Pdg. 1 Nos. Additional 12.5 Mtr. High Mast Tower with LED fittings in Boys Hostel of Shri Krishna Ayush University (SKAU), Distt. Kurukshetra (Recall).

Amount

Supply and erection of miniature circuit Breaker /isolator 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCB's TRIPLE POLE HSR No. 23.22.5.6

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 4 way ( 2 incoming and 2 outgoing) HSR No. 23.22.4.1

Supply and election of Goodridge Almirante type MS pedestal made of 50 mm *50 mm * 6 mm angle Iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and looking arrangement with the Godrich type handle including round bars. The to covering should have a downward overhang of 75 mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four No’s. holes to discharge the heat produced by suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embedded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work. M.S. pedestal of size 600 mm wide, 750 mm high, 300 mm deep and bottom totally open , duly embedded in cement concrete block of size 900 mm*450 mm*200 mm above ground level , having a base of size 900 mm* 600 mm* 250 mm below ground level. HSR No. 23.27.1

EARTHING AND LIGHTENING ARRESTOR Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. HSR No. 24.1.1

Extra for using salt and char coal/coke for pipe earth electrode as required. HSR No. 24.1.2

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop carthing as required. HSR No. 24.1.13

B.S.E.N. 10025 High Masts Supply, installation, testing and commissioning of 12.5 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip , galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 no’s. luminarie loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 no’s steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete I all respect upto entire satisfaction of Engineer-in Charge. Thickness of Top and Bottom Section = 3 mm (minimum). Top Dia = 150 mm and Bottom Dia = 360 mm. Thickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum) HSR No. 24.4.15.2

RCC foundation for HIGH MAST Octagonal Poles Providing RCC foundation of M25 grade (1 cement 1 stone aggregate 2 coarsesand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10of required dimensions for high mast octagonal poles of various heights as per following specification complete in all respect and as per directions of Engineer-in-charges. 12.5 Mtr High Mast Pole HSR No. 24.9.1

S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Mtr below ground level including diging and refilling of earth including cost of suitable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia HSR No. 24.5.2.4

WIRE Only 1.5 sq. mm ISI marked, FRLS PVC insulated, single core copper conductor cable EL003

4.0 sq. mm ISI marked, FRLS PVC insulated, single core copper conductor cable EL005

Supply and erection of 200 watt LED Flood light (Make : Havells) JETA VALOURFL200WLED757PINTNBLT G ( Jeta valour Integral Energy saving, environment friendly, long life, exclusive innovative die-cast aluminium flood light with highly efficient LEDs as light source, suitable for highlighting architectural features or retail spaces with accessories required to complete the job in all respect upto the entire satisfaction of Engineer in Charge of the work and equivalent make Phillips, Crompton & Bajaj. NS- 1

Supply and erection of 16 Sqmm 4Core Cable, Grandlay make, armd cable PVC/XLPE insulated ( Heavy Duty) Electrical Cables for working voltage upto and including 1100 Volts to IS:1554 (PART-I) with Aluminium conductor-ISI marked Power Cable - Aluminium Conductor (Make : Grandlay, Polycab, Plaza). NS- 2

Som Nath Contractor

Choudhary Electricals

MS Tiger Solar Light Trading Co.