KOTLA 20276-32000

Amount

Ordinary Jungle Clearance of both banks of running Disty., Minors and Drains including Boundary road with discharge exceeding 1.5 cumecs but upto 4.5 cumecs

Earthwork Excavation from canal using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts and combined lead upto 30m (As per CSR item no. 6.19) (Cutting)

Excavation of soil using hydralic Excavator and hydralic tractor trolly i/c cutting and loading in trolly and transporting to the embankment locations with all lifts and Leads (lead 7 km ,ist 1km katcha and 6 km pucca)

Extra for laying earth/fly ash as per specifications for compaction in 20 cm layers and dressing,watering, rolling as per specifications for compaction.

Dressingof new Earth work

Earth work for lip cutting for lining of irrigation channels inclusive of all allowances, lead and dressing :(a ) 0 to 1.5m depth

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick- Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres.

Dressing side slopes and preparation of sub grade for linning

Putting 1:3 (Cement:water) cement slurry with cement @ 2.25 kg per sqm on prepared bed and side slopes before laying concrete on bed and side slopes

Cement concrete lining 75 mm thick or less laid manually for irrigation channel using cement concrete M-15with cement content 325 Kg/cum mixed in automatic computerised batching and mixing plant and transported to site in transit mixer with an average lead of 1 km. (For Lining)

Cement concrete lining 75 mm thick or less laid manually for irrigation channel using cement concrete M-15with cement content 325 Kg/cum mixed in automatic computerised batching and mixing plant and transported to site in transit mixer with an average lead of 1 km. (For coping)

Cement concrete lining 75 mm thick or less laid manually for irrigation channel using cement concrete M-15with cement content 325 Kg/cum mixed in automatic computerised batching and mixing plant and transported to site in transit mixer with an average lead of 1 km. (For Sleeper)

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Filling Contraction Joint with special impervious hot pour 12.5mm wide.

Filling expansion joints with special impervious hot pour 12.5 mm wide.

Applying Bitumen Primer coat on side of lining and top of sleeper for construction joint, Expansion Joint & Contraction Joint. Complete in all respect.

LDPE film of 150 micron over sleepers for construction & expansion joints including supply and carriage & loading unloading of all material complete in all respect as per PWD specification and Engineer in Charge.

Dag belling single Kassi stroke minimum 7.5 cm depth.

Earth work involved in dismantling open flume A.P.M. or O.S.M. type outlets with 'H' more than 0.50 m but upto 0.90 m (including excavation, refilling, consolidation and dressing) .

Dismantling O.F., A.P.M. or O.S.M. type outlets consisting of total dismantling with 'H' more than 0.50 m but upto 0.90 m.

Extra labour for dressing bricks on O.F. and A.P.M. type outlets with 'H' more than 0.50 m but upto 0.90 m.

PCC 1:4:8 with Stone Ballast 40 mm gauge using concrete mixer volume metric type

First class burnt brick work laid in cement sand mortar 1:3 in foundation and plinth.

Laying Reinforced cement concrete (M-20) mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrated but excluding steel reinforcement, centering and shuttering in super structure.

Centering & Shuttering for flat surfaces such as roofs, landings, chajjas, shelves etc.

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete.

C. Conc. 1:3:6 (M-10) with stone ballast using concrete mixer volume metric type

Laying Reinforced cement concrete (M-15) mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrated but excluding steel reinforcement, centering and shuttering in foundation and plinth

Making arrangement for lifting of RCC slab with JCB, sleepers, gutka including labour charges at site of work.

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.Ordinary soil, Manual Means, Depth up to 3 m

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications (M15)

Plain/Reinforced cement concrete M25 in sub-structure With Batching Plant, Transit Mixer and Concrete Pump complete as per drawing and Technical Specifications

RCC Grade M 30-For solid slab Using Concrete Mixer Using Batching Plant, Transit Mixer and Concrete Pump For Solid slab super-structureincluding centering and shuttering Height up to 5m

Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and MoRT&H Specifications

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification.

PCC M15 Grade levelling course below approach slab complete as per drawing and MoRT&H MoRT&H specification clause 2700

Painting on concrete surface Providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm.

Drainage Spouts complete as per drawing no. SD/205 and MoRT&H MoRT&H specification clause 2705 with 6 meter long GI 100 mm dia drainage GI light grade pipe (For Bridges)

Reinforced Cement Concrete Crash Barrier Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-40 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH -33022/1/94-DO Ill dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified

Dismantling of brick work in cement sand mortar / lime mortar including T&P scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material. & staking the serviceable material with all lifts & lead of 100 metre (By Mechanical Means)

Painting New letters and figures on black synthetic enamel paint to an even shade on surface

Plain/Reinforced cement concrete M20 in sub-structure With Batching Plant, Transit Mixer and Concrete Pump complete as per drawing and Technical Specifications

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing force. Complete as per drawing and MoRT&H Specifications

Filling expansion joint with special bituminous material of size 20mm wide and approx 375 mm deep in 26.56 bridge slb to provide for horizontal movements and vertical movements all as per approve drawings andspecifications.

Providing and laying of boulder apron laid in wire crates made with 4mm dia GI wire confoming to IS: 280 & IS:4826 in 150mm x 150mm mesh (weaved diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 18 kg, Including excavation for trimming

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth.

12.5 mm thick cement plaster 1:4

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below:-Bajri (Coarse)screened, cleaned and washed and graded from 20mm to 25mm (fromPathankot or approved equivalent quarry)

Bajri screened, cleaned and washed and graded from 6mm to 20mm (from Pathankot or approved equivalent quarry).

Coarse sand screened, cleaned and washed and graded from 3mm to 6mm (fromPathankot or approved equivalent quarry)

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer – in-charge, upto 90 metre depth below ground level. (c)400 mm dia.

Supplying,assembling,lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia. conforming to IS: 12818-2010 including required hire and labour charges,fitting and accessories etc. all complete for all depths as per direction of Engineer-in-charge. (c)200mm Nominal size dia.

Supplying,assembling,lowering and fixing in vertical position in bore well,unplasticized PVC medium well screen(RMS)pipe with ribs conforming to IS: 12818- 2010 including required hire and labour charges,fitting and accessories etc. all complete for all depths as per direction of Engineer-in-charge. (c)200mm Nominal size dia.

Supplying at quarry site of gravel of 1/16" to 1/8" sizes including pouring and packing in the annular space between the pipes assembly and the bore.The gravel should be free from dust,dirt or the vegetables manner as per IS 4097/1967 with latest amendments

Back filling behind abutment,wing wall and return wall complete as per drawing and Techanical Specifications. (A) Granular material

Supply and fixing of well cap having thread to fix on housing pipe complete in all respects. (c) 200 mm internal diameter

Supply and fixing of M.S. Clamp of size to 150 x 12 mm made out of MS flat 1.52 m long suitable to fit housing pipe including the cost nut and Bolts of suitable size complete in all respects.

Development and stabilizing of the tubewell with air compressor of required capacity as directed by the engineer-in-charge including cost of tools, appliances & consumable to the satisfaction of Engineer-incharge. (a)capacity of air compressor 300 cfm at 250 psi

1.8 meter high G.I. barbed wire fencing with 2.4 meter angle iron posts 50x50x6mm placed every 3 meters centre to centre 0.6 meter below ground level, every 15th post, end post, corner post suitably strutted and provided with 12 horizontal lines and two diagonals interwoven with horizontal wires fixed with GI staples, turn buckles etc. including foundation concrete 1:2:4 of size 0.30x0.30x0.75m for each post complete as per technical clause 808 of MORT&H specifications

Iron grated doors, including pintle hinges & arrangements.

Providing and laying 80 mm thick factory made cement concrete interlocking Paving blocks of M40 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-inCharge.

ONKAR SHARMA CONTRACTOR