SPL REP TO BLDG NO. T-79, SPL REP TO BLDG NO. T-33, SPL REP TO BDLG NO. T-43 AND T-88, SPL REP TO BLDG NO. T-70, T-72, T-76, T-77, T-78, T-64, SPL REP TO BLDG NO. T-15, SPL REP TO COVERED DRAIN IN COOK HOUSE AND OR BATHROOM AND SPL REP TO BLDG NO. T

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Reinforced Cement Concrete in any Position not otherwise specifically Provided for and Removing Debris, etc. to a distance exc. 50.00 Metre and not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work, Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. including Serviceable Bricks keep in Safe custody for Re-use at Site, complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Chowkat or Frame (without Taking Off Shutter from the Frame) of any description, not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre not exc 4.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Rusted/ Worn out Wire Cloth/Netting of any descrip-tion, fixed with Beads, etc., complete all as specified and as directed.

Hacking out Old Broken Glass (any thickness, Size, quality or description) from Wooden or Metal Frame or Stone, Concrete or Brick surrounds including hacking out old Putty or Removing Beads, etc., Punching or Drilling out Old Glazing Pins/ Spring Clips, complete all as specified and as directed.

Dismantling Wrought and Mild Steel Work of any description and from any Situations, complete all as specified and as as directed.

Dismantling Structural Steel Work of any description and from any Situations, complete all as specified and as as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Seggregating Serviceable Steel Sheeting and keep in Safe Custody for Refixing, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers of any descriptions but except Wall and Ceiling Boards, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, Segregating the Serviceable Pipes and Connections, Stacking properly at Site(s) and Keep in Safe Custody for Re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, Segregating the Serviceable Pipes and Connections, Stacking properly at Site(s) and Keep in Safe Custody for Re-use, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Surface Channels and Drains, etc. including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Extra for Forming Fair finished Drain or Channel not exc. 30 Cm Inner Girth in Cement Concrete, using Extra Cement including Forms, Moulds, Stopped Ends, etc., complete all as specified and as directed.

M&L Extra for Forming Fair finished Drain or Channel not exc. 30 Cm Inner Girth in Cement Concrete, using Extra Cement including Forms, Moulds, Stopped Ends, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregates) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregates) in Lintels upto 1.50 Metre Clear Span, Cills, Steps; Seismic and Other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings upto 600mm in Height, Copings, Kneelers, Apex Stones, Bed Plates, Water Troughs and the Like including Weathering, Slightly Rounded or Chamfered Angles and Throating, Finishing all Exposed Faces of Concrete including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and setting in Cement Morter 1:6, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Beams, Cantilevers, Bressummers, Lintels Over 1.50 Metre Span and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, Rough Finished Surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunch-ings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished Surfaces of Concrete, complete all as specified and as directed.

M&L Machine Made & Pressed Pre-cast Cement Concrete Block Masonry with Solid Blocks 300x200x200mm or 300x200x100mm in Sizes, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in width and setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregates) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Scantling in Frame Work of Wall Panelling or fixed in any Position with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectan-gular or Triangular in Section, secured with Nails, Cross Sectional Area exc. 3.00 Sq Cm but not exc. 6.00 Sq Cm, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectan-gular or Triangular in Section, secured with Nails, Cross Sectional Area exc. 6.00 Sq Cm but not exc. 13.00 Sq Cm, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 30mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open Rebated and Prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing Plain, Chamfered or Rounded. fitted with Cut and Mitred Beads for securing Glass, etc.; Sizes of Members of Shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open Rebated and Prepared to receive Glass, Gauze, etc., Divided into Squares, with Plain, Chamfered or Rounded, Mitred and Rebated Sash Bars any Numbers,with Edges of Sash Bars and Framing Moulded fitted with cut and mitred Beads for securing Glass, Gauze, etc.; Sizes of Members of Shutters as specified in SSR Part-I, Section 8 Clause 8.4(b) and fitted to Chowkat, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each and Re-fixing the Shutter in Same Opening including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder coated (Thickness of Powder Coating not less than 50 micron) Door Shutters, Aluminium Section weighing not less than 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber/ Neoprene Packing, Handles (as approved) - 2 No. in Each Door, Stainless Steel Hinges of Size as ordered, Anodised Aluminium Snap Beading, Screws, etc, complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deemed to be included in the Quoted Unit Rate.

M&L Anodised Aluminium Powder coated (Thickness of Powder Coating not less than 50 micron) Window and Ventilator Shutters, Side Hung type, Without Sash Bars, Aluminium Sections weighing 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings such as Peg Stay 150mm long (01 No.), Hinges Type B-21 100mm long (02 No.), suitable Handle (01 No.). in Each Shutter, etc, complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deemed to be included in the Quoted Unit Rate.

S&F Anodised Aluminium Powder coated (Thickness of Powder Coating not less than 50 micron) Window/ Ventilator Frame and Side/ Top Hung or Multi-Track Sliding Shutter complete and fixed with Fittings, One or More Rebates including Jointing Cleat, Glazing Clips, Rubber Neoprene Packing, Aluminium Snap Beading, Screws, Anodised Aluminium Fittings, Rollers, Locking System, etc. complete all as specified and as directed. NOTE :- (a) Sheet Glass, Particle Board, Hinges, Handle, Floor Spring, Hydraulic Door Closer will be Measured and Paid separatly under approprate Items. (b) Aluminium Frame with Shutters shall be fixed in Position in the Wall Opening as required according to Site Conditions including all Fastening Arrangemennts, etc (c) The Gap shall be Sealed Externally with Polysulphide Sealant and Finished Flush with the Surface.

S&F Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain colour PVC Sheet Reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain Color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/ sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement and fixing in the Frame with Butt Hinges as per Site as per Specifica-tion and Drawing of MES Schedule, complete all as specified and as directed. NOTE : Builders Hardware will be Measured & Paid seperately under appropriate Items.

S&F Aluminium anodised Barrel Tower Bolt, 125mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy anodized, Sliding Door Bolt 300mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Section and fixing Bolts and Sliding Bolts of Extruded Section, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm, complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 125mm, Cast type, complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 150mm, Cast type, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Mild Steel 375mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Brass Mortice Lock of Size 100mm, 2 Levers, Vertical type, complete all as specified and as directed.

S&F Floor Door Stopper of Aluminium Alloy Body and Tongue, Anodised, with Hard Drawn Steel Spring, Overall length of Cover Plate 150mm, fixing in Floor, complete all as specified and as directed.

S&F Door Closer, Hydraulically Regulated, Aluminium (Extruded Section) Body, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in Width and of Weight between 61.00 KG to 80.00 KG, complete all as specified and as directed.

S&F Galvanized Mild Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Galvanized Mild Steel Wire Cloth 0.56mm nominal dia of Wire and average width of aperture 1.18mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Galvanized Mild Steel Wire Cloth 0.63mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F factory made Aluminium Powder coated decorative grill for Windows and Ventilator with one or more rebates including jointing cleats/beading 'U' or 'H' channel for fixing etc. complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Steel Pins/Clips in Square not exc. 0.50 Sqm in Each Pane to Steel Windows, complete all as specified and as directed.

S&F Sheet Glass 5.5mm thick, Plain, Ordinary quality and Glazing in Aluminium Frame Work with necessary Jointing Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, complete all as specified and as directed. NOTE : Jointing Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, etc. will be Measured and Paid separatly under BOQ Item No. 1.040 to 1.042 here-in-before.

S&F Solar Control Film 25 Micron Reflective Type Sticked to Glass Panes of any Size and thickness as per Instructions of Manufacturers, complete all as specified and as directed.

M&L TMT Bars 8mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Work in Frame/ Chowkhat for Doors of Angle or Other Section and to be prepared for Hanging with either Hooks and Hinges or Hanging Door Fittings also Fastening and fixing, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Framed Works such as Grills, Gratings, etc. with Ends of Bars shouldered and/or riveted or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walkways; Railings; Framework of Water Tanks and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

S&F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rain Water, Ventilating Pipes including Bolts (if required), Heavy Hooks (Stay) for Large Gates; Hook and Pintle Hinges, Large Hasps and Staples; Chains; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x4.0mm); Wall Ties; Hooks for Hanging Fans; Plain Angle Cleats for securing Purlins to Wood Trusses or Rafters; Knee Piece inserts; 2-way and 3-way Straps, Plate Washers and Similar Small Articles, conform to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel Sections in Joist, Channel, Angle, or Tee Sections in Vertical Post, fixed independently, without Connecting Plates, etc. (cut to ordinary Lengths i.e. within 20mm of the Length indicated), conforming to Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

S&F Factory made Steel windows with side Hung Shutters including Projecting Type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Factory made Steel windows with side Hung Shutters including Projecting Type Hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Re-fixing only Corrugated Mild Steel Sheeting (except Sheets, Serviceable Sheet obtained from BOQ Item No. 1.012 here-in-before) with Two Corrugation Side Lap, fixing with and including providing L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Re-fixing only Plain Mild Steel Sheeting (except Sheets, Serviceable Sheet obtained from BOQ Item No. 1.012 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Aluminum Anodised Snap Grid/ Frame Work of Size 605x605mm in Ceiling, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 595x595x6.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Plywood 6.0mm thick, BWR Grade, Type BB, fixed with Screws to Timber Frame Work, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 100mm thick in Sub-base to Floor, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc. including maintaining Level Uniformly, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Chequered Cement Concrete Coloured (Terracota Red) Tiles 200x200x25mm thick, Set and Jointed in Neat Cement Slurry in Floors and Pointed in Grey Cement, laid over and including 20mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality and/ or as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles, Joins Free, 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality and/ or as approved) in Floors, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Glazed Ceramic White Tiles 300x200x7.0mm thick (1st quality as approved) conforming to IS:13753 in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregates) 75mm thick in Plinth Protection, etc, Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Fair and Even without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured & Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing old decorated surface of Ceiling and applying One Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing Old Distempered and Painted Surfaces of Walls by Washing, Rubbing down and Stopping of Surfaces and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 1.5mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening, (Priming Coat) complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls by Washing, Rubbing down and Stopping of Surfaces and applying One Coat of Cement Base Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, Over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/Distrubed Surfaces and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin of Size 550x400mm, with Pedastal, Flat Back including Brass Chromium plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of Low or High density, a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but excluding Taps, Chain, Plug & Porocelain Stopper and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 LITRE capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia) for suitable Length, a Pair of Cast Iron Brackets Erecting Stand duly painted including Cutting, Pinning in Ends and Making Good to Distrubed Surfaces and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light/Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets (but excluding Light Fittings of any description), etc., Making Good Disturbed Surfaces of Walls/Ceillings, etc. in Cement Mortar 1:3 including Providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire for ONE 6 AMP 5 PIN SOCKET OUTLET POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 6 AMP, 3/5 PIN SOCKET OUTLET on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 16 AMP, 6 PIN SOCKET OUTLET on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Rigid Non-metallic PVC Conduit of Size 20mm (External Dia) exclusive of Boxes (Junction/ Terminal) but inclusive of all Tees, Bends, Elbows, Reducers, Bell Mouth Tube Ends and Fixing Accessories such as Couplers, Lock Nuts, Saddles, Pipe Hooks, etc. including Taking down/ out Unserviceable PVC Conduit Pipe, complete all as specified and as directed.

S&F PVC Rectangular Block of Size 350x300x50mm Deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out Unserviceable PVC Block, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 5 Pin, Multi-plug, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 2 in 1 3 Pin, Multi-plug, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, Fixed-in-Repair complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Decorative LED Light Fitting 1x10 Watt Bulkhead Luminaires including LED Light, Driver, Holder and Connecting up with suitable Length and Size 3 Core Twisted Flexible Copper Conductor Cable including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

S&F LED Tube Light Fitting 1x20 Watt, T-08 complete with 20 Watt T-8 LED Batten/ Rod and mounted on 2 No. PVC Box suitable for fixing of Tube Light Fitting and Connecting up with suitable Length and Size 3 Core Twisted Flexible Copper Conductor Cable including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

M&L Taking down Ceiling Fan/ Exhaust Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing and Repairing, complete all as specified and as directed.

M&L Opening Body of Ceiling Fan 1200mm Sweep in presence of JE-in-Charge/ Engineer-in-Charge, Checking for Repair Works involving, Transporting Ceiling Fan from AGE E/M Store Yard at ALONG to nearest Workshop, Taking out carefully burnt out Winding of any type from the Fan of any Make, Cleaning of Slots, Rewinding Fan Motor with Super Enamalled Copper Wiinding Wire of suitable Gauge and Weight (not less than 350 Gram) providing New Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Ceiling Fan/ Exhaust Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Re-hanging only Ceiling Fan or Re-fixing only Exhaust Fan (Serviceable Ceiling Fan/ Exhaust Fan obtained from BOQ Item No. 2.016 here-in-before after repaired) and Connecting up with and including suitable Size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F MCB 6 Amp to 32 Amp, Single Pole, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting up incluing Taking down/out Old Unserviceable MCB of any description, complete all as specified and as directed.

S&F MCB 40Amp, Single Pole & Neutral, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting upincluing Taking down/out Old Unserviceable MCB of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-way, SPN, 240 Volt, Double Doors, IP-43 Protected, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down Unserviceable Sheet Metal Enclosure of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-way, SPN, 240 Volt, Double Doors, IP-43 Protected, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, including Taking down Unserviceable Sheet Metal Enclosure of any description, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion,including Taking down/out Old Unserviceable Earthing of any description complete all as per specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and/or Laying of UG Cables, Water Pipes Lines, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the UG Cables, Water Pipes Lines, etc. with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

S&F Supply & Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed 10 Sqmm Nominal Cross Section, 2 Core in Service Connection including Taking down old unserviceable cable complete all as specified and as directed.

M/s O DARANG ENTERPRISES

M/s AGAM CONSTRUCTION

M/S S P ENTERPRISES