SPL REPAIR OF FEEDER FILLER BOXES SUB STN NO 01 THAKURBARI AND OTHER MINOR WORK AT AGE CHARDUAR UNDER GE (N) TEZPUR

Amount

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Supply & spreading in trenches sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

Supply and laying well burnt bricks sub class 'B' in trenches for cable protection of U/G cable all as specified and directed by Engr-in-Charges.

Taking out the existing ACSR Conductor /PVC/XLPE, 1100 volts grade, LT UG electric cable of any size and any type in trenches/ walls/ overhead lione (or) passing through pipes/in floor complete all as specified and directed by the Engr-in- charge Note:- Excavation and Earth work shall be measured and paid separately under appropriate items:-

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 25 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 35 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 50 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 70 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 95 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 150 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Laying only the under ground cable any type obtained from Items No -06 above in trench/wall/floor etc are connecting with suitable cable lugs/sleevs etc and size 185 sqmm 3.5 core complete all as specified and directed by Engr-in Charge .

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 25 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 35 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 50 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 70 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 95 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 150 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply & Lay in trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 185 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply and jointing straight through heat shrink joint kit for PVC/XLPE LT UG cable for 25 to 50 sqmm 3.5/4 core complete all as specified and directed by Engr-in Charge.

Supply and jointing straight through heat shrink joint kit for PVC/XLPE LT UG cable for 95 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply and jointing straight through heat shrink joint kit for PVC/XLPE LT UG cable for 150 to 185 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supply and jointing straight through heat shrink joint kit for PVC/XLPE LT UG cable for 240 to 300 sqmm 3.5 core complete all as specified and directed by Engr-in Charge.

Supplying & laying in repair 50 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & laying 80 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & laying in trenches 100 mm nominal bore, light grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

M&L preparing old painted surfaces by scraping and removing old paints, rust, etc. from steel tubular poles (above the planting depth and PCC copings of 11.0 Metre length Pole) and mild steel cross arms, cable protection pipe, brackets, etc. and applying one coat of red oxide zinc chrome primer, alternate yellow & black strips painting (4 Nos. each strip 200 mm wide) and remaining portion of pole and cross arms, cable protection pipe, brackets, etc. treated with two coats of Aluminium paint, complete all as specified and as directed.

Taking out the existing LT pole of any size and any type complete all as specified and directed by the Engr-in- charge

Supply & erecting steel tubular swaged pole type 410-SP-55 (11.0 Metre long) including cast iron base plate, finial taper plug, cap, mild steel bolts, nuts, screws, including necessary excavation and earth work, PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C1 as in plinth block and coping, disposal of surplus soil to a distance not exceeding 50m and depositing where directed, painting of exposed surafaces of steel tubular poles with two coats of Aluminium paint over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint) from plinth block and numbering of poles, painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed.complete all as specified and as directed.(Exixting Connection two pole structure to four pole structure at Thakurbari Subs staion 1 &2 ,Phulbari ss)

Re Fixing for Steel tubular swaged poles any type and any size after taking dwon with proper shut dwon without damage for pole any location within 100 mts complete including cast iron base plate, finial taper plug, cap, mild steel bolts, nuts, screws, including necessary excavation and earth work, PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C1 as in plinth block and coping, disposal of surplus soil to a distance not exceeding 50m and depositing where directed, painting of exposed surafaces of steel tubular poles with two coats of Aluminium paint over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint) from plinth block and numbering of poles, painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed.complete all as specified and as directed.

M&L for danger notice plate of 1.6 mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with mild steel clamps, bolts and nuts of approved size, for HT, 250 mm X 200 mm complete all as specified and as directed.

Road cutting for passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 25 sqmm 3.5 core. Complete all as specified and directed

M&L for cement concrete in foundation, filling and mass concrete in M15(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate including formwork complete all as specified and as directed.

S&F earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 mm X 4 mm galvanised mild steel strip complete all as specified and as directed.

Supply and fixing 32 mm X 6 mm galvanised mild steel strip for horizontal conductors and down conductors including suitable design of fixing components of galvanised steel as per fig 28 of IS 2309: 1989 complete all as specified and as directed.

Supply , fabrick , install, test and commssiong LT outdoor type bus bar box made out of 3.15 mm thick MS sheet with suitable size of MS angle iron/flat support including painting and epoxy powder coated grey colour, wheather proof and vermine proof with air fins for cooling with locking arragement complete of adequate size to accommodate the following accessories :- (i) TPN 415 Volts Alu bus bar ,800 Amps mounted on suitable insulation. (ii) Cable gland detachable plates for termination of incoming and outgoing cables with suitable nuts and washers etc. (iii) Earth terminal points

Supply , install, testing and commissioning of cubical housing cabinet type LT feeder pillar of outdoor type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 3.15 mm thick CRCA (Cold Rolled Cold Annealed) MS Sheet, Powder coated, CPRI approved having front and rear hinged doors, lifting lugs (2 Nos) , earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers.Necessary foundation work as per manufacturer instraction including foundation and including taking down the old panel required at site and comprising following:- Incoming : (a) S&F for Electrolytic grade high conductivity solid 4 Nos Alu bus bars, rated 800 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - 04 Nos, (b ) S&F for LED Indicating lamps for Main Supply indicating R', Y' B' - 01 Set of 3, (C ) S&F Ammeter and voltmeter digital multy meter Nos -01, (d ) S&F for MCCB 250 Amp 36 KA 4 pole Thermal magnatic setting complete - N0s -01, outgoing : (a ) S&F MCCB of 4 pole of capacity 63 amps, with breaking capacity of 16 KA with fixed thermal & fixed magnetic setting - 03 Nos, (a ) S&F MCCB of 4 pole 160 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting, - 01 Nos

Supply , install, testing and commissioning of cubical housing cabinet type LT feeder pillar of outdoor type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 3.15 mm thick CRCA (Cold Rolled Cold Annealed) MS Sheet, Powder coated, CPRI approved having front and rear hinged doors, lifting lugs (2 Nos) , earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers.Necessary foundation work as per manufacturer instraction including foundation and including taking down the old panel required at site and comprising following:-Incoming : (a) S&F for Electrolytic grade high conductivity solid 4 Nos Alu bus bars, rated 800 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - 04 Nos, (b ) S&F for LED Indicating lamps for Main Supply indicating R', Y' B' - 01 Set of 3, (C ) S&F Ammeter and voltmeter digital multy meter Nos -01, (d ) S&F for MCCB 250 Amp 36 KA 4 pole Thermal magnatic setting complete - N0s -01, ( e ) Change over switch 250 Amp 4 pole front loaded operated 415 volts Nos -01, outgoing : (a ) S&F MCCB of 4 pole of capacity 100 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 03 Nos, (a ) S&F MCCB of 4 pole of capacity 63 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 03 Nos

Supply , install, testing and commissioning of cubical housing cabinet type LT feeder pillar of outdoor type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 3.15 mm thick CRCA (Cold Rolled Cold Annealed) MS Sheet, Powder coated, CPRI approved having front and rear hinged doors, lifting lugs (2 Nos) , earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers.Necessary foundation work as per manufacturer instraction including foundation and including taking down the old panel required at site and comprising following:-Incoming : (a) S&F for Electrolytic grade high conductivity solid 4 Nos Alu bus bars, rated 800 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - 04 Nos, (b ) S&F for LED Indicating lamps for Main Supply indicating R', Y' B' - 01 Set of 3, (C ) S&F Ammeter and voltmeter digital multy meter Nos -01, (d ) S&F for MCCB 320 Amp 36 KA 4 pole Thermal magnatic setting complete - N0s -01, Outgoing (a ) S&F MCCB of 4 pole of capacity 200 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 03 Nos, (b ) S&F MCCB of 4 pole of capacity 160 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 2 Nos ( c) S&F MCCB of 4 pole of capacity 100 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 2 Nos (b ) S&F MCCB of 4 pole of capacity 63 amps, with breaking capacity of 25 KA with fixed thermal & fixed magnetic setting - 1 Nos

Earthing complete with galvanised steel earth plate electrode of size 60cm x 60cm x 6 mm thick burried directly in ground( earth pit not less than 2.25 m deep below the normal groungnd level) with top edgee of the plate not less than 1.5m below normal GL connected to GI earth strip of size 25x4mm by means of bolts, nuts, check nuts washers of GI or steel all as shown in electrical plate No-5 of SSR Part I connected to machanery/equipments installed power house/sub station all as specified including testing on completion. Note No-1 the unit rate shall also include for excavation earth work in any type of soil PCC (1:3:6) type C1 pit RCC 1:2:4 type B-1 cover reinforced with 8 mm dia CTD bars @ 150mm C/C both ways funnel with 15mm bore GI watering pipe 20mm dia bore GI protection pipe wire mesh and copper lugs complete in addition to item No 1(a) to (e) of preamble ( Notes) Under sub heading earthing specified on SI page NO-389 of SSR Part-II 2020.

Supply, installation, commissioning of Glass Top Deep Freezer 400 Ltrs single phase 240 volt, 50 Hz complete all as specified and directed by Engr -in Charge

Supply, installation, commissioning of Refrigrator double door 320 Ltrs single phase 240 volt, 50 Hz complete all as specified and directed by Engr -in Charge

Supply, installation, commissioning of Refrigrator double door 200 Ltrs single phase 240 volt, 50 Hz complete all as specified and directed by Engr -in Charge

S&F for modular 25 Amp motor starter AC switch with two model with socket 25 Amp including indication both red and green complete all as directed

S&F MCB distribution board made of CRCA sheet, powder coated paint comforming of IS 13032, double door fixed in switch boards/wall at various places of capacity 240volt 8 way MCB DB, SPN with 200 Amp rated bus bar shall conform to IP 38 protection incluidng taking down the old one all as specified and directed by Engr-in-Charge.

S&F MCB of rating 240 Volts,SPN 40 Amps including taking down the old one complete all as specified and directed by Engr-in-Charge.

S&F MCB of Single pole of rating 6 to 32 Amps including taking down the old one complete all as specified and directed by Engr-in Charge

S&F sub main wiring complete with two runs of 4 sqmm PVC insulated unsheathed single core multistrand copper conductor cable of 1100 volts grade drawn through new non metalic rigid PVC casing capping on wall alongwith accessories fixed on walls/floors/ceiling with one run of 4 sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor all as specified and directed by Engr-in-Charge. Note:- Two runs of PVC insulated cable 4 sqmm + one run 4 sqmm of earth wire and one run of conduit including accessories shall be measured as one length.

Raj Enterprise (BID ID -3361481)

M/s Brahamaputra Wood Industries (BID ID -3369538)

M/S RSB ENTERPRISES (BID ID -3368787)

AVASANA SOLUTIONS PRIVATE LIMITED (BID ID -3369794)

Anil Kumar Sarmah (BID ID -3369222)

tun baruah (BID ID -3368452)

M/S JALALUDDIN AHMED (BID ID -3369446)