Special Repair work of infrastructure strengthening at various Sub Health Centres i.e Karewari, Khijarpur Jat Majra, Bohla Ganaur Sub Division for the year 2020-2021

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (b) In cement (HSR 8.5 b)

Dismantling Roofing (f) dismantling re-inforced brick or R.B/R.C work including reinforecement with cleaning and straightening and cutting of bars if required. (HSR 8.6 f)

Dismantling Roofing (g) demolishing mud phaska in tile terracing. (HSR 8.8 g)

Removing door and windows (wood and steel) with chowkats by making Recesses in walls when the wall is not to be dismantled:- (HSR 8.18 a) a) door

b) Window

Dismantling Flooring and Ceiling Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm Thick including concrete base (HSR 8.25)

Scraping White Wash & Colour Wash (HSR 8.32 a)

Scraping of Cement plaster. (HSR 8.32 c)

Cement concrete 1 : 4 : 8 with stone aggregate 20 mm Nominal size in foundation and plinth. (HSR 10.38)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in footings, strips, foundations, beams, rafts, pedestals and approach slabs of bridges etc., excluding steel reinforcement but (a)extra over Item Nos. 10.79 to 10.94, if 1:1 ½:3 mix is used, instead of 1:2:4 (10.90+10.95a)

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone aggregate 20 mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 kg per sqm laid hot and sanded. (HSR 10.114)

Providing and alying 80mm thick ISI Marked interlocking paver blocks (Conforming to ISI 156582006) IRC SP 63-2004 of all shapes and colours of design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9)

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Top khurra 0.6 m X 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50)

B Bottom khurra on ground 1.2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57)

Cement concrete 1:2:4 gola 10 cm X 10 cm quardrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Pdg. & fixing PVC rain water Pipe 6 kg Presure of ISI Mark in Cement morter during masonary work. (HSR 13.89( (a) 100mm dia PVC Pipe 6 kg presure.

Providing & fixing P.V.C Bend ISI Mark 100mm dia P.V.C Bend (HSR 13.90a)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Kotah stone flooring 34 mm to 40 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.. (HSR 14.62)

Pdg. & fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 Tile of premium quality (first quality) like NITCO, KAJARIA< SOMANI, ORIENT & JOHNSONS (HSR 14.89)

Pdg. & fixing vitrified tiles of size 600x600mm of approved make skirting dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 Tile of premium quality (first quality) like NITCO, KAJARIA< SOMANI, ORIENT & JOHNSONS (HSR 14.90)

Providing & fixing Ist quality ceramic glazed wall tiles confirming to I.S 15622 (thickness to be specified by the manufacture) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete.(HSR 14.92 b) b) Size of ceramic Glazed tiles 300x450mm

12 mm thick cement plaster 1:4 (HSR 15.5)

12 mm thick cement plaster 1:6 (HSR 15.7) (First Storey)

10 mm thick cement plaster 1:4 (HSR 15.52)

Cement pointing 1:2 deep variety on brick and Tile work (HSR 15.60)

Prepration of ply wood surface as per (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Painting two coats with synthetic enamel Paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Applying priming coat with metal primer on New steel or iron work including preparation of surface. (HSR 16.9)

Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (HSR 16.17)

Painting two coats with ready-mixed paint for metallic surfaces in all shades on old steel or iron work. (HSR 16.18)

Painting two coats on iron sheets with roofing white, grey or green ready-mixed paint on new work to give an even shade. (HSR 16.20)

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler,consisting of white lead, linseed oil, varnish and chalk mittii including finishing Preparation of plastered surfaces for oil bound distemper including sand papering (HSR 16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coat of exterior acrylic emulsion paint as per 1st quality (HSR 16.79 b)

Providing and applying two cates white cement based puty over plastered surface and grinding the durface smooth eiht sand paper to get an even and smooth finish including cost and carriage of all material, labour charge, scaffolding, sundries etc. complete (J.K/ Birla make) (HSR 16.81)

Supply & fixing hudraulic door closer I.S.I. mark, with necessary screws etc. complete ( C) ISI designation No. III (Size of door 851mm to 1000mm) (HSR 17.82 c)

Factory-manufactured wire gauze door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc, (non coniferous timber other teak, conforming to I.S. specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide locak rail 200 mm wide bottom rail and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fitting other than specified above, but including labour for fixing the same in position)- (styles and rails of windows shutter shall be 75 mm wide) (HSR 17.92 (a) (ii)

Factory manufacture solid flush door and Shutters, with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (HSR 17.93 (a) commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (i) 25 mm thick

(iii) 35 mm thick

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position.. (HSR 18.12)

Supplying and fixing rolling shutters, of approved make, M.S. laths, interlocked together through their entire length, and jointed together, t the end, by end locks mounted on specially designed pipe shaft, with brackets, side guides 27.5 cm long wire spring grade no. 2 and arrangement for inside and out-side locking with push and pull operation complete, including top cover 0.80 mm thick (payment is to be made for the exact size of opening where rolling shutter is to be fixed):- (HSR 18.18) (a) with 80 mm X 1.00 mm M.S. Laths

Providing and fixing in positon collapsible steel shutters, with vertical channels 20 mm X 10 mm X 2 m and braced with flat iron diagonal 20 mm X 5 mm size, with top and bottom rails of T-iron 40 mm X 40 mm X 6 mm with 38 mm dia steel pulleys, complete with bolts, nuts locking arrangements, stoppers, handles, etc., complete

Fe-500 EQR TMTsteel bar for RCC work, where not included in the complete rate of RCC including bending, binding & placing in the position complete. (NS). (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make (HSR 18.30) (b) glass panes 4 mm thick, exceeding 40 sq dm areas.

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- (HSR 18.34 b) b) door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate

(d) door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate

Pdg. & fixing of standard circular Logo tiles of HWC acitivities of size 3 feet dia i/c cost of adhesive (NS)

Pdg. & fixing of 6x3 feet standard circular Logo of Ayushman Bharat HWC as approved by Health Deptt. I/c cost of adhesive consisting of 3 nos. tiles of size 3'x3' (NS)

Pdg. & fixing of design with 4'x9' border tiles printed as per norms / design of HWC i/c fixing with adhesive of good quality (NS)

Earth Filling in the SHC Campus with an avg. led of 8 km.

Recovery The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :-(Good Tiles @ 2.50/- each)

Tile Bats @ 400 per cum)

Scrap of Steel @ 2500 per Qtl

Door & Windwo @ 550 per Qtl) Note: All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be not measurement after actual scarifying and if material after scarifying is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

M/s Ahmed Builders