GER-74/2020-21 SPL REPAIR TO BLDG NO T-31 T-8 SECURITY WALL AND RETAINING WALL CERTAIN REVENUE AND MINOR WORK UNDER AOR OF DETT B AT RAJOURI

Amount

Sch 'A' Part-I (B/R Works) Dismantling of corrugated or semi corrugated asbestos cement sheets roof coverings complete all as specified and directed.

Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

Pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc all as specified and directed.

Rolled mild steel joist, channel, angle, flat iron or Tee section, fixed independently, without connecting plates etc (cut to ordinary length ie within 20mm of the length indicated) conforming to Fe 290 grade E-165 complete all as specified and directed.

4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions , laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling existing board complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

Walling of random rubble masonry (except stone), uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

Plain cement concrete 1:3:6 type C 1 (using 20mm graded stone aggregate) as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting CM 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 40 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed.

Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Rendering 20mm thick on stone masonry or other than fair faces of brick wall in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

Rendering 20mm thick on stone masonry or other than fair faces of brick wall in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (Ist quality) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Glazed ceramic coloured tiles of size 350x 250x7mm or 450x350x7mm thick as on vertical surface of wall such as skirting, dado, riser etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of cement primer complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

Complete removal of existing treatment from old decorated surfaces of walls and applying two coats of cement base paint over and including a coat of cement primer complete all as specifed and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each and removing to store complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4.00 Sqm each and removing to store complete all as specified and directed.

Anodised aluminium frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 No, floor door stopper, anodised aluminium snap beading, screws etc including powder coating of any colour (thickness of powder coating not less than 50 micron) complete all as specified and directed.

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Aluminium anodized grills 6.3mm dia decorative type 75mm mesh size complete all as specified and directed.

Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg Aluminium (extruded section) body complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Brass mortice lock vertical type 100mm long with 4 levers complete all as specfied and directed.

5.5mm thick sheet glass, ordinary quality fixed to aluminium doors in square exc 0.5 sq. m in each pane complete all as specified and directed.

Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level complete all as specified and directed.

50mm thick PCC type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand(all by weight) complete all as specified and directed.

0.63 mm galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with 'L' or 'J' type hooks or cranked hook bolts and washers in roofs, walls etc with grade of zinc coating 275 gm/sqm complete all as specified and directed.

0.80 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of Zinc coating 275 gm/sqm complete all as specified and directed.

Preparation of newly plastered surfaces on walls and applying three coats of white wash complete all as specified and directed.

75mm thick PCC 1:5:10, type D-2 using 40mm graded stone aggregates as in sub base of floors complete all as specified and directed.

Machine cut Kota stone slab flooring 20-25 mm thick as in flooring area of each slab not less than 0.30 sq.m, (cut to size in square shape) laid over & including 20 mm thick cement mortar (1:3) screed and jointed with grey cement slurry mixed with matching shade pigment including rubbing and grinding to achieve mirror finish complete, all as specified and directed.

Rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including dismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including ball valve of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minium weight 15mm-142 gms including dismantling existing tanks complete all as specifed and directed.

Taking up or down GI tubing 15 mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.

Taking up or down GI tubing 20 mm bore and connections including cleaning for refixing or removal complete all as specifed and directed.

15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specifed and directed.

20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, Tee, Elbow, union, Nipple, short pieces and fixed to walls, ceilings or laid in floors complete all as specifed and directed.

15mm bore cast iron plug type bib taps, cast iron, screwed for iron pipe or for ferrule complete all as specified and directed.

Kitchen sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

32mm bore brass chromium plated trap ‘P’ or ‘S’ pattern for wash basins and sinks with inlet and outlet, screwed for pipe or connections, and with one cleaning cap and fixed complete all as specified and directed.

32mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

PCC type C-1 (1:3:6), using 20 mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finish to drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc complete all as specified and directed

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Reinforced cement concrete 1:2:4, (Nominal mix) type B-1 (Using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

100mm thick plain cement concrete type B-2, 1:2:4 (using 40mm graded aggregate) as in floor complete all as specified and as directed.

Rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Use & waste of formwork to sides of concrete foundation, footing, bases of colums, raft & raft beams, sides and soffits(if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

Broken glass coping on top of walls in CM 1:3 complete all as specified and directed.

Hand packing (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and directed.

Rolled mild steel work conforming to grade Fe-410-W (Gde-E-290) quality A for water tank staging and the like includinjg caps, bases splices etc built up from two or more beam or channel sections or angles with plates, including all lattice bass, stiffeners, gusset plates etc. complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

PCC 1:4:8, type D-2 (using 40mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

Brick work using old size bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4), complete all as specified and directed.

Steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified and directed.

3mm thick sheet glass ordinary quality and glazing with oil putty in squares n . exc 0.50 sqm in each pane complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick on other than fair faces of brick work or concrete surface in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

25mm thick cement concrete type B0 1:2:4 (12.5mm graded aggregate) as in floor complete all as specified and as directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (Ist quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Glazed ceramic coloured tiles of size 300x 200x7mm/ 350x250x7mm thick as on vertical surface of wall such as skirting, dado, riser etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile fixed over and including 15mm thick backing layer of cement plaster in CM 1:4 complete all as specified and as directed.

Supply only PVC low level flushing cistern 10 ltrs capacity white with inlet ball valve, float valve and handle including providing & fixing MS angle iron brackets, PVC flush pipe complete all as specified and as directed.

Vitreous China water closet (squatt pan) Orissa pattern 580x440 mm size pan, white, with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to flushing cistern/pipe complete all as specified and directed.

Bib tap cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.

15mm bore stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore complete all as specified and directed.

75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

PVC SWR bends of 75 mm bore complete all as specifed and directed.

PVC (SWR) pipes type 'B' single socketed in any length with rubber ring joints , laid in trenches or in floor, of bore 75 mm complete all as specified and directed.

Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screw, pointing around urinal back in cement, including providing and fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified and directed.

Vitreous China wash hand basin oval hape 550x400mm including including brackets or bedding CM 1:4 PVC waste pipe, PVC connection and waste coupling complete all as specified and directed.

15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Pre-cast cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate) for cover slab, manholes etc, set in CM 1:4 complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

Rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs including dismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including ball valve of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minium weight 15mm-142 gms complete all as specifed and directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S . frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR Part-II 2010 complete all as specified and directed.

Butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed.

Aluminium anodized barrel tower bolts 150 mm long of extruded section all as specified and directed.

Extruded aluminium alloy handles size 125 mm fabricated type anodised complete all as specified and directed.

LLDPE septic tank of capacity 10 users designed to carry sewage and sludge water, excavation in any type of soil, PCC 1:4:8 type D-2 in foundation, vent shaft, connection etc including refilling of soil at sides of tank, well ramming in layers and removing excavated surplus soil to a distance not exc 50m complete all as specified and directed.

Construction of soakage well 1.2 Mtr dia and 3 M deep including excavation and earth work in any type of soil, PCC 1:3:6 type C-2 in foundation, walls of honey combed masonry with top ring of M-25 concrete including intercerpting chamber and screen chamber made of Brick masonry in CM 1:4, RCC cover slab in M-25, interconnecting pipes of RCC complete filled with brick bats complete all as specified and shown on drawing No CE/TD 1202/2008 SH 1/2 & 2/2.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm bore SGSW pipe complete all as specified and directed.

150 mm internal dia Salt-Glazed stone ware drain pipes grade 'A' laid in trenches over concrete bedding jointed in cement mortar 1:1 and tested complete all as specified and directed.

PCC type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, hold fast, water troughs, bed block and the like including weathering, slightly rounded or chamfered angle and throating incuding necessary form work complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick work, surface finished even and smooth without using extra cement including mixing of water proofing compound as per manufracturer's instructions complete all as specified directed.

Supply only integral water proofing compound complete all as specified and directed.

Hard core of broken stone or boulder of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

Chequered cement concrete tiles of size 30 cm x 30cm x 25 mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 20 mm thick cement screed bed in CM 1:6 complete all as specified and as directed.

Providing, cement concrete type B1, 1:2:4 (using 20mm graded aggregates) in roof kerbs or mud stops, rounded or chamfered on edgecomplete all as specified and directed.

Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Concertina coil 1050 mm dia, 56 loops, 2.5mm core wire heavy galvanised (wire-275 GSM & strip-200 GSM), tensile strength of wire 1400-1500 N/Sqmm, weight 14.63 Kg/coil, stretchable length 12M inlcuding securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.

RCC M-25 design mix (using 20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, column etc for rought finished surface of concrete complete all as specified and directed.

RCC M-25 design mix (using 20mm graded aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete complete all as specified and directed.

RCC M-25 design mix (using 20mm graded aggregate) as in slab, shelves complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

RCC M-25 design mix (using 20mm graded aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

RCC M-25 design mix (using 20mm graded aggregate) as in chajja and tghe like over 1.5m span complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Rendering 5mm thick on ceiling in CM 1:3 finished fair even and smooth without using extra cement complete all as specified and directed.

Preparation of newly plastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290. Gde-E-165 complete all as specified and directed.

Pressed steel door frame of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC 1:3:6 type C-0 using 12.5mm graded stone agregate complete all as specified and directed.

Steel ventilators with centre hung shutter including hinges, steel peg stay complete all as specified and directed.

Factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Aluminum alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Surface dressing n exc 15cm complete all as specified and directed.

Sch 'A' Part-II (E/M works) Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Point wiring for one light point/fan point controlled by one-one way switch with 1.5 Sqmm (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable drawing in and including non metalic rigid PVC casing & caping complete with all acessories including PVC sunk box ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated bakalite sheet as top cover, and 1.5 Sqmm (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly compete all as specified and directed.

Description all as per Serial item No 128 above but for one 3 pin 5 Amp socket outlet on independent board complete all as specified and directed.

Description all as per Serial item No 128 above but for one 3 pin 5 Amp socket outlet on same board complete all as specified and directed.

Description all as per Serial item No 128 above but for one 3 pin 15 Amp socket outlet independent with cable 2.5 sqmm PVC insulated FRLS multistranded copper conductor cable with 2.5 sqmm single core multistranded FRLS copper conductor cable as earth lead complete all as specified and directed.

Switch piano, flush type single pole, one way 5 Amp, 240 volts complete all as specified and directed.

Socket out let 2 in 1, 3 pin 5 amp flush type complete all as specified and directed.

Socket out let 2 in 1, multipurpose 5 & 15 Amp flush type complete all as specified & directed.

Ceiling rose two to three terminal (65 x 50mm), PVC/ polycarbonate insulated body complete all as specified and directed.

Ceiling fan regulator elctronic, stepped type, hum free suitable to control speed of fan from 0 to 100% rotary type five step 240 volts AC complete all as specified and directed. Make Bajaj /Usha/havells/CG

Lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/angular/pendent fittings including LED lamp 15 watt complete all as specified and directed.

Sub main wiring complete with 2 runs of 6 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade multi stranded copper conductor cable along with one run of 6sqmm single core PVC insulated FRLS cable 1100 volts grade multi stranded copper conductor as earth continuity conductor drawn through and including 25mm dia rigid PVC conduit and conduit accessories fixed on wall/floor/ceiling etc all as specified and as directed. Note: 03 runs of cable and one run of conduit shall be measured as one unit.

Switch socket combination 2 in 1, 5A, 230 volts flush type complete all as specified and directed

LED tubelight fitting complete integrated type with indoor decorative PVC extruced body of 7 watt 1 feet (whiteO with all accessories pre wired and connecting electrically to ceiling rose using pvc insulated and over all sheathed flexible copper conductor cable of size 75 sqmm 3 core complete all as directed. Cat par No crompton LCL-07-CDL or equivalent in Havells/ Bajaj

Supply and fix in replacement high efficacy 2'x2' recess LED flat panel light 36W LED 2700/3000K (warm white) edge-lit luminaire suitable for armstrong/grid ceiling complete for low ceiling applications complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make:- Havells/Bajaj/Crompton/Halonix.

Surface mounted LED bulk head fitting (e-trata) plastic housing with clear prismatic diffuser and lamp holders etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size cat part NO CG80IB6WLED of C&S or equivalent in Havells/Phillips complete all as specified and directed.

LED Tube light fitting T-5 LED, Battens type 1x 18 watts, 4 feet white Indoor decorative aluminium extruded, integrated type complete with all accessories prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm complete all as specified & as directed by Engr in Charge. Make C&S model No. LTTB4F18WLED P/W or its equivalent technically and commercially in Philips/Havells/Bajaj/Crompton

Sheet metal enclosure MCB distribution board in repairs single pole & neutral 430 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .(Note-MCBs will be measured and paid for separately).

Sheet metal enclosure MCB distribution board in repairs single pole & neutral 430 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .(Note-MCBs will be measured and paid for separately).

Sheet metal enclosure MCB distribution board in repairs single pole & neutral 430 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .(Note-MCBs will be measured and paid for separately).

MCB SP 240 volt any rating from 5 to 32 amps conforming to IS 8828 of 1996, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified & directed.

MCB SPN 240 volts 40 amps conforming to IS 8828 of 1996, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified & directed.

Exhaust fan of size 300 mm heavy duty metalic body complete with louver 1400 RPM speed 230 volts AC electrical operated 50 HZ Model No. Turbo Force SP of Havells or its equivalent of Orient/ Usha/ Bajaj/CG.

Sheet metal enclosure single pole and neutral with two pin and earth plug and socket with one single pole MCB 20 amp complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m depth for laying of cable and foundation of poles and stays and n. exc 10sqm on plan and getting out in any type of soil complete all as specified and as directed.

Sand cushioning to underground cable, provided with a layer of 8 cm deep before laying the cable and 15 cm thick after laying and stretching jointing and testing the cable complete all as specified and as directed Note: Punned thickness of sand shall be measured and paid.

XLPE cable insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sq mm 2 core laid in trenches/ on poles/ under road crossing etc. includig testing complete all as specified and directed.

Brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat, size 230mm x 115mm x 75mm, complete all as specified and as directed

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm (soil) thickness all as specified and directed.

Removing of excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion complete all as specified and directed.

Storage water Heaters verticle type ( Geysers) of cap 25 Ltrs , 5 star rated as per BEE norms electrically operated suitable for 230 volts , 50 HZ AC supply system complete with porcelain/glass coated insulated heating element, copper inner tank, external thermostate including CP connections grouting of suitable nut, bolts etc complete all as specified and directed. Make Bajaj shakti /CG/ Venus/ Ditz.

Air circulated heavy duty, 600mm metalic body with metalic blades legs, ISI Marked energy efficient wall mounted type connection up including provision of three core flexible copper wire size 2.5 sqmm from ceiling rose to air ciculator complete all as specified and directed. Make - Havells/Bajaj/Crompton or equivalent

GI pipe 40mm bore light grade (ISI marked) with all fitting fixed to wall, poles or under road crossing etc with suitable size clamps for protection of cable complete all as specified and directed.

Street light fitting LED 30 watt made up of grey powder coated pressure die cast aluminium housing having IP66 control gear and lens compartment. Fixture should have isolation in lense compartment and driver compartment and fitting must be top openable for easy maintenance and remain intact its IP protection forever after once it is open for repair. IP protection should be intacted for enhancing the overall efficiency of light. Fixture and driver should be of same make. Driver of the fixture must have enclosure and having vent from ends to prevent the driver from condensation effect and it should be BIS approved and R number should be mentioned on the top of the LED driver having voltage band of 110-300 Volts AC, THD <10% KV and also having surge protection inbuilt on driver is min 5KV and external SPD of 10KV outside the driver inside the fixture to prevent the fixture from non requirerd SUGRG. Driver should be equipped with over voltage short circuit and reverse polarity protections, driver must be constant current and constant voltage based (CVCT) fitting should having system efficiency of more than 100 lumens/watt. Fixture should be equipped with secondary lenses for better distribution of light. OEM must have its own manufacturing facility in regards to this OEM must produce the necessary documents of its own manufacturing along with the details of testing equipment and the respective Make : Crompton Cat Part No LSTP-30-CDL or its commercially and technically equivalent in Bajaj/Philips/Havells/C&S Note :-1. Contractor shall obtain LM 79 and LM 80 test report (Electrical, photometry and chromaticity) (from third party NABL Lab only and inhouse NABL lab test will not be considered) for the light fitting from the manufacturer before supply of material and submit to the department. 2. A certificate of Guarantee shall be submitted by the contractor for period of 3 (three) years from the certified date of completion of work as a whole for repair/replacement of lamp and light fittings to GE. Performance guarantee amount @5% of quoted amount of LED lamp and light fittings shall be kept reserved for a period of three years. Accordingly ,performance guarantee amount shall be released after gaurantee period. 3. The manufacture LOGO shall be embossed into housing of luminaire. 4. Luminarie shall be provided with all parameters mentioned above. 5. Make of LED chip should be Cree, Nichia, Lumiled, Osram.

Supply and fixing street light bracket made out of 32mm bore GI tubing medium grade made to shape 1.2 mtr long bent to shape 120 degree and fixing with two numbers of MS clamp of 32mm x 3mm thick flat iron including , nuts, bolts, washer duly painted with synthetic aluminium paint two coats over a coat of red oxide primer complete all as specified and directed.

Supply, Laying, connecting and testing in replacement of service cable of size 10 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metallic rigid PVC conduit as per site requirement, flat or circular complete all as specified and directed.

Cutting the existing 20mm tubing and inserting GI Tee 50 x 50 x 25mm dia inlcuding necessary screwing threading, tail pieces, short pieces, jointing material etc complete all as specified and directed.

House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified and directed.

Exhaust fan of size 250 mm heavy duty metalic body complete with louver 1400 RPM speed 230 volts AC electrical operated 50 HZ Model No. Turbo Force SP of Havells or its equivalent of Orient/ Usha/ Bajaj/CG.

Cutting, threading and the existing 25mm tubing and inserting tee for taking new branch connection from existing pipe of any of size complete all as specified and directed.

Gun metal/glove valve with iron wheel head screwed on both sides for iron pipes of 20mm internal dia complete all as specified and directed.

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

NATIONAL TRADING COMPANY

arneesh kumar suri

M/S RAHUL GUPTA