1406/DP EKM 21-22,CONSTRUCTION OF AKANADU HSS SCHOOL BUS SHELTER MUDAKKUZHA GP

Amount

BUS SHELTER

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

od1564183/2021_2022 : od1282821/2021_2022 :Providing and fixing Aluminium profile sheets (size, shape and pitch of corrugation<br>as approved by Engineer-in-charge) 0.460 mm or nearest available thickness. The sheet shall be fixed using<br>self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/<br>vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size<br>and shape wherever required. OD71/21-22 (Approved data vide CE circular dated 18.08.2016)

od1564074/2021_2022 : Providing and fixing rain water gutter semi circular section using 150mm dia. 6kgf PVC pipe including fitting with 32x5mm flat supporting at 1m intervals complete as per the direction of engineer in charge at site.

od1571976/2021_2022 : od1283442/2021_2022 :Designing, fabricating,testing and installing Curtain Wall with Aluminium Composite<br>Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights<br>and all levels etc. including:<br>Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding INCLUDING<br>aluminium base frame work in pan shape in metalic colour of approved shades made out of 4mm thick<br>aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between<br>two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and<br>shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts,<br>bolts, washers, cleats, weather silicone sealant, backer rods etc.with aluminium composite panel cladding<br>till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium<br>composite panel cladding, having all the performance characteristics all complete, as per the Architectural<br>drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the<br>Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face of the<br>curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm.<br>up to two decimal places.<br>OD84/21-22 - Modified data 25.7

50.18.9.18.2 : Providing and fixing PVC pipes including fixing the pipe with clamps/Clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 4 Kfg/cm2 - External work - Exposed on wall

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

16.91.2 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

od1564356/2021_2022 : od1283430/2021_2022 :Supplying and fitting Stainless Steel (grade 304) 3D Lettering ENGLISH of size 10-<br>15cm, 20-30mm projection etc complete as per direction of Engineer incharge at site OD76/21-22

od1564371/2021_2022 : od1283431/2021_2022 :Supplying and fitting Stainless Steel (grade 304) 3D Lettering ENGLISH of size 25-<br>30cm, 30mm projection etc complete as per direction of Engineer incharge at site OD77/21-22

od1572017/2021_2022 : Supplying and fixing in place granite nameboard of slab area less than 0.9sqm<br>including engraving and painting letters etc complete as per direction of Engineer incharge at site OD 79/21-<br>22

BASIL P VARGHES

KM ROY

K P PAULOSE

Bidder Name

K P PAULOSE

BASIL P VARGHES

KM ROY

JITHIN XAVIER