SITC of lift at alipore campus CU

SITC of new Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to relevant IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd. Before installation of new Lift, the existing old Lift installation is to be dismantled and kept in safe/proper place as per direction of E.I.C/Authority

Make : Lift manufacturers approved under category-I (as per Memorandum of PWD/Govt. of W.B vide memo no. 75-W(C)/1M-20/15 dt. 03/03/2015)

Type: Passanger Lift .

Load : 15 Passenger / 1020 Kg

Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF)

Machine:- Energy efficient machine, Gearless, without Machine Room

Position of Machine Room: MRL

Speed: 1.75 Mtrs./ Sec

Floor served: G +10

Landing: 11, all on same side

Total Rise : 34 Mtr(approx.) [subject to actual site verification]

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. COP & LOP must have stainless steel face plate silver brushed with surface mounted button. Button : All buttons on car & landing shall be luminous, on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendent mode of operation. Display type :Colour LCD / Segmented LCD/LED. Operation Push Button for lift maintenance & service should be on top of the car.

Leveling accuracy:± 5 mm(Micro levelling arrangement )

Car inside : 1600mm wide x 1500mm deep x 2200 mm height and & depth suitable for 15-Passenger Lift as per relvant NBC code or OEM standard.

Car Entrance:Clear Opening:- 1000 mm (W) x 2000 mm (H ) protected with car door or as per OEM standard.

Car Finish & Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

a) Rear Mid Panel ---- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

b) Rare corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

c) Side Mid Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

d) Side corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

e) Front Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

Car Ceiling & Lighting: Stainless Steel with hairline finish (#4) with LED lighting and Fan

Car Ventilation: Cross flow Pressure fan with anodised aluminium grill.

Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system with 2D infrared curtain of light and mechanical force limiting device,with fire rating of minimum 120 minutes.

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system, with fire rating of minimum 120 minutes.

Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room

Emergency Alarm: Battery operated alarm bell system in lift car and control room

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - As per manufacturer's standard conforming to respective applicable IS

Hand Rail:-Stainless Steel Mirror Finish Handrails on rear car panels

Auto fan cut-off

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension: 2567 mm width X 1958 mm or as per actual site condition [the Bidder should visit the site]

Available Pit Depth :1600 mm or as per actual site condition [the Bidder should visit the site]

Available Overhead : 5100 mm or as per actual site condition [the Bidder should visit the site]

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

N.B. Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish.

Please Enable Macros to View BoQ information