SPL REPAIR TO BLDG NO T-117, REWIRING OF JCO MESS,

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in hard dense soil complete all as specified & directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard dense soil complete all as specified & directed.

M&L PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundations, mass filling , sub base and the like all as specified.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, ending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Dismantling wall and ceiling board or insulation boards/ slabs/ blankets, any thickness, including cover fillets.

S&F 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber rame work as in wall complete, all as specified and directed by Engr-in-Charge

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber rame work complete, all as specified and directed by Engr-in-Charge

Dismantling timber scantlings fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section in unframed work.

M & L 2nd class softwood Plain fillets square,rectangular or triangular in section, clean sawn, secured with nails or brads exceeding 13 sqcm but n.exc 25 sqcm specified and directed.

S&F in repair 2n class soft wood in moulding as in cornices, picture rails n exc 6 sqcm in sectional area complete all as specified.

M&L second class wood designer Plain fillets square,rectangular or triangular in section, Exc 3Sqcm byt n.exc 6Sqcm, clean sawn, secured with nails or brads.

Dismantling of floor hearth and wall tiling including cement mortar bedding (but not backing) and removing serviceable like to store and rubbish off the premises., complete all as specified and directed by Engr-in-Charge.

M & L Non-skid coloured tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or beddding layer of CM 1:4, over 25mm thick PCC 1:2:4 type B-1 as a sub base to receive topping layer finished even and rough

M & L Non-skid coloured tiles, 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or beddding layer of CM 1:4, over 25mm thick PCC 1:2:4 type B-1 as a sub base to receive topping layer finished even and rough

M & L for coloured glazed ceremic tiles in vertical surfaces 450X 350X 7mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15mm thick rendering in CM (1:4) complete all as specfied and directed.

M & L for Glazed ceramic coloured tiles of size 300x200x7 mm thick on vertical surface such as in dado/skirting/risers to steps etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles laid over and including 10 mm thick rendering in CM (1:4), complete all as specified and directed by Engr-in-Charge.

M&L for Vitrified coloured ceramic tiles 10mm thick (squar / rectangular) area of each tile n. exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and jointed in white/coloured cement to match over and including 15 mm thick backing coat in cement mortar in (1:6), complete all as specified and as directed by Engr-in-charge.

Taking down shutter exc 1.00 sqm but not exc 2 sqm each and as directed by Engr Encharge.

Second class soft wood (KAIL) plain, framed, panelled shutters (any number of panels), 35 mm thick with panels of 9mm ply BWP commercial type or 12 mm thich of veneered particle board with commercial veneering both faces as in doors, complete all as specified and directed by Engr-in-Charge.

S&F 100 mm butt hinges medim weight cold rolled mild steel fixed with screws or welded all as directed.

S&F anodised aluminium barrel tower bolt extruded sections 200 mm size.

S&F 150mm long, mild steel handles cast type, fitted.

S&F Mild steel slidig door bolt 300 mm long plate type slove enamelled black wioth bright bolt not less than 12mm dia with and incl a minimum of 6 bolt and nut four on bolt plate and two on staple plate and fixed.

M&L for preparing previously untreated wood and wood based material of any description over 10cm width/girth and applying two coats of synthetic enamel paint over one coat of pink primer including preparation of surface.

S & F in repairs 18 mm to 20 mm dia curtain rod/rail, anodised aluminium alloy, chromium plated with & including fixing brackets, stops etc complete all as specified and directed.

Demolition of brick or stone/block masonry built in cement mortar including all quions, arches, pillars etc., but excluding ashlar facings, dressed stone works and precast cement articles, complete all as specified and directed by Engr-in-Charge.

M&L for Precast cememt concrete type-C-1 block masonary with solid blocks 1:3:6 (using 20mm graded crushed stone aggregate) exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.

M & L for 100 mm thick plain cement concrete 1:3:6. type C-2 (using 20mm graded stone aggregate) as in subbase to flooring and as in plinth protection without using extra cement complete all as specified & directed.

Dismantling of water tank exc 500 but n exc 1000 ltr capacity

Supply and fixed Rotational moulded HDPE water storage tanks (Cylindrical vertical closed top), double wall construction, hoisted and fixed in position or placed in position inside or outside the building, connecting up pipes and securing access covers complete, 1000 Ltr capacity, complete all as specified and directed by Engr-in-Charge.

Taking down GI tubing 15 mm dia, connections.

S&F in repair 16 mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and directed by Engr-in-Charge.

All as per item no. 26 above but 25mm outer diameter.

S&F in repair 25mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with bracket all as specified

S&F vitreous china wash hand basin (flat black) white of size 550x400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified.

S&F 32mm dia Waste coupling of PTMT for WHB including waste pipe complete all as specified.

S & F stainless steel squatting pan of pattern “long pan”, size 580 x 440 mm standard ivory with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe).

S&F 15mm bore PVC connection 600mm long both ends screwed with brass cap all as specified

S & F 15 mm dia Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15mm bore dia Stop valves, fancy type chromiun plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore Pillar taps fancy type, chromiun plated cast copper alloy, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

M&L for stone masonry walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, bulit in cement mortar 1:4, complete all as specified & directed.

S&F 500 ltr capacity rotationally moulded polythene water storage tanks (cylindrical vertical with closed top) multilayers layers of approved make hoisted & fixed at position.

M & L for 75 mm thick plain cement concrete 1:3:6. type C-2 (using 40mm graded aggregate) as in plinth protection complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

S & F in repair 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-Charge.

S&F in repairs Bib taps15 mm bore,fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for brass ferrule and fixed in repair, complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up PVC drain pipes

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor

Taking down cement plaster or any description including raking out joints, hacking for key, scrubbing down with water etc and removal of debris to a distance not exc 50 mts and depositing where directed.

M & L for 15 mm thick rendering in cement mortar 1:4 fair faces of brick work or concrete surfaces finished fair and even and smooth without using extra cement all as specified and as directed.

M & L for 15 mm thick rendering in cement mortar 1:6 fair faces of brick work or concrete surfaces finished fair and even and smooth without using extra cement all as specified and as directed.

Prepation of plastered or unplastered surfaces of walls and applying two coats of Cement base paint , complete all as specified and directed by Engr-in-Charge.

M&L for two coats of oil bound distemper on newly plastered surfaces of walls including preparation of surfaces.

M&L for two coats of oil bound distemper distemper on old wall surface with approved colour and shade complete as specified and directed by Enginer-in Charge. Make Asian Paints(Tractor)/Berger paints (Bison Super)

M&L for two coats of cement based paint on newly plastered surfaces of walls including preparation of surfaces.

M&L for precast cement concrete type B-1 (1:2:4) using 20mm graded stone aggregates as in lintels, landings, coverslabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:4 complete all as specified..

S & F MS structural steel work for roof trusses, pulines, rails, fastening, bracket, framing, beams, tee, angle, channels etc including distance pieces, cleat etc of Fe 410 W grade E -250 complete all as specified and directed.

S&F MS Plates (plain or chequered) channels, square cut or notched(ordinary and counter sunk)forming holes, without any attachment Fe.290.Gde-E-165.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

M & L for preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer described complete all as specified and directed.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5mm thick PVC sheet reinforced with mild steel square tube complete all as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing complete all as per specification and directed.

S&F aluminum anodized ‘D’ type handles 125 mm complete all as specified and directed .

S&F 150 mm aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S & F 100 mm Brass polished butt hinges type B12 complete all as specified and as directed.

S & F in repairs vitreous china wash basin white ,flat,flate back size 630x450 mm excluding taps,waste pipe,chain and plug and procelain stopper but including brackets complete all as specified and directed.

S & F in repairs for 15 mm pillar taps,cast copper alloy fancy type with chromium plated screwed down,screwed for iron pipe or for fixed in repairs.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc.

M&L Point wiring with multi-stranded copper conductor PVC insulated and unsheathed cable in PVC casing and capping, 1.5 Sqmm with all fittings/accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth including closed recessed wooden terminal Boxes of suitable size made of 2nd class hard wood for mounting switches, sockets etc with 3mm thick laminated sheet cover for one light point or bell/buzzer point controlled by one switch, complete.

All as per Srl item No 80 here in before but for one 3 pin 5 Amps switch socket on same board.

All as per Srl item No 80 here in before but for one 3 pin socket outlet 5 Amps on independent board.

Description all as per item No 80 here-in-before but using 4 Sq mm single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for industrial plug socket. point including running of 2.5 Sq mm copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

Switch piano flush type 5 Amps, single pole one way.

S&F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type.

S&F Switch socket combination 2 in 1, 5 and 15 Amps flush type.

Supply & fix LED building security light 45 watt energy efficient with bracket,suitable dia pipe for fixing the street light in wall all as directed. Make Havells or equivalent

Supply and fixing street light bracket made out of GI pipe 25/40 mm dia light grade 1.2 mtr duly bent in position as per site requirment and including 2 Nos and 2 set MS flat iron clamps of suitable size complete with Nut,bolts and washers for mounting sreet lights,complete all as specifide

Supply and fixing LED 18 Watt Tubelight fitting decorative ultra slim square profile linear with extruded polycarbonate environment friendly Make Havells or equivalent

S&F Ceiling rose surface bakelite 65x50mm, two to three terminals.

S&F Sheet metal enclosure for DB's Single door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required. Complete all as specified and directed.

S&F MCB, single pole, 5 to 32 Amp, 240V, 10KA.

S&F MCB, single pole and neutral, 63 Amp, 240V, 10KA.

S&F MCB, single pole and neutral, 40 Amp, 240V, 10KA.

S&F 1100 volts grade heavy duty 16 sqmm 2 core flat cableb PVC insulated aluminium stranded conductor,served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire withtwo single core cable complete all as specified.

M&L Earthing complete with galvanised steel earth plate electrode 600mm x 600mm and 6mm thick buried directly in ground not less than 2.25 mtr deep below normal ground level with top edge of plate not less than 1.5 metres below normal ground level, connected to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron protected by provision of G I light grade pipe 40mm bore including provision of concrete pit in PCC 1:2:4 type B1 using 20mm grade stone aggregate with 40mm thick cover of RCC 1:2:4 reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs two number and with 6mm dia MS bar handle made to shape and GI medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 40mmx8mm flat iron with fixing arrangement funnel wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50M all as per electric plate No 5 of SSR Part-I conected to earth test point as specified or indicated including testing on completion.

Lamp holder, insulated body with back plate suitable for batten fittings

S&F in replacement of LED bulb 12 watt . MAKE- HAVELLS/CROMPTON or EQUIV

Disconnecting the centrifugal pumping set of capacity 20-30 HP and reassembling after repair/replacing spare parts including testing and commissioning. Note:- 1. Spare parts required for replacement shall be measured and paid separately under relevant items as supply only. 2. Make of spare parts shall be of KSB/Kirloskar or as OEM approved.

Pump motor coupling suitable for pump 20-30 HP as per sample

Key to coupling stainless steel suitable for pump 20-30 HP as per sample

Bearing to pump shaft suitable for pump 20-30 HP as per sample

Refilling of gland suitable for pump 20-30 HP as per sample

Supply, installation, testing and commissioning of motor starter cap-20-30 HP, 415 volts, 3 phase, 50 Hz complete all as specified and directed by Engr-in-charge. Make: L&T/Havells

Excavation in trenches in hard/dense soil not exceeding 1.5mtr wide and not exceeding 1.5 depth, for foundation, etc, or for shafts, wells, cesspits, manhole, pier holes etc not exceeding 10 Sq m on plan and not exceeding 1.5 m in depth and getting out, complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick all as specified and directed.

Removal of surplus soil (excavated soil) to a distance not exceeding 50m and depositing where directed at a level not exc 1.5m above the starting point all as specified and as directed.

S&F Steel water tubing medium grade, ISI marked, 80mm bore of pipe galvanised with all fittings and fixed to walls and ceilings or laid in floors, Complete all as specified.

S&F Steel water tubing medium grade, ISI marked, 100mm bore of pipe galvanised with all fittings and fixed to walls and ceilings or laid in floors, Complete all as specified.

Supply, laying and testing of 3 layer PP-R(Polythene random copolymer) pipes of size 50mm SDR 7.4 (PN16) UV stablished and antimicrobial fusion having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches

Supply, laying and testing of 3 layer PP-R(Polythene random copolymer) pipes of size 40 mm SDR 7.4 (PN16) UV stablished and antimicrobial fusion having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches

Supply, laying and testing of 3 layer PP-R(Polythene random copolymer) pipes of size 25 mm SDR 7.4 & SDR 11 UV stablished and antimicrobial fusion having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches

Supply and fixing PP-R gate valve of size 50mm(Brass insert in size) as per site requiremnet as directed and instructed by Engr-in - Charge

Supply and fixing PP-R gate valve of size 40mm(Brass insert in size) as per site requiremnet as directed and instructed by Engr-in - Charge

Supply and fixing PP-R gate valve of size 25mm(Brass insert in size) as per site requiremnet as directed and instructed by Engr-in - Charge

Supply and fixing in replacement sluice valve of 100 mm dia class PN 1.6 as directed and instructed by Engr-in - Charge

Supply and fixing in replacement Non return sluice valve of 100 mm dia class PN 1.6 as directed and instructed by Engr-in - Charge

Supply and fixing CI flange of 100 mm dia class PN 1.6 by welding to existing GI pipes/fittings as directed and instructed by Engr-in - Charge

S&F water flexible suction pipe dia 100 mm, thickness 3 mm complete all as specified and directed.

S&F, Check valve/foot valve dia 100mm complete all as specified and directed.

Cleaning of RCC Underground/Semi underground reservoir / tank to be cleaned of silt and scrapping the internal surfaces of the tank with wire brush, removing the fungus, deposit and depositing not exceeding 100 mtr and washing the with bleaching powder solution including applying two coats of lime wash on internal surface of wall including ceiling, floor complete for 5000 Gallons capacity all as directed by EIC.

Sand cushioning with fine sand to under ground cables in trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable as specified in clause 19.75 of SSR Part-I.

Supply and laying un reinforced precast concrete cable cover class LV, type I, flat, size 250 mm x 150 mm x 40 mm

Dismentling of XLPE cable of any type any size from trenches including PCC precast cable cover and cable protection pipe.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 70 sq. mm 3.5 core complete all as specified

Note : Deduction for amount of Rs 21,108.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

M/S MOHD FAROOQ