SPL REPAIR TO SEWAGE LINE AND SEPTIC TANK AND ADDN/ ALTN TO BLDG NO P-5 AT GANDHINAGAR UNDER GE (AF) CHILODA

Amount

Demolition & breaking up Drain Pipe 150mm dia (Salt Glazed Ware, AC or Reinforced Concrete) set in Cement Mortar, complete all as specified and directed.

Demolition & breaking up Drain Pipe 200mm dia (Salt Glazed Ware, AC or Reinforced Concrete) set in Cement Mortar, complete all as specified and directed.

Demolition Cement Concrete (reinforced) of any description (above or below Ground Level) and removing debris, etc. to Outside of MD/AF Land, complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above GL) complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base etc. complete all as specified and directed.

M&L for Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick , set , jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes in floors , path / hard standing etc with grey cement and pigment (Coloured Tiles) complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation and in trenches as cable protection complete all as specified and directed.

M&L for Glossy finished pre-polished coloured machine pressed precast concrete interlocking paver block any shpe and size confirming to IS 15658-2006 of 60 mm thickness , M-35 grade with grey cement and pigments complete all as specified and directed.

Pavement quality concrete(PQC) of minimum 28 days field Flexural strength of 45Kg/ Sqcm or 4.5Mpa, aggregate gradation as per Table 3 of IRC 15 2017, coarse aggregate of clean , hard strong, dense non-porous and durable pieces of crushed stone or gravel, fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 360 kg/cum of cement with non -circular virgin synthetic fibre of 12-18 mm length, specific gravity 1.34 to 1 .39, UV stable, alkali resistant, with equivalent dia 15-40 micron, minimum melting temperature as 240°C and minimum tensile strength of 300 Mpa and at the rate as specified by the manufacturer. PQC laid, spread and compacted with slip-form paver of minimum 7.50 m width , including curing and tining by Texturing cum Curing Machine complete all as specified and directed. Required surface texturing to be done as specified in Clause -, rr,10 1 14 and Tabl~ 9 of IRC' 15-2017.

M&L 150mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base etc. complete all as specified and directed.

M&L 150cm thick (compacted thickness) WBM with coarse aggregates of grading 1 (90 to 40mm size), spread, rolled and consolidated to gradient and camber required complete all as specified and directed.

M&L Quarried rubble stone or broken nullah boulders, in large pieces for soling/sub base of road, etc. complete all as specified and directed.

Excavating in trenches, not exc. 1.50 metre wide and not exc. 1.50 Metre in depth for foundation, etc. or for Shafts, Wells, Cesspits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out in Soft/Loose Soil, complete all as specified and directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) as in Concrete Bed to Drain Pipes of 200mm bore (dia), including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) as in Concrete Bed to Drain Pipes of 150mm bore (dia), including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

M&L for Sail-glazed stoneware drain pipes 200 mm dia laid in trenches and jointed complete all as specified and as directed.

M&L for Sail-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and directed.

M&L Brick Work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Benching to Manhole including Forming Channel, laid to shape and Slope Coping, Plates including necessary Formwork and Fair Finished to Exposed Concrete Surfaces and Weathering, Slightly Rounded or Chamfered Angles and Throating, complete all as specified and directed.

M&L for Rendering 15mm thick in Cement Mortar 1:4 (Externally) on Fair Faces of Brick Walls or on Concrete Surfaces, mixing with WPC as per manufacturer's instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : WPC will be Measured and Paid separately as ‘Supply only’ under relevant Item. Repairs in patch work & height of walls upto 6.50 Mtr to be carried.

M&L Extra for Forming Fair finished Drain or Channel 30 Cm Inner Girth in Cement Concrete, using Extra Cement including Forms, Moulds, Stopped Ends, etc., complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed.

Returning, filling in approved Soft/Loose Soil including spreading leveling, watering and well ramming in layers not exc. 25 Cm thick, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs, Manhole Cover Slabs, etc., set in Cement Mortar 1:4, complete all as specified and directed. NOTE : Reinforcement will be Measured and Paid separately under relevant Item.

M&L TMT Bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm dia, complete all as specified and directed.

All as per item No 28 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

S&F Salt-Glazed Stoneware Gully Traps of size 150x150mm, type P, Square or Round Mouthed and fixed-in-repairs, complete all as specified and directed.

M&L for construction of Septic tank of size 8 Cum, PMF tank of size 2.90Cum, FFT tank of size 1.50Cum, TWT tank size 1.0Cum including sufficient pump for filter and arboriculture having capacity of sewage generation 3.00Cum/day including excavation and foundation of tank as designed by OEM and as directed by Engr-in-Charge complete for 50 user capacity. OEM : Sujal Eco Tech Pvt Ltd or techno commercially equivalent as approved by Garrison Engineer.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks) in One Brick thick Walls Honey Comb Walling, built in Cement Mortar 1:3, complete all as specified and directed.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Bands, etc., finished Even and Smooth without using Extra Cement, complete all as specified and directed. NOTE : Formwork & Reinforcement will be Measured and Paid separately under relevant Items.

M&L Loose filling with broken brick of gauge 80mm to 150mm (Broken Bricks) in Soakage Pits, Soakage Wells, etc complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling structural steel or Mild steel work of any discription not otherwise provided for, complete all as specified and directed.

Dismantling boarding any description, fixed in any position with nails complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 sqm but n exc 4.00 sqm each complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbingand polishing complete all as specified and directed.

M&L machine cut kota stone slab 20-25mm in riser of steps, skirting, dado and pillar thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbingand polishing complete all as specified and directed.

M&L Brick work with fly ash brick, old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L AAC Block straight or curved on plan exc 6m mean radius built in necessary adhesives complete all as specified and directed.

M&L ATT Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&LTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Taking down cement or cement lime plaster any description incl racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. Note :- Repairs in patch work & height of walls upto 6.50 Mtr to be carried

M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick work or concrete surfaces of walls finished even & smooth with out using extra cement complete all as specified and directed. Note :- Repairs in patch work & height of walls upto 6.50 Mtr to be carried

M&L for 5 mm thick cement plaster in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed. Note :- Repairs in patch work & height of upto 6.50 Mtr to be carried.

Supply only Liquid water proofing compound.

M&L preparing new surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L preparing new surface of wall and applying two coat of oil emulsion distemper over a coat of primer and 3 mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall over applying two or more coats of 100% Premium acrylic emulsion paint (weather) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Dismantling/removal of existing water proofing membrane of any description and removal of material out of MOD land/sites etc complete all as specified and directed.

M&L for rendering in CM (1:3) 10mm thick over RCC roof, chajja/ brick wall mixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement complete all as specified and directed. Note - WPC shall be measured and paid separately.

M&L for preapring clean and dried plaster surface and applying a coat of oil based bitumen primer confirming to (IS: 3384) at the rate of 0.30 litrs per Sqm and then laying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with non woven polyster reniforced membrane having thermal insulation with mineral gravel on upper side of membrane land on primed surface by torch application method complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for 12 mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed to aluminium frame work complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed by Engineer in Charge.

S&F powder coated Anodised aluminium two track sliding window and ventilator shutters, without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no each shutter) complete all as specified and as direced by Engr-in-charge.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 fixing complete all as specified and directed.

S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing in aluminium door and windwos shutter exc. 0.50 Sqm in Each Pane of Windows, complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles With Semi perforated 12mm thick micro tegular edged GRG false ceiling tilesof Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beam, rough finished of flat concrete surface including suppots, overhangs etc complete all as specified and directed.

M&L for Formwork to, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L providing reinforced cement concrete type B1 (1:2:4) using 20 mm graeded stone aggregate as in chajja complete all as specified and directed.

M & L for Reinforced cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm single core PVC insulated unsheathed multi stranded copper conductor FRLSH cable 1100V grade drawn through and incl PVC concelled conduit with accessories like bends tees, junction boxes etc fixed recessed in wall or ceiling etc including 1.5 Sqmm single core PVC insulated but unsheathed multistrandard copper conductor FRLSH cable 1100V grade as earth continuity wire incl modular sunken type pressed steel terminal boxes of size with 3mm thick bakelite steel white/coloured top cover for the following :- (a) One light point controlled by one switch complete

All as per item No 71 here in before but One fan point controlled by one switch.

All as per item No 71 here in before but One 3 pin socket out let 5 Amps on the independent board.

All as per item No 71 here in before but One 3 Pin socket out let 5 Amps on the same board.

All as per item No 71 here in before but with cable of size 2.5 Sq mm PVC insulated on independent board for power plug 15 Amps.

Supply and fixing Modular switch one way 6A,1 Module complete all as specified and directed.

Supply and fixing Modular switch one way 16A,1 Module complete all as specified and directed.

Supply and fixing Modular socket 6/10A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular socket 16/15A-2/3 pin combined 2 Module complete all as specified and directed.

Supply and fixing Modular Fan Regulator, 120W, 2 module complete all as specified and directed.

Supply & fix ceiling rose 3 terminal/ poly carbonate, isolated body complete all as specified and directed.

Supplying and fixing of sheet metal enclosure, single phase, double door SPN DB 8 way, flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links (without MCB's) SPN/ TPN complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing 240 Volts 10 KA 'Ç' Curve MCB SPN 4 pole of 40 Amp capacity complete all as as specified and directed.

Supply & fix MCB SP 6 to 32 Amps 10 KA 240 V, 10 KA 'Ç' Curve complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply & fix ceiling fans complete with blades, down rods as per site requirement , and accessories, 1 Phase, 230 V, 50 Hz, AC, 1200 mm sweep. Min air delivery 210 CFM with brushless direct current motor (BLDC, including down rod, Nut,Bolt,Clamp, hold fastener) complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified and directed.

M&L for brick protection cover to underground cable with sub-class ‘B’ old size over burnt bricks laid dry and flat across the axis of cable, abutting each other with gaps between adjacent bricks not exceeding 10mm complete all as specified & directed.

M & L for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6mm thick burried directly in ground not less that 2.25 m deep below normal ground level and top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI strip of size 25 x 4 mm by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical palte No 3 connected to earthing test point incl excavation, earth work in any type of soil strata, PCC chamber, 40 mm dia GI med grade pipe as protection of strip and 15 mm dia GI Med grade watering pipe, funnel, wire mesh etc including testing on completion complete all as specified and directed.

ALBA AC AND REF SERVICES (BID ID -3443679)

Shree Builders (BID ID -3442898)

Ramdev and Sons (BID ID -3443719)

Shreeganesh Construction (BID ID -3442672)

Priya Construction co. (BID ID -3442921)

Abhishek Enterprises (BID ID -3442786)

Haritwal traders (BID ID -3442884)

DMA PROJECTS (BID ID -3442825)