SANITARY FITTINGS AND FIXTURES, FLOORING, ROOF COVERING, WALL PANELING

Amount

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), ncluding cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed.

Dismantaling of brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar of any description, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified and as directed.

Taking down shutters of any descriptions area exceeding 1.00 Sqm but not exceeding 2.00 Sqm, complete all as specified and directed.

Taking down shutters of any descriptions, area not exceeding 1.00 Sqm, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-2 (using 40mm graded crushed stone aggregate), 75mm thick, as in plinth protection, finish even and smooth without using extra cement, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, 25mm thick, as in floors, finished even and smooth without using extra cement, complete all as specified and as directed.

Pre-cast cement concrete block masonry M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate) with solid blocks, exceeding 10cm in width and incluing setting in cement mortar 1:6, complete all as specified and as directed.

Pre-cast cement concrete block masonry of any typres of blocks, exceeding 10cm in width and incluing setting in cement mortar 1:6, complete all as specified and as directed. Note: Old PCC block/ bricks/ stone shall be used as retrivied from dismantling under serial item No- 1.02 here-in-before.

Plain cement concrete M-10(1:3:6), type C-1, (using 20mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates, including necessary form work, complete all as specified and as directed

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion and one coat of chalk whiting over one coat of plaster of paris putty 1.0mm thickness on plastered surface to prepare the surface even and smooth, complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement paint over one coat of lime wash, preparatory to surfaces, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing, complete all as specified and as directed.

Plain, solid, straight chowkats and frames, in second class hardwood, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as specified and as directed.

Factory made, plain framed, paneled shutter (two panel) 35mm thick, 2nd class hardwood with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

Glazed and skeleton shutters in second class hardwood, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

Glazed and skeleton shutters in second class hardwood, 30mm thick, divided into squares, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters of windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b); supplied and fitted to chowkhats, complete all as specified and as directed.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed.

Factory made steel window, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and and as directed.

Factory made steel ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and and as directed.

Plain cement concrete M-15(1:2:4), type B-1, (using 20mm raded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates and in hold fasts, including necessary form work, complete all as specified and as directed.

Butt hinges, size 100mm, medium weight, stainless steel, and fixed, complete all as specified and as directed.

Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed.

Butt hinges, size 75mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 200mm long and fixed, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed.

Extruded aluminium alloy handles, fabricated type, anodised, size 150mm, complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 140mm, fixed in floor, complete all as specified and as directed.

Door closer, aluminium extruded body section, hydraulically regulated, designation No-03, universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 Kg and fixed and fixing in repairs, complete all as specified and as directed.

Mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs, complete all as specified and as directed.

Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Preparation of old painted wood/ wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Anodised aluminium snap grid frame work for false ceiling, powder coated, comprising of aluminium Tee (weight of section not less than 280 gms/mtr) and aluminium angle (weight of section not less than 280 gms/mtr), grid size 605x605mm, including Hangers 6.0mm dia, galvanised iron (upto1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3 mm size 60mm long and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed.

Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions, complete all as specified and as directed by Engineer-In-Charge.

Curtain rod, 20mm dia, mild steel, fancy type, any colour coated with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing with wall plugs and screws, complete all as specified and as directed.

Mild steel flat clamps/ fixing brackets, end knobs, colour coated decorative types, made to shape to hold the curtain rods with wall plugs and screws, fixing in repairs, complete all as specified and as directed.

Tubes, 'medium grade' galvanised, 15mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Re-fixing of old tubes, galvanised, 15mm bore, with all required fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Old pipe shall be used as retrieved from dismantling. However cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Tubes, 'medium grade' galvanised, 20mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Re-fixing of old tubes, galvanised, 20mm bore, with all required fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Old pipe shall be used as retrieved from dismantling. However cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) with lid hoisted and fixed in position all as specified in SSR Part-I including ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) with lid, hoisted and fixed in position all as specified in SSR Part-I including ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed.

PVC (SWR) pipes, 110mm bore, single socketed, capacity not, less then 4.50 Kgf/Sqcm, in any length fixing with adhesive/ solvent cement, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) bends of 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

PVC (SWR) pipes, 75mm bore, single socketed, capacity not, less then 4.50 Kgf/Sqcm, in any length fixing with adhesive/ solvent cement, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) floor trap, 75mm diameter of outlet, plain with grating including jointing with adhesive, complete all as specified and as directed.

Vitreous China wash hand basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of PTMT (half or full threaded), fixing in repairs, complete all as specified and as directed.

Waste fittings, 32mm size, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, fixing in repairs, complete all as specified and as directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repairs, complete all as specified and as directed.

Low density polyethylene (LDPE) waste pipes of 32mm bore, pressure rating 6.0 Kgf/Sqcm), 900mm long, fixing in repairs, complete all as specified and directed.

Mirror cabinet, PVC, size 510mmx490mmx100mm including prefixed looking mirror, openable door with hinges, fixing in repairs, complete all as specified and directed.

Soap dish, stainless steel, fancy type, fixed to plugs with chromium plated brass screws, fixing in repairs, complete all as specified and as directed.

PVC connections 15mm size with brass nuts, of length 600mm, fixing in repairs, complete all as specified and as directed.

Sinks with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm, bowl size 410mmx330mmx160mm, fixing in repairs, complete all as specified and as directed.

Ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 15mm bore pipe, complete all as specified and as directed.

Ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, complete all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to dismantled floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, complete all as specified and as directed.

Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repairs, complete all as specified and as directed.

Plastic water closet seat, white/ ivory, closed, for pedestal pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixing in repairs, complete all as specified and as directed.

Grating doom, chromium plated, size 100mm dia, fixing in repairs, complete all as specified and as directed.

Brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Brass chromium plated basin mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Angle/ Stop valves, cast copper alloy, hromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Stop valves, cast copper alloy, hromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, fixing in repairs, complete all as specified and as directed.

Chromium plated shower roses including flexible steel braided pipe chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, for 15mm bore pipe, complete all as specified and as directed.

Vitreous China urinal, half stall, flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe, fixing in repairs, complete all as specified and as directed.

Jet spray with chromium plated, braided flexible pipe for water closet (English type), chromium plated, suitable for pipe of 15mm bore, complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, for 15mm bore pipe, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of white washing, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying two coats of white washing, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of ceiling and applying one coat of white washing, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of cement paint, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying two coats of cement paint, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of colour washing, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of distemper oil emulsion, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of distemper oil emulsion and including over one coat of chalk whiting after one coat of plaster of paris putty 1.0mm thickness on plastered surface to prepare the surface even and smooth,, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of distemper oil emulsion, complete all as specified and as directed.

Water storage tank lid, PVC lid , suitable for rotational moulded polyethylene water storage tanks of 500/ 1000 liters capacity, fixing in repairs, complete all as specified and as directed.

Preparation of old/ decorated, un-decorated, plastered surfaces of walls including complete removal of existing treatment and applying one coat of acrylic smooth exterior paint of required shade, complete all as specified and as directed.

Preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Disconnecting existing tanks capacity exceeding 250 liters but not exceeding 500 liters, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc, complete all as specified and as directed. Note: Cost of writing the date of cleaning on outer surface of water tank with synthetic enamel paint shall be deemed included in quoted rates.

Disconnecting existing tanks capacity exceeding 500 liters but not exceeding 1000 liters, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc, complete all as specified and as directed. Note: Cost of writing the date of cleaning on outer surface of water tank with synthetic enamel paint shall be deemed included in quoted rates.

Amount of Schedule of credit of for Rs 9,447.00 shall be deducted from quoted amount.

M/S Swarn Constructions (BID ID -3139025)