Establishment of Integrated Bee keeping Development Centre (IBDC) at Sidhpur in Tehsil Dharampur District Mandi (HP)

Amount

Cutting in earth work and disposal of excavated earth upto all leads and lifts complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Fiilling in earth within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work, blasting work, chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed in all leads including lifts and soring/strutting timbering and dewatering where ever required as per thr direction and to the entire satisfaction of the Engineer-in-charge.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu- reinforcement concrete and plain concrete work in:-

Foundation footing bases of columns etc and mass concrete complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like, Floors etc. up to any thickness complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Vertical surfaces such as wall (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Beam, cantilever, girders and lintels, Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns, pillars, post and struts, Square, rectangular or polygonal in plan complete within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work of ordinary timber plankings so as to give a rough finish including centring, shuttering, strutting & propping etc. height of propping & centring below supporting floor to ceilling not exceeding 4 mts. And removal of the same for insitu-reinforced concrete and plain concrete work in :

Arches beyond 6.00 mtrs span as per direction and to the entire satisfaction of Engineer-in-charge.

Providing and laying cement concrete 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40mm nominal size)curing complete excluding cost of form work in foundation and plinth as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size ) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying cement concrete 1:3:6 (1 cement: 3 sand: 6 graded crushed stone agg. 40mm nominal size) and curing complete excluding cost of form work in:- Foundation and plinth upto all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work in Suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumers and cantilever upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge

Providing & Laying cement concrete work 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation footing bases of columns etc and mass concrete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Walls any thickness but not less than 0.1m thickness including attached pillaster buttresses, plinth and string courses from top of foundation upto two level all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumers and cantilever upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Column, pillar, posts and struts upto floor two level as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Lintels, beams, girders, bressumers and cantilevers upto floor two level within all lead and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

Arches upto floor two level in all leads and lifts as per direction and to the entiresatisfaction of Engineer-in-charge.

Providing and laying no fine cement concrete 1:6 (1 Cement : 6 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in cement mortar 1:6 as per direction and to the entire satisfaction of Engineer-in-Charge.

Random rubble masonry/Polygonal rubble masornry ( uncoursed/ brought to courses) with hard stone of approved quality in foundation and plinth I/c levelling up with cement conrete 1:6:12 (1cement:6 sand :12 graded stone aggregate 20 mm nominal size ) at plinth level in cement motar 1:6 ( 1cement:6 sand)including curing complete. As per direction and to the antire satiafaction of the Engineer-in- charge in all lead and lifts.

Providing mild steel / Tor steel reinforcement for RCC work including bending binding and placing in position complete upto all floor level within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Brick work using common burunt clay building bricks in foundation anf plinthl in cement mortor 1:4 (1 cement : 4 sand) (2nd class brick) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Half brick masonry in common burnt clay 2nd class building bricks in superstructure above plinth level upto floor two level in cement mortar1:4 (1 cement :4 sand) as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Providing and laying interlocking paver block 60mm thick in grey cement and under layer of sand 0.125 mtrs or 125mm thick average complete as per direction and to the entire satisfaction of Engineer-in-Charge upto all lead and lifts.

Stone soling/boulder filling dry hand packed in under floor within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (1st class Teak wood) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (1st class Teak wood) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing 40x3 mm iron hold fast 40 cm long including Fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished mild steel tower volts (Barrel type) with screws etc. within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished mild steel sliding door bolt with nuts and screws etc. within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished mild steel handles with necessary screws. complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing & fixing bright finished mild steel Hooks and Eyes 150 mm with screws etc. within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 100 mm bright finished mild steel floor door stopper with rubber cushion screw etc. to suit shutter thickness complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and laying Duro stone vetrified tiles(300x300x10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:4 (1 cement: 4 sand) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

20 mm thick cement plaster with cement mortar 1:4(1 cement; 4 sand) in single coat on rough side of brick/concrete/stone walls for interior plastering all heights including arises, internal rounded angles chamfers and/ or rounded angles in all girth and finished even and smooth i) Upto all floor levels

6mm cement plaster to ceiling in cement mortar 1:4 ( 1Cement :4 Sand) within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement :3 sand) and curing complete in all lead and lifts as per direction and to the entire satisfaction of the Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete .

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Painting two coat (excluding Priming coat ) on new steel and other metal surface with enamal paint brushing to give an even shade I/c cleaning of all dirt dust and other foreign matter with silver paint as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lifts.

Steel work welded in built up section, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paintin grating, framed guard bars ladders, railing brackets and similar works as per direction of Engineer-in-Charge upto all lead and lift.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing white vitreous China pedestal type water closet (European type) with seat and lid, 10 liter low level white vitreous china flushing cistern & C.P. flush bend and fittings & C.I. brackets, 40mm flush bend, overflow arrangementwith special of standard make and mosquito proof coupling of approved municipal design complete i/c painting of fittings and brackets cutting holes in walls and making good wherever required. (Jaquar Make EWC one piece LYS-WHT)

Providing and fixing C.P. brass pillar cock of Jaquar Make Fonte Type within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings. Flat back 630x450mm Asian paint make with pedestal within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outletconnection, 15mm nominal bore ball valve and mosquito proof PVC cover with lockingarrangement including hoisting up to all heights above ground level :-1000 litres net capacity tank Syntax Make within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing CP mild steel towel rail complete with CP mild steel brackets fixed to wooden plug with CP mild steel screws 750 mm x 20 mm within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 600 mm x 200 mm glass shelf with C.P. mild steel bracket and guard rail complete, fixed to wooden plugs with C.P. mild steel screws within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing to wall, ceiling & floor, galvanised mild steel tube (Heavy Class), tube fittings & clamps i/c making good wall, ceiling and floor within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

20mm dia Nominal Bore TATA Make

15mm dia Nominal Bore TATA Make

Providing and fixing liquid soap container with C.P. mild Steel lid and brackets fixed to wooden plugs with C.P. mild steel screws :- Plastic container within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and Fixing 100 mm dia cast iron plated grating of superior quality for floor, gully or Nahni trap within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing 200 mm wide CI rungs with channel or ribed non slip surface including fixing in man hole with 200x100mm Cement Concrete 1:3:6 ( one cement :3 Sand : 6 Graded crushed stone agg.20mm nominal size)

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. 75mm Nominal bore within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. 110mm Nominal bore within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing C.P. mild steel angle valve 15mm without Nuts and pipe within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and fixing C.P. mild steel Soap dish with C.P. Mild steel brackets fixed to wooden plugs with C.P. mild steel screws within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Supplying and fixing cast iron cover with frame for man holes for frame of internal dimension 500mm dia the weight of cover should not be less than 23kg

Providing and fixing precast concrete manhole cover and frame, conforming to IS 12692-2002, 560mm dia complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Laying, jointing & testing of G.I pipe of following dia (light class) for outlets pipe & scour pipes etc. in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge. (Labour rate)

150 mm dia

100 mm dia

Providing and fixing double flanged Cast Iron sluice valve of following dia of Kirloskar/Leader make conforming to IS:14846/2000 with up to date amendment as per Class PN-1 to withstand in normal seat pressure including welding with M.S. flanges table as per IS 6392-1971 including carriage in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

150mm Dia

100mm Dia

Providing and fixing Manhole cover of size 60x60 cm made of angle iron frame size 40x40x5mm thick covered with M.S. sheet 2.00mm thick and welded with angle iron frame 35x35x3mm thick including hings, handles, 8 Nos hold fast and locking arrangement along with lock and key of standred make primer two coat with redoxide paint complete and manhole cover fixed in storage tank/intake with cement concrete 1:1.5:3, nut & bolt and dismentalling of RCC work complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Provision for structural design and drawing (after acertaining the safe bearing capapcity of the soil at site) the architecture drawing of all the buildings and all other components. The structural design & drawing for all the structures duly vetted from PEC Chandigarh/NIT Hamirpur shall be submitted by the contractor for approval of the Department before start of work.

Providing and fixing of PVC pipe of working pressure of 4.5 KG with iron brackets 40X3mm size with necessary screws, washers and adhesive etc. where required including making necessary connection with rain water pipe complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Providing and installation of mechinacal filter for rain water harvesting structure complete within all leads and lifts as per direction and to the entire satisfaction of the Engineer in Charge.

Electrical

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group "C"

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & Fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules (140mmx78mmx50mm)

6 modules (205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

2 x 4.00 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch.

6 pin,15/16 Amps Modular socket outlet.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

TV. Socket outlet, modular.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

Telephone socket outlet, Modular.

Supplying and Fixing ceiling rose on the existing junction box / wooden block including connections etc. as required.

Supplying and Fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-

Double door-12 way

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amps. Cat-A.

Supplying and Fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450 mm & cross-sectional area (25.4 mm x 4.75 mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530 mm x 450 mm x 150 mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and Fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.

100 Amp. Category-A

200 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required.

Single pole & neutral. Cat-B.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35 mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required.

Supplying and errection of 40/50/63 Amp rating, 10 KA breaking capacity 240 Volts, C-curves minituature circuit breaker of following poles in the existing MCB DB complete with connections as required.

Double pole Cat-B.

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps. Cat-B.

Supplying and Fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Supplying and Fixing of lightening conductor finial, made of 25 mm dia 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate incuding holes etc completeas required.

Supplying and fixing of copper tape 20mmx3mm thick on parapet or surface of wall for lightening conductor as required (for vertical run).

Supplying and fixing of copper tape 20mmx3mm thick on parapet or surface of wall for lightening conductor as required (for horizontall run).

Providing and Fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XPLE power cable, working voltage 1100 volts grade direct in ground to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the armoured cable 4 Sq.mm (twin core) for yard light.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and Fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required.

25 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and Fixing phenolic laminated sheet cover on the fan box and earthing etc. as required.

Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required.

Exhaust Fan, Light duty, (Domestic) 225 mm sweep

Providing and Fixing of 1x36 watt-LED (category-A) surface mounting fixture Syska/Havells complete in all respect in all leads and lifts.

Providing and Fixing 6 watt recessed down lights eound shape for false ceiling complete in all respect in all leads and lifts.

Supplying and fixing of fancy wall bracket containg thread type LED lamp holder (s) of sizes and shapes complete with all accessories but excluding CFL lamp including making connections, testing etc. as required fixed type wall bracket 150mm dia, single lamp (Category-A). complete in all respect in all leads and lifts.

Providing, installation, testing and commissioning of tube fitting 1x20W LED complete in all respect in all leads and lifts.

Providing and fixing mirror light 60 cms long 6 watt LED fixture complete in all respect in all leads and lifts.

Supplying and Fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:-

Providing and fixing 9 watt LED bulbs complete in all respect in all leads and lifts.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and Fixing bakelite batten/angle holder including connections etc. as required.

Supplying and Fixing of integral CFL Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required.

Gate post top lantern - CFL 26 watt.

Providing and fixing of integral LED boundary wall lights fixed over GI pipe polls 1.2 mtrs height 50 mm dia, 9 watt LED lamp with 200 mm dia globe made of acrylic sheet complete in all respect in all leads and lifts.

Supplying and fixing stepped type modular fan regulator on the existing modulat box including making connections etc. as required complete in all respect in all leads and lifts.

Supplying and fixing 12 unit intercome exchange with phone sets and wiring complete in all respect in all leads and lifts.

Supplying and fixing of split type air conditioner 2 Tonne capacity Blue Star/LG/ Onida/WhirlpoolLloyd/Smasung make having two star features auto clean filter four way swing all copper pipes including making provision of draining of back moisture water through GI pipe 20mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete in all respect in all leads and lifts.

Furniture:- Providing and fixing Office Table of Godrej/Durian/Zuari make ,size shall be 1500 Width mm x 750 Depth mm x 750 Height mm . The table top shall be made of pre- laminated particle board with 18 mm thick and 15 mm thick understructure covered with PVC lipping .There shall be locking provided for top drawers only , attractive black colour handles for all drawers plus only one colour is available beech. It shall have one drawer (RHS ) & HDU attachment on one side & 3 drawer unit on the other side ( LHS of user )

Providing and fixing Office Chair of Godrej/Durian/Zuari make ,The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. the dimensions of back shall be 49.5cm. (W) X 69.5cm. (H) and of seat shall be 49.5cm. (W) X 43.0cm. (D). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be made of black-integraL skin polyurethane with 50-70 Shore Hardness and reinforced with M.S. insert. The armrests shall be scratch and weather resistant. The armrests shall be fitted to the seat with seat armrest connecting bracket made of 0.3 ±0.022cm. thk.HR steel. The centre pivot mechanism shall be designed with 360° revolving type, 17 ±2°maximum tilt on pivot at center, Tilt tension adjustment, Upright position locking. The pneumatic height adjustment shall has an adjustment stroke of 12.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be injection moulded in black Polypropylene with metal insert and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm. pitch-centre dia. (76.3±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.4 to max 55.4cm, Height - min100.9 to max 122.9cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Providing and fixing visiting Chair of Godrej/Durian/Zuari The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 47.0(H) cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density= 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. The tubular armrest supports should hold together the seat and back. The tubular frame shall be cantilever type & made of 0 2.54±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair shall be Seat Height - 43.0cm, Height - 80.5cm, Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-61.0 cm.

Providing and fixing visiting benches of Godrej/Durian/Zuari The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The powder coated(DFT 50+/-10 microns) welded with M.S. structure is made from 5.08+/-0.03 x 5.08+/-0.03 x 0.16 x 0.0128. The 0.315+/-0.008cm thk HR steel plate is welded to beam for fixing seat and back frame. The powder coated(DFT 50+/-10 microns) welded leg M.S. structure is made from The powder coated(DFT 50+/-10 microns) welded leg M.S. structure is made up of 5.08+/-0.03 x 5.08+/-0.03 x 0.16 x 0.0128 and 5.08+/-0.03 x 2.45+/-0.03 x 0.16+/- 0.0128 cm.

Providing and fixing Executive table of Godrej/Durian/Zuari size shall be 1800 Width mm x 900 Depth mm x 725 Height mm.The Top shall be 25 mm thick pre-laminated board with 2 mm thick matching lipping stiffener provided under the top to give addition strength(1.6 mm thick MS).The Understructure shall be having pedestal of combination of processed wood (PLB) and mild steel (MS).There shall be 2 box drawers plus 1 filling drawer combination for both pedestals the pedestal shell shall be 0.8 mm thick MS plus the drawer tray, separator and pedestal bottom cover shall be 0.6 mm thick MS. Drawers mounted on Double extension steel telescopic ball slides to gives full access to drawer. ‘Separators’ (0.6 mm thk.) provided in box drawers to compartmentalize space to suit individual requirements. There shall be sleek handles for easy grip , glide screws for leveling and also independent locking arrangement for each pedestal. The Modesty shall be of MS panel (1.0 mm thick) recessed inside for more leg room.Panel is styled with cutouts (windows) to give it a trendy and up market look.

Providing and fixing Executive chair of Godrej/Durian/Zuari The seat shall be made of injection molded plastic outer and inner. Plastic inner shall be upholstered with fabric and moulded polyurethane foam of density 67+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The cushioned back shall be made of PU foam with molded MSERW oblong Tube of size 3.5+/-0.03cm x 1.5+/-0.02cm x 0.2+/-0.016cm. It shall be upholstered with fabric. The dimensions of seat shall be- 46.0cm(W) x 48.0cm(D) and of back shall be 45.8cm(W) x 62.8cm(D). The armrest top shall be moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of dia 3.81+/-0.03cm x 0.2+/-0.01 cm thick MSERW tube. Armrest height adjustable upto 6.5+/-0.5cm in 5 steps.. The mechanism of the chair shall have following features : 360⁰ revolving type, Active Bio-synchro mechanism, Tilt tension adjustment, 5-position tilt limiter giving option of variable tilt angle to the chair. Seat/Back tilting ratio of 1:2. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0+/-0.5cm. Back frame shall be connected to the Up/Down mechanism housed in plastic T spine. it can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. The pedestal shall be injection moulded in black 33% GF Nylon66. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 66.1+/- 0.5 cm pitch-centre-dia (76.1 +/- 1.0 cm with castors). The twin wheel castors shall be made of PP. Overall dimensions of Chair shall be, Width of Chair - 76.1cm, Depth of Chair - 76.1 cm as measured from pedestal below. Height from ground - min 99.2 to max 116.7cm. Seat height - min 43.6 to max 53.6cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Providing and fixing of 7 seater sofa set of Godrej/ Zuari/ durian make of following specifications- Upholstery • Material : Leatherite • Thickness : 1 mm Frame : • Material : Combination of plywood and pine Wood • Plywood thickness : 12 mm (moisture resistance and termite free) • Pinewood cross section ( without knots) - 22x64 mm - 34x64 mm - 16x35 mm Seat : • Material : Slab stock foam • Density : Base 28 kg/m3 and super soft 32 kg/m3 at top Back : • Material : Slab stock foam • Density : Super soft 32 kg/m3 with a layer of siliconized conjugated polyster fiber of 200 gsm Webbing • S spring of dia. 3.8 mm mounted on seat structure using plastic spring mounting clip. Legs : PVC Side Table -2 No. - Top Material - MDF (Medium Density Fiber) Board Frame Material & Legs Material - Rubber Wood Size - 45cmW x 45cmH x 53.1cmD

Providing and fixing of Centre table of Godrej/ Zuari/ durian make Centre table 4x2feet,Table Top Material - MDF (Medium Density Fiber) Board Frame Material & Legs Material - Rubber Wood Size - 120cmW x 37.8cmH x 60cmD

Providing and fixing of steel almirah of Godrej/ Zuari/ durian .

Providing and fixing of office reck of Godrej/ Zuari/ durian .

M/S NDN Constructions

Unipro Techno Infrastructure Pvt Ltd