Providing Lift Irrigation Scheme from River Beas to Pali and Silag in Tehsil Padhar Distt Mandi HP

Amount

Cutting in earth work and disposal of excavated earth upto a lead of 20 metres in pick work 50% and jumper work 50% in all leads and lifts.

Excavation in foundation and trenches etc. in earth work in all kind of soil such as pick work jumper work,saturated soil including bailing or pumping out water, blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting,timbering and dewatering where ever required as per the direction of the Engineer-in-Charge.

Providing and laying cement concrete 1: 6 : 12 (1 Cement : 6 Sand :12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts.

Providing and laying cement concrete 1: 3 : 6 (1Cement : 3 Sand : 6 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts.

Providing and laying cement concrete 1: 3 : 6 (1Cement : 3 Sand : 6 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts.

Providing and laying cement concrete 1: 2 : 4 (M: 30)(1Cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation ,footings & Buttresses etc. with in all leads and lifts.

In foundation ,footings & Buttresses etc. with in all leads and lifts.

Columns,pillars,posts and struts upto floor to level.

Square,rectangular or polygonal; in plan in all leads and lifts.

Circular in plan in all leads and lifts.

Walls (any thickness but not less than 0.1 mtrs thickness) attached pillasters, buttresses, plinth and string courses etc. from top of foundation level upto floor to level, in vertical walls and columns etc.in all leads and lifts.

In suspended floors, roofs, landings and shelves and their supports, balconies, beems, girders, bressumers and cantilivers upto floor to level in all leads and lifts.

Providing and laying cement concrete 1 : 1½ : 3 (M: 20) (1Cement : 1½ Sand : 3 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in:

Foundations, footings, basis of columns & the like and mass concrete with in all leads and lifts as per the direction of Engineer-in-Charge.

Wall (any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level with in all leads and lifts.

In suspended floors such as .roofs,slabs landings etc. in all leads and lifts

Random rubble masonry/ polygonal rubble masonry(uncoursed/brought to courses) in walls with hard stone of apporved quailty in foundation & plinth including levelling up with cement concrete 1:6:12(1Cement :6 sand :12 graded stone aggregate 20 mm nominal size) in cement mortar 1:6 (1 Cement : 6 Sand) with in all leads and lifts.

Stone / Boulder filling under floor within all leads and lifts.

Providing tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level with in all leads and lifts.

Providing and laying cement concrete 1:5:10 (1Cement : 5 Sand : 10 graded stone aggregate 40 mm nominla size) with 15% plum and curing complete excluding cost of form work in retaining wall, the size of plum shall usually be 150 mm to 300 mm as per HPPWD specification with all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish i/c centring , shuttering , strutting and propping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4mtr and removal of the same for insitu- reinforced concrete & plain concrete work in :-

In foundation, footings & Buttresses etc. in all leads and lifts

Flat surfaces such as soffits of suspended floors , roofs,landings and the like up to 200mm in thickness with in all leads and lifts.

Vertical surfaces such as walls (any thickness), partitions and the like including attached pillasters, buttresses,plinth and string courses and the like with in all leads and lifts.

Columns,pillars,posts and struts.

Square,rectangular or polygonal; in plan in all leads and lifts.

Circular in plan in all leads and lifts.

Beams,cantilivers,girders and lintels sides and soffits of beams,beam haunchings,cantilivers,girders,bressumers and lintels not exceeding 1 metre in depth in all leads and lifts

Edges of slab and breaks in floors and walls under 20 cm wide in all leads and lifts.

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 ( 1 Cement : 6 Sand ) second class bricks with in all leads and lifts.

Half brick masonry in common brunt clay building bricks in cement mortar 1 :4 ( 1 Cement : 4 Sand ) second class bricks with in all leads and lifts.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jump lock jamb, beed and if required angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel but things 2.5 mm thick with gaurds, lock strike plate and shock as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by Engineer-in-charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood with in all leads and lifts.

Providing & fixing M.S. grills of required pattern in wooden frames of window etc. with M.S. flats square or round bars with round headed bolts and nuts or by screws plain grills with in all leads and lifts.

Cement concrete flooring 1:2:4 (1Cement : 2 Sand :4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement 40mm thick with in all leads and lifts.

6mm cement plaster to ceiling in cement mortar 1 : 3 (1 Cement :3 Sand) with in all leads and lifts.

15 mm cement plaster in single coat on rough side of brick/ concrete / stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1 : 6 (1 Cement :6 Sand) with in all leads and lifts.

Raised and cut pointing on brick work with cement mortar 1 : 3 (1 Cement : 3 Sand) with in all leads and lifts.

White washing with lime on un-decorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar dirt and other foreign matter with in all leads and lifts.

Distempering (Two coats) with oil bound washable distemper of approved brand and of manufacturer and of required shade on undecorated wall surface to give an even shade over and including priming coat with distemper primer of approved brand and manufacturer after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth. Primer coat with distemper primer with in all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt,and other foreign matter , sand papering and knotting ready mixed paint brushing wood primer pink with in all leads and lifts.

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces, with enamel paint to give even shade including cleaning the surface of dirt, dust and other foreign matter, sand preparing and stopping with enamel paint other than white with in all leads and lifts.

Providing and fixing anodized M.S. sliding door bolts with nuts and screws etc. and necessary screws etc. complete with in all leads and lifts. 300x16 mm.

Providing and fixing anodized M.S, Tower bolts (Barrel type) with necessary screws etc.complete with in all leads and lifts.

250 mm x10 mm.

150 mm x 10 mm.

Providing and fixing anodized MS handles with necessary screws etc. complete with in all leads and lifts

Providing and fixing oxidized M.S. hooks and eyes 250 mm complete with in all leads and lifts.

Prividing plinth protection 50 mm thick in cement concrete 1:3:6 ( 1cement : 3sand : 6graded strone aggregate 20mm nominal size) including finishing the top surface of concrete smooth with in all leads and lifts.

Proving under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick / stone Aggregate 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground.

White glazed tiles 6 mm thick in flooring cement mortar 1 : 3 ( 1 Cement : 3 Sand) finished with flush pointing in white cement with in all leads and lifts.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1 : 3 ( 1 Cement : 3 Sand) and jointed with cement slurry with in all leads and lifts.

Steel work welded in built up sections,trusses and framed work including cutting,hoisting, fixing in position and applying a priming coat of red lead paint in all leads and lifts.

In gratting,framed guard bar,ladders,railingbrackets and similar works.

In trusses and trussed purlins in building in all leads and lifts.

Providing and Fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster 5 microns primer coating icluding fixing with prepainted iron J or L hooks, bolts and nuts 6mm diametre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-In-Charge.

Providing ridges or hips 60 cm over all in plain with galvanised iron G.I Sheet fixed J or L hooks bolts and nuts 8mm dia G.I Limpet and bitumen washers complete 0.60 mm thick sheet.

Providing and fixing 15 cm wide 45 cm over all semicircular with iron plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connection with rain water pipe complete as per design in all leads and lifts.0.80 mm thick sheet.

Providing and Fixing INDEF/POWERFULL make Power Operated Gantry of 1.0 MT capacity complete in all respects(with all allied accessories) to the satisfaction of Engineer-in Charge. The clear span of gantry girder shall be 6.00 m. The gantry shall be capable of moving Longitudinally and transversally to any location of pump house having internal dimensions as 17.70 m x 6.00 m

Laying, Jointing, Testing & Carriage of G.I. pipes (light grade) tube fittings in trenches for inlet/outlet pipe/overflow pipe excluding earth work complete with all leads & lifts.

100 mm dia

Providing and Fixing double flange cast iron Sluice Valve of 100mm dia.(Single ball type)of Leader/Kirloskar/Kartar make conforming to BS 780-1984 with upto date amendments as per class PN 1.00 to with stand a seat pressure of 10.20 kg/cm2

100 mm dia. Flange Table=5 ,class PN-1.00

1.20 metre heigh fencing (as per approved design) 1.80 metres R.C.C.posts 3 metres centre to centre and R.C.C. struts with 7 horizental lines and two diagonals of galvanised steel bar bed wire (IS 278-1962 type I) weighing 9.38 kg./100 metres (minimum) strained and fixed to posts by typing to 6mm galvanised steel bar niles/clips with G.I. binding wire including cost of Excavation, R.C.C. Posts,R.C.C. struts and straining belts and embeded in cement concrete 1:4:8 ( 1cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete in all respect and to the entire satisfaction of the Engineer-in-Charge.

Providing and Fixing tube settler media of PVC material complete with all leads and lifts upto the satisfaction of Engineer-in- Charge

Providing and fixing of 150 mm dia. control valve for pipe orifice at outlet of raw water channel including all necessary fittings & accessories complete in all leads and lifts upto entire satisfaction of Engineer-in- Charge.

Providing and fixing of 250 mm dia. control valve for sludge line exit at sludge chamber including all necessary fittings & accessories complete in all leads and lifts upto entire satisfaction of Engineer- in- Charge.

Providing and fixing of 500 mm dia. C.I. manhole cover complete with all necessary accessories in all leads and lifts upto the satisfaction of Engineer-in- Charge.

Providing and Laying HDPE pipe complete with all necessary fittings & accessories in all leads and lifts upto the entire satisfaction of Engineer-in-Charge.

250 mm dia.,PN 4.0 PE 80/100

280 mm dia.,PN 4.0 PE 80/100

315 mm dia.,PN 4.0 PE 80/100

400 mm dia.,PN 4.0 PE 80/100

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 4.00 Sq. mm.

Supplying and fixing 3 pin 5/6 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 2 way 5/6 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing 3 pin 15/16 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 15/16 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing wooden box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required.

229 mm.x 102 mm.x 60 mm. deep

203 mm.x152 mm.x 60 mm. deep

Supplying and fixing ceiling rose on existing junction box/ wooden block including connections etc. as required.

Supplying and fixing plain pandent with 16/20 mm twin twisted, flexible PVC insulated copper cable and backelite pendant holder including connections, etc. as required.

Supplying and Fixing 5 Amps to 32 Amps rating, 240 Volts, L series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required Cat - A. (Single Pole)

Supplying and Fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 Volts on surface/ recess, complete with tinned copper busbar, netural link, earthbar, dibnbar, detachable gland plates, inter connections, i/c painting, earthing etc. as required busbar 8 way.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (63 amp. CAT - A)

Providing, installing, testing and commissioning of ceiling fan and regulator i/c wiring the down rod of standard length (upto 30 Cm with 1.5 Sqmm PVC insulated copper conductor signle core cable etc. as required.Ceiling fan 1400 mm sweep category A

Providing and fixing ultra slim decorative extruded box fixture with domestic electronic ballast, snap-on installers, suitable for 28 watt FTL (T5), complete with all accessories (including one No. T-5 Tube), connections, testing and commissioning etc. as required.

1 x28 watt-FTL (T5) (Category-A)

Providing and Fixing LED Street Light made up of mentioned below pressure die cast aluminium housing with high power LED as lighting source and lens embended PC cover having TOP opening separate driver compartment with IP-66 and compact resistance of IK07 make ENDURE PEARL NEO SL 40 WLED 757 PASYTOPC suitable for pole dia 43 mm maximum complete in all respect in all leads and lifts.

Providing and fixing two core service wire 6 Sqmm thick in all leads and lifts.

Gaurav Thakur