Fire Fighting Arrangements

Amount

PART - (A) FIRE PROTCTION & DETECTION SYSTEM I ) FIRE WATER PUMPING SYSTEM Supply, Erection, testing & commissioning of Electrical Motor driven main pump, centrifugal horizontal type, with gland packing capable of deliver 2850 LPM at 70 MWC. The pump shall be coupled with TEFC motor of suitable KW with speed of 2900 RPM with all accessories and complete set shall mounted on common base frame. The quoted rate shall include fixing of coupling, coupling guard and foudation bolts etc.

Supply, Erection , testing & commissioning of diesel engine driven common stand by pump, centrifugal horizontal type with gland packing and capable to deliver 2850 LPM at 70 MWC. The pump shall coupled to suitable HP of Diesel Engine radiator water cooled type with speed of 1800 RPM with all accessories including diesel engine control panel and complete set shall be mounted on common base frame. Batteries & battery leads with stand, fuel tank( for 2 hrs operation) with stand and gauge glass, fuel piping with valves also to be fixed.

Supply,Erection, testing & commissioning of electric motor driven Jockey Pump, horizontal, centrifugal type capable to deliver 180LPM at 70 MWC. The pump shall coupled to TEFC motor of suitable KW with speed of 2900 RPM with all accessories mounted on common base frame.

Supply, Erection, testing & commissioning of compartmentalised common control panel for Electrical Motor driven pumps as per technical specification attached with this tender document. All components shall be housed in a common cubicals made of 16 swg. M.S. sheet with required stiffners(if required). The panel shall be powder quoted of approved colour both inside and out side. The pane shall have both bottom and top cable entry provisions and panel shall be mounted on pedestal of 300mm height. The panel should have sufficient(min. 6 nos per pump set) NO / NC contacts for extending the status of fire pumps to the fire alarm panel.

Supply, laying, testing & commissioning of FRLS, PVC outer sheath, steel armoured, aluminium / copper conductor, 1100 Volt Grade power cables with gland etc. The cable shall be laid in tray / hume pipe / in trenches / on walls / floors etc as required. Cables laid out doors shall include the price of earth escavation providing brick and sand protection, refilling and compacting the earth. 3C x 70 sq.mm YFY for main pump

4C x 10 sq.mm YFY for Jockey Pump

12C x 2.5 sq.mm for Diesel Engine

2C x 1.5 sq.mm for instrumentation

GI earthing strips of 50mm x 6mm thick, strips shall run on floor / ceiling / walls, from pump to control panel with necessary accessories as required.

25 Sq.mm single core multistrand copper cable shall be run on floor / ceiling / walls, from the nearest earth bar to the pump control panel with necessary accessories as required.

Supply and installation of pressure gauge, 1/2 inch bottom entry, of suitable range for pump set with ball valves and other accessories.

Supply and installation of Pressure switches, SPDT type, of suitable range for pump sets with ball valves and other accessories.

Erection, fabrication, testing of MS black steel pipe Heavy grade conforming to IS : 1239 Part -1 /3589 including all fittings viz. Elbows, tees, flanges, etc. reduces clamps, MS support dash fasteners etc. including painting the pipe with two coats of approved red oxide primer and two coats of approved red enamel paint and welded joints complete with cutting and making good the complete with cutting and making good the walls, floors or any other surface (For pumping system ). 200 mm NB x 6 mm thk

Supply,Installation, testing & commissioning of CI Gate Valve as pe IS:14846 (PN 16) with matching flanges complete with nuts & bolts. Size 150 mm NB

Size 65 mm NB

Size 50 mm NB

Supply,Installation, testing & commisssioning of swinging type CI Non return Valve as per IS:5312(PN16 rating) with disc and SS hinges complete including matching flanges, nuts & bolts complete. Size 150 mm NB

Size 65 mm NB

Size 50 mm NB(wafer type)

Supply, Installation, testing & commissioning of CI Globe Valve as per IS:9338(PN10 rating) complete including matching flanges, nuts & bolts complete. . Size 100 mm NB

Size 15 mm NB (SS construction)

Supply,Installation, testing & commisssioning of CI Foot valve with Strainer Size 200 mm NB

Size 80 mm NB

Supply & installation of Gunmetal 4 way collecting head with 63 mm dia instantaneous type inlet 150 dia flanged outlet without built in check valve for fire brigade connection to fire water reservoir (IS : 904) with one no. butterfly valve & NRV of 150NB size.

Supply & installation of Gunmetal Fire Brigade Draw out connection with necessary foot valve for reservoir.

PART - (B) FPS SYSTEM Supply, installation, testing & commissioning of CI Gate Valve as pe IS:14846 (PN 16) with matching flanges complete with nuts & bolts. Size 150 mm NB

Size 100 mm NB

Size 25 mm NB(SS construction)

Supply and installtion of swinging type CI Non return Valve as per IS:5312 with flap and SS hinges complete including matching flanges, nuts & bolts confirming to IS 5312 Size 150 mm NB

Size 100 mm NB

Supply,Installation of SS oblique type single headed Hydrant valve with 80 mm inlet and 63 mm outlet GM instantaneous male coupling with rubber cap and chain conforming to IS : 5290.

Supply,Installation of SS oblique type single headed Landing valve with 80 mm inlet and 63 mm outlet GM instantaneous male coupling with rubber cap and chain conforming to IS : 5290.

Supply, installation of automatic 25 NB Air Release Valve

Supply, installation of Globe Valves in Gun Metal Construction to IS: 778 with screwed ends 25 NB size.

Supply & installation of SS branch pipe with 20 mm nozzle conforming to IS : 903 complete.

Supply & installation of 63 mm dia rubberized reinforced rubber line hose pipe in 15 m length conforming to IS : 636 Type I ISI marked with gunmetal male and female instantaneous coupling conforming to IS 903 wounded with 18 SWG copper wire complete.

Supply & installation of MS hose box of fabricated from 16 SWG CRCA sheet double door with lockable arrangements to accommodate 2 RRL hose of 15 m length and one branch pipe painted white inside and red outside with one key. (750x600x250 mm).

Supply & installation of swinging type hose reel drum fabricated from 14 SWG CRCA sheets painted with red colour stove paint 2 coats over 1 coat of primer with 30 m long 20 mm dia rubber hose pipe with 10 kg/sq cm working pressure with SS self closing shut – off nozzle of 5 mm outlet fixed on wall with dash fasteners and necessary shut off valve.

Supply & installation of SS 2 way inlet connection with 63 mm dia instantaneous type inlet 100 dia flanged outlet with built in check valve for fire brigade connection to fire riser ( IS : 904) with one no. butterfly valve & NRV of 100 NB size.

Supply & fixing of Installation Control Valve complete with trims & gong Size 150 mm NB

Supply, erection, testing of MS black steel pipe Heavy Grade conforming to IS : 1239Part - 1/3589 including all fittings viz. Elbows, tees, flanges, etc. reduces, clamps, included with joints complete with anticorrosive treatment to burried pipes by wrapping with two coats of 4mm thick PYPKOTE membrane applied over a coat of primer for external yard hydrant network. 150 mm NB

Supply, fabrication, erection & testing of MS black steel pipe Heavy grade conforming to IS : 1239/3589 including all fittings viz. Elbows, tees, flanges, etc. reduces clamps, MS support dash fasteners etc. including painting the pipe with two coats of approved red oxide primer and two coats of approved red enamel paint and welded joints complete with cutting and making good the complete with cutting and making good the walls, floors or any other surface 150 mm NB

Providing & fixing Butterfly valve as per BS :5155 (Wafer type) matching flanges complete with nuts & bolts. Size 150 mm NB

Supply & fixing of 150NB Flow Switch

Supply & fixing of Sprinkler Head Pendent type

Supply & installation of Gunmetal 3 way collecting head with 63 mm dia instantaneous type inlet 150 dia flanged outlet check valve for fire brigade connection to fire water reservoir (IS : 904) with one no. butterfly valve & NRV of 150NB size.

Supply, erection, testing & commissioning of addressable Multicriteria Detector

Supply, erection, testing & commissioning of addressable Mannual Call point

Supply, erection, testing & commissioning of Hooter/ strobe

Supply, erction, testing & commissioning of Control Module

Supply, erction, testing & commissioning of Monitor Module

Supply, erction, testing & commissioning of Isolator Module

Supply, erection, testing & commissioning of 6 Watt Speakers (Ceiling Mounted )

Supply, erection, testing & commisssioning of Amplifier 200watt with microhone

Supply, erection & testing of 2CX1.5Sqmm FRLS Armoured cable(Loop and Power cable).

Supply, erection & testing of 2CX1.5 Sqmm Armoured cable (PA Cable)

PORTABLE EXTINGUISHERS Supply & fixing of 6 Kg ABC type dry power extinguisher consisting of welded MS cylindrical body with discharge valve, nozzle and hanging arrangement complete conforming to IS: 2190

Supply & fixing of 9 Litre Water type CO2 (ISI marked) extinguisher including all accessories with wall bracket & raw plug conforming to IS:940

Providing & fixing 9 Litre Foam type (ISI marked) extinguisher including all accessories with wall bracket & raw plug confirming to IS:15683 (For pump room)

SIGNAGES Supply and installation in position the "FIRE EXIT" Sign with luminicent colour having size 300 x 100 mm.

Supply and fixing in position the signages " FIRE ORDER" contain the following matter on 3 mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of size 1200 x 1000 mm. a. ALERT THE SECURITY AT SECURITY ROOM BY ACTUATING MANUAL CALL POINT LOCATED AT STRATEGIC LOCATION. b. EVACUATE THE OCCUPANTS BY USING FIRE EXIT AND EMERGENCY EXITS ONLY AND ASSEMBLE AT ASSEMBLY POINTS. c. BE CALM AND DO NOT GET PANIC, WALK DO NOT RUN. d. IF POSSIBLE TRY TO EXTINGUISH FIRE BY USING NEAREST / SUITABLE PORTABLE EXTINGUISHER OR WATER FROM NEAREST WET RISER.

Supply and fixing with prited " In CASE OF FIRE, DO NOT USE LIFT USE STAIRS ONLY" OF 1.5 cm hight letters in red with white background. The size of the board shall be 300 X 250 mm and shall be fixed at the hight of 2 mtrs. From finished floor near Manual Call Point.

PART - (C) CONSTRUCTION OF UNDERGROUND RESERVOIR Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm.

Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Cement concrete with 30 mm down graded shingles excluding shuttering. In ground floor With N.B. Variety stone metal. 1:3:6 proportion

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade Pakur Variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement 35 mm. thick

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4m Tor steel/Mild Steel JSW / JSPL / SHYAM / SRMB / BMASL / ELECROSTEEL / SSL

Extra rate for using water proofing and plasticising admixture @ 0.2% by weight of cement (or at manufacturer's specified rate) for concrete of various grades.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] With 1:4 cement mortar 20 mm thick plaster

Labour for Chipping of concrete surface before taking up Plastering work.

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.

Supplying, fitting and fixing in position C.I. manhole/ pit cover with rim. Round 450 mm X 100 mm X 50 kg (approx.)

Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) Super Protective 100% Acrylic Emulsion.

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

PART - (D) CONSTRUCTION OF DEEP TUBEWELL Labour for boring through any type of soil for sinking tube well of required dia. with top enlargement by rig boring system (either by reserve circulation or by direct rotary method) including hire charges and labour for rig machine, tools and plants, staging, force pumping set and making arrangement for water required for boring etc. complete and lowering of pipes, strainers, blind pipes etc. complete. For depth upto 250 metre for 150 mm dia. Tube well with top enlargement of 300 mm dia.(upto 50 metre.) First 50 metre

Next 50 metre

Next 50 metre

Rest 100 metre

Supplying, fibre glass reinforced Epoxy resin slotted of 1 mm slot width in 6.1m length of approved make and as per direction of the Engineer - in - Charge 100 mm nominal dia 6.00 mm wall thickness

Supplying M.S. male / female adopter of approved make and brand for coupling of M.S. pipe and fibre glass strainers, as per direction of the Engineer - in - Charge. 100 mm

Sypply of E.R.W.M.S.(Electrical Resistant Welded M.S.) black pipe of of TATA make (heavy quality) as per standard specification, 5 mm thick. 200 mm dia. (internal)

300 mm dia. (internal)

Supplying, fitting and fixing chech valve (vertical) G.M. tested to 21 kg per sq. cm. 50 mm

Supplying, fitting and fixing heavy type bell mouth reducing socket. 100 mm X 200 mm

Supplying, fitting and fixing G.I. cap at top 300 mm

Supplying, fitting and fixing M.S socket ring 200 mm

Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with 'V' notch including hire and labour charges for all tools and plants and scaffolding as required.

Labour for making arrangement for showing verticality test including the cost for hire charges of tools and plants, scafolding, labour etc. all complete.

Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction.

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer 5000 litre capacity

1000 litre capacity

Packing the annular space between the outside of the tube well pipes & strainers and the bore with pea size washed gravel of approved quality having size from 2 mm to 5 mm or the size approved by the Engineer-incharge including cost of all materials labour and equipment complete.

Packing annular space between the outside of the housing pipe and the bore with puddled clay balls of approved size as per direction of the Engineer-in-charge with cost of all materials and labour complete.

Providing 200 mm centre guide. With Clamp

Supply & installation of 4H.P. Submersible pump Motor set suitable for 125 mm dia deep tube well capable for discharge 20000 LPG of clear water at a total head of 48 mtr. Having a discharge out - let of 50 mm dia with 4sq mm (Finolex) 3 core PVC Flat copper cable of 35 mtr including LT make DOL starter KSB Model No. Cora 18 C/10.

Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary including supply of necessary report.

PART - (E) CONSTRUCTION OF PUMP ROOM Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Cement concrete with 30 mm down graded shingles excluding shuttering. In ground floor With N.B. Variety stone metal. 1:3:6 proportion

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. Pakur Variety

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade Pakur Variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4m Tor steel/Mild Steel JSW / JSPL / SHYAM / SRMB / BMASL / ELECROSTEEL / SSL

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

In superstructure, ground floor

25 mm. thick damp proof with cement concrete (1:1.5:3) (with graded stone aggregate 10 mm. normal size) and painting the top surface with a coat of bitumen [VG.40 ] using 1.7 kg. per sq.m. including heating the bitumen and cost and carriage of all materials complete. [Bitument to be supplied by the Agency]

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) With earth obtained from excavation of foundation.

Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] With 1:6 cement mortar 20 mm thick plaster

With 1:6 cement mortar 15 mm thick plaster

With 1:4 cement mortar 10 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement 35 mm. thick

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Sal : Local.

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) 40mm X 6mm, 250mm Length

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Shutters of 2/3rd panel and 1/3rd glazed of doors and windows as per design (each panel consisting of a single plank without joint and with ordinary glass of 7.4kg. Per sq.m./3mm thick) fitted with putty bed and teak wood beads and nails including fitting and fixing shutters in position but excluding the cost of glass, putty, teak bead, nails, hinges etc. and other fittings, in ground floor. 35mm thick shutters with 19mm thick panel. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak.

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) 3 mm thick (weighing 7.4 kg/Sq.m)

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. 100mm. X 58mm. X 1.90mm

75mm. X 47mm. X 1.70mm.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: With round base: 150 mm grip x 12 mm dia rod.

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: 150mm long x 12mm dia. bolt.

300mm long x 10mm dia. bolt.

Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. 300mm long

Supplying, fitting and fixing hinge cleat in position excluding the cost hinge and other fiffitngs. with 75mm iron Butt-hinge Local Sal.

Iron catch hook of approved quality fitted and fixed to shutter and chowkat. 10mm dia x 300mm long.

Synthetic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. In Ground floor: Two coats.

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On timber or plastered surface : With super gloss (hi-gloss) - Two coats (with any shade except white)

On steel or other metal surface : With super gloss (hi-gloss) - Two coats (with any shade except white)

Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4)and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e) I (I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment. Light Colour

Cement washing including cleaning and smoothening surface thoroughly (cement to be used @15 kg./100 sq.m. of surface for one coat and @25 kg./100 sq.m of surface for two coats): External surface (Ground floor) One coat

DELTA CONSTRUCTION