CA NO GE(N)AMB-47(P)/2020-21 WELCOME MAINT , DAY TO DAY MAINT AND REPAIR TO JOINERY , PLUMBING , SANITARY , ROOF , PLASTERING AND OTHER CONNECTED BLDG REPAIR WORKS IN AREA II MD ACCN AND OTHER AREAS AGE B/R-I OF GE(N) AMBALA CANTT

Amount

M&L 10 mm thick cement plaster in CM 1:3 on concrete surfaces finished even and smooth with out using extra cement on ceiling complete all as specified including dismantling of existing plaster, complete all as specified and as directed by the Engineer-in-Charge.

M&L 15 mm thick cement plaster on fair faces of bricks or concrete walls in CM 1:6 finished even and smooth with out using extra cement on brick work or concrete surfaces including dismantling of existing plaster complete all as specified and as directed by the Engineer-in-Charge

M&L 15 mm thick cement plaster on other then fair faces of brick works in CM 1:4 finished even and smooth with out using extra cement on brick work or concrete surfaces mixed with water proofing compound including dismantling of existing plaster complete all as specified and as directed by the Engineer-in-Charge

M&L for rough cast plastering including 15 mm thick rendering in cement plaster 1 :3 complete as specified in SSR Part-I clause 14.22 as given .Note : Rough cast finish : After applying under coat of cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1 shall be applied complete all as specified including dismantling of existing plaster complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of new plastered surfaces of wall and applying two coats of Acrylic distemper using painting roller including 2 to 3mm thck wall care putty complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and as directed by the Engineer-in-Charge

Complete removing to existing treatment on wall by washing , rubbing,down and stooping and applying applying two coats of Acrylic distemper using painting roller including 2mm thick wall care putty (JK wall / BIRLA white) complete all as specified and as directed by the Engineer-in-Charge

Complete removing to existing treatment on wall by washing , rubbing,down and stooping and applying applying two coats of Apex paint over a coat of primex and thin layer of wall putty of complete all as specified and as directed by the Engineer-in-Charge .(Make:- Asian or equivalent as approved by BOQ

M&L for preparation of wall by washing/rubbing to existing treatment and preparation of old plastered surfaces of wall and applying two coat of cement based paint complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of of old plastered surfaces of wall and applying two coat of white wash complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed by the Engineer-in-Charge

Prepation of old surfaces of steel any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge

Prepation of old surfaces of steel any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge

Prepation of old surfaces of wooden of any description not other wise decribed over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge

Prepation of old surfaces of wooden of any description not other wise decribed over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge

Providing and applying two coats of chlorphyros 20% EC with brush to wall / floor surfaces as in kitchen cabinets / Cup boards ,complete all as specified and as directed by the Engineer-in-Charge

S&Fin repair grating doom 100mm dia of PTMT (min weight 25gms) complete all as specified and as directed by the Engineer-in-Charge

S&F in repair 15mm dia size PVC connection with PTMT nuts of length 600mm complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia fixed with decorative brackets, stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge

S&F in repair bib taps 15mm dia fency type brass Chromium Plated with long body screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair brass CP wall/sink mixer for mixing hot & cold water for 15mm bore dia, pipes, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge. Note : for Wash hand basin and wall mixer including all connecting fittings except PVC connection) Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair brass CP WHB mixer for mixing hot & cold water for 15mm bore dia, pipes, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge. Note : for Wash hand basin and wall mixer including all connecting fittings except PVC connection) Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair of ISI marked fancy type pillar tap 15mm bore dia, cast copper alloy with capstan heads, chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge. Make : Make : Priyag/Hindware/Parryware/CERA/ESSCO.

M & L for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

S&F in repair of Angle valve 15mm bore stop valve, fancy type, brass chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair brass chromium plated tublar towel rail, 20mm dia, D type 60cm long between fkabges complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair for 15 mm dia angular stop valves of chromium plated with long shank and cup cocealed type screwed down high pressure with crutch or butterfly handle complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair viterious china white wash hand basin wall hung with pedestal white in colour ISI marked of size 550mm x 410mm x 190mm with chromium plated waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 type complete all as specified and as directed by the Engineer-in-Charge. . Make : Hindware/Parryware/CERA/ESSCO.

S&F in repairs viterous china squatting pan Orrisa pattern size 580 x 440mm white with "P" and "S" trap front or back inlet etc including connectipon to trap and to flishing to pipe , anti syphonage pipe etc incl provisioning of lime concrete complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair vitreous china wash down water closet pan ( pedestal pattern) white including connection to out going pipe and to flushing pipe and antysyphonic pipe etc including seat cover complete all as specified and as directed by the Engineer-in-Charge. .Make :Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repairs 10 ltr PVC valveless syphonic action type flushing cistern with brackets flush pipe etc complete including inlet ball valve float and handle including brackets of approved make including all connections & flush pipes for WC complete all as specified and as directed by the Engineer-in-Charge. .Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair for chromium plated toilet paper holder complete fixed to wall complete all as specified and as directed by the Engineer-in-Charge. . Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair for chromium plated shower rose 100mm dia or square complete fixed to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair glass sheet assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed by the Engineer-in-Charge.

S&F for chromium plated jet sprey (fusset) for EWC complete all as specified and as directed by the Engineer-in-Charge. . Make :Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair for stainless steel sink with out drainage board made of stainless steel 1 mm thick sheet for kitchen with waste coupling waste pipe , washer and including all necessary item including fixing to brackets and connected union to pipe complete of overall size 495 x 420 mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge. Make : Pryag/Jayna/Neelkanth/NIRALI

S&F PVC corner Self(Set of three) fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device complete all as specified and as directed by the Engineer-in-Charge. Make : :Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair stainless steel plate rack standred of size 750mm x900mm fixing with steel screw and complete all as necessary items complete all as specified and as directed by the Engineer-in-Charge. Make : : Pryag/Jayna/Neelkanth/NIRALI.

S&F for cabinet type looking mirror size 450 mm x 600 mm box type complete all as necessary items complete all as specified and as directed by the Engineer-in-Charge. Make ::Priyag/Hindware/Parryware/CERA/ESSCO.

S&F in repair for 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for chromium plated hand shower ( health faucut) with 8 mm dia 1 mtr long flexible tube and wall hook complete fixed to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Hindware/Parryware/Jaguar/CERA/ESSCO

M & L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete including ball valve 20mm dia all as specified including dismantling of existing water tank, complete all as specified and as directed by the Engineer-in-Charge.

M & L for 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete including ball valve 20mm dia all as specified including dismantling of existing water tank, complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair of ISI Marked 20mm dia Ball valves high pressure of brass with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified including dismantling of existing pipe, complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified including dismantling of existing pipe, complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius, complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing only for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified including dismantling of existing pipe, complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing only for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified including dismantling of existing pipe, complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings not exc 15 cm thick below or above G.L. complete all as specified and as directed by the Engineer-in-Charge.

M& L 25mm thick cement concrete 1:2:4 type B1 as in sub base of floors using 20mm stone aggregate, complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.11 but not exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 15mm cement screed bed in CM (1:4) complete all as specified including dismantling of existing tiles, complete all as specified and as directed by the Engineer-in-Charge.

M&L for glazed coloured ceramic tiles in vertical surfaces such as skirting /dados and riser to steps area of tiles 350mm x250mm x7mm/450x350x7mm thick set and jointed and pointing in white or coloured cement to match over 10 mm thick plaster in CM 1:4 all as specified including dismantling of existing tiles, complete all as specified and as directed by the Engineer-in-Charge.

M&L for vitrified tiles joint free 10 mm thick (square/ rectangular) area of each tiles exc 0.42 Sqm but n exc 1.00 sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match laid over 15mm cement screed bed in CM (1:4) complete all as specified including dismantling of existing tiles, complete all as specified and as directed by the Engineer-in-Charge.

Ditto as per item No 58 above but as in vertical, dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick plaster in CM 1:4 complete all as specified including dismantling of existing tiles, complete all as specified and as directed by the Engineer-in-Charge.

M & L for brickwork with sub-class `B` bricks, straight or curved on plan to any radius brick thick walls built in CM 1:4 complete all as specified including dismantling of existing brickwork, complete all as specified and as directed by the Engineer-in-Charge.

M & L for 20 mm thick granite (Black Jet colour) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding the edges complete all as specified and as directed by the Engineer-in-Charge. including dismantling of existing stone.

S&F II class HW 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply of 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (part-1) kiln seasoned and chemically pressure treated and making good to distrubed portion with match the existing surfaces all as specified including dismantling of existing shutter, complete all as specified and as directed by the Engineer-in-Charge.

S&F for 35 mm thick II class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc. (with out sash bars) ,edges or framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc and making good distrubed portion with existing surface all as specified including dismantling of existing shutter,complete all as specified and as directed by the Engineer-in-Charge.

S & F 40mm thick flush shutter solid core construction with partical board core and plywood face panels commercial type on both sides including dismantling of existing shutter,complete all as specified and as directed by the Engineer-in-Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified including dismantling of existing chowakts, complete all as specified and as directed by the Engineer-in-Charge.

S & F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified including dismantling of existing shutter, complete all as specified and as directed by the Engineer-in-Charge.

M & L for cutting holes into exc. half brick but not exc. one brick thick walls, built in cement mortar or cement lime mortar and stone walls, for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall) complete all as specified and as directed by the Engineer-in-Charge

S&F II class HW Plain , Solid ,Straight Chowkhats and frames ,wrought , framed rebated on the solid ,rounded or champhered put together with glue pinned at joints, complete all as specified and as directed by the Engineer-in-Charge.

M&L for 18 mm thick MDF board prelaminated MDF board , exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet ,self for cupboard including cut edges of prelaminated board to be sealed with 6mm teak lipping and all necessary fittings complete all as specified and as directed by the Engineer-in-Charge.

M&L for 12 mm thick prelaminated partical board interior grade prelaminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work complete all as specified and as directed by the Engineer-in-Charge.

S&F 30mm wide Continuous (piano) hinges, mild steel, bright finish or electrogalvanised fixing to wooden frame complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm long fency type Stainless steel handles, cast type, polished bright complete all as specified and as directed by the Engineer-in-Charge.

S&F magnet catcher fixed in cabnet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

S& F wooden plain fillets of 2nd class hardwood of area exc 6 sqm but not exc 13 sqm complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair stainless steel telescopic channel of best quality available in market (Hetlic) wooden paint healy complete all as specified and as directed by the Engineer-in-Charge.

Stainless steel (302 grade) modular litchen pull out trayes, baskets,cutlery trays , big utensils trays etc of shape & size complete all as specified and as directed by the Engineer-in-Charge. . Make -HETTICH ,Jaguar,KAFF

S & F stainless steel handle 150mm long for kitchen cabinets /cup boards of best quality complete all as specified and as directed by the Engineer-in-Charge.

S & F 100mm long mortice latch with two levers (vertical type), mild steel body complete all as specified and as directed by the Engineer-in-Charge

S&F for aluminium section of any size as directed for frame / shutter for door, window, ventilator, and all necessary aluminum hinges complete all as specified including dismantling of existing shutter, complete all as specified and as directed by the Engineer-in-Charge.

M&L for aluminium grill for window and other similar works 10 mm dia including fixing for frame complete all as specified and as directed by the Engineer-in-Charge.

M&L for 4.8 mm thick tinted glass fixed to aluminium frame including rubber bead complete all as specified and as directed by the Engineer-in-Charge.

S&F for framed work as in door of angle or other section with gusset plate , rails , braces, etc complete drilled for fixing of steel sheeting or other covering. Door etc, to be prepared hanging or sliding with and including either hooks and hinges or steel hanging door fitting and hanging also fastening and fixing including one shop coat of zink chromate primer paint confirming to F-410W GDe-250 A complete all as specified and as directed by the Engineer-in-Charge.

S&F for steel window box type double shutter ( glazed with wire gauge)with side hung shutters including hinges with steel handle and steel peg stay complete with glazing bar dovetailed or welded and including window guard bar, tower bolt,flat iron for fixing wire netting including one shop coat of zink chromate primer paint and making good to distrubed portion match with existing surfaces complete all as specified and as directed by the Engineer-in-Charge.

S & F 150mm aluminium handles, cast type, anodised complete all as specified and as directed by the Engineer-in-Charge

S & F rubber strips 3 to 4 mm thick and 65 to 75 mm wide on bottom rail of door for covering geps between door and floor to avoid entry of inseeds , dust etc, complete all as specified and as directed by the Engineer-in-Charge.

S & F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing for butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed by the Engineer-in-Charge.

S & F Aluminium body (die cast) Hydraulic door closer fixed to chowkats suitable for wooden shutter complete all as specified and as directed by the Engineer-in-Charge. . Make - Sandhu

M & L for sheet glass 3.0mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge

S & F for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed by the Engineer-in-Charge.

Prepation of new surfaces of wooden of any description not other wise decribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

Prepation of new surfaces of steel any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Demolition of reinforcement cement concrete in ground floor and pavings not exc. 15cm thickness (below or above GL) complete all as specified and as directed by the Engineer-in-Charge.

M&L RCC (Nominal mix) 1:1 1/2:3 (20mm grded aggregate) type B1 as in chajjas, shelves and similar works match complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT bars bars 10mm dia and over, cut to length, bent to shape required, including, cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe- 410-W (Gde E250) Quality -A or Fe 290 (Gde E-165) complete all as specified and as directed by the Engineer-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, chajjas, shelves including supports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and as directed by the Engineer-in-Charge.

S & F 5mm PVC hollow sheet (wall panelling) inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified and as directed by the Engineer-in-Charge. including dismantling of existing paneling.

Cleaning of water tanks of any size 500 to 1000 ltr capacity including removel of all scales , dusts etc , opening of stop valva, float valva & refixing in the same position and complete all as specified and as directed by the Engineer-in-Charge.

Cleaning of bushes , removel of trees , vegetation from wall , roof not exc 30 cm girth& removel of rubbish not exc 50 m away, complete all as specified and as directed by the Engineer-in-Charge.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M&L concrete bed to drain pipes of 110 mm bore including packing under and harching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C1 complete all as specified and as directed by the Engineer-in-Charge.

Cleaning of blockage of WC , Bath including removel of sludge upto Ist mainhole, complete all as specified and as directed by the Engineer-in-Charge.

Cleaning of sludge from Ist main hole and including removel of sludge exc 50m but not exc 1.00m, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair viterous china white table top wash hand basin with chromium plated waste coupling, waste pipe, PVC connection and all connected fittings complete all as specified and as directed by the Engineer-in-Charge. Make - Jaquar Cat Part No : FLS-WHT-5931 or equivalent in parryware/Hindware/CERA

S&F in repair Single pieace water closet wtih PP soft close seat cover, Hingles, fixing accessories and accessories set, cistern fittings S or P Trap complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar cat Part No SLS -WHT-6855S or equivalent in parryware/Hindware/CERA

S&F in repair for CP Brass wash hand basin mixer for mixing hot and cold water screwed down for 15mm dia pipe including waste popup waste with 450mm long braided hoses and all connecting fittings complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No FLR-5001B OR or equivalent in parryware/Hindware/CERA

S&Fin repair for CP wall mixer for mixing hot and cold water including telephonic shower and all connected fittings screwed down for 15mm dia pipe complete all as specified and as directed by the Engineer-in-Charge. Note : Sample as approved by GE/EIC Make : Jaquar Cat Part No FLR 5123 or equivalent in parryware/Hindware/CERA

S&F in repair for bib tap 15mm dia chromium plated fency type with crutch or butterfly handle screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge. Make :Jaqua Cat Part No : OPP-15037PM or in parryware/Hindware/CERA

S&F in repair 15mm bore angular valves, fancy type chromium plated with long shank and cup (Consealed) type complete all as specified and directed of Make :Jaquar : Cat Part- FLR 5053N or equivalent in parryware/Hindware/CERA

S&F in repair CP Single towel rail 20 mm dia D type 600 mm long between flanges including brackets complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat part No : AQN-7711 or equivalent in parryware/Hindware/CERA

S&F in repair CP Single towel rack 600 mm long between flanges including brackets complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AQN-7781 in parryware/Hindware/CERA

S&F in repair CP Towel ring round between flanges including fixing with brass screws complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AQN-7721 or equivalent in parryware/Hindware/CERA

S&F in repair CP toilet paper holder including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AKP-35751P or equivalent in parryware/Hindware/CERA

S&F in repair CP SOAP DISH HOLDER including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AKP-35731P or equivalent in parryware/Hindware/CERA

S&F in repair Corner glass slelf (with bracket) including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : CAN-1173 or equivalent in parryware/Hindware/CERA

S&F in repair glass slelf (with bracket) including fixing with brass screws to wall complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : CAN-7771 or equivalent in parryware/Hindware/CERA

S&F in repair 5-6mm thick mirror including ingraved any pattern, or with wooden beading of any size fixed to wall with CP screwd with top cap and all connected fitting complete all as specified and as directed by the Engineer-in-Charge.

Dismentling of asbastos cement corrugated or semi corrugated in roof covering /wall clading complete all as specified and as directed by the Engineer-in-Charge.

S&F for pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering /cladding to wall fixed with self taping screws complete all as specified and as directed by the Engineer-in-Charge.

S&F for pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering /cladding to wall fixed with self taping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of wooden scantling as in purlins, rafters etc complete all as specified and as directed by the Engineer-in-Charge.

S & f Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed by the Engineer-in-Charge.

S & F wash hand basin chinaware including cabinet , drawers complete set as approved by GE including waste coupling bodal trap complete all as specified and as directed by the Engineer-in-Charge. Make- Jaguar/hindware/parryware

Taking out existing surface wiring and refixing in the same after cutting consealed in brickwork including removal of switches, sockets & refixing in the new hylon sheet of including replacement of hylan sheet to be fixed on top of tiles and making good the distrubed portion to makes the existing complete all as specified and as directed by the Engineer-in-Charge.

Taking out existing kitchen cabinets including drewers and refixing in the same position after easing repairing the existing channels , wooden fillets / members (replacement of handles , telescope channel, fillets )boards will be measured & paid seperatly complete all as specified and as directed by the Engineer-in-Charge.

Shiv Construction Co.

bhagwandasswazirchand

Puneet Sharma