Construction of Community center at Bharari Gram Panchyat Murhag Tehsil Thunag Distt Mandi SH C/o Building portion WSSI Septic tank soak pit

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil classifiction of such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth to the dispose point including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Excavation in foundations, trenches etc., in earth work, in all kind of classification of soil lift upto any height stacking the eacavated soil up to leads and lift clear from the edge of the excavation and then returning the stacked soil in 15cm (fifteen centimetre) layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth to the disposal point as directed with in all lead and lift metres including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Foundation frooting and bases of column etcetra and mass concrete.

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, girders bressumers and lintels of any depth in all height from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Edges of slabs and breaks in floors and walls in any width.

Providing and laying M-25 grade design mix of cement concrete 1:1.5:3 (1 cement : 1.5 Sand : 3 graded crushed stone aggregate 20 mm (twenty millimetre) mechanically mixed vibrated and curing complete excluding cost of form work in including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge Foundations,footings bases of columns and the like and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies, beams,girders, bressumers and contilever up to all floor level.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Stone soling/boulder filling dry hand packed in under floor including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified sizes laid in floors, treads of steps and landings on a bed of 25 mm average thickness of cement mortar 1:6 (1 cement :6 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Precast terrazzo tiles hydraulic compressed 20 mm thick (with marble chips of specified sizes) in skirting and risers of steps not exceeding 30 cm in height on 10 mm thick cement plaster 1:3 (1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required)including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 2nd. Class Kail wood as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing particle board lining with butt jointing and nails (frame work and cover fillets to be measured and paid separtely) 12mm (Twelve millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 30mm (Thirty millimetre) thick 2nd class kail wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level in Cement Mortar 1:6(1 cement:6 sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.250x16mm (Two hundred fifty x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250x10mm (Two hundred fifty into Ten mm)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

White glazed tiles 6 mm (six millimetre) thick in skirting risers of steps and dado 12 mm(twelve millimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

White glazed tiles 6 mm (six millimetre) thick in flooring riser of steps and laid on bed 12 mm(twelve millimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In single stanchions composed of rolled steel joists or channels with caps, bases splices , angeles brackets etc. as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge. In gratings framed guard bars, ladders, railling, brackets and similar works.

Steel work welded in built up sections, fabricated in hollow section of TATA or its equivalant in trusses and framed work, including cutting, hoisting, fixing in position in truss and trussed purlins in building and applying a priming coat of red lead paint including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete. as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing rounded hand railing with MS hollow pipe 50mm dia welded in straight length over M.S. flat top of vertical balusters including one coat of red oxide primer complete (M.S. flated balusters of rolling shall be measeured and paid for seperately as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental.

Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter With readymixed paint other than white as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in Superstructure above plinth level up to all floor level in Cement mortar 1:6 (One Cement : Six Sand) including curing complete second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.upto Floor any Level

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 6mm (six mm) plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:5 (one cement : five sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two costs (excluding priming cost on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering with dry distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surface to give an even shade over and incuding priming coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth as per direction of Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust andother foreign matter etc including sand paper smooth complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-1000 (one thousand)litres capacity. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. . 20mm (Twenty Millimetre) nominal bore

15 mm (fifteen Millimetre) nominal bore

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm ( one hundred ten millimetre) nominal size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. 110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre) size. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm (forty millimetre) dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china water closet(European type w.c.pan) cera or equivalent with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand)(seat and cover to be measured and paid for seprately):-(Cera) Ordinary closet with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings extra for pair of hole for pillar tap instead of single hole (Jaquar or ESS-ESS) Flat Back 550mmx400mm (five hundred fifty millimetre into four hundred millimetre) including carriage of matrials with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws . (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) dia MI union for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to bemeasured and paid for separately Flat back type of size 430mm x 260 mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hundred fifty millimetre) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing 600mm x450mm (six hundred millimetre into four hundred fifty millimetre)beveled edge mirror of superior glass mounted on 6mm (six millimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws and washers with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) lead waste pipe for wash basin or sink including check nut including carriage of material with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass bib tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass pillar tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals andas per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) C.P.Brass angle valve without nuts and pipe with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing 300/450mm (three hundred/four hundred fifty millimetre) length 15mm (fifteen millimetre) nominal bore P.V.C connection pipe with brass unions with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm (hundred millimetre) nominal dia PTMT grating round of approved quality and colour with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with 1metre tube with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

Providing and fixing plastic seat(solid/hollow type) and cover for wash down water closet with c.p. brass hinges and rubber buffers:-Solid type (a) white plastic seat and cover with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Constructing manhole with R.C.C top slab in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (one cement : four sand : eight Graded stone aggregate 40mm (forty millimetre) nominal size ) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3(one cement : three sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing (i)inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) and 500 mm (five hundred millimetre) deep including C.I. cover with frame( light duty single (seal ) pattern I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) with 200 mm(two hundred millimetre) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement : three sand )with in all leads and lifts and other incidentals and as per the direction of Engineer-in-Charge.

rajesh kumar suman