Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹75.8 CrAccepted-Finance 110 NETAJI SUBHASH PLACE PITAMPURA NEW DELHI 110034 | NORTH WEST DELHI | DELHI | 110034 | ₹75.8 Cr | L1 | Accepted-Finance Bidder is L-1 |
| 2 | L2₹79.5 CrRejected-Finance B 22 2ND FLOOR HIMALAYA HOUSE 23 K G MARG CANNAUGHT PLACE NEW DELHI 110 001 | NEW DELHI | DELHI | 110001 | ₹79.5 Cr | L2 | Rejected-Finance Bidder is not L-1 |
| 3 | L3₹87.8 CrRejected-Finance | ₹87.8 Cr | L3 | Rejected-Finance Bidder is not L-1 |
| 4 | L4₹88.0 CrRejected-Finance D 1 1 GILLANDER HOUSE 8 N S ROAD KOLKATA 700 001 | KOLKATA | WEST BENGAL | 700001 | ₹88.0 Cr | L4 | Rejected-Finance Bidder is not L-1 |
| 5 | Rejected-Technical | - | - | Rejected-Technical Not eligible for opening of financial bid |
Tender Value
₹88.8 Cr
EMD Value
₹25 L
Closing Date
26 May 2020, 11:00 amClosed
General Manager/CP
2nd Floor, RITES Bhawan-II, Plot No. 144, Sector-44, Gurgaon- 122003
Construction and Development works of RITES Office Building at New Town, Rajarhat, Kolkata
2020_RITES_42551_1
RITES/CP/TC/ROC-KOLKATA/20
Open Tender
Civil Works - Buildings
840 days
New Town, Rajarhat, Kolkata
Please refer Tender Documents
10 documents required · 10 mandatory
₹18,000
Yes
RITES Ltd.
₹25 L
Yes
Gurgaon
20 Oct 2020
10 Feb 2020
27 May 2020
10 Feb 2020
26 May 2020
28 Feb 2020
11 Feb 2020 - 24 Feb 2020
24 Feb 2020
Amount
Total Amount of BoQ 2
Amount after unconditional Rebate
Description of Work / Item(s)
Amount
Total of BoQ 3, BoQ 4, BoQ 5 and BoQ 6
Total Amount of BoQ3 (Item Rate)
Total Amount of BoQ4 (Percentage Rate)
Total Amount of BoQ5 (Percentage Rate)
Total Amount of BoQ6 (Percentage Rate)
Description of Work / Item(s)
Amount
Schedule - (E) Bill of Quantites for Non Schedule Items (MR ITEMS)
NS1- Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used.
NS 1.1- 800 mm dia piles
NS 2- Boring charges only for piling work from existing GL (+) 0.00M to Level (-) 7.450M
NS 2.1- 600 mm dia piles
NS 2.2- 750 mm dia piles
NS 2.3- 800 mm dia piles
NS 3- Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note:2: Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge.
NS 3.1- Initial test (Test Load 2.5 times the Safe Load capacity)
NS 3.1.1-Single pile above 250 tonne and upto 300 tonne capacity (As per Design required 1110 KN)
NS 3.1.2-Single pile above 300 tonne and upto 350 tonne capacity (As per Design required 1400 KN)
NS 3.1.3- Single pile above 450 tonne and upto 500 tonne capacity (As per Design required)
NS 3.1.4- Single pile above 500 tonne and upto 550 tonne capacity (As per Design required)
NS 3.2- Cyclic vertical load testing of pile in accordance with IS Code of practice IS: 2911 (part IV) by Kentledge method including preparation of pile head etc for single pile
NS 3.2.1-Single pile above 150 tonne and upto 200 tonne capacity (As per Design required for 600 mm dia.)
NS 3.2.2- Single pile above 200 tonne and upto 250 tonne capacity (As per Design required for 600 mm dia.)
NS 3.2.3- Single pile above 250 tonne and upto 300 tonne capacity (As per Design required for 750 mm dia.)
NS 3.2.4- Single pile above 300 tonne and upto 350 tonne capacity (As per Design required for 800 mm dia.)
NS 4- Shoring work with ISMB 500 spaced at 600 mm c/c with horizontal bracing and diagonal bracing at four corners of ISMB 300 driven into the soil length 17M with in fill 12 mm M.S plate wall plate(upto 8m depth) between the two ISMBs complete in all respect including extraction. Shoring design to be approved by Engineer in Charge.
WATERPROOFING TREATMENT FOR RAFT (using 1.2 mm thick HDPE Membrane)
NS 5- Supplying and installation of 1.2 mm thick HDPE Membrane and unique pressure sensitive adhesive based Master Seal 730 PA or equivalent over top of finished PCC, for Raft Waterproofing work. The protection layer of waterproof membrane system, followed by a cement mortar screed of 50 mm thick over the HDPE. The protection mortar screed is provided to facilitate the placing and tying of reinforcement bars of raft. (Cost of Concrete for screed to be paid separately)
PILE HEAD TREATMENT (Upto Dia. 1200 mm, 50 mm upstand)
NS 6- Providing & dressing 1.2 mm thick HDPE Waterproofing Membrane around the periphery of pile heads upto the cover zone and encapsulating the waterproofing membrane by adhening it with stiky tape. Then cover the pile top surface by microconcrete MasterEmaco S340 or equivelent.
WATERPROOFING TREATMENT OF RETAINING WALL FOR UNCONFINED AREAS (using 2 mm thick spray applied 2-component solvent free fast setting polyurathene WP System)
NS 7-a) Surface preparation : Cleaning the surface of the slab/ Raft, making it absolutely free from dust, oil or any type of deleterious materials etc. and chipping off the loosely adhered mortar. The cleaning and preparation of the RCC surface must be carried out thoroughly to leave a sound base for the application. Release oil and other contaminants which may impair adhesion must be removed prior to the primer use of surface grinder is must.
b) Supply and installation of spray applied PU material : Waterproofing membrane system a multi-layered system comprising of a series of substrate sealers, primers, waterproofing membranes spray applied membrane system for retaining wall that, system shall be not left exposed, to be filled.
c) Waterproofing System - PU system : A liquid applied, crack bridging covered waterproofing system based on advanced polyurethane material. It consists of a primer and a spray applied elastomeric polyurethane waterproofing membrane . Then applying solvent free (100% solid content) two component Polyurethane spray applied waterproofing system Master Seal M800 or equivalent to be laid directly above primed RCC surface in horizontal and vertical face covering every possible area at 1.5 mm average thickness with 1.6 kg/ Sqm consumption, using 2 component spray machine as per approved manufacturers specifications and green certified . Then covered by Geotextile membrane of required thickness gsm geotextile on water proofed surface as per Manufacturer's specification (BASF or equivalent). Finaly the protection layer of waterproof membrane system, followed by a Styroboard (25 mm thickness, 10 kg/m3).
NS 8- Providing and laying Antiskid Vitrified floor tiles in sizes (600 x 600) mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.
NS 9- Design, Manufacture, supply and installation of Façade (dpi system or equivalent), a complete assembly of co-extruded UV protected 18 mm thick multi-layered polycarbonate (approved colour and make dpi daylighting or any equivalent) panels with angular walls incorporated into a complete system in building Façade. Panels shall have 7 layers with angular walls with opaque and translucent clear blinds in combination as per required Lux Level inside the building. Panels shall be with grip-lock notch standing seam running lengthwise to accommodate the connectors. Panel system shall be assembled & installed on Aluminium Malian Structure (Paid separately) at center to center 1202 mm with self-drilling screws in a continuous aluminium connector with gripping the panel width on both sides. (a)The system shall ensure the mechanical strength, water tightness and air tightness of the roof as per Panel length of 11980 mm (Max.) and width of 1200 mm. (b) Aluminium connector assembly shall have a pull-out load of 2.1 KPA (min) when tested as per ISO 6892 : 1998 and IS 1608:2005. (c) Panels shall pass dart drop impact test as per IS 14443-97, shall show no sign of breakage on Polycarbinate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. (d) Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. (e) Panel shall be with additional End cap/Aluminium U / F Profile / Glazing Bar (mill finiish) for ends as required. (f) Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineer in charge.
NS 9.1- Providing and fixing aluminium frame work for Aluminium Malian Structure to assemble the 18 mm thick Polycarbonate panel system.
NS 10-"Providing and fixing Automatic Sliding door operator, Make: DORMA ES 200 STD 4150 or equivalent make Hafele etc. compliant with future European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and the VDE regulations. TÜV design tested, tested according to the low voltage guidelines, production according to ISO 9001:2000 certification, fulfils DIN18650, TUV Design Tested for Durability of 1 Million Cycles, for frameless glass door application, with 12 mm clear toughened glass for 2 Nos sliding door panels and 2 Nos fixed panels, Operator mounted on wall, Operator Finish should be Silver Anodised E6/C0, with operator dimensions (H x D) : 100 x 180 mm and of length as required to suit the opening size given below, Operator to be of modular design including internal cover. The track profile should be separate from the main profile for enabling reduction in vibration insulation. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Class of protection IP 20. Activators- DORMA Eagle 6 Safe Combination Radar system or equivalent with Motion & Presence (02 Nos) with 24 GHz, Mandatory as Int’Nat Standards, Light barriers, comprising receiver and transmitter - 02 Pair with Electro-Mechanical locking and 5 Position Program Switch with Key and designed for a Maximum Panel Weight Carrying Capacity of 2 X 160 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC . The requirement in total is as mentioned below:" Glass Clamping Rail - 1550 mm - 2 Nos,Floor Guide for Glass Door - 2 Nos,Radar Eagle STD 6 - 2 Nos. - Silver,Light Barrier SBK 111 - 1 Pair,Five Position Program Switch with knob,Cable For Program Switch
NS 10.1- Special Manet Fixed -for 12 mm Glass over panel fixing
NS 10.2- Special Manet Flexible - for 12 mm Glass over panel fixing
NS 11- Front glass façade : Design, supplying & fixing of frameless glazed façade as per IS 875 part 3 and AS1288 2006 CODAL requirements, suspended from the top of the opening incorporating 12 mm thick toughened glass panels as per approved drawings and toughened/ laminated glass fins as stabilizers, used at each vertical joint to provide lateral stiffness against wind loading. Deflections and other specified loads expected including frame work wherever necessary and hardware all other accessories in the glazing with all extrusions, fittings, suspension brackets, spider fittings of DORMa make with 4, 2 points spiders & RODAN stainless steel bolts as per design. The DORMA spider fin fitting shall have a stream line design with twirl arm for high strength performance and better aesthetics, the RODAN bolts for facade glass shall be of SS 316 with all necessary accessories. the spiders shall be manufactured by investment casting process of grade SS 316 as per EN norms. All screws, all weather elements such as flashing, coping. approved silicone sealants, etc to make the system completely waterproof. All spider fittings should be designed to support the weight of the glass by direct bearing on the bolts wherein the structure should be designed as per the relevant codes and should be able to withstand the relevant thermal movements. Design calculations for the facade to be furnished for approval by client / consultant.
NS 12- Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
With 6 mm thick toughened glass for door shutter
NS 13- Providing and fixing PVC sheet flooring of thickness of 2 mm with HOF-TORO SC/TARKETT the size of 2m x 20m . The product should be homogeneous and single layered with PUR (Clean Sweep)range. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC with TRUESHIELD technology, Plasticizers without DOP, Urethane, color pigments and filler calendared to form a sheet. Color and pattern details shall be dispersed throughout the thickness of the wear layer. It should conform to group "T" wear resistance as per EN 685, Flammability resistance of class Bfl-s1 as per GB8624-2006, Dynamic coefficient of friction of class DS as per EN 13893, Thermal Resistance of 0.072m2K/W as per EN 12667, Thermal conductivity of 0.071W/mK as per EN12524, impact sound reduction of 3dB as per ISO 10140, Slip Resistance of class R9 as per DIN 51130, Residual indentation of 0.03mm as per GB/T 4085-2005, Color fastness rating of ≥6 as per ISO 105-B02, total weight being 3.3kg/m2 as per EN430. The product shall be suitable for applications in class 23/34/43 areas as per EN685. Product shall exhibit antistatic behavior, resistance to bacteria, resistance to chemical, resistance to staining, suitability to castor chair. The product shall be Floor Score certified with no SVHC content published by European Chemicals Agency (REACH). Product shall contribute to LEED points under Indoor environmental quality category. Equivalent to Armstrong Medintech Plus.
NS 13.01- Extra for joining of PVC sheets by Hot Welding Chord.
Water Proofing Treatment for Toilet Floor
NS 14.1- Cleaning of RCC to remove dust and loosely adhering particles completely.
NS 14.2- Supply and application of 1:3 cement – sand mortar, mixed with SikaTop 77 / or equivalent other company, the polymer modified high quality emulsion, as a coving at the corners of floor and the vertical surface in the sunken area, and between floor and walls in the remaining area.
NS 14.3- Supply and application of SikaTop Seal 107 or equivalent other company– the cementitious, flexible waterproof coating on to the prepared surface in a continuous film on the floor of the sunken area, taking the coating over the vertical surfaces on to the floor and over the coving on to the wall (before tiling) to at least 300mm above the final finished floor level. The coating shall also be continued on to the inner surfaces of the pipe penetration holes. Two coats shall be applied.
NS 14.4- Providing a 15mm thick plaster on the waterproof coating by mixing an integral waterproofing compound, Plastocrete Plus or approved equivalent @ 100gms per bag of cement.
NS 14.5- Providing Sikagard 694F(I), a moisture insensitive epoxy putty or approved equivalent, in a continuous, 10mm thick gasket around the pipes to a width of approximately 15mm.
Water proofing Treatment at Roof surface.
NS 15.1- Labour for cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air, including all materials, labour, tools and tackles complete Repairing surface irregularities, damaged concrete in base slab, if any, with a styrene butadiene polymer, Sika Latex or equivalent modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools and tackles complete.
NS 15.2- Providing and applying 2 coats of Sikatop seal 109hi - 2 or approved equivalent, component polymer modified coating after application of Sikatop seal 109hi primer over the roof after proper surface preparation.A glass fibre cloth shall be put in between two coats including labour tools and tackles etc all complete.
NS 15.3- Supply and application of 1:3 cement-sand mortar, mixed with Sika-Top 77 or approved equivalent the polymer modified high quality emultion, as a coving the corners of floors and the vertical surface in the sunken area, and between floor and walls in the remaining area.
NS 15.4- Providing rounding finished with screed concrete at adjacent corners of terrace & Parapet wall (100 mm radius).
Water proofing Treatment at Roof Garden Surface
NS 16- (a) Surface preparation : Cleaning the surface of the slab making it absolutely free from dust, oil or any type of deleterious materials etc. and chipping off the loosely adhered mortar. The cleaning and preparation of the RCC surface must be carried out thoroughly to leave a sound base for the application. Release oil and other contaminants which may impair adhesion must be removed prior to the primer use of surface grinder is must. (b) Supply and installation of spray applied PU material for Primer coats : Waterproofing membrane system a multi-layered system comprising of a series of substrate sealers, primers, waterproofing membranes. Spray applied membrane system for flat roofs that have built ups or landscape above the waterproofing coat system not left exposed. (c) Waterproofing Membrane : Providing & applying solvent free (100% solid content) two component Polyurethane spray ( Master Seal M800 or equivalent ) applied waterproofing system to be laid directly above primed RCC surface in horizontal and vertical face covering every possible area at 2 mm average thickness using specialized 2 component spray machine as per approved manufacturers specifications and green certified. (d) Geotextile Membrane : Providing & laying fixing of required thickness gsm geo textile on water proofed surface as per Manufacturer's specification (BASF or equivalent). (e) Slope / Protection Screed : Laying M25 grade screed concrete with PC based admixture mixed with waterproofing admixture MasterPel 777 or equivalent. (Surface absorption of water, BS 1881 - Part 122, 50% lower than control) @ 250 ml/ bag of cement (as per Manufacturer's specification) of the cement as a protecting cover with minimum thickness of 50 mm as per slope (as per drainage design drawing ) as per site requirement including cutting grooves for control joints as directed by EIC. The covering concrete has to be done in alternate panels as directed by EIC, all joints have to be (as per manufacturer's specification ) filled with appropriate chemical materials.
Expansion joints Treatment
NS 17- Supply and apply a polysulphide based elastic, sealant. Including complete installation as per manufacturer’s method statement including cleaning of the joint, repair of the joint edges (if required), backer rod, primer, finishing etc.
Water Proofing Treatment for Overhead Tank
Floor Slab
NS 18.1- Cleaning of RCC to remove dust and loosely adhering particles completely.
NS 18.2- Supply and application of an acrylic coating [ShaliCem FWP or equivalent : IS 6582 (compatibility with drinking water) and ASTM 2370 ] on the prepared substrate, after making the surface in SSD condition.
NS 18.3- Providing a 25 mm thick screed should be prepared by mixing an integral waterproofing compound, ShaliPlast LW+ or equivalent @ 100gms per bag of cement
NS 18.4- Supply and application of an expanding grout admixture ShaliGrout IP or equivalent for pressure grouting using min. 15mm dia, 100mm long GI nozzles 1.5 m C/C in the concrete with the help of 200mm long dummy rod. Dummy rod should be removed after the initial set of concrete. Extra nozzles are to be provided along the construction joint.
Retaining Wall
NS 18.5- Cleaning of RCC to remove dust and loosely adhering particles completely.
NS 18.6- Supply and application of an acrylic coating [ShaliCem FWP or equivalent: IS 6582 (compatibility with drinking water) and ASTM 2370 ] on the prepared substrate, after making the surface in SSD condition.
NS 18.7- Providing a 12 mm thick protective plaster on the waterproof coating by mixing an integral waterproofing compound, ShaliPlast LW+ or equivalent @ 100gms per bag of cement.
NS 18.8- Supply and application of an expanding grout admixture for pressure grouting using G.I nozzles and by fixing the nozzles 1.5m c/c.
Water proofing Treatment For U/G Tank.
NS 19.1- Providing and fixing of 100mm long, 15 NB galvanized MS threaded nozzles With quick setting compound in gridpattern (the spacing of nozzles should not be more than1.5m centre to centre), while concreting in RCC wall/Raft and injecting/ grouting of cement slurry admixed with Sika Intraplast EP or equivalent non-shrink grout by hand operated grouting pump under maximum pressure of 2.5Kg/Cm2 .
NS 19.2- Grouting of cement slurry admixed with Sika Intraplast EP or equivalent non-shrink grout by hand operated grouting pump under maximumpressure of 2.5Kg/Cm2 .
NS 19.3- Raft : Cleaning PCC surface, smoothening with sand mortar and applying two coats of Sikatop seal 107 or equivalent polymer modified cementitious slurry coating over lean concrete surface. Providing and laying 12 mm cement sand plaster(1:4) over the acrylic polymer modified coating.
NS 19.4- Retaining wall : Applying two coats of Sikatop seal107 or equivalent acrylic polymer modified cementitious slurry coating over outer surface of RCC walls. Providing and laying 12mm cement sand plaster 1:4 as protection layer all complete.
MS Puddle Piece
NS 20.1-Providing and fixing 300 mm dia , 900 mm long of 6.4 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 450x450x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 25 mm (500 mm dia.) with 12 nos hole for Bolt (M20) .
NS 20.2- Providing and fixing 250 mm dia , 700 mm long of 6 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 400x400x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 25 mm (440 mm dia.) with 12 nos hole for Bolt (M20) .
NS 20.3-Providing and fixing 200 mm dia , 700 mm long of 6 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 350x350x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 25 mm (370 mm dia.) with 12 nos hole for Bolt (M20) .
NS 20.4-Providing and fixing 150 mm dia , 700 mm long of 5.4 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 300x300x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 25 mm (300 mm dia.) with 12 nos hole for Bolt (M20) .
NS 20.5-Providing and fixing 100 mm dia , 700 mm long of 5.4 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 200x200x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 20 mm (225 mm dia.) with 8 nos hole for Bolt (M16) .
NS 20.6- Providing and fixing 80 mm dia , 700 mm long of 4.85 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 200x200x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 15 mm (200 mm dia.) with 8 nos hole for Bolt (M16) .
NS 20.7-Providing and fixing 65 mm dia , 700 mm long of 4.05 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 15 mm (185 mm dia.) with 4 nos hole for Bolt (M16) .
NS 20.8- Providing and fixing 50 mm dia , 700 mm long of 4.05 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 15 mm (165 mm dia.) with 4 nos hole for Bolt (M16) .
NS 20.9-Providing and fixing 25 mm dia , 700 mm long of 4.05 mm thick puddle piece with IS:3589 (M.S. ERW) pipe during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 6 mm at middle of Puddle Pipe and M.S. Flange thick of 15 mm (165 mm dia.) with 4 nos hole for Bolt (M16) .
GI Puddle Piece
NS 20.10-Providing and fixing 80 mm dia , 900 mm long of puddle piece with GI pipe (heavey duty /Class C) during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 200x200x 3 mm at middle of Puddle Pipe and GI Flange thick of 10 mm (200 mm dia.) with 8 nos hole for Bolt (M16) .
NS 20.11- Providing and fixing 65 mm dia , 900 mm long of puddle piece with G.I. pipe (heavey duty /Class C) during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 3 mm at middle of Puddle Pipe and G.I. Flange thick of 10 mm (185 mm dia.) with 4 nos hole for Bolt (M16) .
NS 20.12- Providing and fixing 50 mm dia , 900 mm long of puddle piece with G. I. pipe (heavey duty /Class C) during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 3 mm at middle of Puddle Pipe and G.I. Flange thick of 10 mm (165 mm dia.) with 4 nos hole for Bolt (M16) .
NS 20.13-Providing and fixing 25 mm dia , 900 mm long of puddle piece with G. I. pipe (heavey duty /Class C) during casting of concrete shall be a coat of synthetic oil bound Primer and remaining surface of pipe (inside & outside) shall be painted with two coats of Synthetic Enamel paint. Including welding the Puddle Plate size of 150x150x 3 mm at middle of Puddle Pipe and G.I. Flange thick of 10 mm (165 mm dia.) with 4 nos hole for Bolt (M16) .
NS 21-Supplying, fitting and fixing in position true to line and level elastomeric bearing conforming to IRC:83 (Part-II) section IX and clause 2005 of MoRTH specification complete including all accessories as per drawing and technical specification.
NS 22-Supplying & providing for terrace gardening at all level with artificial grass 40 mm completed as per direction of EIC.
NS 23-Supply and fixing of troughed SMARTDEK 51 ( or equivalent )structural metal decking sheet for floor shall be 960 mm effective cover width with 51 mm deep ribs with pitch of 320 mm centre-to-centre, with embossment on ribs with stiffener in rib and pan for mechanical connection between the steel and concrete, with male and female side lap joint manufactured out of feed material of thickness of 1.20 mm ( BMT) ,galvanised to grade 275 (minimum) as per IS : 277 of minimum yield strength of 550 MPa of drawing grade as per IS : 513 and of approved profile, sectional properties (suitable for the specified loading / deflection and purlins / runner spacing.
NS 24-80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern for provition of Grass growth into the holes.
NS 25- Supplying and fixing 560 mm dia C.I. cover with frame (heavy duty) for manholes. [ the weight of the cover to be not less than 108 kg ]
NS 26-Providing and fixing Brass Sliding Door bolts, ISI marked, transparent or dyed to required colour or shade, with nuts and screws etc. complete :
NS 26.1-300 x16 mm
NS 26.2- 250 x16 mm
NS 27-Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 450 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.
SHRUBS
NS 28.1-Supplying and planting of Raphis palm plant, having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves as per direction of the engineer-in-charge.
NS 28.2- Supply and planting of plant Cassia biflora of height 45-60 cm. as per direction of the engineer-in-charge.
NS 28.3-Supply and planting of plant Excoecaria bicolor of height 45-60 cm. as per direction of the engineer-in-charge.
NS 28.4-Supply and planting of plant Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage as per direction of the engineer-in-charge.
NS 28.5-Supply and planting of plant Hibiscus rosasinensis of height 60-75 cm. with 5-6 branches as per direction of the engineer-in-charge.
PALMS & TREES
NS 29.1-Supply and planting of Plumeria alba plant of height 120-135 cm. with 2-3 branches as per direction of the engineer-in-charge.
NS 29.2-Supply and planting of Polyalthia longifolia (Ashok) plant of height 150-165 cm. as per direction of the engineer-in-charge.
NS 29.3- Supply and planting of Delonix regia (Gulmohar) plant of height 150-165 cm. as per direction of the engineer-in-charge.
NS 29.4- Supply and planting of plant Caesalpinia pulcherrima species of height 45-60 cm. as per direction of the engineer-in-charge.
NS 30-Supply and fixing Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm, PVC coated to outer dia 5 mm
NS 31-Supplying, fitting and fixing in position for Sliding Gate Wheel (75 mm dia.) with all accessories
FIRE PROOF STEEL DOOR
NS 32.1- (a) Providing and fixing of Metal Fire door from ISO 9001:2015 certified Manufacturer . The door must have been manufactured with galvanised - GI sheet of GPSP Grade as per IS 277. All Fire doors must satisfy the requirement of latest NBC 2016 Part 4 for Fire & Life Safety guidelines for 120 minutes Fire Rating with minimum 20 minutes Insulation properties along with its Stability & Integrity for 120 minutes. The Prototype sample of the door must carry a prior test evidence as per IS 3614 part-2 / BS 476 Part 20 & 22 . The manufacturer must submit the copy of test evidence prior to start of production .The offered test certificate should either carries it's Validity or certificate must not be older than 5 years from CBRI / NABL Accreditated Lab i.e Spectro / International Lab i.e Exova / TBW etc . Recommended fire door must also be certified by a third party evaluation program from approved International agency like IFC/ Intertek/ Certifire and must carry a lable on all doors . All doors should be finished with Powder coating in desired regular RAL Shades. (b) Door frame shall be Single rebate profile of section 100 x 57 mm made out of 1.20mm thick galvanised steel sheet with a factory pre-punched groove so as to accomodate Fire & smoke seal size 10x4mm . Frames should be butt jointed and field assembled with bolting system for proper strength .Frames should be provided with back plate for anchor fasteners (payable extra ) for installation on a finished plastered wall opening. (c) Door leaf should be minimum 46mm thick fully flush double skin door. Door leaf must be manufactured from 0.8mm (22 guage) thick galvanised steel sheet. The door should be provided with reinforcement pads to receiving appropriate Hardwares of Becker Fire Solutions or Equivalent make. The Shutter shall be filled with proprietary infill material . For Double leaf doors; astragal has to be provided on meeting stile for both active and inactive leaf. Vision panels wherever required should be of 120 minutes fire rating and should be of non-wired type. All hardwares , Fasteners and FR Glass shall be payable separately.
NS 32.2- Supply & fixing of SS Ball Bearing Hinges of size 100 x 75 x 3mm complet with SS Screws of BB1953 Becker F.S / DORMA / Geze Make ( 4 Nos per panel ) (Required For All Doors)
NS 32.3-Supply & fixing of anchor fastners of HILTI/ FISHER/ Equvalent of maximum 80mm length.(Required For All Doors)
NS 32.4- Supply & fixing of door closers of BLC-0408 Becker F.S/ TS-68 DORMA / Geze Make. (Required For All Fire Doors)
NS 32.5- Supply & fixing of Mortise Dead Lock Becker F.S. / 917 DORMA / Geze Make.
NS 32.6- Supply & fixing of SS D Type Offset Pull Handle of size 300mm mm Long of PHD2230 Becker F.S/ Geze/ TGDI30022 DORMA Make.
NS 32.7- Supply & fixing of Mortise Shash Lock With SS Lever Handle Of SL7260/ TLH612 Becker F.S. / DORMA 281 / 8014001/ 8245/ Geze Make
NS 32.8- Supply & fixing of Stainless Steel 304 grade 300mm Long Concealed Flush Bolt of BFBS1930 Becker FS/ 9114306 DORMA/ Geze Make with necessary screws as required. (Required with all varieties of Double Leaf door except having 3 Point Panic Bar)
NS 32.9- Supply & fixing of shaft lock with allen key of Becker FS/ 9119315 DORMA/ Hafele Make.
NS 32.10- Supply & fixing of SS flush pull handle of BFPR1250 Becker FS/ Geze/ 9112177 DORMA Make.
NS 32.11- 5 MM thick clear Non wire 2 Hr Fire Vision glass 300x300mm Saint gobain make
NS 32.12- Supply & fixing of SBL 990/995 Becker F.S. / PHCR 1000 Series DORMA / GEZE Make Panic Bar single / double leaf panic exit devices. Double Leaf Panic Bar Set
NS 33- Providing and laying Tac Liner tiles in Floor sizes (300 x 300) mm and 15mm thickness with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.
Core Cutting in RCC Slab & Wall
NS 34.1- Core Cutting- 127mm dia,0-200mm depth of hole
NS 34.2- Core Cutting- 152mm dia,0-200mm depth of hole
NS 34.3- Core Cutting- 202mm dia,0-200mm depth of hole
Rebar Grouting (10 D) in Concrete
NS 35.1-8 mm dia bar
NS 35.2- 10 mm dia bar
NS 35.3- 12mm dia bar
NS 35.4- 16mm dia bar
NS 35.5- 20 mm dia bar
NS 35.6-25mm dia bar
NS 36-Supplying,fixing and installation of Premium LED Signages of Acrylic sheets with low volt LED fitting inside the lerrers and fixed on SS screws over 4mm thick ACP sheet background including structures of size not less than((3m L x 0.9m H) all as per drawings and instruction of Engineer-In-Charge.
NS 37-Supplying,fixing and installation of LED Backlit Acrylic sheet raised segnages on 4mm thick ACP sheet background with Aluminium framework complete as per drawing and instruction of Engineer-In-Charge.9Size not less than 2.5m L x 0.75m)
NS 38-Supplying,fixing and installation of Directional Signages Acrylic/metallic make retro-reflectorized all as per drawings(size not less than 300mmx200mm)
NS 39-Design, Supply, Fabrication and erection of suitable Mild Steel Canopy structures followed by 1 coat of Epoxy primer and two coats of PU paint (As per approved colour) and other hardware & accessories along with supply & installation of 17.52 mm thk. clear/Frosted laminated glass using SS- Spider (DORMA) , SS- STUD, NUT , silicon sealant and other necessary hardware & accessories wherever applicable.
NS 40.1-Supplying & fixing of Fabric made Venitian Blinds
NS 40.2- Supplying & fixing of Fabric made Roller Blinds
NS 40.3- Supplying & fixing of Wall Graphic of Vinyl Films with design printing as per drawing.
NS 40.4- Supplying & fixing of good quality Wall Paper as per design and drawing.
NS 41-Supplying and filling sand under floors, including watering, ramming, consolidating and dressing complete above plinth level upto 12th floor level.
INTERNAL WATER SUPPLY AND SANITARY WORKS
NS 42- Supplying, fitting and fixing of Wall Hung white glazed vitreous chinawar E.W.C.including Dual Flush cistern and white plastic seat cover of approved make complete in position with necessary bolts, nuts etc. (a) EWC size :535x360x335,Cat no-S1041108,P Trap Cat no-B1520112,Croft Closed Seat Cover(CERA) or Parryware,Cat no-C0211 Closet. (b) Vitreous china Concealed low level cistern (Dual Flush & 6/3 litres per flush) ,size-495x80x410,cat no-B1110103 with knob cat no-B1120105, Cistern set (CERA) with fittings or Parryware,Cat no-E812599 &E8220A1.
NS 43- Providing and fixing Table top wash basin including 15 mm dia CP Brass pillar cock with aerator of approved quality and make, and 32mm dia CP waste pipe including painting of fittings, cutting and making good the walls wherever required: (a) White Vitreous China Wash basin size -600x435 mm cat no-S2020115 with a 15 mm CP Brass pillar cock cat no-F1014101(cera) or Parryware Cat no-C8909 & T4665A1.
NS 44- Providing and fixing Counter Wash Basin including 15 mm dia CP Brass pillar cock with aerator of approved quality and make, and 32mm dia CP waste pipe including painting of fittings, cutting and making good the walls wherever required: (a) White Vitreous China Wash basin size -560x470 mm cat no-S2030118 with a 15 mm CP Brass pillar cock cat no-F1014101(cera) or Parryware Cat no-C0447 & T4665A1
NS 45- Supplying, fitting and fixing in position CP single flow over head shower 85mm dia ( with arm and wall flange) of approved make.cat no-F7020102(cera) or Parryware,Cat no-T9927A1
NS 46- Supplying, fitting and fixing in position CP Bib Cock-15mm bore(3.8L/Min) with Aerator and Wall Flange of approved make.cat no-F1012151(cera) or Parryware,Cat no-T3904A1
NS 47- Supplying, fitting and fixing in position CP brass two way Bib Cock-15mm bore with wall flange and Aerator of approved make.cat no-F1012163(cera) or Parryware,Cat no-G1867A1
NS 48- Supplying, fitting and fixing CP Towel Rail,600mm long.cat no-F5004103(cera) or Parryware,Cat no-T6401A1
NS 49-Supplying, fitting and fixing 15 mm CP pillar cock(2.5L/Min) with Aerator of approved make. cat no-F1014101(cera) or Parryware,Cat no-T4665A1
NS 50-Providing and fixing vitreous china Laboratory Sink,size-600x400x200,cat no-S6010102(cera) or equivalent.
NS 51-Supply fitting and fixing White Urinal of Size-320x300x525mm with intregrated Electronic Flushing Systems and AC/DC power source. cat no-S4010102(cera) or Parryware,Cat no-C0587
NS 52- Supply fitting and fixing White Urinal of Size-420x395x635mm. cat no-S4020102(cera)p/51 or Parryware,Cat no-C0580
NS 53- Providing & fixing Hot Water GEYSER of Approved Make-Cera including with 2nos connection pipe 450mm long.cat no-F8070403(cera) or equivalent as per instruction of Engg-In-Charge.
NS 53.1- 10 Ltrs. capacity - ceracat no-H1010001 or equivalent.
NS 53.2-25 Ltrs. capacity -cera cat no-H1025001 or equivalent
NS 54- Supplying, fitting and fixing in position Health Faucet POM with 1.2 metre braided hose pipe of approved make,cat no-F8030401AB(cera) or Parryware Cat no-T9941A1
NS 55- Supplying,fitting & fixing CP Soap Dish.cat no-F5003106(cera) or Parryware,Cat no-T6003A1
NS 56- Supplying, fitting and fixing Aluminium domical grating. 100 mm
NS 57- Supplying, fitting and fixing of C I Nahani Trap including all complete. Size-100x75
NS 58- Supplying,fitting,fixing self contained water cooler of storage capacity 80 litre and normal cooling capacity 60 lt/hr. with 2nos of faucets with RECIP compressor.
NS 59-Supplying fitting & Commissioning of Water Metre including all complete.
NS 59.1- 32mm bore
NS 59.2- 25mm bore
NS 60- Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
NS 60.1- 65 mm dia nominal bore (heavy grade)
NS 60.2- 80 mm dia nominal bore (heavy grade)
NS 60.3- 100 mm dia nominal bore (heavy grade)
NS 61-Providing and fixing UPVC pipes, having thermal stability for hot & cold waste water carring, including all fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (a) Concealed work, including cutting chases and making good the walls etc. (b) 50 mm nominal dia Pipes
NS 62- Providing and fixing soil, waste and vent pipes : (a) 150 mm diameter (b) Centrifugally cast (spun) iron socket & spigot (S&S) pipe
NS 63- Providing and fixing single unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :(a) 150x150x100 mm (b) Sand cast iron S&S as per IS - 3989
NS 64- Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete (a) 150 mm dia (b) Sand cast iron S&S as per IS - 3989
NS 65- Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : (a) 150 mm bore
NS 66- Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (a) Concealed work, including cutting chases and making good the walls etc. (b) 40 mm nominal dia Pipes
NS 67- Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make -cera,cat no-F1013351 & F4050502 or equivalent
NS 67.1- 20 mm nominal bore
NS 67.2- 25 mm nominal bore
NS 68- Providing and fixing Screwed end Bronze Y-Strainer of approved make and ISI marked.
NS 68.1- 15 mm nominal bore
NS 68.2- 25 mm nominal bore
NS 69- Providing, fitting and fixing of foldable horizontal Grab Bar of stainless steel (Make Jaquar or equivalent) for person with disabilities (for WC) Size : 900 X 32 mm
NS 70- Providing, fitting and fixing of vertical Grab Bar of stainless steel (Make Jaquar or Equivalent for person with disabilities. (for wash basin & WC) Size: 600 X 32 mm
NS 71-Supplying & laying High Density Polyethelene Pipes conforming to IS 16098 (Part-II):2013 having Stiffness Class of SN 8with Ring Stiffness not less than 8.00 KN/Sqm. and Impact Resistance TIR value not more than 10% including necessary jointing materials for non-pressure chemical waste application. (a) 75 mm dia
EXTERNAL WATER SUPPLY AND RAIN WATER HARVESTING
NS 72 - Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to sch-40, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. (a) 250 mm nominal size dia
NS 73- Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (a) 250 mm nominal size dia
NS 74- Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
NS 75- Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
Internal work - Exposed on wall
NS 75.1- 65 mm dia nominal bore
NS 75.2- 80 mm dia nominal bore
NS 75.3- 100 mm dia nominal bore
NS 75.4-150 mm dia nominal bore
NS 76- Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc
External work(Under Ground)
NS 76.1- 100 mm dia nominal bore
NS 76.2- 150 mm dia nominal bore
NS 77- Providing and fixing, Water Level Monitor (Water gauge) for installing on the side wall of Water Reservoir consisting of clibrated bore transparent Tube, Floating Indicator, Drain-out Valve etc, complete operational (for Monitoring Water Level Difference upto 4 metres.
NS 78- Providing and fixing, Testing & Commissioning of SS Spring loaded Air-Relief Valve for pressure of 12 Kg/sq. cm. of approved quality with SS Isolation Valve, Tapers, GI Pipes and Specials etc including making necessary screwed / Flanged joints by providing all jointing materials including painting & Testing the joints to Hydraulic pressure specified for Pipes all complete as directed by the Engineer-in-charge. (a) 20 mm dia
NS 79- Supplying fitting & Commissioning of (PRV) Pressure Reducing Valve (screwed), with Bronze/Gunmetal/Brass Body of (PN1.0) class, BSPT(F) threaded.
NS 79.1- 20 mm dia nominal bore
NS 79.2- 25 mm dia nominal bore
NS 79.3- 32 mm dia nominal bore
NS 79.4- 50 mm dia nominal bore
NS 79.5- 65 mm dia nominal bore
NS 80- Providing and fixing, 150mm Dial type Pressure Gauge of of O-to-16 Kg/sq.cm. range with Gun Metal Shut-off Cock etc, duly clibrated before Installation in MKS & FPS Units, and fixing the same where required as directed including all Fittings, Short-piece, Nipples, Elbows, Testing the Joint etc, all complete. (Quantity of this Items will be Payable only where it has not been included in the relevant composite Items).
NS 81- Supply, fitting & fixing of Pressure Switch of 1 - 15 Kgs. Rated; with cable & cocks connected with the M.C.C. Panel as per Technical specifications and as per direction of Engineer in-charge.
NS 82- CI Non Return Valve of 100mm dia, (for Water Supply system). Providing & fixing C.S. "Swing" Flap "Horizontal" / Wafer type Non-Return (Check) valve, with Neoprene / Nitrile seat, complete including matching flanges, Bolts, Nuts, & washers, including necessary "Uni-Klinger" make CAF Gaskets -
NS 83- Hydropneumatic Pump for Domestic Water.
Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted Factory Assembled & Tested Hydropneumatic System along with Single VFD (Locally Assembled set is not acceptable):
a. In-Line, Multistage, centrifugal pumps with SS-304 intermediate casing and impeller and SS-316 shaft, CI with CED Quoted base & head and with IE3 Efficiency Class TEFC motor as per IEC standard (with mechanical seal)
(Vendor to submit performance curves and technical catalog of the proposed model for review & information)
b. External Pump mounted or wall mounted microprocessor based multi pump controller and frequency inverter integrated inside the control panel with pressure sensor transmitter, with larger graphical colour display, diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equiped with dry running protection.
c. Complete (Skid mounted/wall mounted) electrical control panel comprising of all accessories such as controller, pressure Transmiter, control wiring and any other necessary imports etc.
d. Precharged MS diaphram pressure vessel with food grade membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc complete.
e. Set of accessories such as pressure switches, pressure transducers, inter connecting power & control cabling etc. complete.
f. Accessories like pressure gauge, MS base frame (Synthetic enamel painted over a coat of primer)
g. Manifolds should be with GI.
h. Pressure Tank--200L 16 Bar GWS/Zilmet/Nema (1 No)
I. Pump set--KCIL 10-12(4 KW/5.36 HP)--2900 rpm (3 Nos)
J.Control Panel--KBL Control Panel IP54 Equivalent
K. VFD Make--VACON
L. Float Switch--For Dry RUN Protection.
Hydropneumatic System with three Pumps (2W+1S)
Pump Flow rate--3.1 LPS
Head -81m
NS 84- Hydropneumatic Pump for Flushing Water
Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted Factory Assembled & Tested Hydropneumatic System along with Single VFD (Locally Assembled set is not acceptable):
a. In-Line, Multistage, centrifugal pumps with SS-304 intermediate casing and impeller and SS-316 shaft, CI with CED Quoted base & head and with IE3 Efficiency Class TEFC motor as per IEC standard (with mechanical seal)
(Vendor to submit performance curves and technical catalog of the proposed model for review & information)
b. External Pump mounted or wall mounted microprocessor based multi pump controller and frequency inverter integrated inside the control panel with pressure sensor transmitter, with larger graphoical colour display, diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equiped with dry running protection
c. Complete (Skid mounted/wall mounted) electrical control panel comprising of all accessories such as controller, pressure Transmiter, control wiring and any other necessary imports etc.
d. Precharged MS diaphram pressure vessel with food grade membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc complete.
e. Set of accessories such as pressure switches, pressure transducers, inter connecting power & control cabling etc. complete.
f. Accessories like pressure gauge, MS base frame (Synthetic enamel painted over a coat of primer)
g. Manifolds should be with GI.
h. Pressure Tank--100L 10 Bar GWS/Zilmet/Nema (1 No)
I. Pump set--KCIL 15-07(5.5 KW/7.38 HP)--2900 rpm (3 Nos)
J.Control Panel--KBL Control Panel IP54 Equivalent
K. VFD Make--VACON
L. Float Switch--For Dry RUN Protection.
Hydropneumatic System with three Pumps (2W+1S)
Pump Flow rate--3.65 LPS
Head--81m
NS 85- Supply , Installation and commission of Sump pump(1W+1S), Centrifugally cast ,approx Capacity -5LPS at head 9.5 meters with provitional auto & manual starter LTpanel with water level sensor.
NS 86- Design , Supply , installation and Commissioning of 18 Cum/Hr WTP following latest CPHEEO ,MOEF , IS 10500and CPCB guide line .
NS 87- Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of Bore-well as per IS:2800 (part I). (a) 250 mm dia
NS 88-Providing and fixing Top plug of required dia to the top of pipe assembly of Bore-well as per IS:2800 (part I). (a) 250 mm dia
NS 89- Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (a) 65 mm nominal bore
NS 90- Providing and fixing M.S. holder-bat clamps of approved design to 150mm Bore Sand Cast iron/cast iron (spun) pipe embedded in wall and ceiling including cost of cutting holes and making good the walls & celing all complete as per instruction of Engineer in-charge. (a) 150 mm bore
NS 91- Supply , Fitting and Fixing of Cast Iron Foot Valve as per ISI marked and all complete. (a) 150 mm bore
NS 92- Supply , Fitting and Fixing of Cast Iron Foot Valve as per ISI marked and all complete. (a) 100 mm bore
NS 93- Supply , Fitting and Fixing of 50mm bore PTMT Ball Cock complete with Epoxy Coated Aluminium Rod & H.D. Ball
NS 94-Supply , Installation and commission of Garden watering metal pulsating sprinkler with adjustable rotation.
NS 95- Supply , Installation and commission of Submersible Pump of Capacity 15m3/Hr & 50Mtr Head for Bore well including electrical panel.
EXTERNAL SEWERAGE SYSTEM
NS 96- Supplying & laying High Density Polyethelene Pipes conforming to IS 16098 (Part-II):2013 having Stiffness Class of SN 8with Ring Stiffness not less than 8.00 KN/Sqm. and Impact Resistance TIR value not more than 10% including necessary jointing materials for non-pressure underground Drainage, Sewerage & Cross drainage application.
NS 96.1- 150mm internal dia.
NS 96.2- 200mm internal dia
NS 97- Design , Supply , installation and commissioning of 72KLD STP operating on SBR process following latest CPHEEO ,MOEF and CPCB guide line,Tentative component details
Coarse Bar Screen----2nos(1W+1S),Capacity-72 Cum/day,MOC- RCC(M-30)with waterproof plaster, Type of Screen - Manually cleaned, MOC of Bar screen-MSEP ,Size of the Chamber-1.5 m x 0.5 m x 1.0 m (L x W X D),
Fine Bar Screen----2nos(1W+1S),Capacity-72 Cum/day,MOC- RCC(M-30)with waterproof plaster, Type of Screen - Manually cleaned, MOC of Bar screen-MS
Oil & Grease trap with oil Skimmer (skimmer is optional, provided only if free O & G is >10ppm) ---1no, Inlet oil concentration > 50 mg/L,Outlet oil concentration < 10 mg/L,Mechanical Oil Skimmer-1No, Belt type ,Size of the Chamber-1.5 m x1.45 m x 3.0 m (L x W X D).
Equalization Tank---1No,Volume-33.0 m3, Dimension-3.2 M L X3.2 M W X3.5 M SWD+ 0.5 M FB ( LX WX D ),MOC- RCC, Air grid -1 Lot.
Blower for EQT---Twin Lobe Type, Quantity - 2 No (1W + 1S), Capacity - 23 M3/HR, Head - 0.4 Kg/cm2 (g).
Raw sewage transfer pump --- Non- SubmersibleType, Quantity 2 (1W + 1S), Capacity - 5M3/HR , Head - 1 Kg/cm2(g).
SBR tank---2 No, Volume of each SBR tank - 36m3, Dimension of each tank - 2.3 M (L) X 3.2 M (W) X 4 M SWD +0.5M FB( LX WX D), MOC - RCC, Air Diffuser system - 1 Lot, Type of diffuser - Fine bubble diffuser(EPDM)
SBR Blower - ON/OFF on timer basis---Twin LobeType, Quantity - 3 Nos (2W + 1S), Capacity of each blower -74.0 M3/HR, Head - 0.5 Kg/cm2 (g).
Decanter (with Auto valve) --- Floating Decanter mechanism Type, Quantity - 2Nos (1 in each SBR tank), Avg. flow through decanter - 25.0 M3/HR, Capacity of decanter - 20 to 30 M3/HR.
Chlorine Contact Tank---1 No, Volume - 17 m3,Dimension - 2.7 M (L) X 2.7 M (W) X 2.5 M SWD+ 0.5 M FB(LX WX D), MOC - RCC.
Chlorine Dosing System---Dosage - 10ppm, Solution Strength - 6.0%, Pump Capacity - 0 to 6 LPH, Tank Capacity - 100 Ltr, MOC - HDPE/RCC.
Multi Grade Filter---1 No,Diameter of vessel - Ø600mm, HOS of vessel - 1875mm HOS, MOC - MSEP,Hours of operation - 22.0 hrs,Backwash flow -12.0 m3/hr, Backwash time - 10.0 mins, Rinse Time - 5.0 mins.
Sludge Holding tank---Holding period -1days, Quantity - 1 Nos, Volume - 1.8m3, MOC - HDPE TANKS.
Sludge Dewatering poly dosing system---Dosage - 3 kg/ton, Solution Strength - 0.1 %, Pump Capacity - 0 to 10LPH, Tank Capacity - 100Ltr, Agitator for mixing - Suitable to tank dimension, MOC - HDPE.
Sludge Dewatering feed pump---Screw Type,Quantity - 2 No (1W + 1S), Capacity - 0.5 to 1 M3/HR,Head - 5 to 6 Kg/cm2 (g).
Sludge Dewatering unit - Filter Press - Sludge quantity - 16 to 20Kg/day, Sludge Volume - 1.6 to 2.0 m3/day, Sludge consistency - 1.0 % approx.
Filtrate sump----Quantity - 1No, Volume - 1m3, MOC - HDPE.
Filtrate transfer pump---Non-Submersible Type, Quantity - 2Nos (1W + 1S), Capacity - 0.5 to 1 M3/HR, Head - 0.5 to 1 Kg/cm2 (g).
Automation considered with following----- a. Level Switches in Equalisation tank, SBR 1& 2 tank, Chlorine Contact tank, Sludge pit, Filtrate Sump. b. Auto Valves with Limit Switches – SBR 1&2 inlet valve, Decanter outlet valve c. PLC – Non redundant type d. 4.3” HMI d. Pneumatic air for the auto valve actuator.
SOLID WASTE MANAGEMENT
NS 98-Supply and positioning waste collection HDPE Bin of 240 Lt capacity.
NS 99-Supply and inposition of waste collection on site HDPE Bin of 60 Lt Capacity of following colours-Black ,Red & Green.
INTERNAL FIRE PROTECTION SYSTEM
NS 100- Providing and fixing, Testing & Commissioning of SS Spring loaded Air-Relief Valve for pressure of 12 Kg/sq. cm. of approved quality with SS Isolation Valve, Tapers, GI Pipes and Specials etc including making necessary screwed / Flanged joints by providing all jointing materials including painting & Testing the joints to Hydraulic pressure specified for Pipes all complete as directed by the Engineer-in-charge.
( a ) 25mm dia
FIRE EXTINGUISHERS
NS 101- Supply, installation, testing & commissioning of CO2 type Extinguisher of 4.5 Kg weight with MS fixing clamps (wall Hook) arrangement.
NS 102- Supply, installation, testing & commissioning of Water - CO2 type Extinguisher - Cap - 9 litres each, with MS fixing clamps (wall Hook) arrangement.
NS 103- Supply, installation, testing & commissioning of Wet Chemical Fire Extinguisher - Cap - 6 kg each, with MS fixing clamps (wall Hook) arrangement.
NS 104- ABC Powder (stored Pressure type)- 6.0kg capacity - Extinguisher, 'Manual' type, 'wall hanging', with a test pressure of 30 Kg/cm2, each with MS fixing clamps (wall Hook) arrangement.
FIRE DETECTION, ALARM & P.A. SYSTEM
NS 105- Supply, installation, testing & commissioning of short - circuit - Isolators.
NS 106- Supply, installation, testing & commissioning of 'Rise' type Heat Detectors, approved make, with Operating Temperature of ( - ) 10OC to ( + ) 70OC and OPERATING VOLTAGE OF 18 TO 28 V D.C.
NS 107- Supply, installation, testing & commissioning of Multicriteria Detectors, approved make, with Operating Temperature of ( - ) 10OC to ( + ) 70OC and OPERATING VOLTAGE OF 18 TO 28 V D.C.
NS 108- Supplying, fitting & fixing Base of Dectector,Model no-B501
NS 109- Supply , installation, testing & commissioning of Monitor Modules(MMX) for Manual call points .
NS 110- Providing, Installing, Testing & Commissioning Relay Module, all complete.
NS 111- Supply, installation, Testing & Commissioning of 600 Watt Amplifer.
NS 112- Supply, installation, Testing, Commissioning of Telephone Module.
NS 113- Supply, installation, Testing, Commissioning of Fire Fighter Telephone Jack.
NS 114- Supplying & laying 2 core x 2.5 sq.mm copper conductor PVC insulated, sheathed armoured cable - ISI marked.
NS 115- Supply & installation of hp or equivalent desktop Computer full set with colour Printer_hp Pavilion 20-c416il, 19.5-inch Full HD All-in-One Desktop(8GB|2TB|DOS|wireless keyboard & Mouse),Black and Printer will be HP DeskJet 4729 All-in-One ultra lnk Advantage wireless colour Printer.
EXTERNAL FIRE PROTECTION SYSTEM
PIPES UNDERGROUND FOR HYDRANT SYSTEM
NS 116- MS ERW PIPE U/G : 'Heavy' grade Piping for Hydrant system: Supply , fabrication, welding, laying, testing & commissioning of M.S. Black- ERW pipe with bevelled end, "Heavy" Grade conforming to IS-1239 part1, (under ground), with all MS-Black, "Heavy" class Pipe Fittings (viz., Elbows, Tees, Flanges, Reducers) with 'plain/Bevelled' ends, including laying at around 1.0 M below ground level and testing and commissioning, excavation and back filling and also including of at least 4mm thick (supply and fixing) corrosion protection wrapping coating by the tape made up of HMHDPE film with fibre glass Mat reinforced coal tar mix all compositely bonded, as per IS-10221, with (total 4mm thk) of "PYPKOTE" make, and wrapping with all around the under ground pipe, including supply of necessary primer before wrapping application from u/g Main.
NS 116.1- 80 mm NB (IS-1239, P-I)
NS 116.2- 100 mm NB (IS-1239, P-I)
NS 117- M.S. "Slip-on" flanges of 150mmNB. Supply, fitting & fixing of M.S. slip-on flanges required for Valves / or pipe fittings fixing with Hydrant main / Stand post with "Uni-Klinger" make CAF Gaskets.
NS 118- M.S. "Slip-on" flanges of 80mmNB. Supply, fitting & fixing of M.S. slip-on flanges required for Valves / or pipe fittings fixing with Hydrant main / Stand post with "Uni-Klinger" make CAF Gaskets.
NS 119- M.S. "Blind" Flanges of 150mmNB. Supply, fitting & fixing of M.S. slip-on blind flanges required for Valves / or pipe fittings fixing with Hydrant main / Stand post, also with "Uni-Klinger" make CAF Gaskets.
HOSE BOX
NS 120- M.S. Hose Box above Floor mounted type (for Hydrant system). Supply, installation of "Break Glass Open" type M.S. Hose Box 16 SWG CRCA Sheet of size 750 mm x 600mm x 250mm size with double doors, front glass doors, suitable to accommodate 2 nos x 15 mts CP Hose Reels, including 4nos. - 40x40x6mm thick 1200mm long MS Angle Stands and 300mm PCC (1:3:6) Pedestal Cubes; all complete as shown in the drg, suitable for above G.L. mounted. [ all ISI approved].(For Hydrant system)
NS 121- Hose Reels (1 x 15 mts.)- (for Hydrant system). Supply , fitting & fixing of fire fighting (CP) Hose Reels of 1 x 15 mtrs Hose each with gun-metal male & female 63 mm dia coupling binding (ISI marked). (For Hydrant system)
FIRE PUMPS
NS 122- Electric motor driven Hydrant service Main Pump.
Supply, installation, testing and commissioning of Electric driven main fire pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Horizontal single stage end suction backpull out centrifugal of cast iron with CED coated casing, and bronze impeller with stainless steel shaft (SS 420), mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm.at highest and farthest outlet.
b.Suitable KW squirrel cage induction motor, TEFC, synchronous speed 2970 RPM, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection , Class F Insulation,conforming to IS 325,2 Pole , IE3 Efficiency Class, Br Impeller,40C8-shaft,horizontal foot mounted type with Class-'F' insulation, conforming to IEC standard.
c. Pump should cover 150% of the rated flow & head should not be less than 65% of the rated head.
d.M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts, anti Vibration Pad etc as required.
Flow Rate-2850 LPM
Head-105m
NS 123- Electric motor driven Sprinkler Pump.
Supply, installation, testing and commissioning of Electric driven main fire pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Horizontal single stage end suction backpull out centrifugal of cast iron with CED coated casing, and bronze impeller with stainless steel shaft (SS 420), mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm.at highest and farthest outlet.
b.Suitable KW squirrel cage induction motor, TEFC, synchronous speed 2970 RPM, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection , Class F Insulation,2 Pole , IE3 Efficiency Class, Br Impeller,40C8-shaft,horizontal foot mounted type with Class-'F' insulation, conforming to IEC standard.
c. Pump should cover 150% of the rated flow & head should not be less than 65% of the rated head.
d.M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts, anti Vibration Pad etc as required.
Flow Rate-2850 LPM
Head-105m
NS 124-Jockey Pump -(for Hydrant system).
Supply, Installation, testing and commissioning of electric driven pressurisation(Jockey) pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Vertical inline multi stage of cast iron with CED quoted-Base & Head, Br-Impeller, 40C8- Shaft, Mechanical Seal with 415V, 3 Ph, 2 Pole, IP 55, Class F, IE3 Efficiency Class Motor as per IEC standard.
Flow Rate-180 LPM
Head-105m
Speed-2930 RPM
NS 125- Curtain Pump -(for Hydrant system).
Supply, Installation, testing and commissioning of electric driven pressurisation(Curtain) pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Vertical inline multi stage of cast iron with CED quoted-Base & Head, Br-Impeller, 45C8- Shaft, Mechanical Seal with 415V, 3 Ph, 2 Pole, IP 55, Class F, IE2 Efficiency Class Motor as per IEC standard.
Flow Rate-780 LPM
Head-50m
Speed-2920 RPM
NS 126-Electric motor driven Hydrant service Booster Pump. 32m Head(Lab Block Terrace)
Supply, installation, testing and commissioning of Electric driven main fire pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Horizontal single stage end suction backpull out centrifugal of cast iron with CED coated casing, and bronze impeller with stainless steel shaft (SS 420), mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm.at highest and farthest outlet.
b.Suitable KW squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection , Class F Insulation,2 Pole , IE3 Efficiency Class, horizontal foot mounted type with Class-'F' insulation, conforming to IEC standard.
c. Pump should cover 150% of the rated flow & head should not be less than 65% of the rated head.
d.M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts, anti Vibration Pad etc as required.
Flow Rate-900 LPM
Head-32m
NS 127- Water Storage Pump -(for over head fire tanks)
Supply, Installation, testing and commissioning of electric driven pressurisation(Curtain) pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Vertical inline multi stage of cast iron with CED quoted-Base & Head, Br-Impeller, 45C8- Shaft, Mechanical Seal with 415V, 3 Ph, 2 Pole, IP 55, Class F, IE2 Efficiency Class Motor as per IEC standard.
Flow Rate-1000 LPM
Head-81m
NS 128-Diesel Engine driven Fire Pump (for Hydrant system).
Supply, installation, testing and commissioning of Diesel Engine driven main fire pump suitable for automatic operation and consisting of following: complete in all respect as required as per specifications.
a.Horizontal single stage end suction backpull out centrifugal of cast iron with CED coated casing, and bronze impeller with 40C8-shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm.at highest and farthest outlet.
b.Suitable HP, 2150 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete with auto starting mechanism, 1 No. 12V Battery, 12 volts battery charger , 400L Fuel Tank, Oil Level Indicator, Exhaust Piping, Residencial Silencer.
c. Pump should cover 150% of the rated flow & head should not be less than 65% of the rated head.
d.M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts, anti Vibration Pad etc as required.
Flow Rate-2850 LPM
Head-105m
Speed-2150 RPM
NS 129- Pipe support with MS Angles/Channels (for Hydrant, & Alarm system). M.S. Pipe support (ISA 75, ISA 50, ISA 45, ISA 35- all at least 6mm thick) and ISMC 150, & ISMC100, as required, with G.I. "U" Clamps, Nuts, and Bolts, 8mm dia Dash-fasteners etc., including providing Insert plates as required on R.C.C. Columns / Beams / Floors, also welding the Supports to Ladder / Pole / Bridge including concrete grouting inside Bricks / Block walls or Bldg. outside walls or on Terrace, etc, complete in all respects inclusive all consumables, Tools & Tackles etc; and including painting with 2- coats of Red Oxide Primer & 2 coats of Synthetic enamel paint with (Black / Oxford Blue).
NS 130- Providing and fixing, 150mm Dial type Pressure Gauge of of O-to-16 Kg/sq.cm. range with Gun Metal Shut-off Cock etc, duly clibrated before Installation in MKS & FPS Units, and fixing the same where required as directed including all Fittings, Short-piece, Nipples, Elbows, Testing the Joint etc, all complete. (Quantity of this Items will be Payable only where it has not been included in the relevant composite Items).
NS 131- Providing and fixing, Water Level Monitor (Water gauge) for installing on the side wall of Water Reservoir consisting of clibrated bore transparent Tube, Floating Indicator, Drain-out Valve etc, complete operational (for Monitoring Water Level Difference upto 4 metres.
NS 132- Supply, installating at approved location of approved make Fire Buckets each of standard 9 Litres Capacity and of round-bottomed shape, painted white inside and Red outside and Black on the bottom, inscribed with letters "FIRE" in Black & Bold. Cost shall be inclsive of providing MS Stand with roof shed duly painted over a coat of Primer along with six nos. Buckets Hooked in series with the Stand. (Distinctly identified as "WATER" & "SAND").
NS 133-Supply,Fitting and fixing 250mm dia Cast Iron Foot Valve in all complete.
NS 134-Supply,Fitting and fixing Water Flow Meter for 200mm Bore Cast Iron Pipe line in Fire Hydrand Systems in all complete.
NS 135- Supplying,fitting & fixing ABC Dry Powder Type- 5.0kg capacity - Extinguisher, 'Automatic Modular' type, Temperature Rating 57 degree C with MS fixing clamps arrangement in wall & ceiling in required level
ELECTRICAL WORKS
NS 136- Supply of heavy duty Metalic Body Exhaust Fan of 450 mm Dia,1400 RPM with double ball bearing complete with accessories suitable for 230 volt, Single phase AC supply.
Raceways & Accessories
NS 137- Supply,fixing of the following sizes GI Raceway made with 2 mm thick GI sheet including stiffner at required intervals in recessed system in floor including cutting,chipping,plastering in the floor/wall to make make good finish to match with the floor/wall etc. The GI sheet used in raceway shall confirm the IS 277-2003
NS 137.1- 300 x 38 X 2 mm- Triple Compartment
NS 137.2- 150 x 38 X 2 mm -Double compartment
NS 137.3- 150 x 38 X 2 mm -Single compartment
NS 138- Supply,fixing of the of the 350 X 350 X 50 mm GI Juction box with necessary civil works fixed in recessed system in floor including cutting chipping,plastering in the floor/wall to make good finish to match with civil/floor etc.The juction box cover should be made of 2.5 mm thick flushed type stainless steel plate to provide ultimate rigidity & strength.
NS 139- Supply,fixing of the of the 250 X 250 X 50 mm GI Juction box with necessary civil works fixed in recessed system in floor including cutting chipping,plastering in the floor/wall to make good finish to match with civil/floor etc.The juction Box cover should be made of 2.5 mm thick flushed type stainless steel plate to provide ultimate rigidity & strength.
NS 140- Industrial Plug & Socket
NS 140.1- Supply,installation,testing & Commissioning of Industrial Plug- Switched interlock socket outlet-horizontal thermoplastic. Housing in plastic(PBT). Cable entry with knock-outs dia 25mm/M25. for Three Phase supply (IP44) 4Pole(3P+E) 32A
NS 140.2-Supply,installation,testing & Commissioning of Plug for 32A 4Pole(3P+E)(IP44)
NS 141-Light Fixture & Accessories
NS 141.1- Supply ,installation,testing & Commissioning of LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete System efficacy 100lm/watt.Minimum Surge Protection:2.5kV,Power Factor>0.9. (Equivalent to Philips Smartbright BN021C LED20S PSU CW GR S2 or equivalent to approved make )
NS 141.2- Supply ,installation,testing & Commissioning of LED 9W to 10W tube light fitting (2 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.System efficacy of 100lm/watt and P.F >0.9. (Equivalent to Philips Smartbright BN021C LED10S PSU CW GR S2 or equivalent to approved make )
NS 141.3-Supply,installation,testing & Commissioning of round/square shaped Pressure die-cast aluminium powder coated housing LED pane light suitable for 12 W to 14 W with provision for plane front frame with translucent cover fixed to the housing complete. System Efficacy >80lm/watt,Operating voltage-140-270 volt, Surge Protection:2.5kV,P.F>0.9, CRI>80,CCT-6500K. (Equivalent to Philips Green LED Plus DN177B LED12S‐6500 PSU WH or Equivalent approved make )
NS 141.4- Supply ,installation,testing & Commissioning of round/square shaped Pressure die-cast aluminium powder coated housing LED pane light suitable for 9 W to11W with provision for plane front frame with translucent cover fixed to the housing complete. System Efficacy >80lm/watt,Operating voltage-140-270 volt, Surge Protection:2.5kV,P.F>0.9, CRI>80,CCT-6500K. (Equivalent to Philips Green LED Plus DN177B LED10S‐6500 PSU WH or equivalent to approved make )
NS 141.5-Supply ,installation,testing & Commissioning of LED indoor surface downlighter suitable for general lighting. The luminaire should have CRI > 80 and CCT of 6500K.IP20,having minimum system efficacy of 100 lumen/Watt and a system lumen output of 1200 lumens and maximum system wattage of 12 Watts. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 30k burning hours @ design ambient temp 45 deg C. The electronic driver used shall have a power factor >0.9. BIS certification to be provided seperately for luminaire and Driver. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. (Equivalent to Philips Sleek Surface SM250C LED12S-6500 PSU WH quivalent to approved make)
NS 141.6- Supply,installation,testing & Commissioning of round/square shaped Pressure die-cast aluminium powder coated housing LED pane light suitable for 15 W to18 W with provision for plane front frame with translucent cover fixed to the housing complete. System Efficacy >80lm/watt,Operating voltage-140-270 volt, Surge Protection:2.5kV,P.F>0.9,CRI>80,CCT-6500K. (Equivalent to Philips Green LED Plus DN177B LED15S‐6500 PSU WH/ or equivalent to approved make )
NS 141.7- Supplying ,installation,testing & Commissioning of 2x2 Panel recess mounting luminaire with high performance LEDs, suitable for Armstrong/Grid ceiling.CRCA powder coated white treatment and High transmittance opal diffuser. Mimimum System lumen efficacy of >100 lm/W. Lumen Output of 3600 lumens. Wattage 30-36 watt. CRI >80, Color temperature 5700K-6500K, THD <10% and PF >0.95,IP20,IK02.Life class of 50,000 hrs @ L70, Operating Temperature:-0 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50HZ; Internal Surge Protection:2.5 KV; DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.BIS certification for luminaires and Drivers to be provided seperately. (Equivalent to Philips Full glow G5 RC380 LED 36S 6500 PSU ).
NS 141.8- Supplying and fixing of 2x2 Panel recess mounting DALI Dimmable luminaire with high performance LEDs, suitable for Armstrong/Grid ceiling.CRCA powder coated white treatment and High transmittance opal diffuser. Mimimum System lumen efficacy of >100 lm/W. Lumen Output of 3600 lumens. Wattage 30-36 watt. CRI >80, Color temperature 5700K-6500K, THD <10% and PF >0.95,IP20,IK02.Life class of 50,000 hrs @ L70, Operating Temperature:-0 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50HZ; Internal Surge Protection:2.5 KV; DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.BIS certification for luminaires and Drivers to be provided seperately. (for Office area) (Equivalent to Philips Full glow G5 RC380 LED 36S 6500 PSD or equivalent to approved make )
NS 141.9- Supply,installation,testing & Commissioning of Environmental friendly, ultra modern, energy saving, surface mounted, decorative bulk head LED luminaire 10W comprising of high brightness LEDs. Pressure die cast aluminium housing, System Efficacy>100lm/Watt and system lumen of 1100. PF: >0.9,THD<10%, Minimum Surge Protection of 2.5kV,IK09/IP66. (Equivalent to or Philips Endura Bulkhead WT202W LED10S CW PSU S3 PC or equivalent to approved make )
NS 141.10- Supply ,installation,testing & Commissioning of 1 channel DALI controller for controlling upto 64 DALI dimmable Lights,Din Rail mounted. ( Equivalent to Philips Model No : DDBC 120 -Dali Controller or equivalent to approved make ) for Auditorium and Office area
NS 141.11- Supply,installation,testing & Commissioning of Wall Keypad and Switch.( Equivalent to Philips Antumbra PABPE+ DACM Communication Module or equivalent to approved make ) for Auditorium
NS 141.12- Supply,installation,testing & Commissioning of Recess mounted DALI dimmable 20 W Round LED Downlight with pressure die cast Aluminium housing, having 110mm Cutout Dia. Minimum 100 Lumens/Watt system efficacy. LED chip life of 50,000 burning hours at L70. IP 20; CCT 5700K-6500K, CRI> 80. Luminaire and Driver should be BIS registered with Input voltage range of 150V to 270V ( nominal rated voltage – 240V) with minimum 2 KV surge protection, PF >0.85, THD <10%. Manufacturer should have In-House NABL accredited LAB. Manufacturer need to submit Following Certificates - 1) LM79 Test report from In-House NABL accredited LAB; 2) LM80 Test certificate from the LED chip manufacturer; 3) Photobiological Safety test report as per IS 16108 : 2012/EN62471 from LED chip manufacturer. (Equivalent To Philips Green Perform Sleek DN296 LED 20S PSD 6500 or equivalent to approved make ) for Auditorium
NS 141.13-Supply,installation,testing & Commissioning of Chandelier Wipro make: LM53-511-XXX-40-WH or equivalent to approved make
NS 141.14- Suply,fixing,testing and commissioning of MAINTAINED,EDGE ILLUMINATION SIGNS (Exit/Direction signage) with transparent background and green LEDs double sided display,low operation cost with high lamp life and consumption less than 5 Watt, with Ni-cd rechargeable battery of 3 hrs battery back up.
NS 142- ISOLATORS
NS 142.1-Supply,installation,testing & Commissioning of 40A TPN metal enclosure box
NS 142.2- Supply,installation,testing & Commissioning of 63A TPN metal enclosure box
NS 143- AVIATION LIGHT
NS 143.1- Supply ,installation,testing & Commissioning of aviation obstruction light in die cast aluminium alloy housing with interior driver complete with accessories as required. (IP65) Make- equivalent to bajaj model BGAV 302 LED or equivalent to approved make
NS 144- LIFT
NS 144.1- Supply, installation testing and commissioning of lifts(Machine Room Less,Gear Less) of maximum rated load 15 passenger, speed 1.75mps of triplex system travelleing for B1+B2+ G +12 floors of travel height 53 mts approx.. Hair line stainless steel SS304 , centre opening automatic door of fire retardent capacity not less than 2hours without machine room, gear less system inclusive of all accessories, gadgets, car operating panel indicator, door close and open button alarms, colour LCD display, emergency phone, handicapped COP, braille push buttons, star light ceiling finish inside the car, Granite floor finish, and all other devices complying to fire escape, emergency evacuation control, etc. complete in all respect etc. (As per Data Sheet in Technical Specification)( Passenger Lift) Note- Operation of lift is covered under scope of work till the handing over of lifts to client.
NS 144.2- Supply, installation testing and commissioning of lifts (Machine Room Less,Gear Less) of maximum rated load 15 passenger, speed 1.5mps of single system travelleing for B1+B2 + G +12 floors of travel height 53 mts.approx.. Hair line stainlesssteel venyle floor finish, centre opening automatic door of fire retardent capacity not less than 2hours without machine room, gear less system inclusive of all accessories, gadgets, emergency light car operating panel indicator door close and open button alarms, colour LCD display, emergency phone, handicapped COP, braille push buttons, star light ceiling finish inside the car, Granite floor finish, and all other devices complying to fire escape, emergency evacuation control, etc. complete in all respect etc. (Service Lift) Note-Operation of lift is covered under scope of work till the handing over of lifts to client.
NS 144.3- Supply, installation testing and commissioning of lifts (Machine Room Less,Gear Less) of maximum rated load 15 passenger, speed 1mps of single system travelleing for G +2 floors of travel height 8.3 mts approx. . Hair line stainlesssteel venyle floor finish, centre opening automatic door of fire retardent capacity not less than 2hours without machine room, gear less system inclusive of all accessories, gadgets, emergency light car operating panel indicator door close and open button alarms, colour LCD display, emergency phone, handicapped COP, braille push buttons, star light ceiling finish inside the car, Granite floor finish, and all other devices complying to fire escape, emergency evacuation control, etc. complete in all respect etc. Note-Operation of lift is covered under scope of work till the handing over of lifts to client.
Bidder Name
Amount
BRIDGE AND ROOF CO. (I) LIMITED(GSTN-NA)
GARG BUILDERS(GSTN-NA)
SOM PROJECTS PVT LTD(GSTN-NA)
MACKINTOSH BURN LIMITED(GSTN-NA)
Bidder Name
Amount
BRIDGE AND ROOF CO. (I) LIMITED(GSTN-NA)
GARG BUILDERS(GSTN-NA)
SOM PROJECTS PVT LTD(GSTN-NA)
MACKINTOSH BURN LIMITED(GSTN-NA)
Bidder Name
Amount
BRIDGE AND ROOF CO. (I) LIMITED(GSTN-NA)
GARG BUILDERS(GSTN-NA)
SOM PROJECTS PVT LTD(GSTN-NA)
MACKINTOSH BURN LIMITED(GSTN-NA)
BRIDGE AND ROOF CO. (I) LIMITED
SOM PROJECTS PVT LTD
MACKINTOSH BURN LIMITED
BRIDGE AND ROOF CO. (I) LIMITED
SOM PROJECTS PVT LTD
MACKINTOSH BURN LIMITED
BRIDGE AND ROOF CO. (I) LIMITED
MACKINTOSH BURN LIMITED
SOM PROJECTS PVT LTD
BRIDGE AND ROOF CO. (I) LIMITED
SOM PROJECTS PVT LTD
MACKINTOSH BURN LIMITED
SOM PROJECTS PVT LTD
BRIDGE AND ROOF CO. (I) LIMITED
MACKINTOSH BURN LIMITED
SOM PROJECTS PVT LTD
MACKINTOSH BURN LIMITED
BRIDGE AND ROOF CO. (I) LIMITED
stage.html
html • 0.05 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid