AMC of Rediology

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead - Brick work

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead - RCC Work

Demolishing and disposal of unserviceable materials within 100 metres lead - Unreinforced cement concrete up to 15 cm thickness.

Dismantling doors, windows and clear storey windows, ventilators etc, (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachments etc., complete and stacking them within 100 metres lead - Not exceeding 3 sq.m in area.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10 m including all Operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work - Ordinary soil - Manual means upto 3 m depth.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. Thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc. complete.

Cement Concrete (1:4:8) using 40 mm (0.54 cum) and 20 mm (0.27 cum) and 12 mm (0.09 cum) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layer of not more than 15 cm thick well compacted including curing machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5) using 20 mm (0.54 cum) and 12 mm (0.36 cum) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layer of not more than 15 cm thick well compacted including curing machine mixing, cost and conveyance of all materials etc., complete.

Supply and placing of RCC M20 Design Mix Pre-cast slabs of 80 mm thick, using 20 mm HBG crushed metal 0.80 cum, sand 0.400 cum and cement 350 kgs with water cement ratio of 0.53 (185.50 ltrs/ cum of CC) etc., from any source confirming to the relevent ISI standard including cost and conveyance of all mterials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department, including centering, shuttering charges but excluding cost of steel and its fabrication charges, for finished item of work (APSS No. 402).

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars below 36 mm of Fe 415 (as per IS 1786 - 1979) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire, 2 Nos of 20G binding wire in tandem are to be strictly adhered).

Construction of Brick Masonry in CM (1:5) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls in CM (1:4), using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc., complete.

Plastering in CM using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions

- do - in CM (1:5) 12 mm thick

- do - in CM (1:5) 20 mm thick

Finishing the sides of walls with 1st quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of CM (1:3) 12 mm thick and cement slurry of 33 Kg/ 10 Sqm shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls).

Supply of glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Flooring with Antiskid fllor tiles 1st quality of all series and shades (as per manufacture specification), set over base coat of CM (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including white cement slurry of honey like consistency spread @ 3.30 kgs per sq.m jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab,cement, sand and water etc., complete for finished item of work.

Supply of Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Flooring with Vitrified tiles of 1st quality of following varieties of series and shades set over base coat of CM (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kg per sq.m and joints wiht spacer joints with 3 mm wide jointed neatly with filer materials of cement/ epoxy grout/ white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials etc., complete - for finished item of work.

Supply of Double charged (with double layer pigment)/ multi charges stain free full body porcelain vitrified tiles of size 600X600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Part 1 to 15) of any colour and finish in all shades and designs.

Conveyance charges for machinary for transporting earth/ sand/ gravel etc. by tippers/ trucks, with a lead up to 2 kms., including loading, unloading and idle hire charges etc., complete as directed during execution.

Supplying and fixing in position MS Ornamental grills for windows and ventilators or for veranda openings using MS Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with two coats with Synthetic enamel paint over a primary coat (Red oxide metal primer) (total three (3) coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply of Mild Steel, Strucutral Steel i.e., Angles, Chanels and I Sections

Supply of MS Tubes & Pipes of all diametres as per IS-1161

Labour charges for fabricating steel works like Window Grills, Compound Wall Grills, Iron Doors, Windows including cost of welding rods, power charges, excluding cost of fixing in position.

Supply of Plain Float Glass 5 mm thick

Supply of Pin headed Glass 5 mm thick

Supplying and fixing of Sun Control film to the glazed windows partition including labour charges, cost and conveyance of all materials etc., complete.

Supply of following Anodised Aluminum/ MS Powder coated fixtures with ISI Mark

- do - Aldrop Sliding door bolts 16 mm x 300 mm long

- do - Tower bolts 10 mm x 150 mm long with ISI mark IS 204

- do - Tower bolts 10 mm x 250 mm long with ISI mark IS 204

- do - Door handles 150 mm long IS 208

- do - Butt hinges 150 mm long IS 205

- do - Heavy Duty alluminium Door stopper

- do - Mild steel (Powder coated) Butt hinges 150 mm long IS 205

Supply of Country/ Wire nails.

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3 : for width of doors 851 to 1,000 mm)

Engaging of Semi skilled/ Unskilled work man for maintenance and emergency works (each per day)

- do - Semi skilled work man : Mason/ Carpenter/ Painter/ Plumber

- do - Semi skilled work man : Welder

- do - Un skilled work men : Man/Woman Mazdoor

Supply and fixing of PVC/ SWR Pipes and fittings as per ISI standards 4 Kgs/ Sq.Cm, including labour charges for laying, fixing and commissioning the PVC Pipes including couplers/ bends/ tees etc., including fixing necessary fittings like bends, plugs, couplers, junctions, tees,etc., with solvent jointing as per standard practice.

- do - 75 mm dia single socket pipe

- do - 110 mm dia single socket pipe

Kadapa slab 50 mm thick and size not less than 0.457 x 0.457 m (BMT-B.02)

Supply of UV Resistant UPVC/ SWR Pipe fittings (as per ISI standrads).

- do - 110 mm dia Plain bend 87.5 Degrees.

- do - 110 mm dia Door bend 87.5 Degrees.

- do - 110 mm dia Single 'Y' (with Door)

- do - 110 mm dia Vent Cowl

- do - 110 mm dia Single Tee

- do - 75 mm Degree Bend

- do - 75 mm Singel Tee (With Door)

- do - 75 mm 45 Singel 'Y' (With Door)

- do - 75 mm dia Vent Cowl

- do - Round Jali

- do - 3" (76.20 mm) Nahany Trap with jali

Providing Unplasticized PVC SWR Rain water downfall pipes for the following dia with ISI:13592 Type -A mark with necessary shoes, bends, collars etc., including making holes in walls, RCC slabs, beams, columns, including fixing with necessary wooden plugs (where it is required pipe clear of wall, wooden blocks of size equal to that of ears of the pipe shall be used), screws, iron clamps of '18' G and making good the same including cost and conveyance of all materials and incidental charges etc., complete as directed during execution

- do - 110 mm dia PVC Pipe with wooden block of size 150mmx50mmx50mm

- do - 75 mm dia PVC Pipe with wooden block of size 150mmx50mmx50mm

Providing impervious coat to exposed RCC Roof slab surface with CM (1:3) 20 mm thick with 500 ml of liquid concentrated micronized cement water proof/ compound/ 100 ml of integral cement water proofing admixture complies with IS: 2645-2003 of approved make per 50 kg bag of cement laid over roof when it is green including cost of all materials, conveyance charges of materials and all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off juctions of wall and slab etc., complete for finished item.

Painting Ready mixed Synthetic Enamel paint in all shades Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/ liter approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete.

- do - Single coat for old wood work

- do - Single coat for old iron/ old plastered surface

- do - Two (2) coats for new wood work/ new plastered surface over priming coat (total three (3) coats) with ready mixed cement primer (water thinnable) for exterior grade-2 for new work.

- do - Two (2) coats for old wood work/ old plastered surface.

- do - Two (2) coats for old iron work

Painting with Acrylic Emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls.

- do - Single coat for old internal walls

- do - Two (2) coats for old internal walls

- do - Two (2) coats for new internal walls over priming coat (total three (3) coats) with ready mixed cement primer (water thinnable) for interior grade-1 for new work.

Painting with Acrylic Exterior Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand loose powdered materials, including cost and conveyance of all materials to work site and all opertional, incidental, labour charges etc., complete for finished item of work as per SS 911 for external walls.

- do - Single coats for old external walls

- do - Two (2) coats for old external walls

- do - Two (2) coats for new external walls, over priming coat (total three (3) coats) with ready mixed cement primer (water thinnable) for exterior grade-2 for new work

Supply and fixing of PVC Sheet for toilet doors including cost of screws, nails, fevicol etc. complete as directed during execution.

- do - PVC Sheet of 1.50 to 2 mm thick.

- do - PVC Sheet of 0.80 mm thick.

Supplying and fixing in position flush doors of different sizes with 30 mm thick flush door shutters, solid bond wood block board type with commercial ply on both faces of standard make conforming to IS 2202, solid core flush doors, with commercial facing both sides with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, single leaf using best Indian country wood (Vepa/ Neredu) frames of size 75 mm x 100 mm with out threshold plate, including cost of MS "Z" Hold fasts of 230 x 50 x 6 mm MS Powder coated Butt hinges of 125 x 65 x 2.12 mm, screws, nails, etc., complete (Excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supply and fixing of Cement Bonded Pre-Laminated Paticle Boards aluminium glazed partitions using 10 mm Cement Bonded Pre-Laminated Particle Boards and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminium sections anodized to 12 to 15 microns and of sections of size 37 mm x 62 mm and 1.50 mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, GI fasteners 100 x 8 mm size for fixing frame to finished wall, plasticpackers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing and direction of Engineer-in-Charge inclusive of cost of Single/ double glass panes and silicon sealant. Fixed windows/ ventilators made of (small series) frame 47 x 50 mm and mullion 47 x 68 mm both having wall thickness of 1.9 ±0.2 mm and single glazing bead of appropriate dimension. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC Profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40kg), GI fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile offrame & sash shall be mitred cut andfusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and adjacent finished walls hall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as perapproved drawing & direction of Engineer-in-charge inclusive of cost of single/ double glass panes, wire mesh and silicon sealent. Three track three panels sliding window with fly proof SS wire mesh (Two Nos. glazed & one No. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window up to 1.75 sqm) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supplying and fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS: 2556 - Part-4 : 1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size CP Fitting with paraller pipe thread confirming to IS: 2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block - 550X400 mm - Single CP Pillar cock

Manufacture as per BIS:12592 (Part 1&2) Supply and delivery of Pre-cast concrtete manhole covers and frames with ISI marking including, loading, un-loading and stacking at site - Heavy duty -10 with 560 mm dia Clear opening.

Supplying and fixing European Water Closet of 1st quality conforming to IS 2556-Part-2-1973 of white glazed with 'S' trap with ISI mark or equivalent brand approved by the department

Supplying and fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supply and fixing of PVC low level system with internal components and short bend : 8 liters capacity single flush

Supplying and fixing white glazed flat back half stall urinals of size 410X265X305 mm, 1st quality comfirming to IS:2556-1995 with standard CP Spreder of overall size 95x95x57 mm confirming to IS:2556 - Part 6, Sec-6-1974 fixed with screws complete Indian make with ISI mark or equivalent approved by the department :

Supply and fixing TV Shape mirror with plastic frame size 609.60 mm x 457.20 mm

SYMET BIB COCK (CAT.No:123) Fancy 15 mm size with deluxe handles, 122 mm long and 110 mm high and 43 mm breadth 12 mm seat dia and replaceable washers, having approx. weight of 105 gms. Provided with Flange of 56 mm Dia.

SYMET PILLAR COCK FANCY (ROMAN HANDLE) (CAT.No: 131-1) (15 mm) 1/2''size with deluxe handles, 125 mm long and 131 mm high and 43 mm breadth 12 mm seat dia and replaceable washers, having approx. weight of 125 gms.

SYMET PUSH COCK 20 mm (CAT.No: 136) with (3/4'') 20 mm BSP Female threads spout 100 mm long and 57 mm high and 33 mm breadth 12 mm seat dia and Spindle movement of minimum 5 mm having approx. weight of 75gms.

SYMET STOP COCK (CAT.No:141) : As per IS 9763-2000 with ISI Mark 15 mm size with male thread deluxe handles, 86 mm long and 90 mm high and 43 mm breadth 12 mm seat dia and replaceable washers, having approx. weight of 90 gms.

Supply and fixing Gunmetal Gate (GM Peet) valve as per IS - 778 Class - I, Indian make heavy type - 15 mm NB Size

Supply and fixing Gunmetal (GM) Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type - 25 mm NB Size

Supply and fixing Gunmetal (GM) Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type - 50 mm NB Size

Supply and fixing of 31.75 mm dia PVC flexible waste pipe of 914.40 mm length of Ist quality

Supply and fixing stainless steel sink of size 36"X18" (914.40X457.20 mm) 1 mm thick with accessories

Supply and fixing SINGLE BOWL Stainless steel sink size 24"X18"X8" (609.60X457.20X203.20 mm) 1 mm thick with accessories

Supply and fixing of orissa pan white glazed WC 1st quality ISI marked confirming to IS:2556 - Part-3-1981 with P or S trap ISI Mark or equivalent brand approved by the department - 580X440 mm

Supply and fixing internal fittings for flush tank Parryplast wonder flush or equivalent

Reparing and over hauling flushing tank

Supply and fixing towel rod (CP) of 24" long and 3/4" dia

Supply of machinery in desilting works guide lines for engaging Excavator - Loader (JCB) (Capacity/ out put of machine 0.24/1 Cum). 1) The owner should transport the JCB to the work spot at his own cost. 2) The Excavator - Loader (JCB) should be able to execavate a minimum of 40 cubic metre of Earth per hour. 3) The Excavator- Loader (JCB) should be able to load 20 tractor as per hour with quantum of 2.83 cubic meter of loose factor per each tractor. 4) The rate per hour is inclusive of all the cost like POL, Transporting of machine, Driver Batta and other incidental charges. 5) The Payment of the Excavator- Loader (JCB) should be paid hourly basis subject to the condition 2 &3 cited above. 6) The Excavator- Loader (JCB) should have the Tacho meter and it should function properly.

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47 mm thickness (Total Coated Thick ness-TCT), Coating : Zinc coating Z120 GSM. Tensile Strength: 300 MPA. (Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Medium Density Fibre Board Interior Grade Both Side Laminated 18 mm Thick

Supply and fixing of Premium make CPVC Pipes and fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes : 1/2" to 2") SDR 13.5 pipes are made from idential CPVC compounds having the same physical properties for Hot and Cold Water (IS 15778 : 2007)

- do - 22.20 mm OD pipe - SDR 13.5

- do - 28.60 mm OD pipe - SDR 13.5

- do - 34.90 mm OD pipe - SDR 13.5

- do - 54 mm OD pipe - SDR 13.5

Supply and fixing of SYMET 2 in 1 Faucet (1 mts. Tube) with hook (Prayag make CAT No.187) as directed during exection.

Supply and fixing of stainless steel SS 304 grade tubes, sections, plates, sheets and pipes of all size and diametres etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using stainless steel welding rods including buffing, polishing, lacquer finishing, to present seamless finishing etc. complete as directed during execution.

Supply of Stain less steel fly proof wire mesh of not less than 20 gauge

Labour charges for fixing door frame and shutter.

Providing weather proof course with Screeding concrete in CC (1:2:4) 25 mm average thickness using 6 to 10 mm nominal size HBG crushed metal chips, screeding duly embedding 24G chicken mesh with necessary overlap etc. and finishing the surface neatly and rounding the edges at parapet walls, columns etc., including cost of chicken mesh, including cost of all materials and conveyance of all materials etc., complete as directed during execution.

Specialised Five Layer System Of Waterproofing Treatment To The Terrace With Following Specification

Providing and laying five layer water proofing cum heat insulation treatment (MIX GUARD HR5) over existing roof slab, all as directed by Engineer-in-charge and as per the following specification : Arresting roof leakage by providing five layer treatment with MIX GUARD HR5 – five layer system of FAB Chemicals or equivalent elastomeric water proofing and heat reflective coating comprising of the following:

A. Surface preparation – Cleaning the whole area with wire brush. Chipping all loose /dead mortar thoroughly. Cleaning the entire area with high pressure water jetting to remove all loose particles/ grease/ oil/ dust/ dirt/ curing compound etc. Surface cracks must be filled with Mix Build GP and wide cracks must be cut and repaired with Mix build SR polymer modified repair mortar.

B) Application of Mix Guard HR5 – five layer system with brush. 1. First layer – MIX PRIME AC-100 Apply base prime coat using Mix Prime AC100 compound which is produced by mixing Mix Prime AC-100 with water and cement at the ratio 2:1:3 (Mix prime AC 100 : water : cement) by volume with a slow speed drill with paddle. This compound shall be applied with sufficient thickness to cover the holes/pores/cracks @ 1 lit/sq.m area (0.35 Lt of MIX Prime AC100/sq.m)

2. Second Layer – MIX MAT GFM 70/50 Mix mat GFM70/ 50 Synthetic fibre reinforced mesh shall be spread on the top of the primer/in mix with Mix prime AC100 in the wet condition and allow to dry for a period of 6 to 8 hours. A minimum overlap of 100 mm to be provided at the joints i.e. at 1.10 sq.m/ sq.m. The Mix mat GFM Mesh shall confirm to the technical specification as per the manufacturers data sheet.

3. Third Layer – MIX PRIME AC Apply one coat of Mix Prime AC water based acrylic primer (with undiluted material) over the MIX mat GFM mesh @ 0.25 Kg/sq.m as a water tight primer in white colour and allow to dry for a period of 6 hours.

4. Fourth layer – MIX GUARD HR (Base Coat) Apply one coat of Mix Guard HR acrylic based water proof and weather proof coating in white colour (with undiluted material) @ 0.50 kg/sq.m as a membrane on top of Mix prime AC and allow to dry for a period of 6 hours.

5. Fifth Layer – Mix Guard HR Extra (Top Coat) Apply one coat of Mix Guard Hr Extra acrylic based fibre reinforced water proofing and heat reflective membrane in white colour on top of Mix Guard HR base coat (With undiluted material) @ 0.50 kg/sq.m. And allow to dry the system for period of 24 hours to allow foot traffic

Note: All the materials namely Mix Prime AC100, Mix Mat GFM70, Mix Prime AC, Mix Guard HR and Mix Guard HR Extra shall be procured for the entire work order quantity based on the consumption/ coverage area as specified in the specification and shall be ensured by Engineer-in-charge. The Mix Guard HR5 layer system shall be carried out as per FAB Specifications.

Tensile strength : 6.00 N/mm2 (ASTM D412 – 87), Adhesion to substance : > 1.5 N/mm2 (ASTM D4541) for MIX PRIME AC100 slurry with HP tiles, cementitious substrate and subsequent layers. Appearance: White/Grey/Terracotta liquid components, Dry film apperance : Joint free membrane. Density : 1.3 gm/cc

Tear strength : > 17 N/mm2 (ASTM D1004-76), Elongation at break : 200% for the system (ASTM D638), DFT of cured membrane : 1500 to 1700 microns, Total Solids content : 68% + 2%, Water penetration : No leak at 7 bars +ve side (DIN 1048), Application temperature : 5 deg C to 50 deg C. Touch dry: 2 hrs at 25 deg C, Recoatable : 6-8 hrs at 25 deg C, Full cure: 7 days

SPECIALISED FIVE LAYER SYSTEM OF WATERPROOFING TREATMENT TO THE TERRACE WITH Roofcare-prc 5 Systems or equivalent ( ROOFCARE PRC 5 (Armstrong) / ZORICOAT PFC 5 (PMCC)/ POWER SAC 5 L (EBT)/ WATERSHIELD 5 LWC.

a). Ist Layer : Black coloured chemcial treatment : Providng and application of one coat of High bonding, flexible bituminous polyurethane blended bituminous coating with – Roofcare prc 5 systems Confiming to ASTM-G 154 -2000 or equavalent Ist Layer diluting with water at 1 : 1 ratio as a primer coat at a consumption of 200 ml per Sqm

b). IInd Layer : Providing and laying of Fibre Mesh 40 GSM, with 1 Mtr width and 50 mm overlap on the primed surface

c). IIIrd Layer : Grey coloured coating : Providing and application of one coat of Acrylic rubberized elastomeric flexible waterproof grey coating with – Roofcare prc 5 systems ASTM-C 836 or equavalent or equavalent diluting with 50% of water at a consumption of 400 ml per Sqm.

d). IVth Layer : white colured coating : Providing and application of one coat of High solid, cold applied, Fibre reinforced acrylic elastomeric waterproof membrane off white coating – Roofcare prc 5 systems Confiming to ASTM-G 154 -2000 or equavalent coating (add the water upto 200 ml) (Consumption of 350 ml per Sqm).

e). Vth Layer : super white reflective coating : Application of one coat of 100% pure acrylic solar reflective pure white coating with Roofcareprc 5 systems Confirming to ASTM -C 297 or equavalent solar refective coating diluting with 20% of water (Consumption of 300 ml per Sqm).

Note : The above treatment will be guranteed for five (5) years.

Specialised Injection Grouting With Cement And Free Flow Additives: a) Drilling of holes with power drilling machine to the required depth (12 mm to 14 mm dia holes). b) Fixing of Rubber Nozzles with cement and quick setting, Rapid hardening compound putty - Rapidstrong qs or equivalent. c) Grouting of holes with 140 PSI Grout pump with cement slurry mixing with Specialized Free flow, Non-shrink Grout additive - RAPIDSTRONG GROUT ADMIX (Armstrong)/ POWER n GROUT ADMIX (EBT)/ CEBEX 100 (Fosroc)/ ZORIGROUT GP1 (PMCC)/ SIKAGROUT ANCHKOR NSQ (Sika)/ WATERSHIELD GROUT ADMIX i.e., 250 Grams per bag of 50 Kgs Cement add required water to make slurry form. d) After completion of grouting, Remove the Rubber nozzles. e) Later sealing of the hole with polymer cement putty - ROOFCRETE AR (Armstrong)/ ZORIGROUT CMG (PMCC)/ POWER n GUARD ARM (EBT)/ WATERSHIELD AR/ Fosroc NITOBOND AR + Cement. For strengthening and seal the porosity of the concrete to arrest the leakages, dampness, leakages of construction joings : (For terrace/ Ceiling/ RCC Retaining walls basedment floorings/ Water tanks/ Reservoirs/ Toilets etc.)

Hire charges for Tractor, including crew, oils, conveyance to site and all other incidental charges etc., complete.

Providing and fixing 28-30 mm thick solid Wood Polymer Composite (WPC) single extruded door shutter with 3 mm top and bottom rigid layer with an overall density of 750 kg/Cum. It will be fixed to the frame using 3 inch/ 4 inch hinges. Minimum of 4 hinges will be required for fixing the door with the frame.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8 mm rigid layer on all the six surfaces. The door frame will have a rebat of 32 mm. Door Frame section of 45x75 mm The two vertical members are to be joined together with the horizontal member using 8x50 mm long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/ assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2 No.s for horizontal member.

Providing and applying wall putty of white cement or polymer or cement based putty of approved make with average 1 to 2 mm thick ness over plastered surface to prepre the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, appling knifing paste filer by puty knife/ muslin pad, air dry for 2-3 hrs, sand with 180 and 320 No. emery paper for the surface preparation inclduing cost and conveyance of all materials to work site and all operatinal, incidental, labour charges etc., complete for finished item of work execluding scaffolding charges - For old work of internal and external walls.

Labour charges for making, fabricating office furniture, racks, work-station furniture, cup-board shutters with plywood/ MDF Sheets, decolam/ veneer laminations including fixing cutting, making, assembling, fixing hinges, fixing fixtures, fixing locks, pasting sheets/ laminations fixing in position with necessary screws excluding cost of materials, accessories, fittings etc., complete.

Providing and fixing precast concrete blocks (interlocking pavers) using not less than M 40 grade paver blocks and thickness not less than 80 mm for medium traffic areas conforming to IS 15658 -2006 in all shapes and designs as per the specification, over sand bed of 20 mm to 40 mm (30 mm average) thickness and compacting with vibrating plate compactor having 3 tonne compaction force there by forcing part of sand underneath to come up in between joints. Final compaction of paver surface to be done after spreading and brushing the fine sand into joints to its final level. The work includes cost of all materials such as cobble stone inter lock pavers, sand etc., labour and equipments such as cutting machine, lift loading & unloading to work site cleariing, bringing required for the successful completion of work as per drawings and Technical Specification Clause 1504 MORD and as directed during execution by the Engineer - in - charge of the work.

Supply and fixing of 12.70 mm heavy duty dia NP Swan neck pillar cock 400 grams