EO_GBDA_144_2026_27

Dismantling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres (Reference to MORT&H's specification clause 202) 4.(i) Lime /Cement Concrete (I) By Manual Means (A) Cement Concrete Grade M-15 & M-20

4.(ii) Dismantling Brick / Tile work (B) In cement mortar

Eucalyptus bullah walling with earth filled bags 1.30m (av.) high of 10cm. dia and 3.6m long bullah pin @ 0.375 mtr. c/c bullah walling of 2.7m (av) below G.L. including fitting, fixing 3 nos. of 10 cm dia bullah as runner providing 1.80 mtr. long 10.0 cm dia bullah as tie bar @ 2.25 mtr c/c and 10.0 cm dia. and 3.0 mtr. long bullah as tie post @ 2.25 mtr. c/c driven @ 2.5 m below G.L. and walling with filling empty cement bags with earth and placing them in position including tying or sewing mouth including cost of thread including cost of all materials and two coat of coal tarring to all Eucalyptus bullah etc. complete including the cost of materials as per direction.

Banking excavated earth by mechanical / manual means in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and for all lift : 2.3.1 All kinds of soil

Box cutting or filling in road embankment in all sorts of soils including spreading the spoils properly over the flank as necessary or on berm to approximate grade and camber and rolling the sub-grade with power roller to proper camber and grade as per direction and satisfaction of Engineer-in-Charge icluding uprooting and removing plants and jungles when and where necessary. (a) Depth up to 150 mm

Sand Filling in Foundation Trenches with good local sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304).

Brick edging 75 mm wide with picked jhama bricks, laid true to line and level including cutting necessary trench in soil or in hard metalled surface, laying the bricks and repacking the trench (on both side of the edging) with spoils and ramming the same thoroughly complete as per direction. (b) Brick-on-end edging (250 mm) depth

Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with powdered earth and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction. c) Soling or dry pavement with one brick-on-edge on a layer of brick flat (thicknass 125 mm. plus 75 mm.)

Providing & fixing Concrete Sign Board as per IRC specification of size 900 x 750 x 37 mm. thick made with RCC 1:1½:3 with pakur variety stone chips reinforced with double layer IRC febric (75 x 75 mm. mesh) and fixed with necessary nuts & bolts on two RC precast posts 100 mm. x 150 mm. of height 2.65 m. of which top 750 mm. is of section 100 x 13 mm. and 1.90 metre above GL & 0.75 metre below GL including digging hole, repacking the same with cement concrete 1:3:6 with jhama khoa or with local stone chips etc. complete including painting two coats on both faces lettering sign marks etc. as per direction of the Engineer-in-Charge. (The rate is inclusive of cost of reinforcement, concrete, shuttering, nuts & bolts, washer etc. complete.)