PROVN OF GUARD ROOM AT CB RANGE, LADIES TOILET BLOCK AT FVT FWT AND STORAGE ACCN FOR STATION STORES AT OUTRAM LINE UNDER GE (ARMY) BARODA

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Removing excavated soil exc 250 m and n. exc. 500 m depositing where directed at level n exc1.5 mtr above the starting point.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, etc or for the shafts, well, cesspits, manholes, pier holes, etc n exc 10 Sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil.

All as per item No 3 above but depth exc. 1.5 m & n. exc 3.0m

M & L plain cement concrete as in foundations, filling and mass-concrete type D2 1:4:8 (40 mm graded stone aggregate) complete all as specified and as directed.

M & L for Used and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams; and similar work; rough finished surfaces of concrete flat etc. complete all as specified and as directed.

M&L for used and waste formwork to sides of pillars, posts, struts, piers, coumns and stanchions etc. Squires, rectangular etc. complete all as specified and as directed.

M&L for used and waste formwork to sides and soffits of roof Beam or lintel beam . Squires, rectangular etc. complete all as specified and as directed.

M&L for used and waste formwork to fin or facia or sides of concrete flat complete all as specified and as directed.

M&L for used and waste formwork to soffits of suspended slab such as roof slab , floor slab, landing and similar work complete all as specified and as directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe -500D complete all as specified and as directed.

All as per Item No 11 above but 5 mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as specified and as directed.

M&L for reinforced cement concrete work (Design mix)M-25 with using 20mm graded stoneaggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc.complete all as specified and as directed.

M&L for reinforced cement concrete work (Design mix)M-25 with using 20mm graded stoneaggregates as in beams,cantilievers, bressumers over 1.5 mtr, lintel Beam including chajja complete all as specified and as directed.

M&L for reinforced cement concrete work (Design mix)M-25 with using 20mm graded stoneaggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for reinforced cement concrete work (Design mix)M-25 with using 20mm graded stoneaggregates as in Roof Slab complete all as specified and as directed.

M&L for reinforced cement concrete work (Design mix)M-25 with using 20mm graded stoneaggregates as in Fin/Facia

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm in soft/loose soil.

Spreading and leveling of soil obtainedfrom excavation in floor in layers n exc. 25 cm thick including well ramming watering as required.

M&L for brick work with sub class "B" bricks old size brick straight or curved on plan exc 6m mean radius, built in CM 1 : 6 complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks built in CM (1:4) straight or curved on plan to any radius in half brick thick walls with old size bricks complete all as specified and as directed.

M&L 40 mm thick Damp proof course in cement concrete type Bo 1:2:4 to horizontal or vertical surfaces including necessary formwork using water proofing compound @ 3% by wt of cement.(WPC will be measured separately)

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m

M&L for rendering 10mm thick on fair faces of bricks surface or concrete surfaces with CM 1:4 surface even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of concrete surfaces on ceiling with CM 1:4 surface even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on brick on other than fair faces of bricks or concrete surfaces with CM 1:4 surface even & smooth without using extra cement complete all as specified and as directed.

M&L for groove to plastering to all RCC members internaly all as directed

Supply only integral water proofing compound.

M&L 75 mm thick cement concrete type C2 1:3:6 using 40mm graded stone aggregate in plinth protection for finished even and smooth without using extra cement including forming joints and filling with bituminous filler material complete all as specified and as directed.

M&l for hardcore of guage n. exc 63mm, deposited, spread & leveled in layers n exc. 15cm thick,watered & rammed to a true surface complete

M&L 75 mm thick Cement concrete type D2, 1:4:8 (40mm grade aggregate) as in sub base complete all as specified and as directed.

M&L for prepararion of new plastered surface of wall and applying two coats of cement base paint over a coat of cement base primer complete all as specified and as directed.

M&L for pre-pararion of new plsatered surface of wall and applying two coats of distemper over one coat of alkali resistant primer complete all as specified and as directed.

M & L applying 2 mm thick wall care putty on new surface of wall complete.

M & L preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrom primer complete.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or grith and apply two coats of synthetic enamel paint over a coat of pink primer complete

M&L for 165x60 mm pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, locks strike plates etc.. complete as specified and directed

M&L for 105x60 mm pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, locks strike plates etc.. complete as specified and directed

S&F 35 mm thick 2nd class HW plain, framed, factory made panelled shutters (two panels), with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), cleaned seasoned and chemically pressure treated.

S & F 35mm thick 2nd class hardwood Glazed and skeleton shutters, , open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars, any numbers and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. cla-use 8.20 (a); supplied and fitted to chowkats.

S&F steel window with side hung shutters including box type hinges with pressed steel handles, MS tower bolt 100mm long(2 Nos in each leaf) and steel peg stay complete with glazing bars dove-tailed or welded complete including one coat of shop coat of primer.

All as per item No 42 above as above item but without glazing bars

S&F Steel ventilator with top hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded complete

S&F Steel ventilator with top hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars dovetailed or welded complete

S & F mild steel bars conforming to Fe 290 Gde E-165 as in guard bars or similar works including welding etc complete all as specified.

S&F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane

S&F 4.00mm thick figured glass, pin head type and glazing with oil putty in square n exc 0.5 sqm in each pane

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete

S&F Mild Steel bands, straps, supports or holdfasts etc and similar small articles conforming to Fe 310-O or Fe 410-O complete

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required & directed by the Engr-in-Charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing.The door frame shall be tied to the wall using 75/100mm long MS screw as directed .

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 200mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Butt hinges, Medium weight, cold rolled mild steel, and fixed 100mm size complete

S & F 200mm size aluminium anodised, barrel tower bolt of extruded section.

S & F 150mm size aluminium anodised, barrel tower bolt of extruded section.

S & F 150mm aluminium alloy handles, fabricated type anodised

M&L for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor over all lenth of cover plate 150mm complete.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete incl screed bed or bedding layer of 15mm thick for laying floor finishes in CM 1:6 complete

M & L for machine cut kota stone slab 20 - 25mm thick in skirting, riser etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including rendering or bedding layer of mortar 10 mm thick for laying floor finishes with CM 1:4

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.06Sqm but n. exc 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM(1:6) complete all as specified

All as per item No 62 above but as in skirting including 10mm thick backing coat of tiles in CM(1:4) complete all as specified.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including lime concrete bedding complete all as specified.

S&F PTMT square grating 150mm size for trap in repairs complete

M&L for Vitreous china wash hand basin white flat back 550 x 400 mm with pedestal of standard size including chromium plated brass waste coupling, waste pipe, vulcanite plug with ring, pillar taps, PVC connection of suitable length, brackets and cutting for & pinning in ends of brackets etc complete and fixed.

M&L for Vitreous china urinals, half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plug with & including 60 mm long brass screw, fixing flush pipe, brass CP grating and union for discharge pipe, PVC telescopic waste pipe of suitable length etc complete

M&L for Steel water tubing, medium grade, galvanised with & including all tube fittings & fixed / consealed in walls and ceiling or laid in floors including testing complete of 15 mm bore complete

M&L for Steel water tubing, medium grade, galvanised with & including all tube fittings & fixed / consealed in walls and ceiling or laid in floors including testing complete of 20 mm bore

S & F Bib tap cast copper alloy with crutch or butterfly handle screwed down, fancy type chromium plated screwed for 15 MM bore iron pipe or brass, ferrule & fixed complete.

S & F Stop valve, cast copper alloy, chromium plated fancy type handle, screwed down, high pressure with push type handle screwed for 15mm bore iron pipe and fixed.

Rotational moulded polyethylene (HDPE) water storage tanks, double layer, ISI Marked (cylindrical vertical with closed top) capacity 1000 litres hoisted and placed in posiition on PCC platform complete all as specified & as shown on drawings

S & F for Towel rail 600 mm long with PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete.

S&F for Brass chromium plated fancy type soap dish holder, fixed in position complete.

S&F for 5.5 mm thick looking mirror size 600 x 450 mm with PVC frame of approved quality & make by GE fixed in position with rawl plug and screws of appropriate size complete.

S & F 125mm dia chromium plated shower rose with swivel joints including fixing to GI union complete

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with back fill to be measured) complete

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per squaremetre of surface complete

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete

S&F PVC valveless 10lts capacity syphonic action type flushing cistern low level, white with inlet, ball valve float and handle including brackets and 32 mm dia polyethylene waste pipe all as specified & directed

S&F PVC connection 600mm long of dia 15mm complete.

S & F cast (Spun cast) iron soil, waste and vent pipes, in any length with or without ears with cement joints, fixed to walls/floor etc. complete all as specified dia of pipe 75mm,(Height of Bldg up to 10m)

S & F cast (Spun cast) iron soil, waste and vent pipes, in any length with or without ears with cement joints, fixed to walls/ floos etc. complete all as specified dia of pipe 100mm.

S & F cast iron Bends (any radius), diminishing piecs or tapers (larger bore measured) dia 75mm bore of pipe with oval access door complete in repairs all as specified.

S&F Cast iron branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches, dia 75mm complete all as specified.

S&F cast iron branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches, dia 100mm complete all as specified.

S & F cast iron cowls 100mm dia complete all as specified

S&F 20 mm thick granite Stone for partion wall including necessary cutting work to vertical surfaces complete all as directed.

S&F 20 mm thick green granite Stone for window cill including necessary screed bed and match to pigment including rubbish and polishing and half round the edge all as directed.

M & L for 10 mm thick cement plaster (1:3) in CM with using water proofing compound @ 3% by weight of cement as per manufacturer's instructions shall be applied on padding concrete when concrete is still green complete all as specified and directed by Engr-in-charge. (WPC will be measured separately).

M & L for applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 sq metre (Paving bitumin).

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M & L for cement concrete 100 mm thick type B-1 1:2:4 (20mm graded stone aggrete) as in approach path laid in alternate pannels used waste of form work/screed and to dividing the area in panel, finished even and smooth all as directed by Engineer in charge.

M & L for cement concrete bed to drain pipes in PCC 1:4:8, type D2 (using 40mm graded stone aggregate), for 150mm dia drain pipe including packing under and haunching against the sides of pipes with concrete after they are laid and tested complete all as specified and directed.

M & L for reinforced concrete pipe of 150mm bore of pipe, class NP-2, laid and jointed in cement mortar (1:1) complete with collars complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 using 20 mm graded aggregate as in benching to surface channels for manholes or drains etc, including finishing top of benching even and smooth using extra cement and including necessary formwork, complete all as specified and directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M & L for rendering 10 mm thick other than fair faces of brick work or concrete suraces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for precast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in manhole cover with plain fair surface including chamfers, weatherings, throatings, necessary form work and set in CM (1:6), placed in position complete all as specified and directed.

M & L for PCC 1:2:4, Type B-0 using 12.50mm graded stone aggregate as in coping, including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M & L for mild Steel TMT Bar 6 to 8 mm dia as in reinforcement, cut to length, bent to shape required, including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for cutting into existing MH for connecting new sewer line of dia 150mm including making good to existing MHS and channels etc all as specified in SSR.

Removing of surplus soil to a distance n exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point in soils complete all as specified and directed.

M&L 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded aggregate)

M&L for Glazed ceramic coloured walls tiles in vertical surfaces 450X300X 7mm, 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles.

M&L Rendering in two layer on fair faces of brick work or concrete surfaces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 smooth without using extra cement (WPC will be measured separately)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall as backing coat in cement mortar 1:6 for finished even and fair (without using extra cement)

Rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 for finished even and smooth withou using extra cement

S&F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

S&F 500 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F Ball brass valves, for 20 mm bore of pipe high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed

Supply and fix PVC connection 15 mm size with PTMT nuts of length 450 mm long.

S&F grating square 150 mm size of PTMT (Minimum weight 100 gms)

S&F 100mm bore sand cast iron soil, waste, vent pipes in any length with or without ears with cement joints, fixed to walls

S & F 100mm CI vent cowl

S & F 100mm bore branch pieces, single (equal or ;unequal) ordinary or inverted (spigot or socket type) or with parallel branches with access door all as directed

M&L preparing new plastered surfaces of wall and applying three coats of white wash on wall

M&L concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC conduit, medium grade minimum 20mm dia ISI marked and conduit accessories concealed in wall etc with sunken type pressed steel/welded MS terminal boxes made out of 1.2 mm MS sheet, 3mm thick laminated sheath top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisining of 1.5 sqmm PVC insulated unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly for One light/fan/bell point controlled by one switch 6 Amp one way

One light/fan/bell point controlled by one switch 6 Amp one way

One 3 pin switch socket combination 6 amp on the independent board.

One 3 pin switch socket combination on same board with other switches.

One exhaust fan point controlled by one switch 6 Amp one way

All as described as peritem No 120 above but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed FRLS cable 1100 volt grade and 1.5 sqmm PVC insulated and unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

All same as per item No.120 above but with 4 sqmm PVC insulated unsheathed multistranded copper FRLS grade cable with one run of 4 sqmm PVC insulated copper cable as earth continuity for power socket on independent board.

S/Fix MCB DB factory made IP 42protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed of following sizes:-

SPN 08 way

SPN 04 way

S&F MCBs 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB (DB will be measured and paid separately under respective items of sch A):-

MCB SPN 6 to 40 Amps.

MCB SP 6 to 40 Amps

M&L switch piano flush type single pole, one way 6 Amp .

M&L switch socket combination 5 pin 6 amp.

M&L Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal.

S/fix fan regulator electronic type 100Watt 20V-50Hz as directed by Engr-incharge

S/fix ceiling rose 65x17mm three terminals .

S&F ceiling rose surface backlite 3 terminals 65X50mm 230V including PVC Box of size 3"X3" round type.

S& F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting along with 09watt LED Lamp of make : Philips/Bajaj/Wipro

Supply and fixing ceiling fan 1200 mm sweep BEE 5 star rated including fixing of down rod and connection complete with & including provision of flexible three core PVC insulated multi-stranded copper conductor cable of size 0.50 sq mm from ceiling rose/connector to fan complete all as specified and directed. Make : Crompton Greaves or equivalent in Bajaj/Orient/Usha

Supply, Fixing, Testing and commissioning of 4' LED not less than 1X18W LED Batten with LED tube not less than 18 watt. Similar to Batten cat Part No.REGALBATTEN8UPTO1X22wSSBSWH and LED tube light cat part No.CRYSTAL1213T8DSTL18WLED865SGLASS of Make- Havells or equivalent in Make: Philips/Wipro/CG

S&F 18 W LED tubelight fitting of 4 ft with lamp, Endura linear LED Wall mounted LED batten,exruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 189W LED 6K with complete fitting.make: Havells cat no. LHEXBLP7UN1W018or equvalent to Bajaj, /philips/wipro

Supply, Fixing, Testing & Commsioning of IP65 integral LED Bulk Head luminaire. Power Consumption should not exceed 10W (Including Driver Loss). Similar to cat Part No. RUGBYNEONFT10WLED760SSYMBOPC of Make- Havells or equivalent in Make: Philips/Wipro/CG

S & F wall security light LED type 25W complete all as directed and specified by Engr-In-Charge. Make- Havells, Model-ENDURAPEARLSL25WLED757SASYTOPC or equivalent in Phillips/Wipro/CG.

M&L for 25 mm bore light grade GI pipe fixed as bracket, on wall any type, not less than 1.2 m long and bent to shape as required complete with sutiable clamp made out of 25x4mm Flat Iron duly fixed 12mm dia nuts, bolts, washers etc.suitable for bdlg wall/ pole complete all as specified and directed by Engineer-in-Charge.

M&L earthing complete with galvanized steel earth plate electrode 600mmX600mmX6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and connected to and including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES schedule Part-I, and testing on completion including necessary excavation and earth work in any type of soil, PCC(1:3:6) type C1 chamber, CI Cover with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe15mm dia, light grade 7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

M&L for sand cushoning, to cable with river sand and punning to provide required cover for UG cables completed all as specified and directed. Note: Punned thickness shall be measured.

M&L brick protection cover to electric cable with class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm completed all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 10 sq mm 2 core completed all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 2 core

M&L for galvanized steel tubing light Grade of 25 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

S & F wall security light LED type not less than 20W . The Luminaire connecting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete with GI pipe suitable bend 1.2 mtr long and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. Make- Havells, Model-ENDURACITYLITEPLATSL20W LED 757SASYBOPC or equivalent in Phillips/Wipro/CG.

Supply, fixing, testing & commissioning of Iron body exhaust fan 300 mm sweep 1400 RPM with minimum airflow/air delivery 1710 Cmh, totally enclosed heavy duty motor, die cast aluminium rotor mounted on double ball bearing, IP-55, polarity-4, 230 Volt AC supply (single phase), rated power input not more that 90watt, with louvers fixed outside bldg for auto opening and closiing and connecting up including provison of PVC insulated overall PVC sheathed copper conductor cable from ceiling rose to fan. Make : CG/Bajaj/Havells or equivalent. Similar to Crompton Greaves model No EXHD300-4-1

Supply and fix water cooler electric driven (single phase),fully stainless steel body having approx storage capacity 80 Ltrs with (Non CFC refrigerant), Make- Usha cat Part No SS-4080 euivalent of Voltas, Zenith, Blue Star and nominal cooling capacity of 40 Litres per hour.

Supply and Fix Desert cooler electric driven Single phase Make 230 Volts, 50Hz supply, including motor, pump, honey comb pads and all connected accessories complete, Make-Voltas model No. VND-70 MH, Symphony, Kenstar.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 25 mm bore of pipe complete all as specified.

Supply and laying in trenches/wall/roof of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 20 mm bore of pipe complete all as specified.

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

S&F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 40 to 50 mm dia

M&L brick masonary valve pit of size 750mm X 750mm X 750mm (internal dimension) complete with MS angle iron frame work (Angle Iron size 40mm X 40mm X 6mm) & 3mm MS sheet top cover openable through hinges including necessary locking arrangement, rendering complete and painting with two coat of black bituminous paint over a one coat red oxide primer all as specified and shown on drawing.

Supply, Fixing, Testing & Commisioning of 2' 10W Mirror LED Batten with system lumen output of 1000 lumens. System Efficacy should be > 85lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Housing of luminaire should made of die cast alumunium & mounting on two PVC square boxes of size not less than 75mm X 75mm complete including connecting fitting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete all as specified & directed. Make- Havells, Model-ENDURALINEARNEOBS1W LED 830SPCWH or equivalent in Wipro/Philips

S & F wall security light LED type 20W The Luminaire Should have Cool Daylight Color temp of 4000K & CRI>70.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Housing of luminaire should made of die cast alumunium connecting fitting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete with GI bend 1.2 mtr and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. Make- Havells, Model-ENDURACITYLITEPLATSL20W LED 757SASYBOPC or equivalent in Phillips/Wipro/CG.

Supply, fixing, testing & commissioning of Exhaust fan 225 mm sweep, aluminum rust proof body & blades, with louvers for protection from birds, 230 Volt AC supply, rated power input not more that 45watt, with louvers fixed outside bldg for auto opening and closing connecting up including provison of cable from ceiling rose to fan. Make : CG/Bajaj/Havells or equivalent. Similar to Crompton Greaves model No Trans Air 9"

Supply and laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVCtape armouredwith galvanised steel wire or tape and overall PVC sheathed 6sq. mm 2 Core nominal cross section in service connections .

M&L for galvanized steel tubing light Grade of 40 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

M&L cement concrete type C1 1:3:6 using 20mm graded stone aggregate in steel door frame hollow filling complete all as specified and as directed.

RAJENDRASINH B THAKOR

Shree Vaishno Enterprises