size with drilling of hole upto good finish for top channel bracing and special type bracket etc as per Respo shedule and local approve drawing.

Excavation of earth for stay pit of size 0.60x0.60x1.20 mtr. In all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil.

Fixing, tightning and nuzzling of stay (11KV) with pole and stay rod on required tension.

Grouting of stay in size 0.60x0.60x0.30 mtr. In CC ratio 1:4:8 (1 cement:4 graded stone 20mm nominal size:8 coarse sand) block including cost of cementand stone ballast back filling of soil and boulders in pit and ramming and proper alignment and leveling.

Earthing of supports with MS earth rod of 2.5 meter long by hammering of M.S Road to proper depth and connecting the earth electrod with thhe help of GI wire

Laying, spreading & sagging of 11 KV line complete with binding & jumpering (ACSR Conductor)

Mounting and fixing of fuse set on double pole structure including making of complete connection work

Mounting and fixing of TPMO on double pole structure including making of complete connection work

Construction of PRMC Plinth with size 1.5x1.5x1.1 meter above ground level and 0.6mtr. Below ground level including the cost of material such as cement, brick, sand etc and wire mesh fencing with material

Installation of 11 KV metering cubical in the metering room with grouting and making all connection

Digging of trench of size 06x0.15x1.5mtr and laying of underground 11 KV XLPE cable with making of brick Housing and filling of sand including filling of earth with ramming & repairing of Road including cost of cement and stone blast

Installation of 11KV VCB at structure complete with fixing of accessories of VCB and making it operative at the sub-station

Jointing and fixing of 11KV HS cable end termination kit 3x70 sqmm

Mounting and fixing of LA on double pole structure including making of connections by G.I strip size 35x6mm to each point (excluding cost of G.I. strip)

Guarding of line over telephone/road/LT line crossing as per drawing with 6/8 Swg GI wire including fixing of guarding channel/angle as per Respo manual LT/11 KV/33 KV for 11 KV Line

Providing and fixing of danger board and number plate complete by providing clamp of MS Flat 50x6mm with nut & bolt danger board of MS Sheet 2mm thick 11"x7" (including cost of all material)

Erection, providing and fixing of wire mesh of size 50x35mm around plinth abd toe wall duly welded with frame of M.S. angle iron 35x35x6mm and strip size 35x6mm in mid of each side along with wire mash(width of wire mesh 1.5 mtr,) with the height of 0.5 mtr. above the plinth and 2 mtr. above the toe wall with 1 No. gate and locking arrangement

Trimming/Chopping tree branches falling in between the route of proposed 11KV line