SPL REPAIR TO ROAD AT CERTAIN AREA AT LANCER LINE-II AND JOMI AT ARMY AREA JODHPUR UNDER GE (ARMY) NO. 01

Amount

Scarifying or picking gravelled macadam or bituminous macadam surfaces in area exc 400 sqm each and not exc 50 mm deep incl removing the unserviceable materials / debris outside the premises of MOD Land and disposal of the same complete all as specified and as directed by Engineer-in-charge

M&L for bituminous premix semi dense asphaltic concrete 40mm consolidated thickness with 5.50% binder content by weight of total mix using paving bitumen VG-40 grade, mixed in computerized hot mix plant, laying with mechanical paver, rolled and compacted to required camber or gradient using 8 to 12 ton power roller complete all as specified and as directed by Engineer-in-charge. Note:- (i) The mix design shall be got done from approved lab and got approved from GE before commencement of work. (ii) In the event of variation in the mix design in the percentage of binder content on minus side, the difference in quantity of binder content will be adjusted through supply only rate of Rs 48/- per kg for paving bitumen VG-40. However no plus adjustment shall be applicable if excess quantity of binder is used/approved in the execution of work under in this item

M&L for Laying and compacting 150 mm thick (compacted thickness) laid in two layers of 75 mm each)Wet Mix Macadam (WMM) grading as pe table 400-13 of MaRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 8-12 Tonne static weight and consolidating to required gradient and camber complete all as specified and as directed by Engineer-in-charge. The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013.

M&L for Preparing unsurfaced WMM surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 0. 7-1 kg/sqm on surface of WMM as specified in Table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as specified and directed by Engr-in-charge.

M&L for Premix bituminous macadam, binder content 4% by weight of total mix using Paving bitumen grade VG-40 penetration laid/rolled by mechanical paver and compacted to required gradient and camber by using 8-12 ton capacity mechanical power roller (consolidated thickness 75mm thick or less) complete all as specified and directed by Engr-in-charge.

M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed by Engr-in-charge.

M & L for preparing bituminous surfaces of road and marking 2.5mm thick Zebra crossing etc. and the like exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed by Engr-in-charge.

S&F ABS road colour Cat eyes having dual directions reflective panels (Both sides) of size 100 x 100 x 18-20mm with ABS body filled & fixed with epoxy adhessive as per manufacturer and / or fixing with 12 cm long mild steel pin on road complete with PMMA striplens with load capacity greater that 50 Kg with visibility 800 meters etc (Colour of reflective panels Amber/ Red/ White) complete all as specified and as directed incl taking out old unserviceable cat eye any size & and removing the same from site complete all as specified and directed by Engr-in-charge.

Supply and fix in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete all as specified and directed by Engr-in-charge.

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness and removing from site complete all as specified and directed by Engr-in-charge.

M&L for 100 mm thick Cement concrete type D - 2,1:4:8 (40 mm graded agg) as in sub base to floors incl well compacting & laid to levels complete all as specified and directed by Engr-in-charge.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour (red and yellow only), design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and directed by Engr-in-charge.

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening including excavation in trenches and removal wherever required complete all as specified and directed by Engr-in-charge.

M&L for two coat Synthetic enamel paint on concrete surface (kerb stone) Surfaces of any description over 10cm girth or width, not otherwise describedas complete all as specified and directed by Engr-in-charge.

M&L for repairs to pot holes any depth not exc 1 sqm each including sweeping free from dust and mud or water ,scoring sunken surfaces in roads etc cutting around edges to at least 30 mm in depth making good by applying tack coat with paving bituminous primer at 5 Kg / 10 sqm putting in premixed semidense asphaltaic concrete using 5.5% binder content by weight of total mix, well rammed and sealed well rammed (incl supply of premixed macadam , binder and chippings) depth of pot holes exceeding 30mm complete all as specified and directed by Engr-in-charge.

M&L for preparing the existing black top surface with wire brushes for removing caked mud etc scraping with brooms and finally fanning with cleaned surface with gunny bags to remove all loose dirt etc and M&L Applying evenly a tack coat of Cationic Bitumen Emulsion (RS-1) conforming to IS: 8887 at a rate of application of 0.2-0.3 kg/sqm on bituminous surface as specified in Table 500-5 of MaRTH specification for road and bridge works 2013, using mechanical sprayer after cleaning of existing surface complete all as specified and directed by Engr-in-charge.

M& L for providing bitumen premix Semi dense asphaltic concrete 30mm consolidated thickness with 5.50% binder (paving bitumen VG-40) by weight of total mix, mixed in computerized hot mix plant, laid, rolled and compacted to required gradient and camber with the help of mechanical paver and power roller 8 to 10 tonne capacity complete all as specified and directed by Engr-in-charge. Note :- (i) The mix design shall be got done from approved lab and got approved from GE before commencement of work. (ii) In the event of variation in the mix design in the percentage of binder content on minus side,the difference in quantity of of binder content will be adjusted through supply only rates of Rs 42/- per Kg for paving bitumen VG-30.However no plus adjustment shall be applicable if excess quantity of binder content is used/approved in the execution of work under this item.

S&F in repair for Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed by Engr-in-charge.

S&F in repair for 900mm dia reflective safety traffic mirror for road and side walk of stainless steel face, 0.90 mm thick large radius of curvature for minimum distance distrotation orange powdwr coated steel back and hood orange vinyl extrusion with 75 mm clamp brackets for pole mouting incl 50 mm dia 2mm thick SS pipe 2.4 to 3.0 mtr length top of pipe cover with round decorative type made of SS and including excavation & embedding in PCC 1:2:4 (400x400x650mm) type B1 complete all as specified and directed by Engr -in-charge.

S&F for Yellow and black plastic speed bum made up of ABS materials to highly reflective reflector moulded in EMMA materials welded with ABS base plate through Ultrasonic welding processes of size 350mm length and width of 263mm with working width of 250mm, height 53mm and weight appx 1200gms. complete all as specified and directed by Engr-in-charge.

M&L for 100mm thick red bajri/ Moorum spread,rolled and consolidated to gradient & camber required alongside paved roads as in berms incl necessary surface excavation, watering & rolling all as directed at site complete all as specified and directed by Engr -in-charge

OM BUILDERS (BID ID -3499112)

MAHARISHI GAUTAM CONSTRUCTIONS (BID ID -3499030)

New Vishvakarma Udhyog (BID ID -3505822)