Construction of additional accommodation for Govt. Sr.Sec. School building at Mehandi in Tehsil Karsog Distt. Mandi (H.P.) (SH Construction of Laboratory three class room one store including Stair Case).

Excavation in foundation trenches etc. in earth work lift upto 1.50mtr. stacking the excavated soil not more than 3mtr. clear form the edge of the excavaion and then returning the stacked soil in 15cm layers, when required in to plinths, sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20mtrs in pick jumper work.within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm (Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:-

Foundation footings basis of coloumns etc.and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plain

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor.

Edges of slabs and breaks in floors and walls in any width.

Stair cases with sloping or stepped soffits excluding landing

Providing and laying cement concrete 1:6:12 (One cement : Six sand : Twelve graded stone aggregate 40mm (forty milimeter) nominal size) and curing complete exluding cost of centring and shuttering in foundation and plinth.including carriage of material within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying cement concrete work in 1:2:4 (One cement : Two sand : Four graded crushed stone agg. 20mm (twenty milimeter)nominal size) and curing complete excluding cost of form work in foundation & plinth.including carriage of material within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying M-20 grade of cement concrete mechanically mixed and vibrated with minimum cement content 320Kg./Cum.(Three Hundred Twenty Kilogram Per Cubic Metre) with crushed stone aggregate 20mm(Twenty milimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation footings basis of coloumns etc.and mass concrete.including carriage of material within all leads, lifts and others incidentals as per the direction of Engineer-in-charge.

Suspended floor, roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilever above plinth level upto floor any level. including carriage of material within all leads, lifts and others incidentals .

Columns, pillars, posts and struts above plinth level upto any floor level.including carriage of material within all leads, lifts and others incidentals as per the direction of Engineer-in-charge.

Stair cases (Except spiral stair cases) excluding landing but including preparing of the surface and finising of nosing above plinth level upto floor any level. including carriage of material within all leads, lifts and others incidentals as per the direction of Engineer-in-charge.

Providing and laying floor upto floor two level reinforced cement concrete 1:2:4 (one cement : two Sand :four graded crushed stone aggregate 20mm (Twenty millemetre nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in moldings as in cornices, window sills etc. not exceeding 15 cm (fifteen millimeter) in grith upto any floor level including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto all floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying cement slurry on RCC slab or cement concrete work using 2.75 Kg (Two point Seven Five Killograme) of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surface complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Providing throating or plaster drip and moulding to R.C.C. chajja including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks with rat trap bound in super structure in cement mortar 1:6 (One Cement : Six Sand) Second Class Bricks above plinth level upto floor any level including carriage of material within all leads, lifts and other incidentals.

Brick work using common burnt clay building bricks in cement mortar 1:6 (One Cement : Six Sand ) Second class brick above plinth level upto floor any level including carriage of material within all leads, lifts other incidentals.

Half brick masonry in common burnt clay building bricks in super structure in cement mortar 1:4 (one cement : four sand) Second class brick (i) above plinth level upto floor any level including carriage of material within all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonary (uncorsed/brought to cources) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement : 6sand 12 graded stone agreegate 20mm nominal size) at plinth level in cement mortar 1:6 (1cement: 6sand) within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying precast cement concrete hollow block masonry with cement concrete blocks of size 40cm x 19cm x20 cm (forty centimetre x Ninteen centimetre x twenty centimetre) including quion block jamb blocks and closers etc. made of cement concrete 1:3:6 (one cement : three sand : six graded stone aggregate 20mm (twenty milimetre) nominal size) laid with cement mortar 1:6 (one cement : six sand) including curing complete in any level upto all leads, lifts as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing Fixing 40 mm (forty millimeter thick) frame work 12 mm (twelve millimeter) prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/ black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 300x16mm ( three hundred x sixteen millimeter) anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 200x10mm ( two hundred x ten millimeter) aluminium tower bolts (Berrel type) anodized transparent or dyed to required shade and colour with screws etc complete including carriage of material within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimeter) aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing particle board ceiling of approved quality with butt jointing and nail (frame work and cover fillets to be paid for separately :- Cement bounded particle board 8mm (Eight millemetre) thick as per direction of Engineer-in- Charges within all leads, lifts and other incidentals. .

Providing and fixing M.S. Grills of required pattern in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain grills including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing Glass strips in joints in Tarrazo floors 40 mm (forty millemetre) wide and 4 mm (four millemetre) thick including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge. .

Cement concrete flooring 1:2:4 (one cement :two sand:four graded crushed stone aggregate 20mm (twenty millemetre nominal size) laid in one layer finished with a floating coat of neat cement 40mm (forty millemetre) thick including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Extra for making chequers of approved pattern on cement concrete floors. steps. landings and pavements etc including carriage of materials as per direction of Engineer-in- Charges within all leads, lifts and other incidentals.

Cement plaster skirting (upto thirty centimetre height) with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including rounding of junction with floor 15mm (fifteen millimetre ) thick including carriage of materials within all leads and lifts and other incidentals or as per direction of Engineer-in- Charges .

Providing and fixing 0.60 (Zero point Six Zero) millimetre thick prepinted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyester of 5 five microns over 5 five microns primer coating i/c fixing with preprinted iron J or L hooks, bolts and nuts 6mm (six millemetre) dia meter with preprinted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing ridges or hips 60 cm ( sixty centimetre) overall with 0.60 mm (zero point six zero) millimetre thick prepainted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyester organic coating of 20 (twenty ) microns over 5 (five) microns primer coating + back coat of polyester of 5 (five) microns over 5 five microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm (six millemetre) dia metre with prepainted G I limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in:-

In beams joists channels ,angles ,tee ,flats with connection plates or angle plates as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like including carriage of materials within all leads, lifts and other incidentals

In gratings framed guard bars,ladders,railling,brackets and similar works including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. B.P. Sheet 1.66 (one point sixty six) millimetre to 2mm (two millimetre) thick in eaves board / fascia/ soffits/ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primers complete as per the information of Engineer-in-Charge (base members of steel work shall be measured and paid separately) including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing standard steel section of ISLC and flat iron doors,windows and clerestory window manufactured from ISLC iron section 75x40mm(Seventy five into forty millimetre) with MS flat iron section of 75x4mm (Seventy five into four milimetre) thick including hinges, jambs, lock jamb,beed and if required angle thrashold of mild steel angle 50x25mm(Fifty x twenty five milimetre) welded or righdly fixed by mechanical means,lugs with split end tails to each jambs including steel butt hinges 2.5mm (Two point five millimetre) thick with provision for locking arrangement and sock observer as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by Engineer-in-Charge including carriage of material within all leads, lifts other incidentals.

Providing and fixing standard steel section of M.S angle and flat iron door,window, clerestory window manufactured from M.S angle iron section of 40x40x5 (forty into forty into five) millimetre and 50x5 (fifty into five) millimetr MS flat in combination welded together to make one frame including hinges,jambs,lock jambs beed and if required anglethreshold of mild steel angle 50 x 25 (fifty into twenty five) millimetre welded or rigidly fixed by mechanical means d,lugs with split end tails to each jambs including steel butt hinges 2.5mm (two point five) millimetre thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatnent of the surface as directed by Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing steel glazed framed shutter of Z-section with 4mm (Four milimetre) thick glass panes with putty for doors, windows and clearestory windows required shape and section with fitting and necessary screws etc. including fixing iron hinges with necessary screws including applying a priming coat of red lead paint complete as per approved specification /design.Including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing steel wire gauge shutters in z-Section using galvanised M.S. wire gauge of I.S. gauge designation 85 (eighty five) G. with wire of dia 0.56 (zero point five six) millimetre for doors windows and clerestorey windows including metal beadind of approved quality and shape section with necessary steel screws including applying a priming coat of red lead paint complete as per approved specification / design, including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S.fan clamp type -1 of 16 mm ( Sixteen millimetre) dia M.S. bar bent to shape with hooked ends with R.C.C slab during laying including painting the exposed portion or loop,all as per standard design complete including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 85 (eighty five ) centimetre height railing with MS rectangular hollow pipe 75x50 (seventy five into fifty) millimetre of 14 (Fourteen) gauge M.S. black sheet make hand rail and M.S Square bars 20 (twenty millimetre) size balusters at 30 cm (thirty centimetre) Centre to centre duly welded with 2 Nos (Two Numbers) MS flat 40x6 mm (Forty into six millimetre) size and 20 (Twenty millimetre) M.S square bars lugs 10 (Ten centimetre) Long at lower end of balusters embedded in RCC steps or waist slab including prime coat of steel primer and painting with steel enamel paint other than white as per design and instruction of Engineer -In Charge. , including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming paint brushing red lead, red oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters with ready mixed paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint brushing wood primer pink as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping with ready mixed paint other than white or as per direction of Engineer-in- Charge including carriage of materials within all leads, lifts and other incidentals.

6mm (Six milimetre) thick cement plaster to ceiling with cement mortar 1:4 (one cement :four sand) including carriage of materials within all leads, lifts and other incidentals.

15 mm (Fifteen milimetre)Cement plaster in single coat on rough side of brick /concrete stone wall for interior plastering upto floor all level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre)in girth and finished even and smooth in Cement Mortar 1:6 (One Cement :Six sand) above plinth level upto floor any level as per direction of Engineer-in- Charges within all leads, lifts and other incidentals

15 mm (Fifteen millimetre)Cement plaster in single coat on fair side of brick /concrete stone walls for interior plastering upto floor all level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre)in girth and finished even and smooth in Cement Mortar 1:6 (One Cement :Six sand) above plinth level upto floor any level as per direction of Engineer-in- Charges within all leads, lifts and other incidentals..

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth on walls priming coat with distemper primer as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

White washing with lime on ceiling and /or sloping roof (Two coats) to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter including carriage of materialswith in all leads, lifts and other incidentals..

Providing plinth protection 50 (fifty) millimetre thick in cement concrete 1:3:6 (One Cement : Three Sand : Six Graded stone aggregated 20 (Twenty ) millimetre nominal size) including carriage of materials upto all leads , lifts and and other incidentals.

Provding under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed of dry brick/stone aggregate 40mm (forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparetion of ground including carriage of materials with in all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Constructing course rubble hammer dressed "U" shape open surface drain with side wall 15X22 (Fifteen into Twenty Two) cm in cement mortor 1:6 (one cement: six sand) and in side plstring with cement mortar 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (Seven point Five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors 15mm (Fifteen Millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and laying in trenches, galvanised mild steel tubes ( medium grade), tube fittings (earth work in trenches to be measured and paid separately) 15mm (Fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 500 litres(five hundred litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing sand cast iron/cast iron spun spigot and socket soil waste and ventilating pipe(Lead caulked joints to be measured and paid for separately. 100 mm (One Hundred millimetre) nominal size including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing sand cast iron/cast iron spun fittings and accessories coller 100mm (One Hundred millimetre) nominal size inclduing carriage of matrials within all lads, lifts and other incidentials

Providing and fixing Lead caulked joints to sand cast iron cast of (sun) iron pipes supn fittings including testing of joints 100 millimetre nominal size diameter inclduing carriage of matrials within all lads, lifts and other incidentials

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting and making goods the walls and floors100 millimetre nominal diametre including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings Vitreous China 600 (six hundred) millimetre x 450 (four hundred fifty) millimetre x 150 (one hundred fifty) millimetre inclduing carriage of matrials within all lads, lifts and other incidentials.

Providing and fixing C.P. Brass chain 50 (fifty) centimetre long and rubber plug of following sizes for sink or wash basin 32 (thirty two) millimetre dia inclduing carriage of matrials within all lads, lifts and other incidentials.

Providing and fixing C.P. Brass waste for wash basin or sink 32 mm (thirty two millimetre) dia inclduing carriage of matrials within all lads, lifts and other incidentials.

Providing and fixing M.I. Union for wash basin or sink 32 mm (thirty two millimetre) dia inclduing carriage of matrials within all lads and lifts and other incidentials.

Providing and fixing C.P. brass pillar tap with capstan head 15mm (fifteen millimetre) dia as per direction of Engineer-in- Charges within all leads,lifts and other incidentials.

Providing and fixing C.P. brass angle valve 15 (fifteen millimetre) without Nuts and pipe inclduing carriage of matrials within all lads and lifts and other incidentials.

Providing and fixing PVC connections with brass unions:- 450 mm (four hundred fifty millimetre) length as per direction of Engineer-in- Charge within all leads , lifts and other incidentials.

Providing and fixing brass full way valve with wheel 15 mm (fifteen millimetre) nominal size bore as per direction of Engineer-in- Charge within all leads, lifts and other incidentials.

Providing and fixing P.V.C waste pipe flexible ( Coil type) length not less then 800 mm (eight hundred millimetre) for wash basin inclduing carriage of matrials within all leads, lifts and other incidentials.

SOM KRISHAN GOVT CONTRACTOR