REPAIR/ MAINT OF INTERNAL/ EXTERNAL ELECTRIFICATION, SECURITY LIGHT AND REPAIR/ REPLACEMENT OF PUMP MOTOR, DG SETS AND OTHER MISC E/M WORK AT NHO, DEHRADUN UNDER GE CLEMENT TOWN, DEHRADUN

Amount

Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Material and labour for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked casing caping /surface conduit and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface,provision of CI/Pressed steel terminal switch box for normal piano switch/socket ,with plastic laminated sheet 3 mm thick fixed with brass screw and washers for normal piano switch / socket, or provision of PVC gang box where required along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLSH ) as earth wire connected with main common earth dolly complete all as specified and directed for the following (a) One light/fan/exhaust fan/bell point controlled by one, one-way Piano type switch 5/6 Amp. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switch , one-way Piano type switch complete all specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way Piano type switch complete all specified and directed .

All as per item No 4 above but with 2.5 Sqmm PVC insulated cable( FRLSH) and same size of earth wire for 15 Amps power point.

Supply and fixing switch piano flush type single pole, one-way 5/6 Amps, 240 Volts AC complete all as specified and directed.

Supply and fixing switch piano flush single pole, one-way 16 Amp, 240 Volts AC complete all as specified and directed.

Supply and fixing socket out let 2in 1, 5 pin 5 Amps flush type all as specified.

Supply and fixing socket out let 5/6pin 5 Amp and 15 Amp flush type (multi) suitable for 240 Volt AC all as specified.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:-( i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 14 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

Supply and fix Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fix switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fix modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

Supply and fix modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

Supply and fixing step socket type modular fan regulator 120/280 V , 2 module all as specified.

Supply and fix ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked all as specified.

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings all as specified & directed.

Supply and fix Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fix switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fix modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

Supply and fix modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

Supply and fix in repair socket out let 5/6pin 5 Amp and 15 Amp flush type (multi) suitable for 240 Volt AC all as specified.

Supply and fix in repair stepped type electronic fan regulator flush type 120/280 V all as specified.

Supply and fix in repair step socket type modular fan regulator 120/280 V , 2 module all as specified.

Supply and fix in repair of bell ding dong AC 230/240 Volts all as specified.

Supply & fix in repair capacitor 2.5 mfd for fa

Supply and fix in repair sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed.

Supply and fix in repair sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 4 way with 200 Amps rated busbar all as specified and directed.

Supply and fix in repair sheet metal enclosure double door for MCBs DB TPN (Three Pole and Neutral) 415 Volt AC 4 ways complete all as specified and directed.

Supply and fix in repair load line DBs (TP&N) vertical fitted with Bus bars neutral links Blanking plates double door suitable for TP/ FP Frame MCCB as incommer and out going MCBs 4 ways ,Make all as specified and directed.

Supply and fix in repair MCB 5 to 32 Amp 'B'series 10 KA repturing capacity complete all as specified.

Supply and fix in repair MCB SPN 40 Amp 240 V AC 10 KA repturing capacity all as specified.

Supply and fix in repair MCB TP 63 Amps 240 V 10 KA repturing capacity all as specified.

Repair and replecment of PVC connection 15 mm dia,600 mm long for hot water all as spcified and directed.

Supply and fixing in replacement of LED luminaire 600mm X 600mm, 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glair free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fixing in repair energy efficient LED lights fitting, 9 / 10 watt , 230 Volt, LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed.

S & F LED bollard 8 watt having diffuser at the upper portion acts a beacone of path guidance complete all as specified and directed.

S& F in replacement LED Decorative post top indirect light 15 W for parks garden ways and gate light complete with IP 65 protection all as specified and directed.

Repair and replecment sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRlsh ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade cassing caping / concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed

Repair and replecment sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRlsh ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade cassig caping / concealed in wall along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed /

Disconnecting of electric connection & taking down PVC/XLPE LT cable off sizes, fixing on wall with MS Clamps including make proper/ suitableon wall hole if require & reconnection complete. all as specified and directed

Material and labor for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick weld directly in ground. (earth pit not less then 2.25m depth below ground level at any tyoe of strata) with top edge of the earth plate not less then 1.5m below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate connected by 4.0 Sqmm mm GI strip As earth lead by means of brass nut and bolt thimbles checked nut , washer including concrete chamber of PCC 1:3:6 type C1 (using 20 mm graded stone aggregate ) with fair finish, internal surface of concrete chamber shall be given internal dia 300mmx300mm 15mm thick plaster in cm 1:4 funnel with wire mesh RCC pit cover of 320x320x80 mm size ( 1:2:4) type d1(using 20mm graded stone aggregate) reinforced with xpm all as shown in electrical plate no. 3 of MES SSR part 1(2009) and specified including and provision of GI strip upto 7.5m long with 20mm dia light weight GI pipe protection and water pipe of 20mm bore medium grade including all excavation and earth work and connecting earth strip to panel including testing on completion complete all as specified and directed by engineer incharge. Note - RCC pit cover shall be precast of RCC (1:2:4) type d1 80 mm thick reinforced with xpm weighting not less then 4kg /sq m. in lieu of CI cover. 2. Cost of additional GI strip more then 7.5m will be measured and paid seprately under relevent items.

Supply and fix in replacement Heating element 2 KW capacity, straight, triangular type for Geysers .

M&L earth continuity conductor or main earthing lead fixed to wall on battan or recess or chases or burried in ground or drawn in /pipe or fixed to pole or any other indicated situation for loop earthing etc, as required but 4mm dia galvanised iron or steel wire including down old complete all as specified and directed.

S&F in replacement exhaust fan/ fresh air fan 250 mm sweep plastic body complete all as specified and directed by Eng.-in-charge

S&F in replacement exhaust fan fan 300 mm sweep Matllic body complete all as specified and directed by Eng.-in-charge

S&F in replacement exhaust fan 200 mm sweep plastic body complete all as specified and directed by Eng.-in-charge

S&F LED type street light fitting 90 watts made out of pressure dia aluminium hosing with heat resistant toughened glass and IP-66 protection complete all as specified and directed.

S&F LED type flood fitting 100 watts made out of pressure dia aluminium hosing with heat resistant toughened glass and IP-66 protection complete all as specified and directed.

Supply and fixing in replacement of LED luminaire 1 X 4, 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glair free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F LED type Security light fitting 20watt made out of pressure dia aluminium hosing with heat resistant toughened glass and IP-66 protection complete all as specified and directed.

Supply and fixing in repair energy efficient LED lights fitting, 20 watt , 230 Volt, LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed.

S&F only round shape 6 watt 220 volts AC surface/ concelled type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F only round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement of tharmostat for Geysers as per sample complete all as specified and directed.

Disconnecting electric connection & taking down defective ceiling fans/ Exhaust fans of any sweep and make carefully and dismantling for checking of bearing / bush replacement of defective items oiling, greasing and re-assembling complete all as specified and directed. Note:- (Any item required will be measerured & paid separately under relevent item of sch. 'A')

Hanging/fixing only repaired ceiling fan/exhaust of any sweep and connecting up with and including 3 core flexible PVC copper cable of suitable size from fan to ceiling rose complete all as specified and directed.

Rewinding of ceiling fans of 1200/1400 mm sweep with super enameled copper wire of existing gauge including varnishing, insulation, taping, writing MES No with synthetic enameled paint and testing including fixing of ball bearing and bushing complete all as specified and directed.

Rewinding of exhaust fan of 300/350/450 mm sweep with super enameled copper wire of existing gauge including varnishing, insulation, taping, writing MES No with synthetic enameled paint and testing including fixing of ball bearing and bushing complete all as specified and directed.

S& Fy ball bearing for ceiling fan/exhaust fan of any sweep as required at site complete all as specified and directed.

S & F gun metal bush bearing for any sweep of sweep ceiling fan/exhaust fan as required at site complete all as specified and directed.

Excavation in trenches for laying under ground cables in any type of soil not exceeding 1.5m wide and not exceeding 1.5 M deep and getting out complete all specified and directed.

Returning filling in, including spreading leveling watering and well ramming in layers not exceeding 25cms thick.complete all specified and directed.

Removing surplus excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 M above the starting point complete all specified and directed.

M&L for sand cushioning to under ground cable provided with a layer of 8cm deep before laying the cable and 15cm deep after laying and stretching the cable including hand punning and consolidating complete all specified and directed. Note: for payment purpose, punned thickness shall be measured.

Supplying and laying sub class `B’ bricks modular size with axis of the bricks perpendicular to the axis of the cable as in cable protection cover complete all as specified and directe.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 6 sqmm 2 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 10 sqmm 2 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 16 sqmm 4 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 25 sqmm 3.5 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 50sqmm 3.5 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 70sqmm 3.5 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 95 sqmm 3.5 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

Supplying ,laying, commisioning,and testing of 1.1KV grade XLPE insulated PVC sheathed steel armoured aluminium stranded conductor LT UG cable ( conforming to IS7098) ISI marked in trenches/ducts/through GI pipes under roads of size 185 sqmm 3.5 core complete all as specified and directed Note :- The earth work ,GI pipe shall measured and paid seperately under appropriate item of Sch A.

S&F Aluminium service cable 10 Sqmm two core for any type of connection complete all as specified and directed.

S&F Aluminium service cable 2.5 Sqmm two core for any type of connection complete all as specified and directed.

S&F Aluminium service cable 6 Sqmm two core for any type of connection complete all as specified and directed.

S&F Aluminium service cable 4 Sqmm two core for any type of connection complete all as specified and directed.

Supply and laying in Repair and maintenance of external and internal Water supply pipe line including plumbring work as required at site including necessary fittings and fixtures as directded by Engr-in-Charge for the following sizes ;-

25 mm dia medium grade galvanised tubes

40 mm dia medium grade galvanised tubes

50mm dia medium grade galvanised tubes

80mm dia medium grade galvanised tubes

Repair and replecment of gun metal gate valve iron wheel head screwed both end from iron pipe of size 25 mm dia

Repair and replecment of for gun metal gate valve iron wheel head screwed both end from iron pipe of size 40 mm dia

Repair and replecment of for gun metal gate valve iron wheel head screwed both end from iron pipe of size 80 mm dia

Repair and replecment of for gun metal gate valve iron wheel head screwed both end from iron pipe of size 50 mm dia

Supply and fixing in replacement of CI foot valve 200 mm dia for pipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI foot valve 150 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI foot valve 50 mm dia for pipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI foot valve 80 mm dia for pipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI sluice valve 100 mm dia for pipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI sluice valve 80 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI sluice valve 150 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI sluice valve 200 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI NRV valve 50 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI NRV 80 mm dia fo rpipe line as per sample complete all as specified and directed.

Supply and fixing in replacement of CI NRV 100 mm dia fo rpipe line as per sample complete all as specified and directed.

S& F in replacement of 160 A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 200A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 100A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 250 A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 400 A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 315A MCCB 4pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

S& F in replacement of 40 A MCCB 4 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

Supply and fixing in replacement of Change over Switch Euroload 200A 415 V 50Hz AC S/C current 80 KA Ref IS/IEC: 60947-3 front opreated complete all specified and directed.

Supply and fixing in replacement of Change over Switch Euroload 400A 415 V 50Hz AC S/C current 80 KA Ref IS/IEC: 60947-3 front opreated complete all specified and directed.

Supply and fixing in replacement of Change over Switch Euroload 100 A 415 V 50Hz AC S/C current 80 KA Ref IS/IEC: 60947-3 front opreated complete all specified and directed.

M&L for cleaning of GL, Cleaning of internal surface of ground level water reservoir 26 Thousand gallons capacity 3.8 m deep and size 5.6 x 5.6 m by removing silt, all scales by scraping & cleaning, washing with water and make the surface neat and clean and applying two coats of lime wash on internal and external surface writing date of cleaning and capacity of tank with synthetic enamel paint for the following capacities: Note: (i) Cleaning of tank shall be done through a mechanised water cleaning system. (ii) Mechanized removing of dirty water by high capacity pump set. (iii) Removal of sludge through vaccuum operated pump. (iv) The work shall be executed through reputated specialized water tank cleaner as approved by GE.

All as per item No 108 here-in-before but size of ground level water reservoir sump 10.2x4.2 m and 2.2 deep

ALL as per item No 108 here-in-before but size of ground level water reservoir sump 5.6x4.2 m and 2.2 deep

ALL as per item No 108 here-in-before but size of ground level water reservoir sump 4.0 X 3.8 m and 2.1 deep

M & L for painting of steel tublar pole 9 mtr long straight /tublar and mild steel work such as cross arm, clamp, nuts,bolts etc incl preparation of old painted surface and painting with black and yellow strip 30 cm long starting from black in alternate pattern up to 1.2 mtr height above couping and writting pole No with black paint having existing letter size complete all as specified and directed

Supply and fixing in replacement junction box made from SMC/FRP sheet ready made of size 300 X200X 100 mm having 100 A capacity for RYB and neutral with aluminum busbar with 4 way connector fixed to pole /Wall with MS clamp 25 X 5 mm and nut bolts.including MCB SP 6 Amp 10 KA 240V with aluminium lugs - 01 No

S&F LED type Flood light fitting 100 watts made out of pressure dia aluminium hosing with heat resistant toughened glass and IP-66 protection complete all as specified and directed.

S&F LED type Flood light fitting 150 watts made out of pressure dia aluminium hosing with heat resistant toughened glass and IP-66 protection complete all as specified and directed.

S&F HRC Fuse baseof capacity 630 Amp 440 V complete all as specified and directed.

S&F HRC Fuse of capacity 630 Amp 440 V complete all as specified and directed.

Supply and fixing LED wall light 5 watt decorative single side reflecting complete all as specified and directed by Engr- in-charge.

Comperehensive maintenance consisting of normal repairs with periodical routine maintenance and testing of DG set complete of following as per manufaturere's instruction through authorised workshop/agency as approved by GE for the following DG sets for item Nos. 119.10 to 119.30 (i.e. Engine, alternator, radiator, battery & control wiring etc under GE Clement Town Dehradun, all including consumables like cotton waste cloth kerosene oil etc.) Maintenance will be carried out as under:- (i) Examine suction and exhaust valves in regard smooth operation. (ii) Examine and clean fuel injection, nozzles. (iii)Check clearance of suction and exhaust valves and adjust if required. (iv) Changing of oil filters, fuel filters screen filters assy. (v)Chaning of DCA water filter. (vi) Labour charge for coolant top up. (vii) Change of Hydraulic governor oil. (viii) Change of anerold oil. (ix) Clean alternator winding in position by pressurised air and internal surfaces lubrication of DE & NDE bearings. (x) Tightining of all nut bolts. (xi) Greasing of all points. (xii) Test IR value of alternator winding and recording the readings. (xiii) Checking of any leaking in fuel & oil lines. (xiv) Cleaning of any fuel tank by removing any dirt/forgin particles. Note 1 : DHPP (N) required at the time of mainteance/testing will be issued by MES. Note 2 : Labour charges for dismantling/taking down and replacement/fixing new parts as and when required is deemed to be included the rate quoted by the contractor. Note 3 : Spare parts like oil filter fuel filter, Air flter ect. will be measured and paid separately.

All as per item No.119 here-in-before but 400 KVA capacity - 02 Nos, DG set of Greaves cotton. Location :- MRS (NHO) under GE CLT, D'dun, complete all as specified and directed.

All as per item No.119 here-in-before but 200 KVA capacity - 02 Nos, DG set of Kirloskar/cummins. Location :- Near Press building & P-41, complete all as specified and as directed.

All as per item No.119 here-in-before but 62kva to 75 KVA capacity - 01 No, DG set kirloskar. Location :- Fire fighting pump house, at NHO complete all as specified and as directed.

Supply only lubrication oil filter incl element with 'O' ring set of Make : MICO / Kirloskar / Ruston/ Greaves cotton as required at site for 400 KVA capacities of DG Sets complete all as specified and as directed.

All as per item No. 120 above but for 200 KVA DG set and -ditto-.

All as per item No. 120 above but for 62 kva to75 KVA DG set and -ditto-.

Supply only fuel filter element with 'O' ring set of Make : MICO / Kirloskar / Greaves cotton as required at site for 400 KVA capacities of DG Sets complete all as specified and directed .

All as per item No. 123 above but 200 KVA DG set and -ditto-.

All as per item No. 123 above but 75 KVA DG set and -ditto-.

Supply only Pre line fuel filter element inner and outer as required at site with 'O' set ring of Make : Kirloskar / Ruston/ Greaves cotton as required at site for 400 KVA capacities of DG Sets complete all as specified and directed .

Supply only Air filter element inner and outer as required at site with 'O' set ring of Make : MICO / Kirloskar / Ruston /Greaves cotton as required at site for 400 KVA capacities of DG Sets complete all as specified and as directed.

All as per item No. 127 above but for 200 KVA DG set complete all as specified and as directed.

All as per item No. 127 above but for 62 kva to 75 KVA DG set complete all as specified and as directed.

M&L for lub oil SAE 15 W - 40 for Top up and filling up the oil in the sump (tank) after completely flushing the old oil out of the tank and cleaning of the tank for fresh filling complete all as specified and directed .

M&L for distilled water to be filled in batteries complete all as specified and directed .

Disconnecting, removing and dismantling water radiator assembly of 400 KVA DG set and descaling the radiator thoroughly completely with radiator cleaner solution/ any other chemical solvent agent as approved by the GE, stopping of leakage at place to copper cores and tubes by brazing scrapping the existing oil paint etc, re-installing and commissioning complete all as specified and as directed .

All as per item No 132 above but for DG set of capacity 100KVA to 200 KVA complete all as specified and as directed.

All as per item No 132 above but for DG set of capacity 62KVA to100 KVA complete all as specified and as directed.

Disconnecting the existing battery of capacity 12V, 180 AH from the DG set, taking it to battery workshop, draining out the complete unserviceable electrolyte acid from the battery, filling up with new Electrolyte acid to the required level, charging the battery, testing the battery for correct specific gravity, bringing back to the location, connecting to DG set, start the engine for satisfactory function complete all as specified and directed.

All as per item No 135 above but for capacity 12V, 150 AH battery complete all as specified and directed.

Repairs to 12 V battery charger required for alternator assembly by removing, dismantling, replacing the unserviceable burnt rotor and stator assembly, and re-fixing to the engine and testing for satisfactory charging of battery including all necessary repair complete all as specified and directed

All as per item No 137 above but of 24V battery charging alternator complete all as specified and as directed.

Repairs to 12V self starter by removing, dismantling and taking it to authorised workshop and replacing unserviceable Armature including field coil tapping re-fixing to the engine testing for satisfactory function complete all as specified and as directed .

All as per item No 139 above but of 24V self starter complete all as specified and as directed.

Supply and fixing in replacement and charging maintenance free 12 Volt 180AH battery complete with initial charging including electrolite / distilled water etc and fixing as required at site to the concerned DG Set complete all as specified and directed.

All as per item No 141 above but of 12V 150 AH.

Removing and replacing the old unserviceable AVR (Automatic Voltage Regulator) with new ones of eisting make of generator of capacity 400 KVA, having input voltage 2 phase + neutral sensing voltage 190-264V AC max ,Frequency-50 Hz complete all as specified and directed.

All as per item No 143 above but of 200 KVA complete all as specified and as directed.

All as per item No 143 above but of 63 KVA to 100 KVA complete all as specified and as directed.

S&F in replacement of contactor MN-2, 25 Amps, 415 Volts including 2NO-2NC with new ones complete all as specified and directed.

S&F in replacement of contactor MK1, 10 Amps 415 volts with new ones complete all as specified and directed.

S&F in replacement of contactor MN1.5, 20 Amps, 415 Volts with new ones complete all as specified and directed.

S& F in replacement of 300 A MNX 3 pole, 415 Amps Volts with new ones complete all as specified and directed.

Supply and fixing in repalcement of single phase preventor complete all as specified and directed.

Supply and fixing in replacement of 12V/24V 11 pin PLC relay with base with new ones complete all as specified and directed.

Supply and fixing in replacement of timer relay 12V / 24V. with base with new ones complete all as specified and directed.

Supply and fixing in replacement of indicator lamp/bush button/element all as per sample complete all as specified and directed.

Taking down old UNSV self motor of cap 400 KVA and servicing including replacment of UNSV spare parts such as Brush, holder, solonoid switch, armature bush, field coil complete all as specified and directed.

All as per item No. 155 above but for capacity 62 to 100 KVA DG set complete all as specified and directed.

All as per item No. 155 above but for capacity 200 KVA DG set complete all as specified and directed.

Repair / maint of turbo charger assembly of capacity 400 KVA DG set and servcing all required parts complete all as specified and directed.

All as per item No. 158 above but 200 KVA DG set complete all as specified and directed.

All as per item No. 158 above but 62 to 100 KVA DG set complete all as specified and as directed.

Supply and replacement of Engine controller assembly relay set of Cat Pt No KG-545 of make Kirlosker of capacity 200 KVA DG set complete all as specified and as directed.

Supply and fixing in replacement of rediator hose of existing size and capacity complete all as specified and directed.

Supply and fixing in repalcement of fule hose set nylon type of existing size and capacity complete all as specified and directed.

Supply and fixing in replacement of radiator fan belt of existing size and capacity complete all as specified and directed.

Supply and fixing in replacment of valve door packing of existing size and capacity complete all as specified and directed.

Supply and fixing in repalcement of turbo cooler rubber hose of existing size and capacity complete all as specified and directed.

Supply and fixing inreplacement of radiator mounting set of existing size and capacity complete all as specified and directed.

Supply and fixing in replacement of water pump of any capacity complete all as specified and directed.

Supply and fixing inreplacement of oil seal assembly of any capacity as per sample complete all as specified and directed

Supply and fixing in rpelacement of oil drain hose set complete all as specified and directed.

Disconnecting, taking down of DG set cap 62 KVA to 100 KVA taking in to authorised workshop maintenance of piston assembly complete sets with oiling /greasing etc and checking and repairing of exhaust valve, cyilinder liner, inlet and out let valves, sealing cap, copper washers, thermostat elements, spin filter for lubrication oil, oil seal , valve tappet, gasket for cylinder head, bush for injector, gasket for exhuast manifold,crank case, joint for bearing housing, joint for delivery volute, turbo repair kit complete all as specified and directed.

All as per item No. 171 above but 200 KVA DG set complete all as specified and as directed.

All as per item No. 171 above but 400 KVA DG set complete all as specified and as directed.

Repairing and maintenance of FIP, calibration and testing of fuel pump of 400 KVA capacity DG set and testing on test bench and pump element, delivery valve, ball bearing and adjustment of injectors and setting of fuel pressure complete all as specified and directed .

All as per item No. 174 above but 62 KVA to KVA DG set complete all as specified and as directed.

All as per item No. 174 above but 200 KVA DG set complete all as specified and as directed.

Taking out old painted surface and painting of two coats of synthetic enamel paint over one coat of red oxide of superior quality by spray painting machine for DG set cap 400 KVA in authorised workshop / painter and write their SM / MES No etc., complete all as specified and as directed.

All as per item No. 177 above but 62KVA to 100 KV KVA DG set complete all as specified and as directed.

All as per item No. 177 above but 200 KVA to 250 KVA DG set complete all as specified and as directed.

Taking out old corrugated iron type door hinges of DG set of any capacity and make, S&F new stainless steel 100mm size including nuts, bolts & washers complete set fixed to DG set door complete all as specified and directed .

Supply only coolent for radiator of DG set complete all as specified and directed.

Supply and fix in replacement change over switch 415V in sheet metal enclosures 4 pole of capacity 100 Amps complete all as specified and as directed .

Supply and fix in replacement of 415 VAC 3 phase power contactor type ML 4, 25 AMP with 2NO+2NC with new ones complete all as specified and as directed .

Supply and fix in replacement of 415 VAC 3 phase power contactor type ML6, 25 AMP with 2NO+2NC with new ones complete all as specified and as directed .

Supply in replacement of 415 VAC 3 phase power contactor type MNX 650 AMP with 2NO+2NC for 400 kva DG set with new ones complete all as specified and as directed .

Disconncetion and dismentalling of burnt out exciter from 400KVA DG set and rewinding of stater with copper wire (as per existing gauge ) & refixing the same at site testing complete all as specified and directed .

Disconnecting, decoupling, dismantling of pump motor of following capacity from foundation/base frame, repair and refixing the same on its position , recoupling, reconnection, testing of commissioning complete all as specified and as directed . (Note :- Repair work shall be measured and paid separately under respective item of Sch 'A'.)

All as per item No. 187 above but 60 HP cap and -ditto-.

All as per item No. 187 above but 15/20 HP cap and -ditto-.

All as per item No. 187 above but 10 /7.5 HP cap and -ditto-.

All as per item No. 187 above but 5/3 HP cap and -ditto-.

M&L for rewinding of induction motor, 3 phase, 440 volts with super enamelled copper conductor of existing size and gauge including varnishing, drying, cleaning of slots, repair to damage slots, maching work of shaft for fixing of bearing and other required work for smooth functioning of motor, testing at work shop complete all as specified and directed of the following capacity of motors :-

For 20 HP cap.

For 10 HP cap.

For 7.5 HP Cap.

For 3/5 HP Cap.

M&L for dismantling of centrifugal pump set work shop taking out defective parts and replace the defective parts in pump set, metling, grinding, machining work, as required to make as per original shape and size and assembly for pump set, testing at workshop complete all as specified and directed for the following capacities :-

For 60 HP cap.

For 15/20 HP cap.

For 10HP cap.

For 7.5 HP Cap.

For 3/5 HP Cap.

M&L for rewinding of submersible motor by means cutting & removiang existing unservieable winding, cleaning & repair of slots and winding with new insulated copper winding wire of eixsting gauge & size assembling the motor complete testing at workshop and transport at site complete for the following capacities :-

For 15 to 20 HP Cap.

For 7.5 HP to 10 HP Cap.

For 3.0 to 5.0 HP Cap.

M&L for repair to submersible pump by means transporting to workshop, dismantling parts and replacement of defective /wornout parts such as shaft key, neck rings , bushes, maching work welding, grinding etc, as required, re assembling the pump set for the following capacities :-

For 15 to 20 HP Cap.

For 7.5 HP to 10 HP Cap.

For 3.0 to 5.0 HP Cap.

Lifting of submersible pump set of any cap from borewell carefully with coloumn pipe of size upto 80 mm dia flanged/socketed MS/GI, 3 mtr each length (18 to 50 Nos of pipe) along with existing submersible electric cable and shifting the pipe aside for reuse complete all as specified and directed.

Lowering of submersible pump set of any cap into the borewell carefully with column pipe of size upto 80 mm dia flanged/socketed MS/GI, 3 mtr each length (18 to 50 Nos of pipe) along with existing submersible electric cable binding with GI/Al wire including making joint to submersible cable complete all as specified and as directed. (Note :- Rubber gasket, jointing material , nut, bolts, washers shall be inluded in the unit rates quoted by contractor.)

Supply and topping up insulating transformer oil confirming to IS 335 1993 to the transformer complete all as specified and directed.

DIsconnecting cable from HT /LT side of Transformer and decanning transformer oil as required and dismantling of top cover of transfomer for replcement of HT /LT burntout bushes reassumble & reconnection the cable, refilling transformer oil commissioning, testing complete all as specified and as directed .

Supply and fix in replacement of LT bushes 440 VOLT with rode, washer complete all as specified and directed.

M&L for painting steel and iron surfaces of any descrption , over 10 cm in width or grith not other wise described with one coat of synthetic enamelled paint including preparation of old painted surface complete all as specified and directed.

Taking out old paint surface and painting of two coats of sythetic enamel paint over one coats of re oide of superior quality by spray painting machine for centrifugal pump, motor, Starter panel with authorised work shop/painter and write their SM/MES No etc of following capacity complete all as specified & as directed :-

For 20/60 HP cap.

For 15/7.5 HP cap.

Supply, fixing, jointing and testing submersible cable copper conductor, stranded, PVC insulated and PVC sheathed , 1100 Volts grade, 3 Core, 10Sqmm nominal area, ISI marked complete all as specified and directed.

Supply and fixing in replacement of Fully automatic Star Delta starter 20 to 25 HP for submersible Pump Complete all as specified and directed.

Supply and fixing in replacement of Fully automatic Star Delta starter 15 HP for submersible Pump Complete all as specified and directed.

Supply and fixing in replacement of Star DOL starter 5to 10 HP Complete all as specified and directed.

Supply and fix in replacement of u/s Governer control card suitable /as per sample for 400 KVADG sets complete all as specified and directed.

Supply and fixing in replacement of u/s voltmeter 0 to 800 volt of 400 KVADG sets complete all specified and directed.

Supply and fixing in replacement of u/s ON delay relay of 200/400 KVADG sets complete all specified and directed.

Supply and fixing in replacement of u/s Over voltage relay of 200/400 KVADG sets complete all specified and directed.

Supply and fixing in replacement of u/s under voltage relay of 200/400 KVADG sets complete all specified and directed.

Supply and fixing in replacement of u/s over load relay of 200/400 KVADG sets.complete all specified and directed.

Supply and fixing in replacement of u/s over Trasperent auxilary relay of 400 KVADG sets complete all as specified and directed.

S& F in replacement of 63 A MCCB 3 pole, 415 volts 36 kA 50Hz with themal and magnetic release. with new ones complete all as specified and directed.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

KAPOOR ELECTRICALS (BID ID -3315299)

Pal Engineering Services (BID ID -3322359)

Bedi Refrigeration Works (BID ID -3315135)