Providing And Erecting AC Machine, Lift, Conference System And Compound Light at New Prant, Mamlatdar and Sub Registrar, Office, Sector-11, Gandhinagar [3rd attempt]

Name of Work Providing And Erecting AC Machine, Lift, Conference System And Compound Light at New Prant,

Mamlatdar and Sub Registrar, Office, Sector-11, Gandhinagar [3rd ATTEMPT]

Fund Head : Deposit Work

Sr. No. Item No. Particulars. Qty. Rate Amount

Signature of Contractor Deputy executive Engineer

C.P Electrical R & B Sub Dn

Name of Work: Providing And Erecting AC Machine, Lift, Conference System And Compound Light at New Prant, Mamlatdar

and Sub Registrar, Office, Sector-11, Gandhinagar [3rd ATTEMPT]

Sr. Quantity Description of Item Rate in Rs. Per Amount

in Figure In Word

Providing and erecting Mains with ISI marked,

1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing Rupees Fifty

1 20 Mtr. pipe of following size (Specifically for control panel, 56.56 Six And Paise Mtr.

relays, power switchgears, motor starters & control Fifty Six Only

wiring) with required size of copper lugs, nuts and

bolts if required. (e) One wire 6.00 sq. mm

(f) One wire 10.00 sq. Mm

15 Mtr. 91.91 Mtr.

Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kv grade ISI marked copper Rupees Forty

2 100 Mtr. wires of following size to be erected as directed. (e) 46.46 Six And Paise Mtr.

1.50 Sq.mm 3 core round PVC sheathed Forty Six Only

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 Rupees Four

V,Power Factor more than 0.95, THD < 10 %, CCT Thousand

3000 K to 5700K,Uniformity ratio >0.45, Luminaire Nine Hundred

3 12 nos efficacy> 100 lumens/watt . LED driver efficiency > 4997.48 Ninety Seven Each

85 %.( fittings required LM-79 & LM-80 And Paise

certificates)(NOTE: Below description have shown Forty Eight

ranges of Wattage capacity of LED fittings.The Only

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection.

(ii) above 48 to 60 Watts Cat-lll

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 Rupees Seven

V,Power Factor more than 0.95, THD < 10 %, CCT Thousand Two

3000 K to 5700K,Uniformity ratio >0.45, Luminaire Hundred Sixty

4 8 nos 7266.95 Each

efficacy> 100 lumens/watt . LED driver efficiency > Six And Paise

85 %.( fittings required LM-79 & LM-80 Ninety Five

certificates)(NOTE: Below description have shown Only

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (B) Flood Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection.

(iv) above 90 to 120 watts Cat-lll

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal Rupees Six

current rating up to 25 A to 100A. with Fixed thermal Thousand One

& magnetic release suitable to work on A.C. supply Hundred

5 1 nos 6173.12 Each

50 c/s. with all internal connections, spreader tinned Seventy Three

copper & complete erected in existing 16 G.M.S. And Paise

housing. Twelve Only

ICS=100% of ICU only Cat III

providing and erecting Miniature circuit breaker Rupees One

single pole 6A to 25A suitable to operate on 240 V Hundred

7 29 nos A.C. system and having breaking capacity 10 KA to 112.11 Twelve And Each

be erected in existing box. confirming to IS Paise Eleven

8828/1996 with ISI Mark Cat.III Only

Providing & erecting 240 V MCB double pole switch

for motor & inductive load (C Curve) having 10 KA

8 breaking capacity & confirms to IS : 8828 in existing

box having following capacity

(B) 40 Amp. Cat.III Rupees Three

2 nos 330.27 And Paise Each

Providing & erecting 415 V MCB Four Pole for Rupees Seven

Motor & Inductive Load (C Curve) having 10KA Hundred Thirty

9 1 Nos breaking capacity & confirms to IS :8828 in existing 737.30 Seven And Each

box having following capacity (c)63 Amp. Paise Thirty

Replacing old and u/s by Providing and Erecting Rupees One

Sheets steel powder coated enclosure suitable for Hundred

incorporating One/Two nos. MCB. Seventy Six

11 1 nos 176.75 Each

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on 3 phase and neutral Rupees Three

415V,50Hz. having characteristic of quick action & Thousand

12 2 nos 3040.10 Each

tripping with all advance feature & do not Forty And

incorporate any electronic component for following Paise Ten Only

Max. rating erected as directed.

(iii) 63 Amps. FP Cat. III

Providing and erecting HOT deep Galvanised iron

strip wire 8 to 16 SWG.

13 8 kg 77.77 Seven And kg

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having

Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing Hundred

14 3 nos 4591.46 Each

resistane mentioned in test Certificate) & having back Ninety One

filling compound of (B) Inner chemical (CCM And Paise

Compound)- Resistivity:- 0.2 ohm / meter testing as per Forty Six Only

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted by

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

15 375 mtrs 140.39 And Paise mtr

necessary clamps or in existing trench / pipe of

following size of cables (C) 4 core 10 Sq. Mm

Making trench in soft soil of suitable width of 90 cm Rupees Fifty

deep for laying cable or locating the fault all over Five And

16 300 mtrs the run and back filling the same and making the 55.55 mtr

surface as normal ground. Five Only

Drilling the road without breaking the road surface Rupees Four

(Asphalt) for laying of cable for feeding power supply Hundred

by making up to following size of holes at both ends Ninety Two

17 35 mtrs 492.88 mtr

complete. And Paise

(A) Up to 100 mm bore dia Eighty Eight

Providing and fixing approved make Perforated C

type cable tray. Made from sheet steel. The cable

tray should be single or double bended as per

required and as per IS 2062/1079 and shall be Rupees Four

coated with hot dip galvanizing as per IS 2629/4759. Hundred

18 50 Rmt. with max 17.5% perforation with coupler plate / Fish 424.20 Twenty Four Rmt.

plate and GI hardware like nut - bolt and washers And Paise

etc. erection with necessary support( included) as Twenty Only

per Specification and as per instruction of engineer

in charge.. (3) 150 X 50 X 1.6 mm Thick

Providing and fixing approved make Perforated C

type cable tray. Made from sheet steel. The cable

tray should be single or double bended as per

required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS 2629/4759. Hundred

with max 17.5% perforation with coupler plate / Fish

19 80 Rmt. 622.16 Twenty Two Rmt.

plate and GI hardware like nut - bolt and washers

etc. erection with necessary support( included) as

per Specification and as per instruction of engineer

in charge.. (5) 300 X 50 X 2.0 mm Thick

Providing & erecting Approved make Power Saving Rupees One

50 Watt Ceiling Fan with double ball bearing ISI Thousand

mark with Condenser 230 volt A.C. 50 Hz 1200 Nine Hundred

20 100 Nos. mm sweep complete having 3blades with 1948.29 Forty Eight Ea.

aluminium blades with , canopy & 30 cm. down rod And Paise

erected with earthing.(Make shall be approved by Twenty Nine

Engineer in charge)) Only

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm Rupees One

length each side and pierced through a 16 Gauge Hundred Eight

21 100 Nos. M.S. box / Heavy Duty PVC box complete erected 108.07 Ea.

concealed in Ceiling with necessary finishing. Seven Only

Supplying and erecting approved make Octagonal

pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box

consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mmX7.5mm Din-Rail for MCB Rupees Five

Mounting, stud type terminal and arrangement for Thousand Five

22 12 nos cable termination to be erected With Suitable 5556.01 Hundred Fifty Each

foundation (Included) as per details given by Six And Paise

manufacturer considering site requirement. One Only

(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia,

mm thickness with 200mmX200mmX12mm base

plate, 4-M16 Bolts and 450mm long with necessary

G.I. J Bolts .Approx weight 37 kg

Supplying & erecting IP 55 grade following size

section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S. Angle

with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected

with cement concrete foundation and 45 cm high

bricks work finishing with plaster etc. hinged double

door internally supported on both side, Rupees

with internal and outside looking arrangement with Sixteen

look and keys in duplicate 35 x 35 x 5 mm M.S. Thousand Six

Angle of Two Nos. one is welded and other with nut Hundred

23 1 nos 16691.26 Each

and bolt for erecting Bakelite sheet. Painting the Ninety One

Section Pillar inside and out side with three tank And Paise

powder coated paint. section pillar roof should be Twenty Six

without joint with water leakage proof & tested as Only

per IP 55 test & followed by IS 2147 of

(A) 150 X 90 X 75 cm section pillar fabricated from

14 Gauge MS Sheet with angle iron legs 95 cm long

made from 40 X 40 X 6 mm thick MS angle.

Supplying and erecting HYLAM sheet on existing Rupees One

angle iron frame.for following thickness (E) 10mm Thousand

24 1 Sq. Mtr. 1927.08 Sq. Mtr.

Replacing Old u/s by new Supplying & erecting

approved make Digital time switch having lithium

cell 6 years operative and operate battery backup

channel day clock with 14 memory programme, Rupees Three

suitable to operate on 240V + 5%, 16A with, floating Thousand One

contacts Minimum switching setup time 1 minimum Hundred Sixty

25 1 nos 3168.37 Each

& LCD display. Also comprised permanent ON/OFF Eight And

switching. Programming switches & housed in fire Paise Thirty

proof thermoplastic enclosure & transparent cover Seven Only

erected as required with necessary connection

erected as directed.

Providing and erecting Inverter based approved

make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor,

hermetically sealed scroll/rotary compressor with

accessories etc. duly connected separately erected

evaporating unit and blower motor with its

accessories by Eco friendly Green gas charging &

Internal copper wiring & Remote control ( 3 star and

above of current year) with necessary core cutting.

(C) for 3 ton capacity- 1/3Phase

8 nos 131862.57 Eight Hundred Each

Supplying and erecting insulated pair of soft copper Rupees Nine

tubing open or concealed including power and Hundred Sixty

27 350 Rmt. control cable,necessary PVC drain pipes for Split 965.56 Five And Rmt.

AC machine up to 4 TR capacity Paise Fifty Six

Providing and erecting Inverter based approved

make split air-conditioning unit consisting of

condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary compressor Rupees Sixty

with accessories etc. duly connected separately Three

erected evaporating unit and blower motor with its Thousand

accessories by means of extra supplied proper Seven

insulated copper tubing,drain PVC pipes suitable for Hundred Sixty

( cost includes Eco Friendly green gas charging and Five And

15A plug top & Remote Control & MS Stand) with Paise Thirty

necessary core cutting. Four Only

(2)For ISEER Range (KWH/KWH)(4.0 to 4.49)

(C) for 1.7 to 2 ton capacity

Providing & erecting water cooler having storage

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour

@ an ambient temp of 45˚ C. The outlet temp. of the Rupees Fifty

water should drop by 15˚C within a hour, The water Five Thousand

cooler should be comprising of hermetically sealed Eight Hundred

compressor, fan motor, condensing unit, water tank Ninety Three

surrounded by evaporating, coil, thermostats, relay And Paise

etc.complete with necessary inlet & outlet Forty Only

connection. The body of water cooler will be made

from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis

water purification system with M.S. powder coated Rupees

frame, prefilter housing with 'O' ring presediment Twenty Nine

filter GAC filter, carbon filter suitable buster DC Thousand One

pump capacity 80 psi, mention with 40 psi inline Hundred

type post carbon filter auto low & high pressure Eighty Seven

switches with following size of storage tank & LPH And Paise

capacity & erected as directed [C] 50 Ltr / Hr with Ninety Nine

150 psi 2 nos booster pump Only

Providing and erecting AC-3 duty 4 pole A.C. Coil Rupees Five

with 2 NO & 2 NC aux contacts complete with Thousand

415V/220V operating coil suitable for (L&T, Seven

BCH,T.C., Siemens, C&S make). (C) for 60 / 70 A Hundred

31 1 nos 5728.72 Each

rating Twenty Eight

Providing Erecting and Testing Of SONY

Bravia/SAMASUNG or Equivalent LED TV 108cm

(43 inch) 4K and above Display: 4K Ultra HD LED,

3840x2160 Pixels, 60HZ Refresh Rate Connectivity:

3 HDMI/2USB/Wi-Fi-Operating System: WebOS-

linus base/Tizen operating System/Android

32 8 nos operating system-google) Apple TV Plus, Netflix, 51828.15 Each

Prime Video, Disney+Hotstar-/ google Sound: 20W

Speaker, with Remote, 4K Upscaling- (Approved by

Competent Authority i.e. not below the rank of

Executive Engineer) (Model no :- K-43S22M2 Or

Equivalent Model)

33 (A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of

High Starting torque Lift 3 phase 440 V A. C.

Permanent Magnet Synchronous motor of proper

rating with high efficiency shall be used.[2] Micro

processor based / PLC, ACVVVF, vector control

drive with encoder feedback closed loop system

shall be used for lift car and door operation which

shall be full collective selective operation hall call

demand response, UP/DOWN hall stops, Main, Up/

Down Contactor with overload and phase reversal

relay and safety controls.

[3] Car with M S platform with bracings of adequate

size and to sustain the impact load cabin +

passenger with safety factor of fire for steel and side

panels of Stainless steel of sheet of grade 304 duty.

Car ceiling will be S.S. finishes with aesthetic

appearance with LED ceiling lights. Car flooring

shall be of s/s 304 chaker plate design sugeested of

engineer in charge. of engineer in charge. Car doors

shall be of stainless steel grade 304, hairline finish

with centre opening / telescopic automatic doors.

Car panel will also be S.S. 304 finished with

emergency stop device, mechanical door safety

device, facility of auto/ attended mode. All car panel

buttons and all floor switches must be with brail

language as per lift act.

[4] All landing doors must be fire rated for 2 hour

shall be fully automatic centre opening/ telescopic

opening made of hairline finish steel grade of

with key holes and infrared curtains with Unlocking

facility from outside

[5] Appropriate battery operated emergency light in

the car along with alarm switch shall be provided.

Also, Emergency Light & Fan should start

immediately without any Time Delay as soon as

[6] Digital scrolling indicator system for up-down

arrow along with floor position indicator shall be

provided inside the car and at all floors.

[7] Full height infra red curtain with multiple cross /

crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be

provided accordingly of passenger capacity with

Manual Rescue Operation ( Manual Cranking

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open

till excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with

automatic sleep timer shall be provided.

[12] Voice annunciator with suitable music shall be

provided in lift car.

[13] Self diagnostics system for operational and

safety parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and

submission of calibration certificate submission,

door key holes in the floor doors, fireman switch

shall be provided.

[15] Lift machine hoisting arrangement in the lift

machine room and monkey ladder for lift pit should

be provided by the lift agency, along with the other

steel structure works, foundations for the machine

[16] In the hoist way fascia plate shall be provided

without any extra cost, where ever required as / if

directed by engineer in charge.

[17] Permanent wiring with necessary safety devices

like RCCB in all circuit, Over Voltage Under Voltage

protection and THD eliminator in circuit for lift

machine room and lift well with proper numbers of

light points, with fixtures, exhaust fan and plug

points shall be provided by the agency. Only

phase Power Supply shall be made available by

department in lift machine room. Necessary

Earthing as per Lift Act/Rules shall be arranged by

[18] Any civil/ electrical works for additional and

alteration in lift shaft and machine room related to

erection of lift shall be made by lift agency without

any extra cost. (granite/marble fixing around all

landing door openings are not in lift agency’s

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all

necessary permission from lift inspector and other

authorities. [20] acrylic transparent

licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of

Gujarat lift & escalator act 2000, lift agency has to

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

third party lift inspection during/after lift erection and

provide report by third party authorized by concern

licensing authority 5.agency has to provide third

party insurance upto completion of free

maintenance period and submit the document for

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly

visible when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should

be provided at appropriate height on the Rear &

Side Wall Panels in Lift Car. [23] With Necessary

KVA rating voltage controlled Stabilizer suitable for

your controller, drive and all equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb

required for lift is in scope of work which rating is

sugested by CEICED Department (electrical

(B) SPECIAL FEATURES DESCRIPTION OF

LIFTS for PREMIUM category

1. Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial

Communication mode including Regenerative power

efficient operation,on site programming facility, Anti

nuisance, Pte-opening, BMS/RMS with necessary

online real time monitoring system having necessary

connectivity for remote monitoring & other suitable

supporting hardware & software devices to fulfil the

2. Floor Indication LCD Display with call registration

& brail mark with arrival gong and hall lantern & TFT

Screen in the car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS

Moonrock finish / Hair Line / Honeycomb for car

and all Doors, All landing doors must have fire rating

up to 2 hours and car door must have multi-level

crisscross beam door protection.

4. To & fro communication system & wiring (i.e. car

control room & guard room ) and Each elevator are

equipped with remote monitoring system.agency

has to provide mobile app and user id and

password for monitoring

DESCRIPTION OF LIFT :

Supplying, Erecting, Testing & Commissioning the

passenger / stretcher lift having following main

15/16 Passengers, Ground plus 4 upper floor

(B+G+3 Floor) with Rated Speed of 1.0 m/sec.,

Fabrication Work For Support Bracket in Lift Well

And Machine Room Railing/Gadar Work In Scope

OF Agency if Required

(C) With General PLUS ADDITIONAL SPECIAL

FEATURES attached herewith. Prem. Cat.

1 Nos. 2155445.04 Each.

SITC of Control Unit shall have features for

managing the number of active microphones and

determining the operating mode, without the need

for a central operator, should be available. It shall be Rupees Ninety

possible to control up to 150 delegate units and Five Thousand

power up to 50 delegate units. It shall be possible to One Hundred

34 2 Nos. connect external equipment to extend the system 95168.26 Sixty Eight Each.

capabilities. There shall be a built-in loudspeaker And Paise

and headphone connector to allow the conference Twenty Six

to be monitored by, for example, a stenographer. Only

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

SITC of Chairman Unit shall enable the user to

function as chairman of a conference or meeting. It

shall be similar in appearance to the Delegate Unit,

and shall also include a ‘chairman priority Rupees Thirty

button.When pressed, the priority button shall cause Eight

all currently active delegate microphones to be Thousand

temporarily or permanently muted, allowing the Seven

35 2 Nos. chairman to take control of the meeting. To prevent 38726.43 Hundred Each.

acoustic feedback, the built-in loudspeaker shall be Twenty Six

muted when the microphone is on, and/or the And Paise

headphones are connected. An optional chime shall Forty Three

be selectable to precede chairman priority calls. Only

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

SITC of Delegate Unit shall enable delegates to

speak and listen to the proceedings via a

loudspeaker or headphones. The unit shall include a

microphone with a red indicator ring, which shall

illuminate when the microphone is on.

The unit shall include a ‘Possible To Speak’ white

LED indicator, which shall illuminate showing the

delegate when it is possible to switch on the

To prevent acoustic feedback, the built-in Rupees Thirty

loudspeaker shall be muted when the microphone is Two Thousand

36 58 Nos. on, and/or the headphones are connected. 32024.07 Twenty Four Each.

Two 3.5 mm stereo headphone sockets (wired for And Paise

mono) shall allow two pairs of headphones to be Seven Only

connected, enabling two delegates to

simultaneously use the unit.

The headphone volume level shall be adjustable on

the unit for maximum comfort. It shall also be

possible to connect a tape recorder to one

headphone socket, and use the other headphone

socket to listen to the proceedings. [Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

SITC of extension cable between the units or Rupees Eight

between the controller and unit -10 meter long Thousand One

[Approved by Competent Authority i.e. not Below the Hundred Four

37 2 Nos. 8104.24 Each.

rank of Executive Engineer ] And Paise

SITC of Ceiling loudspeaker, 6W, ABS with clamps

Suitable for speech and music reproduction

Increased sensitivity

Flush-mounting in ceiling cavity

Easy to install Rupees Three

Protective dust cover Thousand Six

Optional certified fire dome Hundred

Simple power setting Eighteen And

Matching surface mounting box Paise Eighty

Comply with international safety regulations Three Only

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

SITC of Mixer amplifier, 120W [Approved by Rupees

Competent Authority i.e. not Below the rank of Seventeen

Executive Engineer ] Thousand

SITC of 3LCD Lamp based projector having wxga

(1280x800) or better resolution with minimum white

brightness of 3800 lumens and color brightness of

3800 lumens. The projector should have minimum

1HDMI,1VGA input. Having contrast ratio of 15000:1

or more. the projector should have auto vertical key Rupees Thirty

stone correction of +/- 30 degree and Manual Three

Horizontal of +/-30 degree. the projector should Thousand

40 2 Nos. have optical lens, throw ratio 1.30-1.56:1. Zoom 33895.60 Eight Hundred Each.

Factor of 1.2. Lens focus Manual having focal length Ninety Five

16.9mm to 20.28mm. projector should have And Paise

features like AV mute slide, quick corner and split Sixty Only

function and should support wireless functionality

with inbuilt wifi or wifi dongle. [Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

SITC of universal Projector mounting kit, with Rupees Six

necessary grouting, fasteners etc. with adjustable Thousand

height and suitable for all types of projectors. Eight Hundred

41 2 Nos. [Approved by Competent Authority i.e. not Below the 6848.81 Forty Eight Each.

rank of Executive Engineer ] And Paise

SITC of 120 inch Self Lock MW (8 x 6) Instalock

Slow Retraction Screen, Aspect Ratio-4:3 [Approved

by Competent Authority i.e. not Below the rank of

2 Nos. Executive Engineer ]

42 5334.82 Hundred Thirty Each.

Supply, Installation Testing & Commissioning 15 Rupees One

Mtr. HDMI Interface Cable as per the detailed Thousand

Specifications supports transmission of 4K Signals Seven

43 4 Nos. 1777.60 Each.

Supply, Installation, Testing and Commissioning of Rupees Eight

Popup Box with Hdmi, VGA, Power Thousand

44 4 Nos. 8332.50 Hundred Thirty Each.

Supply, Installation, Testing and Commissioning of

4x2 HDMI Matrix Switcher with INPUT: 1 – 4 (4) 19-

pin Type A HDMI female;HDMI digital video/audio Rupees Eighty

inputs; OUTPUT: 1 – 2 (2) 19-pin Type A HDMI Three

female; HDMI digital video/audio outputs; LAN (1) 8- Thousand

45 2 Nos. 83325.00 Three Each.

wire RJ45 female; 10Base-T/100Base- TX Ethernet

port, Communications: Ethernet 10/100 Mbps, auto- Hundred

switching, auto-negotiating, auto- discovery, full/half Twenty Five

duplex, DHCP. Only

Supply, Installation, Testing and Commissioning of

24 U Rack with A full range of accessories can be

loaded with a full security system to prevent

unauthorised access to vital equipments within the

46 2 Nos. 27219.50 Hundred Each.

cabinet, Functional cable management all along the

height, Direct mounting of fan on the top cover

allows maximum height utilization.

Supply, Installation, Testing and Commissioning of Rupees

audio cable with nessasary Connector [Approved by Twenty Seven

Competent Authority i.e. not Below the rank of Thousand

47 2 Nos. Executive Engineer ] 27775.00 Seven Each.

RUPEES IN Rupees One Crore Five Lac Seventy Eight Thousand Seven Hundred Fifty One and paisa Eleven Only

I/We am/are willing to carry out the work at(No above rates allowed) ____________% below ___________________________________

__________________percent (Should be written in figures and words) below the tendered rates mentioned above.

Amount of my/our tender works out as under :

Estimated amount put to tender Estimated amount put to tender

Deduct……………………….. % Below Deduct……………………….. % Above

In words In words

1 I/We hereby declare that I/We have visited the site, fully exquisite myself/ourselves with the local situation regarding materials and

2 I/we hereby declare that I/We carefully studied the conditions of specifications and other tender documents of this work and agree to

3 A tender with any overwriting in percentage (should both in word and figures) rejected out right.

4 Insertions and/or corrections in the percentage quoted ( both in word and figures) resulting into increase in the value of the work

Signature of Contractor Deputy executive Engineer

C.P Electrical R & B Sub Dn