REPAIRS TO FOOTPATH,PAVED FLOOR,GATE AND FENCE AND REPAIRS TO DELINEATOR , SIGN BOARDS AND MISC ROAD FURNITURE AND CERTAIN MAINT WORK IN DAD COLONY AT MILITARY STATION JAMNAGAR

Amount

Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including suface excavation and removing debris outside MD Land complete all as specified and directed.

M & L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L 75mm thick PCC type C-2, 1:3:6 (40mm graded stone aggt) as in path, hard standing, parking floors, etc., complete all as specified and as directed.

Demolition of Stone slabs and tiles (Interlocking ) laid dry of any description or thickness in floors, aprons etc.

M&L 100mm thick PCC type C-2, 1:2:4 (40mm graded stone aggt) as in path, hard standing, parking floors etc finished even & smooth without using extra cement, complete all as specified and as directed.

Machine pressed precas concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 60mm thick M-35 grade etc complete (with grey cement and pigment) over 50 mm thick sand coushioning complete all as specified and directed by Engr-in-charge.

Providing, cement concrete in kerbs type B1, 1:2:4 (20mm rounded or chamfered on edges graded aggregate) having rounded or chamfered on edges including necessary formwork complete all as specified and directed.

S&F PVC (SWR) pipes 160mm single socketed, in any length with rubber ring joints, laid in trenches or in floors

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade A

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A

Dismantling of MS work of any description not otherwise provided for complete all as specified and as directed

S& F Hand rails, Half round or other steel section or core for wooden hand-rail straight portion , drilled and countersunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed,drilling holes,notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling,bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (GdeE- 250) qualityA

S&F MS Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work or of any other section including ornmental CI items for Portions framed and hung as gates, including pintle hinges,stops ,hand-made sliding bolts etc posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire etc,flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

Demolition of brick work or stone/boulder masonry built in cement mortor or cement lime mortor incl all quoins,arches,pillars etc all as specified and directed

M&L Pre cast cement concrete block type C1in 1:3:6 Using 20 mm graded stone aggregate exc 10 CM in widdth and setting in CM 1;6 all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on the external surfaces of brick work/Stone or concrete surface finishing smooth and even without using extra cement.

M&L for preparation of surfaces plastered or unplastered new surfaces on walls and applying two coats of cement base paint over a coat of primer.

M&L PCC (1:3:6) C-2,using 40mm graded stone aggregate in foundation,filling and mass concrete including form work

Dismantling fencing wire mesh any type

Supply only chain link MS Galvanized fencing size or type 75mm x 75mm with 4mm dia wire incl line wire and any type of standarded rails standard bolts incl binding wire (if minimum weight is not available then contractor has to provide next higher weight without extra cost)

Fixing only chain link fencing including line wires,any mesh size and type to any type of standard rails, straining bolts etc incl providing binding wire.

M&L for preparation of new steel surfaces exc 10 cm in width or girth and applying two coats of synethetic enamel paint over a coat of red oxide/zinc primer

M&L 75mm thick PCC type C-2, 1:2:4 (40mm graded stone aggt) as in path, hard standing, parking floors etc. complete all as specified and as directed.

Taking down cement plaster on brick, stone or concrete surface including racking out joints hacking for key scrubbing down with water to receive plaster a, etc complete all a specified.

M & L for preparation of newly plastered or unplastered surfaces including cornices, pilasters etc and applying Finishing walls with 2 coats of synthetic enamel paint of any description exc 10cm in width or girth including priming coat complete all as specified and as directed.

M&L Preparing old decorated surfaces by complete removal of existing treatment, scraping down, washing, rubbing down and stopping of painted surface of walls (Plastered or unplastered surfaces) and applying Finishing walls with 2 coats of synthetic enamel paint of any description exc 10 cm in width or girth including priming coat of complete all as specified and as directed.

S&F in repair Informatory/Identification Sign boards (Double sided) of size 1200 x 1800mm, made out of 3mm thick ACP (Aluminium composite panel) conforming to IS-736, covered with high intensity grade retro reflective sheeting of green colour as per IRC standard meeting back to back with computer cut letters fixed mechanically on boards fixed with nuts and bolts on single frame made of stainless steel tubular pipe of size 40mm, ensuring safety. The entire sign board shall be fixed to two vertical posts made of 16 gauge stainless steel pipe, 3m long by riveting/shouldering, complete all as specified and as directed including taking of old unserviceable existing one.

S&F In repair Informatory/Identification Sign boards (Double sided) of size 1200 x 1500mm, made out of 3mm thick ACP (Aluminium composite panel) conforming to IS-736, covered with high intensity grade retro reflective sheeting of green colour as per IRC standard meeting back to back with computer cut letters fixed mechanically on boards fixed with nuts and bolts on single frame made of stainless steel tubular pipe of size 40mm, ensuring safety. The entire sign board shall be fixed to two vertical posts made of 16 gauge stainless steel pipe, 3m long by riveting/shouldering complete all as specified and as directed including taking of old unserviceable existing one.

S & F In repair Informatory/Identification Sign boards (Double sided) of size 1200 x 1500mm/1200 x 1800mm , made out of 3mm thick ACP (Aluminium composite panel) conforming to IS-736, covered with high intensity grade retro reflective sheeting of green colour as per IRC standard meeting back to back with computer cut letters fixed mechanically on boards fixed with nuts and bolts on existing frame, complete all as specified and as directed .

S & F in repair Informatory/Identification Sign boards frame of size 1200 x 1500mm/1200 x 1800mm and fixed to two vertical posts and two horizontal member made of 16 gauge thick and 40 mm dia stainless steel pipe, 3m long by riveting/shouldering with fitting arrangement of ACP boards complete all as specified and as directed .

S&F in convex Mirror ,ABS/Fiber/Plastic made up of polycarbonate Reflective Mirrors. Make: Pioneer swift Convex mirror 100cm Polycarbonate PS-C100 completeall as specified

Supply and fixing in repairs metal tubular dealineator in repairs made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed

Taking down ceiling/ Exhaust fan of any size/ sweep after disconnecting the wire from existing ceiling rose for repair/ replacing the unsv bearing, gun metal bush or for rewinding and refixing the same after rewinding, cleaning dust, oiling greasing, servicing, and rubber reel with clamp and nut-bolts, washers, lock pin etc as existing including connecting flexible 3 core cable from ceiling rose to connector of fan, painting of fan complete, with white colour synthetic enamel paint by spraying and filling cavaties with pillar, one coat after cleaning all dust etc all as directed spcified by Engineer-in-charge (Note- Bearing, gun metal bush, rubber reel with clamp, nut-bolts. fan condenser, 1.5 sqmm, 3 core copper flexible cable etc shall be measured and paid separetaly as 'Supply Only' and rewinding item paid seperately under relevant item)

Supply only following items:-

(a) Supply only for ball bearing No 6201 suitable for ceiling/ exhaust fans complete all as specified and as directed.

(b) Supply only for ball bearing No 6202 suitable for ceiling/ exhaust fans complete all as specified and as directed.

(c) Supply only for ball bearing No 6203 suitable for ceiling/ exhaust fans complete all as specified and as directed.

(d) Supply only for brass GM bush suitable for fan any sizecomplete all as specified and as directed

(e) Supply only for rubber reel insulator, 3 Nos nut bolt , washer and lock pin complete all as specified and as directed.

(f) Fan condencer, 2.5 Mfd, 240 volts for ceiling/ Exhaust fan including PVC clamp complete all as specified and as directed

(g) copper conductor FRLS cable, 1.5 Sqmm, 3 core, 1100 Volt grade complete all as specified and as directed

(h) Ceiling fan blades (set of three) suitable for any make and size as approved and complete all as specified and directed

(j) Canopy (set of two) suitable for ceiling fan of any make and size as approved and complete all as specified and directed by Engineer-in-Charge.

(k) Ceiling fan Down rods 45 cm long complete as per existing size complete all as specified and directed

M & L for rewinding of ceiling fan of any size with supper enameled copper wire of existing gauge including varnishing and drying complete reassembling & testing complete of size 1200 mm sweep complete all as specified and as directed.

M & L for rewinding of exhaust fan of any size with supper enameled copper wire of existing gauge including varnishing and drying complete reassembling & testing complete of size 230/300/325 mm sweep complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in any position not otherwise specifically provided complete all as specified and as directed.

M&L filling PCC type D2 1:5:10 (40 mm graded stone aggr) as in sunken floor after applying appropriate treatment to side walls complete.

M&L 15mm thick rendering in cement plaster 1:3 with WPC on vertical and horizontal sides of sunken floor incl finished even and smooth w/o using extra cement all as specified.

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded mixed with liquid water proofing compound @ 0.200 litre per bag of 50 Kg of cement complete all as specified and as directed.

M&L Complete preparation of efforescence or wetted internal wall surface using wirebrush to remove all the loose laittence & wash with clean water and applying crack filling as directed on site wet the wall prior to over coating brush apply I primer coat of Dr Fixit primeseal & allow to dry for 4 hours,apply damp proof coating Dr fixit damp guard,blend a mixture of Dr fixit & water in the ratio 1:1:1(Base:harder:water) & brush apply 2 coat over the plastered surface in a span of 4 hours, over coat of walls with the suitable protective (decorative) coating complete all as specified and directed. Make: Dr fixit or Equivalent as directed by Engineer-in-charge

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.

M & L Non skid coloured ceramic tiles 7-8mm thick area of each tiles exceeding .06 Sqm but not exceeding .11 Sqm, in floors etc. set and jointed in neat cement slurry mixed with water proofing liquid compound and pointed in white or coloured grouting chemical to match , over 15mm thick screed bed in CM 1:6 .complete as specified and as directed by Engineer-In-Charge.

M&L Glazed ceramic coloured designer tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 0ver 10mm thick plaster in cement mortar (1:4) complete complete as specified and as directed by Engineer-In-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as directed.on walls etc.complete as specified and as directed by Engineer-In-Charge.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel designed with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face incl particle board core complete as specified and as directed by Engineer-In-Charge.

S&F100mm butt hinges, stainless steel with galvanised mild steel hinge pin,anodised and fixed,tupe B1 complete as specified and as directed by Engineer-In-Charge.

S&F Extruded aluminium alloy handles 150mm long, fabricated type, anodised complete as specified and as directed by Engineer-In-Charge.

S&F Aluminium anodised barrel tower bolts, 150 mm long, of extruded section. complete as specified and as directed by Engineer-In-Charge.

S & F in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engr-in-charge

S&F in repairs Floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece fixed in floor, over all length of cover plate 140mm complete all as directed.on walls etc.complete as specified and as directed by Engineer-In-Charge.

S&F in repair 25mm dia stainless steel curtain rail, cut in required length and size to fit with opening incl fixing on bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed by Engr-in-charge.

S&F in repairs curtain rod side brackets of stainless steel, angular or cantilever type fixed to wall with 02 nos screws on each bracket and fitted screws for fixing curtain rod incl CP/stainless steel carved decorative design plain metal colour nobs with fixing arrangement for curtain rod using a screw complete all as approved and shown by Engr-in-charge.

Cleaning of service water tanks and any type of capacity by removing organic materials & dirt etc. from wall and base after bailing out / opening wash out and plugging inlet pipes and washing the walls and base by applying bleaching powder or any other approved by Engr-In-Charge and filling with fresh water and replacing the top cover in position etc for the following capacities of tanks . (a) Exc 250 but not exceeding 500 Ltr.

(b) Exc 500 but n. exc 1000 Ltrs

S&F in repair stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, etc. complete as specified and as directed by Engineer-In-Charge.

S&F 4mm thick, sheet glass, ordinary quality and glazing with oil putty in square/rectangular n.exc 0.5 sqm in each pane including hacking out old broken&pin glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, all as specified and directed

M&L for 18/ 19mm thick veneered particle board interior grade solid core general purpose type with decorative veneer on one face and balancing white on other side of type 'BB' fixed with screws to timber frame work as in cup board shutters and shelves and like, fixed in repairs ,complete as specified and as directed by Engineer-In-Charge.

S&F 18/19 mm wide 6 mm thick lipping on veneered particle as in cupboard shutter and shelves complete all as directed.on walls etc.complete as specified and as directed by Engineer-In-Charge.

S&F in repairs 2nd class hardwood plain fillet square rectangular in section wrought sawn secured with screws exc 13 & n exc 25 sqcm in section all as specified and as directed by Engineer-In-Charge..

S & F Continuous (piano) hinges mild steel, bright finish or electrogalvanised complete as specified and as directed by Engineer-In-Charge.

S&F Extruded aluminium alloy handles 100mm long, fabricated type, anodised..complete as specified and as directed by Engineer-In-Charge.

S&F Aluminium anodised 75mm hasp and staple ,safety type with hinge pin including bolt to hinge plate and fixed with screws (Make: Crown/Ajanta/Jayant or equvalent)

S&F15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe all as directed.

S&F in repairs bib taps cast copper alloy chromium plated, fancy type, long body, concealed type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed 15mm bore .

S & F in repairs low level PVC valveless, syphonic action type flushing cistern, white with inlet,ball valve float, and handle including brackets, flush pipes to padestal pan including all joints all as specified and as directed by Engineer-In-Charge.

S&F in repairs Brass CP three way wall Mixer for mixing hot & Cold water screwed down for iron pipe and fixed.

S&F in repairs angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions.

S&F in repairs 100mm dia Overhead Shower alongwith 190mm long shower arm casted, fixed to 15mm bore pipe or union. complete as specified and as directed by Engineer-In-Charge.

S&F in repair stainless steel towel rail long complete all as specified and directed by Eng-in-charge.

S&F in Repairs Soap dish fancy type all as specified and as directed by Engineer-In-Charge. Cat No ACN-1131N of Jaquar or eq model of make specified

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white including PVC seat & cover with mild steel chromium plated hinging device (excluding flushing cistern and flush pipe) complete as specified and as directed by Engineer-In-Charge.

S & F Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with , Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan (excluding Flushing Cistern and Flush Pipe), and connected Items, complete as specified and as directed by Engineer-In-Charge.

Supply and fix in repair 75 mm bore PVC (SWR) plain floor trap with CP grating complete all as specified and directed by the Engr-in-Charge

S&F 75 mm dia PVC(SWR) pipes single stacked in any length laid in floor complete as specified and as directed by Engineer-In-Charge.

S&F 110 mm dia PVC(SWR) pipes single stacked in any length laid in floor complete as specified and as directed by Engineer-In-Charge.

S&F 110mm dia PVC (SWR) branch piece, single (single Y) equal or unequal in repairs. complete as specified and as directed by Engineer-In-Charge.

S & F PVC (SWR) bends 110mm dia bore any radius with access door complete as specified and as directed by Engineer-In-Charge.

S & F PVC (SWR) bends 75mm dia bore any radius with access door complete as specified and as directed by Engineer-In-Charge.

S&F 75 mm dia PVC(SWR) gully trap 125/110 mm setting and jointing with solvent cement complete as specified and as directed by Engineer-In-Charge.

S & F Grating doom 100mm dia of PTMT(Minimum weight 25gms) complete as specified and as directed by Engineer-In-Charge.

S & F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete as specified and as directed by Engineer-In-Charge.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, complete as specified and as directed by Engineer-In-Charge.

S&F in-repair tube medium grade galvanized iron 20mm bore with all fittings & fixed complete to walls & ceiling or laid in floors complete as specified and as directed by Engineer-In-Charge.

M&L for precast RCC 1:2:4 type B1 using 20mm graded stone aggregate in cover slabs including necessary form work etc for manholes covers set in CM 1:4 (reinforcement measured seperately) including Demolition of RCC cover slab complete as specified and as directed by Engineer-In-Charge.

M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required including bending and binding with and including MS wire annealed not less than 0.9mm dia complete as specified and as directed by Engineer-In-Charge.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 (for manhole) all as specified and directed as in repairs.

M&L for cement concrete sub base 75mm thick type D-2 1:4:8(40mm graded aggregate) .

M&L Cement Concrete 1:2:4 (20 mm Graded Stone Aggregate) 40 mm thick, as in floors, etc, and finished the Cement Concrete Surfaces Even and fair with outusing Extra Cement, complete all as specified and as directed.

M&L Preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) and applying one coat of white wash complete as specified and as directed by Engineer-In-Charge.

M&L preparation of old painted surfaces of wood/ wood based materials of any description over 10Cm width or girth and applying one coat of synthetic enamel paint etc. complete all as specified and directed by Engineer-In-Charge.

M&L preparation of old painted surfaces of steel/ iron of any description over 10Cm width or girth and applying one coat of synthetic enamel paint etc. complete all as specified and directed by Engineer-In-Charge.

M&L Preparation of old surfaces of wall removing nails including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) , filling undulation and holes with putty and applying one coat of oil bound distemper with roller finish complete all as directed.on walls etc.complete as specified and as directed by Engineer-In-Charge.

sanu enterprise

KRISHNA ENTERPRISE

KEVAL ENTERPRISE

Rameshwar Enterprise

RACON CONSTRUCTION

M/s Punnsons India