CWE/AF AMB/SAR-35/2023-24 ADDN / ALTN / IMPROVEMENT TO E/M INSTALLATION AT AFS DEHRADUN UNDER GE (AF) SARSAWA

Amount

Excavation in trenches, not exceeding 1.5mtr wide and not exceeding 1.5mtr in depth; for foundation, laying pipes/cables etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10sqm on plan & not exceeding 1.5mtr in depth and getting out, in soft/loose type of soil complete all as specified & directed. Note: Wherever the work shall be executed for pipe lines, the bottom surface shall formed to required level & slope without any extra cost to department.

Returning, filling in including spreading leveling watering and well ramming in layers not exceeding 25cm thick each in soft / loose type of soil complete all as specified & directed.

Removal of excavated soil to a distance exceeding 1.50 Km but not exceeding 5.00 Km & depositing where directed complete all as specified & directed.

M&L plain cement concrete (PCC) 1:4:8, type D2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished flat surfaces of concrete complete all as specified & directed.

M&L formwork to sides of pillars, posts, struts, piers, columns & stanchions; square, circular rectangular on plan or polygonal in shape for fair finished flat surfaces of concrete complete all as specified & directed.

M&L reinforced cement concrete (RCC), nominal mix, Type B1, 1:2:4, using 20mm graded mechanically crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified & directed.

M&L reinforced cement concrete (RCC), nominal mix, Type B1, 1:2:4, using 20mm graded mechanically crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified & directed.

M&L mild steel TMT bars 10mm dia and over, Fe500/Fe500D grade confirming to IS-1786, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

M&L mild steel TMT bars 6mm dia and over upto & inculding 10mm dia, Fe500/Fe500D grade confirming to IS-1786, cut to length cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacer & binders complete all as specified & directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde-E-250), quality-A complete all as specified & directed.

Dismantling and taking down of rolling shutter any type, size exceeding 4.00 sqm but not exceeding 8.00 sqm complete all as specified & directed.

S&F rolled mild steel work in tubular truess, purlin, rafter, columns etc including welding, butt welded tubes confirming to IS-1161-1979 grade St-240 complete all as specified & directed

S&F rolled mild steel work as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.conforming to Fe 290 (Gde-E-165) complete all as specified & directed.

S&F welded steel wire fabric, weight not exceeding 4.0 Kg per Sqm complete all as specified & directed.

Taking down cement plaster on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water including removal of debries to distance exceeding 500mtr from site complete all as specified & directed.

M&L rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified & directed.

M&L rendering 15mm thick in cement mortar 1:4 on stone masonry or surface other than fair face of brick work masonry of wall mixed with Water Proofing Compound(WPC) as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note : WPC shall be measured & paid separately.

M&L preparing newly plastered surfaces of walls and applying three coats of white lime wash complete all as specified & directed

M&L preparing newly plastered surfaces of walls and applying two coat of cement base paint of approved tint over & including one coat of alkali resistant primer complete all as specified & directed

M&L preperation of old plastered surface of wall and applying two coats of white lime wash complete all as specified & directed.

M&L preparation of old plastered surface of ceiling / soffits and applying two coats of white lime wash complete all as specified & directed.

M&L preparation of old plastered surface of wall and applying one coats of cement base paint of approved tint complete all as specified & directed.

Supply only integral water proofing compound (WPC) complete all as specified & directed.

M&L plain cement concrete(PCC) 1:2:4, type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in lintels upto 1.5mtr clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork to complete all as specified & directed.

M&L preparation of new steel and iron based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint of approved tint over & including one coat of red oxide primer complete all as specified & directed.

M&L preparation of old or previously treated steel and iron based surface of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof coverings complete all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F 0.80mm thick mild steel, plain & black sheet as in wall cladding, steel gates and similar work; cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc. as required complete all as specified & directed.

M&L machine cut Kota slab flooring, 20mm to 25mm thick, laid over & including 20 mm thick screed bed in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises to a distance exceeding 500mtr complete all as specified & directed.

M&L coloured glazed designer ceramic tiles (1st quality), 450mm x 300mm x 7/8mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering/backing coat in cement mortar 1:4 complete all as specified & directed.

M&L coloured, non-skid, jointfree, ceramic tiles, 1st quality, 7 to 8 mm thick, square/rectangular, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & including 15mm thick screed bed or bedding layers in cement mortar 1:4, complete all as specified & directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified & directed

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars complete all as specified & directed. Notes for BOQ item No. 36.00 & 37.00: (i) Steel window shall comply with IS 1038-1983 &. Rolled steel sections for fabrication shall conforms to IS 7452-1990. (ii) Glazing, wire mesh & painting shall be measured & paid seperately however one shop coat primer is included in quoted rates.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staple etc. complete all as specified & directed.

S&F sheet glass 4mm thick, ordinary quality, glazing with oil putty in squares not exceeding 0.5 sqm in each pane fixed with oil putty or wooden beads including glazing pins/ spring clips wherever necessary etc. complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame), area not exceeding 1.5 sqm each and removing from site, complete all as specified & directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose type of soil complete all as specified & directed.

Removal of excavated soil to a distance exceeding 250 mtr but not exceeding 500 mtr and depositing where directed complete all as specified & directed.

Demolition of Plain cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including removal of debris to a distance exceeding 500 mtr complete all as specified & directed

M&L plain cement concrete(PCC) 1:2:4, type B-1, using 20 mm graded mechanically crushed stone aggregates as in flooring, padding etc. complete all as specified & directed.

M&L consolidated hardcore of broken stone or boulders, gauge not exceeding 63mm, deposited, spread and leveled in layers not exceeding 15cm thick each, watered and rammed to a true surface complete all as specified & directed

M&L plain cement concrete(PCC) 1:2:4, type B-1, using 20 mm graded mechanically crushed stone aggregates as in roof kerbs or mud stops, rounded or chamfered on edges including necessary formwork to complete all as specified & directed.

M&L factory made precast cement concrete, 1:2:4, type B-1, using 20mm graded mechanically crushed stone aggregate as in kerb stone of size 450mm x 300mm x 150mm with fair faces including weathering slightly rounded or chamfered angles of throating with necessary form work and including setting in cement mortar 1:4 complete all as specified & directed. Notes : (i) The kerb stone shall be laid/fixed on ground with its width i.e. 300mm. (ii) The quoted rates include for use of formwork (straight or curved).

M&L 60 mm thickness M-35 grade machine pressed precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, with grey cement and pigment, laid over & including 30 mm thick consolidated fine sand cushioning complete all as specified & directed.

M&L 80 mm thickness M-40 grade machine pressed precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, with grey cement and pigment, laid over & including 30 mm thick consolidated fine sand cushioning complete all as specified & directed.

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast articles complete all as specified & directed.

M&L Brick work with sub class B, burnt clay bricks of old size, designation 75, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:4 complete all as specified & directed.

M&L plain cement concrete (PCC) 1:3:6 type C-1 (using 20mm graded mechanically crushed stone aggregate) in surface channels or drains complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified & directed.

S&F mild steel work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified & directed

Removal of excavated soil to a distance not exceeding 50 mtr & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed.

M&L Sand cushioning to electric cable with a layer of dry fine sand 8cm thick before laying the cable and 15cm thick after laying the cable (punned down to 18cm thick after laying and stretching of cable ) complete all as specified & directed.

Supply and laying old size, common burnt clay, sub class 'B' bricks, designation 75, laid flat & dry for protection of electric cable in trenches, adjacent to each other, perpendicular to central axis of cable complete all as specified & directed.

Supply & laying un-reinforced precast concrete cable cover , Class HV type-1, flat, size 300mmx180mmx40mm, laid flat for protection of cable , adjacent to each other, perpendicular to central axis of cable complete all as specified & directed.

M&L precast cement concrete block masonry with solid blocks, exceeding 10cm in width concrete mix of PCC 1:3:6, type C-1, using 20 mm graded mechanically crushed stone aggregates, setting in cement mortar 1:4 including necessary formwork with fair finish flat surface complete all as specified & directed. Notes: (i) The rates include for the use of forms, moulds or machine moulds and setting the blocks, slabs, etc. complete including raking back the joints of the internal faces (at least 10 mm) for pointing as the work proceeds or finishing with neat flush joints. (ii) Precast cement concrete item shall be reinforced, where indicated/directed however Reinforcement shall be measured & paid separately.

Supply, laying, jointing, testing & commissioning of HT XLPE cable(heavy duty), 11000 volts (earthed), insulated, screened, sound compacted aluminium conductor, screening with extruded semi conducting layers, insulation screening with copper tape covers laid up with PVC (ST-2), extruded inner sheathed GI strip armoured PVC (ST-2) out sheathed, ISI marked with IS-7098 Part II upto date, cross sectional area 95 Sqmm, 3 core, laid in trenches or fixed along the wall/pole or passing through pipes/ducts etc. complete all as specified & directed. Notes: (i) Cable shall be of manufacturing date not earlier than Sep 2023. All the cable shall be embossed with year of manufacturing, meterage at every metre, in addition to its own standard markings as per IS i.e. Size, voltage etc. (ii) Excavation & earth work, sand cushioning, protection pipes, end termination joints & protection covers shall be measured and paid separately.

Supply, laying, jointing, testing & commissioning of LT cable, 1100 Volts grade, heavy duty, XLPE insulated, armoured electric power cable with aluminium conductor of cross sectional area 240 sqmm, 3.5 core conforming to IS- 7098 (Part I) laid in trenches or fixed along the wall/pole or passing through pipes/ducts etc, complete all as specified & directed.

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 120 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 95 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 70 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 50 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 35 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 25 sqmm, 3.5 core

Description all as per BOQ item No. 61.00 here-in-before but cross sectional area 10 sqmm, 2 core

M&L GI pipe 100mm bore , light grade, for cable protection as in road crossing under road/path, under floor/plinth protection, fixed to wall/pole with fixing arrangement with suitable size of MS clamps, nuts, bolts & washers complete all as specified & directed . Note: Wherever MS clamp etc. shall be provided, same shall be painted with two coats of synthetic enamel paint over & including one coat of redoxide primer.

Description all as per BOQ item No. 69.00 here-in-before but GI pipe 80mm bore.

Description all as per BOQ item No. 69.00 here-in-before but GI pipe 50mm bore.

Description all as per BOQ item No. 69.00 here-in-before but GI pipe 40mm bore.

S&F cable jointing kit for 11 KV earthed grade cable, outdoor type, end termination, cold shrinkable type joints with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95sqmm 3 core complete all as specified & directed.

S&F cable jointing kit for 11 KV earthed grade cable, straight through, cold shrinkable type joints with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95sqmm 3 core complete all as specified & directed.

M&L earthing complete with galvanized steel earth plate electrode 600mm X 600mm, 6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of earth plate not less than 1.5 mtr below ground level surrounded from all sides by 15cm thick packed layer of charcoal dust & common salt filled in alternate layers and electrode connected to GI earth lead strip 32mm x 6mm upto 7.5mtr long by means of bolts, nuts, check nuts and washers of galvanized iron and connection to earthing test point & earth dolly & watering pipe 1.5 mtr long light grade GI 20 mm bore including protection pipe upto 7.5 mtr long GI light grade 40mm bore, including wire mesh, funnel, lugs, salt, charcoal dust, excavation in soft/losse soil, returning filling & removal of surplus soil upto 50mtr, pit chamber shall be of PCC 1:3:6 type C-2 using 40 mm graded mechnically crushed stone aggregates and pit cover slab 40mm thick precast RCC 1:2:4 type B-1 using 20 mm graded mechnically crushed stone aggregates reinforced with 6mm dia MS round bars @ 150mm centre to centre both side including necessary form work complete all as shown in electrical plate No 3 of SSR part-I, including testing on completion at site complete all as specified & directed. Notes :- On testing if the desired earth resistance(i.e. less than 05 ohm) is not obtained, earthing will be re-done at no extra cost, till the desired earth resistance obtained. The chamber shall be constructed atleast 1.5 mtr away from the earth electrode.

M&L in replacement outdoor type HT feeder pillar box made of CRCA sheet 3.15 mm thick, CPRI tested and angle iron frame of size 40mm x 40mm x 6mm, dust and vermin proof with front and rear opening, including provision for 03 Nos. aluminum busbar size 40mm x 10mm fixed on HT bushing and having suitable provision for connecting cable upto 120 sqmm 3 core complete with required foundation work, including painting with one coat of red oxide paint and two coat of exterior weather proof paint and making cable connection with appropriate size cable glands complete all as specified & directed.

M&L repair/welding/bracing works required at site for unserviceable/broken/damaged LT Panel etc. Replacement of broken hinges if any. The size of repairable panel not exceed 2.0 mtr x 1.8 mtr x 0.6 mtr. The repairable panel are installed at various location under AF STN Dehradun. The repair work includes two coats of synthetic enamel paint complete all as specified & directed

M&L applying two coat of superior quality synthetic oil paint on all exposed surface and internal portion of LT distribution panels including after necessary surface preparation of old painted surface complete including marking stencil letter writing with highly fluorescent sheet best quality directly stick to panel as marking /identification of circuits/Area of supply, height between 15 mm to 20 mm group of letter not more than 15 letters in each incoming and outgoing MCCBs or distribution cables complete all as specified & directed.

S&F LED Solar Street light fitting 35/36 watt, minimum 5000 lumens, inbuit lithium battery solar panel, charge controller with dusk down sensor complete alongwith 9 mtr octagonal pole, made of hot Dip galvanised comfirming to IS 4759: 1996 or IS 2629:1985, top dia 70 mm & bottom dia 155 mm having wall thickness 3 mm thick with base plate 260mm x 16mm alongwith foundation bolts as per manufacturer specification complete all as specified & directed. Make:- Philips/Crompton/Wipro Note : Rates for Excavation & earth work in any type of soil and RCC foundation alongwith formwork as per the manufacturer recommendations is deemed to be included in the quoted rates.

S&F all-in-one solar street light fitting 20 watt, IP 65 Protection, system lumens 3000lm + or - 10%, 40 Wp high efficiency Monocrystalline silicon panel with LiFePO4 battery, high effciency battery with higher life of > 2000 cycles, full power upto 10 hours (at fully charged battery), automatic dusk to down feature, internal PIR sensor for motion detection. MPPT charge controller with 95% - 96% alongwith specially designed pole mounting bracket allows different tilt angles, lateral and pole top mounting complete all as specified directed. Make : Philips/Crompton/Wipro

S&F SMART connected solar Mini mast with minimum 68 watt system design with 4x17 watt integrated all-in-one solar street light with 12000 lumen total using 4x3000 lumen & lithium ferro phosphate battery, solar panel and charge built into the luminaire, pressure die cast aluminium for sturdiness and long life. Specially designed pole mounting bracket allows different tilt angles, with 9 mtr octagonal pole made of hot dip galvanized confirming to IS-4759:1996 or IS 2629:1985, top dia 90mm & bottom dia 175mm having wall thickness 4mm thick with base plate 260mm x 16mm alongwith foundation bolts as per manufacturer's specification, lateral and pole top mounting, sunstay with system efficiency of more than 175 lumen/watt complete all as specified & directed. Make : Philips/Crompton/Wipro Note : Rates for Excavation & earth work in any type of soil and RCC foundation alongwith formwork as per the manufacturer recommendations is deemed to be included in the quoted rates.

S&F electricity saving devices 230 volt PR based, movement detector with a build-switch off the light in a room or area when it is vacated and thus save energy. It can operate load upto 6 Amp and can operate 20 Sqm to 50 Sqm area complete all as specified & directed. Make : Philips/Crompton/Wipro

Supply, installation, testing & commissioning of LT Panel board indoor type made out of 2 mm CRCA Sheet, CPRI tested cubical type totally enclosed wheather dust and vermin proof with front and rear opening of 415 Volts 3 phase 4 wire 50 Hz having 4 pole aluminium bus bar capacity 400 Amps insulated with heat shrinkable sleeves RYB including internal wiring with copper conductor powder coated including connecting all in coming and out going cable feeders with necessary lugs ferrules etc . The panel should have angle iron support on the base all around including PCC foundation support , well finishing with cement mortar. Comprising of the following accessories as under complete all as specified & directed:- (a) Mains Incomming : (i) MCCB thermal magnetic 250 Amps 4 Pole 25 KA -02 No (01xSpare) (ii) Change over switch 250 Amps, 4 Pole -01 No (b) Outgoing : (i) MCCB 100 Amps 4 Pole 25 KA-04 Nos (ii) MCCB 63 Amps 4pole 16 KA- 02 Nos, (iii) MCCB 40 Amps 4pole 10 KA- 01 Nos. (iv) Multifunctional Amp meter, Volt meter, KW meter etc-01 No (v) RYB LED Indicating lamp - 01 Set

Supply, installation, testing & commissioning in replacement LT Panel board made out of 3.15 mm CRCA Sheet, outdoor type, CPRI tested cubical type totally enclosed wheather dust and vermin proof with front and rear opening of 415 Volts 3 phase 4 wire 50 Hz having 4 pole aluminium bus bar capacity 200 Amps insulated with heat shrinkable sleeves RYB including internal wiring with copper conductor powder coated including connecting all in coming and out going cable feeders with necessary lugs ferrules etc . The panel should have angle iron support on the base all around including PCC foundation support , well finishing with cement mortar. Comprising of the following accessories as under complete all as specified & directed:- (a) Mains Incomming : (i) MCCB 100 Amps with thermal based release 4 Pole 25 KA -01 No (b) Outgoing : (i) MCCB 63 Amps with thermal based release 4 Pole 16 KA-03 Nos (ii) Multifunctional Amp meter, Volt meter, KW meter etc-01 No (iii) RYB LED indicating lamp -01 set

Supply, installation, testing & commissioning of LT Panel board outdoor type made out of 3.15 mm CRCA Sheet CPRI tested cubical type totally enclosed wheather dust and vermin proof with front and rear opening of 415 Volts 3 phase 4 wire 50 Hz having 4 pole aluminium bus bar capacity 350 Amps insulated with heat shrinkable sleeves RYB including internal wiring with copper conductor powder coated including connecting all in coming and out going cable feeders with necessary lugs ferrules etc . The panel should have angle iron support on the base all around including PCC foundation support , well finishing with cement mortar. Comprising of the following switchgear and accessories are as under complete all as specified & directed:- (a) Mains Incomming : (i) MCCB 200 Amps with thermal based release 4 Pole 25 KA -01 No (b) Outgoing : (i) MCCB 100 Amps with thermal based release 4 Pole 16 KA-01 Nos (ii) MCCB 63 Amps with thermal based release 10 KA-01 No (iii) Multifunctional Amp meter, Volt meter, KW meter etc-01 No (iv) RYB LED indicating lamp -01 set

Supply, installation, testing & commissioning of LT Panel board outdoor type made out of 3.15 mm CRCA Sheet, CPRI typetested cubical type totally enclosed wheather dust and vermin proof with front and rear opening of 415 Volts 3 phase 4 wire 50 Hz having 4 pole aluminium bus bar capacity 100 Amps insulated with heat shrinkable sleeves RYB including internal wiring with copper conductor powder coated including connecting all in coming and out going cable feeders with necessary lugs ferrules etc . The panel should have angle iron support on the base all around including PCC foundation support , well finishing with cement mortar. Comprising of the following accessories as under complete all as specified & directed:- (a) Mains Incomming : (i) MCCB 63 Amps with thermal based release 4 Pole 16 KA -01 No (b) Outgoing : (i) MCB TPN 40 Amps 10 KA - 04 Nos (ii) MCB SPN 63 Amps - 05 Nos (iii) RYB LED indicating lamps - 01 set (iv) Multifunctional Amp meter, Volt meter, KW meter etc-01 Job

Supply, installation, testing & commissioning of LT Panel board outdoor type made out of 3.15 mm CRCA Sheet, CPRI type tested cubical type totally enclosed wheather dust and vermin proof with front and rear opening of 415 Volts 3 phase 4 wire 50 Hz having 4 pole aluminium bus bar capacity 100 Amps insulated with heat shrinkable sleeves RYB including internal wiring with copper conductor powder coated including connecting all in coming and out going cable feeders with necessary lugs ferrules etc . The panel should have angle iron support on the base all around including PCC foundation support , well finishing with cement mortar. Comprising of the following accessories as under complete all as specified & directed:- (a) Mains Incomming : (i) MCCB 63 Amps 4 Pole with thermal based release 25 KA -01 No (ii) Change over switch 63 Amps, 4 P-01 No (b) Outgoing : (i) MCCB 40 Amps with thermal based release 3 Pole 16 KA -02 No (ii) MCB TPN 16 Amps 10 KA - 1 Nos (iii) RYB LED indicating lamps at each out going - 01 set (iv) Multifunctional Amp meter, Volt meter, KW meter etc - 01 Job Notes : (i) Panel shall be mounted on brick work platform duly plastered and PCC copping work on top surface, height shall be 0.60 mtr above the GL and 0.40 mtr all around the FPB. The cost of any earthwork, PCC, brickwork etc. deemed to be included in quoted rates. (ii) All incoming and out going cables shall be connected with suitable size of cable luggs and cable galands etc. (iii) Layout diagram of LT Panel shall be produced by contractor for approval of Accepting Officer through GE before placing order to manufacturer and panel shall be brought at site as per approved drawing.

Supply, installation, testing & commissioning of outdoor type AMF panel 250 Amps suitable for 160 KVA generator, made of CRCA sheet 3.15 mm thickness CPRI approved along with contactors, relays, delay timer, indicating lamps, multifunctional meter along with foundation as per manufacturer's norms, 24 volts battery charger with frame of angle iron etc with the following specifications complete all as specified & directed (i) AMF relay, microprocessor monitoring and control system with LED Display and LED's for annunciation of parameters of control panel complete. (ii) Bus bar of aluminium strip of 250 Amps - 04 Nos for phase & neutral duly mounted on SMC/DMC insulators of suitable length. (iii) Contactor, 3 phase, 415 volt, AC 3 rating of capacity 250 Amp, for both main & DG supply. (iv) MCCB, 4 pole, 250 Amp, 35 KA rating with fixed thermal and magnetic setting having lcs = 100% lcu - for both main & DG supply. (v) Auxiliary contactors - 4 Nos. (vi) Multifunction meter for measure of Voltage, Current, Frequency, KWH, PF, KVRH and KVAH including provision of CT's of suitable capacity connected to outgoing 12 volt battery. (vii) SMPS battery charger suitable for charging feeder. (viii) Micro-processor control, self operated over current and earth fault relay with instantaneous setting including CT's of class 5P10 of 160/5Amp capacity connected on outgoing feeder. (ix) PVC insulated armoured, multicore, copper conductor cable for connection of DG set to AMF panel. (x) Control wiring PVC insulated, copper conductor of 1.5 Sqmm inside AMF panel. (xi) LED based indication lamps for DG supply and main supply. Note : Layout diagram of AMF Panel shall be produced by contractor for approval of Accepting Officer through GE before placing order to manufacturer and panel shall be brought at site as per approved drawing.

Supply, installation, testing & commissioning of 11/12 KV 3 way, Non-extensible 630 Amps, 21 KA, IP 54 Outdoor Type SF6 gas insulated 630 Amp copper busbar RMU comprising of three direct module cable entry and three manual load Break Switch as details below, robotically welded minimum 2.5 mm thick non magnetic non ferrite stainless steel tank filled with SF6 with IP class IP 67, leak rate less than 0.1 % and HT tank tested for internal Arc fault of 21 KA upto 03 second as per latest IEC 62271-200. The unit shall have front/side/rear cable entry of the switch gear, to ensure IP54 protection for full door covering of complete switchgear cable bushing shall be site replaceable type complete all as specified & directed (i) Load break switch module-03 No (ii) Manual operated 12 KV 630 Amp Load Break switch and earthing switch. (iii) Live Cable LED indicators through capacity voltage dividers mounted on the bushings. (iv) Earth fault passage indicator (v) Suitable site replaced bushings (vi) Mechanical ON/OFF/EARTH indication (vii) Cable boxes suitable for 1x3Cx300 sqmm XLPE cable and cable Termination protection. (viii) Cable door should be arc proof and interlocked with respective Earthing switches for safety of operator it should not be possible to open the cable door unless the earth is ON. Notes: The drawings in respect of RMU shall be approved by Accepting Officer through GE and as & when requested by contractor before placing order to manufacturer. RMU shall be tested by representative of Accepting Officer at factory premises before dispatch as & when requested by contractor. The testing and commissing after installation of the RMU shall be carried out in presence of Senior Electrical Inspector as & when requested by contractor.

S&F in replacement Air break switch gang operated, triple pole, for horizontal or vertical operation, mechanically operated, outdoor type, mounted on 9 insulators and steel frame with operating mechanism & operating rod of 25mm bore, medium grade GI pipe from ground level with & including locking arrangement & minumum 02 Nos. eye hook, 400 Amps current rating 11000 volts working pressure including making electrical connections to make it functional after testing complete all as specified & directed.

S&F HT lightning arresters 11 KV, expulsion type complete with all fittings, transmission class, discharge capacity 65 Kiloampere complete all as specified & directed.

M&L true vertical steel tubular, swaged welded pole conforming to IS-2713 part II , type 410 SP 31, 09 metre long complete with mild steel base plate of 6 mm thick of size 300mm X 300mm, finial taper plug, cap, bolts, nuts, washer and screws hole of required size and Nos. for fixing cross arms including painting externally with two coats of aluminium paint over & including one coat of zinc oxide primer for exposed surface and two coats of black bituminious paint for embeded portion in concrete as well as throughout internally including provision of white & blue colour strips with fluorescent paint upto 1.5 mtr height & nubmering of pole complete all as specified & directed.. Note:- Excavation, earth work and PCC shall be measured and paid separately.

S&F LED street light fitting 35 Watt 230 volt AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified & directed.

M&L street light bracket made out from GI Pipe 32 mm, light grade, 1 mtr long bent to shape including fixing clamp made out from MS Flats of size 25x5 mm complete with nuts and bolts and washers of suitable size duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed .

S&F PVC junction box (water proof) of size 250mm x 250mm x 160mm for street light poles with connector for connection incoming and outgoing cables including provn of 01 No MCB SP 06 Amp to control the pole light circuit including 04 x aluminium bus bars strips 150mm x 30mm x 3mm of size mounting on the insulator and MS brackets made out of 32mm x 4mm, flat iron clamps with suitable nut, bolts and washers including suitable size of double compression cable glands for incoming and outgoing cables complete all as specified & directed .

S&F PVC insulated copper wire 1.5 sqmm 3 core for street light fitting from juction box to fitting comple along with suitable clamps complete all as specified & directed

S&F Automatic street light switch using infrared Sensor based Nature Switch for automatic switching of street light. Nature switch operating should be based on Nature switch lux level required illuminare level for switching ON is < 30 Lux and for switching Off > 10 Lux. The sensor should also have part night opeation facility for 4,5,6....11 & 12 hours. The sensor alongwith suitable power contractors, Incoming outgoing MCBs should be enclosed in a pole/wall mountable enclosure made of rust proof, electric shock proof, termite proof and FR grade SMC juction box confirming to IP54. The circuit should be suitable to the three phase load of 6 KW with contactors (3 Nos) & incoming-outgoing MCBs (3 Nos each) rating of 20-25 Amps & circuit wiring of minimum 10 Sqmm complete all as specified & directed.

S&F in replacement of new generation, IP 65 LED post top of 25 Watt family, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluuminium landscape luminaire with high power LED's as light source, clear cover offers bright illumination for different applications complete all as specified & directed

S&F in replacement integrated all in one LED solar post top fixture 25 watt having 3000 lumens out put with the efficiency of 160 lumens/watt. Fixture must have inbuilt microwave senser, battery should be life 04 years, IP 65 protection, life class 25000 burnig hours complete all as specified & directed

M&L UL listed & CPRI tested maintenance free, low carbon copper coated earth rod of 2.00 mtr electrode having diameter of 14.2mm with copper coating thickness of 250 micron tested as per IEC 62561-2, (Internal earth rod is made of steel and outer surfance shall be copper coated) with 25 kg earth conductivity enhancing compround (IEC 62561-7), heavy duty earth chamber of dimension 308 x 308 x 211, load bering capacity 50000 Kg to ensure safety of earthing system alongwith PVC insulated copper conductor armoured cable single stranded of 10 Sqmm upto 7.5 mtr complete all as specified & directed. Make : OBO bettermen / Ennov /JMV

Supply, laying, connecting & testing of 100mm bore Ductile iron pipe with spigot and socketed end including required rubber gasket and tyton joint, centrifugally cast, Class LA in any length laid in trenches complete all as specified & directed

Supply, laying, connecting & testing of 80mm bore Ductile iron pipe with spigot and socketed end including required rubber gasket and tyton joint, centrifugally cast, Class LA in any length laid in trenches complete all as specified & directed. Note for BOQ item No. 101.00 & 102.00: Excavation & earthwork shall be measured & paid seperately.

M&L 80mm bore GI Pipe medium grade laid as in trench with all necessary fittings such as bend, elbow, socket, Tee, Union, Reducer socket etc. complete all as specified & directed

Description all as per BOQ item No. 103.00 here-in-before but 50mm bore GI Pipe

Description all as per BOQ item No. 103.00 here-in-before but 25mm bore GI Pipe. Note for BOQ item No. 103.00 to 105.00: Excavation & earthwork shall be measured & paid seperately.

S&F in replacement 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed confirming to IS 9338 complete all as specified & directed.

S&F 50mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed confirming to IS 9338 complete all as specified & directed.

S&F 80mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed confirming to IS 9338 complete all as specified & directed.

S&F sluice valve 80mm dia confirming to IS 14846 heavy duty with flanged end with brass spindle, sheet gasket 3mm thick, class 1.6 PN complete all as specified & directed

S&F sluice valve 100mm dia confirming to IS 14846 heavy duty with flanged end with brass spindle, sheet gasket 3mm thick, class 1.6 PN complete all as specified & directed

S&F sluice valve 150mm dia confirming to IS 14846 heavy duty with flanged end with brass spindle, sheet gasket 3mm thick, class 1.6 PN complete all as specified & directed

M&L cutting the existing GI pipe and inserting new GI pipe connection along with the required fittings at site for 100mm bore pipe complete all as specified & directed

M&L high power single head chemical dosing system single phase, Injection dosing system with PPM control mechanism complete, 230 Volt 50 Hz 40 SPM, 1/30 fractional horse power, pressure 5 Kg/Sqcm, Max output 6.5 Ltr/hour with lead tubing, connecting ferrule, check valve etc complete all as specified & directed. Make: ION Exchange / Toschon / Aquafit / Sathya Sai

M&L prepation tank of net capacity 170 ltrs FRP dosing tank dia 650 x net height 375 and conical 300 mm, gross height with stand 1000 mm consisting of water inlet line, outlet with Y stainer, drain, over flow, conical bottom of sludge deposition, pot hole with cover, level gauge and Service tank model No AQUA1006 of net capacity 100 Ltrs of FRP dosing tank top dia 540 mm x bottom dia 480 x height 575 mm consisting of water inlet line. dosing pump inlet arrnagement, drain overflow, level gauge, inspection port complete with Agitator 120 Watt 900 RPM single flange mounted motor with plastic shaft and impeller complete all as specified & directed. Make: ION Exchange / Toschon / Aquafit / Sathya Sai

S&F in replacement cast iron fittings for flanged pipe such as Bends, Tapers, Tee pieces (single & double branch) for size upto 100mm bore pipe and any angle/radius and straight connecting pieces complete all as specified & directed

For Credit Schedule refer tender documents. The amount of credit schedule shall be deducted from total quoted amount of BOQ to arrive contract sum.

KULWANT SINGH

RAMAPATI ENGINEERING SERVICES

Shikhar ji Enterprises

High Tech Metal India

BEHL AND COMPANY

BAL SINGH AND SONS