The Construction of New Section Office at Kapura ,Ta-Vyara,Di-Tapi.

Excavation for foundation upto 1.5 m depth

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter

lead. (A)Loose or soft soil.

Excavation for foundation for depth from 1.5 m to

3.0 m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

50 Meter lead.(B) Dense or Hard soil.

Filling available excavated earth (excluding rock) in

trenches. plinth, etc. in layers not exceeding 20 cm.

in depth consolidating each disposited layer by

ramming and watering.

Filling in plinth with sand under floors including

5 watering, ramming, consolidating and dressing etc. 22.15 Cmt 471.690

Filling in foundation and plinth with murrum or

6 selected soil in layers of 20 cm. thickness including 44.30 Cmt 296.290

watering, ramming and consolidating etc. Complete.

Providing and laying controlled cement concrete

M.150 for curing complete excluding cost of

7 formwork and reinforcement for reinforced 12.42 Cmt 4007.510

concrete work in (A) Foundations, footings,Base of

columns and Mass concrete.

Carring out plinth treatment to post construction /

existing structure by spraying chemical solution for

termite control treatment including labour and

material consistment with I.S.I specification. Using

Chlordene and Chiorpurfiles 20 EC.As Per

8 6131_paret-II Consentration Weight one percent is 177.56 Smt 83.490

recommended i.e one litre 20 EC chemical emulsion

with 19 liter give 1 % concrentration inclusive of one

litre chemical emulsion appication at the rate of

Litre chemical / Sqm of surface is recommended as

Providing and laying controlled cement concrete

M.250 and curing complete excluding the cost of

formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings, Base of

columns and Mass concrete.

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. Height of

propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same

for in situ reinforced concrete and plain concrete

work in. (A) Foundations Footings Bases of Columns

etc. and Mass concrete.

M25 - Providing and laying controlled cement

concrete M.250 and curing complete excluding the

11 cost of formwork and reinforcement for reinforced 5.14 Cmt 4755.850

concrete work in (D) Columns, Pillars posts and

struts, upto floor two level.

M25 - Providing and laying controlled cement

concrete M.250 and curing complete excluding the

cost of formwork and reinforcement for reinforced

concrete work in (C) Slabs,landing,shelves,Balconies,

Lintels, Beams, Girders and Cantilever upto floor

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. height of

propping and centering below supporting floor to

13 ceiling not exceeding 4 M. and removal of the same 319.33 Smt 202.180

for in situ reinforced concrete and plain concrete

work in. (H) (1) Sides and soffits of Beams Beam

Haunchings cantilevers Girders Bressumers and

Lintels not exceeding 1 M. in Depth.

M20 - Column Providing and laying controlled

cement concrete M.200 and curing complete

excluding the cost of formwork and reinforcement

for reinforced concrete work in (D) Columns, Pillars

posts and struts upto floor two level.

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. height of

propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same

for in situ reinforced concrete and plain concrete

work in. (G) Columns PillarsPosts and struts. (1)

Square Rectangular Polygonal in plan. (upto 10 ton).

M20 - Stair case Providing and laying controlled

cement concrete M.200 and curing complete

excluding the cost of formwork and reinforcement

for reinforced concrete work in (E) Staircases

excluding landing upto floor two level.

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. height of

propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same

for in situ reinforced concrete and plain concrete

work in. (M) Staircase with sloping or stepped soffits

including risers and stringers excluding landing.

M20 - Landing, Beam, Slab, Chhajja, Lintel/coping

Providing and laying controlled cement concrete

M.200 and curing complete excluding the cost of

18 formwork and reinforcement for reinforced 62.53 Cmt 4617.590

concrete work in (C) Slabs, landing, shelves,

Balconies, Lintels, Beams, Girders and Cantilever

upto floor two level.

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. Height of

propping and centering below supporting floor to

19 ceiling not exceeding 4 M. and removal of the same 233.97 Smt 260.880

for in situ reinforced concrete and plain concrete

work in. (B) Flat surfaces such as soffits of

supspened floors slabs Landings and the like. (1)

Floors etc. upto 200 mm in thickness. (upto 10 ton).

Providing TMT Bar FE 500D reinforcement for

R.C.C. work including bending, binding and placing in

position complete upto floor two level (more than

Full Brick work using common burnt clay building

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

21 Mortar 1:5. (1- Cement : 5 - fine sand) (B) 58.61 Cmt 4194.570

Conventional . Extra for brick work in superstructure

above plinth level upto floor two level (B)

Half brick masonry in common brunt clay building

bricks having crushing strength not less than

22 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 - 86.33 Smt 614.840

coarse sand ) in foundation and plinth (B)

Providing & applying 15mm thick Mala plaster on

walls consisting of 12mm thick backing coat of C.M.

1:4 (1 cement : 4 sand ) and 3mm thick finishing coat

of C.M. 1:1 (1 cement : 1 sand) including curing,

necessary scaffolding in true line & level etc. comp.

as directed by Engineer in charge

20mm thick sand faced cement plaster on walls

upto height 10 metres above ground level consisting

24 of 12mm thick backing coat of C.M. 1:3 (1-cement : 765.91 Smt 337.520

3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-

cement : 1-sand) etc. complete.

Providing & laying 24" x 24" vitrified 8 mm thick tile

flooring over 20 mm (average) base of cement

mortar 1:6 ( 1 cement: 6 coarse sand) on new

surface or fixing on existing flooring by adhesive

material including dismentaling of existing flooring

and jointed with color cement slurry including

finised with flush pointing & cleaning the surface

etc. complete for light shade .

Providing and laying Vitrified tiles 8 to10mm thick,

24" x 24" vitrified' in flooring treads of steps

26 skirting and landing laid on a bed of 12mm thick 71.11 Smt 1099.950

cement mortar 1:3 (1-cement:3-coarses and)

finishing with flush pointing in white cement.

Providing and fixing polished Black grenite slab(18

to 20 mm thick) for Door and Windoow Framing as

directed by Architect/ engineer-in-charge. (upto

Providing and fixing flush door shutters, solid core

construction with frame of first class hardwood with

cross board and face veneer or plywood face panels,

28 including anodised alluminium butt hinges with 18.28 Smt 1829.740

necessary screws. (B) Non-decorative type and block

board core anodised alluminium butt hinges in flush

door shutters (2) 35 mm thick.

Providing and fixing M.S. grills of required pattern

to wooden frames of windows etc. with M.S. flats at

29 required spacings and frame alround, square or 491.90 Kg. 106.480

round bars with round headed bolts and nuts or by

screws (A) Plain Grill.

Applying priming coat over new steel and other

metal surface after and including preparing the

surface by throughly cleaning , oil , gresse , dirt and

other foreign matter and sourced with brushes fine

steel wood scrapes and sand paper with ready

mixed priming paint brushing red lead.

Painting two coat (excluding priming coat ) on new

steel and other metal surfaces with enamel paint

brushing to give an even shade including cleaning

the surface of all dirt, dust and other foreign matter.

Providing and fixing extruded aluminum window

having extruded aluminum Colour Powder Coated

section frame main outer size 127mm x 38.10mm x

1.35mm (of Jindal Section no:2443,@ Wt.1.384

Kg/mt),horizontal Four track member size

122.20mm x 31.75mm x 1.10mm (of Jindal Section

no:8787,@ Wt. 1.205 Kg/mt), vertical member of

size 122.20mm x 31.75mm x 1.50mm (of Jindal

Section no:8935,@ Wt. 1.398 Kg/mt) with sliding

shutters of horizontal member size 40mm x 18mm x

1.29mm (of Jindal Section no:8949 @ wt.of

0.456Kg/mt),vertical member of size 40mm x 18mm

x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/Section 8948,@ Wt. 0.457 Kg/mt) with

5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and

fixtures and transparent silicon sealant glass fixing

toframe as per details etc complete for window.

Applying two coats of Birla (white cement based) or

Asian (acrylic lapy- putty) or equivalent & two coats

of primer of approved brand and manufacture on

33 new wall surface to give an even shade including 567.38 Smt. 40.590

thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand

papered smooth.)

Wall painting (two coats) with plastic emulsion

paint of approved brand and manufacture on

undercoated wall surface to give an even shade

including throughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth.

Finishing wall with weather proof exterior emulsion

paint on wall surface (two coats) to give an required

35 shape even shade after thoroughly brushing the 765.91 Smt 117.400

surface to remove all dirt, and remains of loose

powdered materials.etc complete.

Applying primer coat over wall surface (One coats)

to give an required shape even shade after

36 thoroughly brushing the surface to remove all dirt, 351.22 Smt 80.800

and remains of loose powdered materials.etc

Providing and laying waterproofing treatment on

terrace including (a) applying neat cement slurry

2.75 kg/sq.mt. of cement admixed with water

proofing compound after cleaning the surface (b)

laying cement concrete using brick bats 25 to

mm size with 50% cum 1:5 (1cement : 5 coarse

37 sand) and admixed with water proofing compound 235.74 Smt 1666.500

over 20 mm thick layer of CM 1:5 to required slope

including rounding of junction of walls and slab (c )

After two days of proper curing applying a second

coat of cement slurry (d) after finishing the whole

terrace shall be flooded with water for a period of

Providing & laying broken china mosaic flooring for

terrece using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 plain

or slope and to be tempered to bring mortar crème

out up to suface using white cemenrt including

rounding off junction and extending them up to

cm along the wall cleaning with water and oxlic acid

etc as directed.

Providing and fixing standard extruded of

alluminium section of size 63mm x 38.10mm x

1.2mm (Jindal section : 2434, @Wt. 0.643 kg/m)

with colour powder coated alluminium frame for

ventilation with 5mm thick frosted glass as details

etc complete for ventilation.

Providing & fixing S115M (BS) - Steel Mortice

Handles, KY Small, Finish Black Silver, Door Thickness

30-45 MM, Metal Steel. RML4 - KY Mortice Locks,

40 Metal Steel / Zinc, Size 65 MM, Door Thickness 30- 10.00 Nos. 3030.000

45 MM, 4 Steel Lever, Finish Electro Coated Body &

CP Cram, Durable and Long Life, Good Quality

Mortice Lock Set From Renowned Brand Sprider.

Providing 0.75mt wide plinth protection including

excavation in hard or dence soil and Laying C.C 1:3:6

41 (1 cement : 3 coarse sand: 6 brickbats/stone 17.07 Cmt. 989.800

aggregates) in foundation and on top including

Curring fnishng etc. complete.

Providing & fixing in position S.S. hand rail in main

stair case, landing, balconies etc. in 2" (50mm) dia

S.S. Pipe 1.5 mm thk. 304 grade resting on 1" (25

mm) S.S. pipe 1.5 mm thk. 304 grade size S.S.

grade square bars 10 mm, of clear height 1 meter

placed at 30 cm c/c including making necessary hold

fast fixture (10 mm square bars 22 cm long)

embedded in staircase concrete for resting the S.S.

304 grade. vertical square bard with holding etc. as

per approved design and as required for the work

including bending hand rail pipe to proper shape in

curves with specials etc. complete (Approved Makes

- Tata/SAIL/Jindal/Essar/Bhushan Steel/Arecelor

Mittal). Railing height is 1 M.

Entrance Door Providing and fixing solid core 35mm

thick double door Shutters including indian teak

wood frame size 12 cm X 7 cm size , both side

polished and fastening including 2 coats of

melamine polished also including hardwares All

hardwares from Dorma-XL-C like both side handle

hinges , tower bolt etc.all in S.S. based complete.

fully panelled all item as per approved by architects.

Providing and fixing water closet squatting Pan

(ORISSA PAN) approved make like

44 cera/jaquar/Simpolo/Hindware or equvalent to 1.00 Each 2020.000

same of size 450*585*255mm (I) Long pattern =

White colour.(MR)

Providing and fixing Wall Hung-WC with PP normal

closet seat cover, hinges, accessories set approved

make like cera/jaquar/Simpolo/Hindware or

45 equvalent to same of size 370*535*405mm with 2.00 Each 3838.000

integral P or S trap including jointing the trap with

soil pipe in Cement Mortar 1:1 (1-Cement : 1- fine

sand) (i) in white colour(MR)

Providing and fixing Hand shower (Health Faucet)

with 8mm dia 1.2 meter long flexible tube and wall

46 hook of approved make like 2.00 Each 1515.000

cera/jaquar/Simpolo/Hindware or equvalent to

Providing and Fixing 100 mm size P or S trap for

water closet squatting pan including jointing the

trap with the pan and soil pipe in cement Mortar 1:1

(1 cement : 1- fine sand) (A) vitreous china.

Providing and fixing Urinal or approved quality

including conecting the Urinal with waste pipe

,Down tap etc. complete.approved make like

cera/jaquar/Simpolo/Hindware or equvalent to (A)

White earthenware flat back or corner type size

Providing and Fixing plastic seat and cover for wash

down water closer with C.P. brass hinges and rubber

buffers. (B) black plastic seat and cover.

Providing and fixing wall hung basin with fixing

accessories set with single hole for pillar tap

approved make like cera/jaquar/Simpolo/Hindware

or equvalent to same of size 550*400*195mm In

white colour.(MR)

Providing and fixing screw down bib taps of

51 following size.(B) Brass chromium plated screws 4.00 Each 186.830

down Bib Tap. (i) 15mm dia.

Providing and fixing chromium plated brass half trun

52 flush cock of approved quality including fixing in 3.00 Each 263.770

pipe line etc. complete.(ii) 25mm dia.

Providing and fixing C.P. brass waste for washbasin

or sink. (A) 32mmdia.

Providing and fixing M.I. fisher union for washbasin

or sink. (B) 40 mm dia.

Drainage Providing, laying and jointing in true line

and level 110 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to

ISI 14735- 1999 of approved make for drainage

system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on

wall using of PVC clamp of the size 110 mm

diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in

walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials.

Providing, laying and jointing in true line and level

75 mm diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to

ISI 14735- 1999 of approved make for drainage

56 system pipe line, pipe shall be jointed with each 11.00 Rmt 324.510

other with rubber lubricant, pipe shall be fixed on

wall using of PVC clamp of the size 110 mm

diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in

walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials. (RA)

Water SupplyProviding and fixing concealed center

point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for

potable water of following dia. nominal bore tube

fittings and clamps including making good the wall,

ceiling and floor etc. complete. [A] 15 mm.

(B)20mm nominal outer dia pipes

(C)25 mm nominal outer dia pipes

(D)32mm nominal outer dia pipes

Providing and fixing brass screw down stop tap. (A)

58 15mm dia. (Urinal) 3.00 Each 205.830

Providing and fixing ball cock of approved quality as

59 directed. (A) Copper Metal (ii) 50mm dia. 3.00 Each 189.840

Providing and fixing chromium plated brass half trun

60 flush cock of approved quality including fixing in 3.00 Each 275.760

pipe line etc. complete.(iii) 32mm dia.

Providing and fixing Gun metal check or non-return

61 fullway wheel valve.(D) 32mm dia. 2.00 Each 314.730

Providing erecting and fixing double coated Syntex

PVC. (ISI) water tank of required capacity each with

62 all necessary fittings and connection etc. complete 2000.00 Ltr. 3.950

Providing and fixing S.W. gully trap with C.I. grating

brick masonry chamber and water tight C.I. cover

with frame of 300mm x 300mm size (inside) with

standard weight.(i) Square mouth traps. (A) 100mm

x 100mm size P type. (upto 10 ton)

Water SupplyConstructing brick masonry chamber

for underground C.I. Inspection chamber and bends

with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

64 top slabe with 1:2:4 mix (1-cement :2- coarse sand 3.00 NOS 3660.760

:4-graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(ii) Inside dimensions 500mm x 700 mm

and 450mm deep for pipe line with one or two

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty nonpressure pipes

I.S. class NP2 of the following internal diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(C) 250mm dia

Box cutting the road surface to proper slope and

camber for making a base for road work including

66 removing the excavated stuff and depositing on the 43.20 Cu.mt. 106.650

road side slope as directed up to 50 m.lead

Construction of Granular sub-base 150 mm thick by

providing coarse graded machine crushed

B.T.material satisfying MOST specification of grading

I (B.T.stone aggregate 53 mm to 26.5 mm 35%,26.5

to 4.75 mm-45% and 2.36 mm below-20%)

including spreading in uniform layer with motor

grader on prepared surface,mixing by mix in place

method with rotavator at OMC and compacting with

vibratory roller to achive the desired density

M-200 Providing & Laying Controlled cement

concrete M-20 and curing complete excluding the

68 cost of form work and Excluding reinforcement 43.20 Cu.mt. 4098.940

(Footing) for road

Labour charges for giving Trimix treatment to

Concrete surface including necessary steel channel

formwork and required tools and machinery

including preparing joint with concrete cutter

machine as required and directed.

Providing and laying controlled cement concrete

M.200 and curing complete excluding the cost of

formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings, Base of

columns and Mass concrete (upto 10 ton).

Providing formwork of ordinary timber planking so

as to give a rough finish including centering

shuttering strutting and propping etc. Height of

propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same

for in situ reinforced concrete and plain concrete

work in. (A) Foundations Footings Bases of Columns

etc. and Mass concrete. (upto 10 ton)

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:5. (1-

Cement : 5 - fine sand) (B) Conventional (upto

ton). Extra for brick work in superstructure above

plinth level upto floor two level (B) Conventional

Point wiring for Light / Bell with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch /

bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

Cat. III 44.00 Pt. 485.810

Point wiring for FAN with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME four

or more step type electronic fan regulator with

74 separately mounted and accessories with earth

continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector

(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

Cat. III 6.00 Pt. 674.680

Point wiring for secondary light point with 2-1.5

sq.mm & earth wire of 1.5 sq.mm (green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires, in below type of pipe to be

erected complete with earth continuity and

75 necessary connection with primary light with

accessories erected on Metal / PVC / wooden box

covered with 3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as

(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling 30.00 Pt. 167.660

Point wiring for on board Looped Plug with 6A

Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with

following type accessories

Cat. III 26.00 Pt. 257.550

Providing following type of Modular Type

Accessories mounted with PVC / metallic/Wooden

box, single mounting base frame covered with

textured / metallic/white front plate , modules

erected with necessary connections as per site

situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket [A] For One

Cat.III 4.00 Ea. 160.590

77.b (7) Blank Plate Single

Cat.III 21.00 Ea. 25.250

77.c (8) Computer RJ-45 socket

Cat.III 8.00 Ea. 160.590

77.d (9) 16 Amp. SP one way switch

Cat.III 8.00 Ea. 180.790

77.e (10) 6/16Amp. Universal socket

Cat.III 5.00 Ea. 199.980

77.f (15) 32 Amps. DP switch with Indicator

Cat.III 1.00 Ea. 280.780

Decorative call bell Ting-tong box type 250 volts

complete erected

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in

approved manner as directed

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

80 erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

(E) in existing pipe

(b) 2 wire 2.5 sq. mm 125.00 Mtr. 62.620

Providing and erecting Mains with 1.1 KV grade

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size

(E) in existing pipe

81.a (a) 2 wire 4 sq. mm 75.00 Mtr. 86.860

81.b (b) 2 wire 6 sq. mm 85.00 Mtr. 121.200

Providing and erecting Mains with ISI marked, 1.5KV

82 grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe

of following size (Specifically for control panel,

relays, power switchgears, motor starters & control

wiring) with required size of copper lugs, nuts and

bolts if required.

82.a (e) One wire 6.00 sq. mm 85.00 Mtr. 56.560

82.b (f) One wire 10.00 sq. mm 55.00 91.910

Supplying & erecting approved make Telephone

Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer Jacket

83 suitable for telephone wiring & confirming to C-DOT 125.00 Mtr. 20.200

erected in existing pipe. of following size of

conductors & nos.of pairs. With necessary

connections. [A] Conductor Size 0.5 mm (a)

Unarmoured 2) Two Pairs

83.a (b) Armoured [Jelly Filled] 2) Twenty Pairs 15.00 Mtr. 199.980

Providing & erecting main Distribution (MDF) indoor

84 type, back mounted frame as per DoT standard 1.00 Ea. 1747.300

approved with krone strips (c) Suitable for 50 pair

Supplying & erecting approved make LAN cable of

85 following size in existing pipe as per direction [D] 55.00 Mtr. 76.760

Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and

high U.V. & corrosion resistance with diffuser with

company mark/name 120 to 300 V,Power Factor

more than 0.9, THD < 15 %,CCT 3000 K to 6500K,

86 Luminaire efficacy> 85 lumens/watt ,LED efficiency-

110 lumens/watt LED driver efficiency > 85 %CREE /

OSRAM / PHILIPS Lumileds / NICHIA /

SEOUL/Bridgelux make LED used for luminaire. (

fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

(A) Square/ Circular shaped Surface/Recessed

86.a Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 KV

Cat-III 10.00 Ea. 758.510

(B) LED Panel Light with provision for Plane front

86.b frame with translucent cover fixed to housing

complete.IP20 (e) 24 watts, 12" x 12" , Surge-2 KV

Cat-III 8.00 Ea. 724.170

Providing and erecting Approved make Ceiling fan

with double ball bearing ISI mark with condenser

A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy

erected on existing hook or clamp with earthing.

[Make shall be approved by Engineer in charge]

Supplying and erecting 19 / 20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly

painted for fan complete with proper insulation

without leakage and earthing.

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm

89 length each side and pierced through a 16 Gauge 6.00 Ea. 108.070

M.S. box / Heavy Duty PVC box complete erected

concealed in Ceiling with necessary finishing.

Supplying & erecting approved make low noise

decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame. 250mm

with 1350 RPM Cat.II

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor

91 for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of

91.a (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) 25.00 Mtr. 284.820

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Providing and, fixing heavy duty flange type brass

double compression type cable gland with rubber

92 ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following

size of cables.

Solder less crimping type Aluminium lugs

conforming to IS suitable for cable of following size

93 evenly crimped with high pressure tool & connected

to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner.

Making trench in soft soil of suitable width of 90 cm

deep for laying cable or locating the fault all over

the run and back filling the same and making the

surface as normal ground.

Providing & laying approved make Double walled

corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

95 necessary connecting accessories of same material 15.00 Mtr. 95.950

at required depth in existing trench for laying of

cable. below ground / road surface for enclosing

cable (C))90 mm outer dia

Providing and erecting Miniature circuit breaker

single pole 6A to 25A suitable to operate on 240 V

A.C. system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS

8828/1996 with ISI Mark

Cat.III 5.00 Ea. 112.110

Providing & erecting 240 V MCB double pole switch

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box

having following capacity

Cat.III 10.00 Ea. 295.930

Providing and erecting Approved make ELCBs /

RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on

single phase 240 V,50Hz. having characteristic of

quick action & tripping with all advance feature & do

not incorporate any electronic component. for

following Max. rating erected as directed

(ii) 40Amps. DP

Cat. III 1.00 Ea. 2235.130

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box

having following capacity

Cat.III 1.00 Ea. 638.320

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal

100 current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C.

supply 50 c/s. with all internal connections &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III 1.00 Ea. 6173.120

providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal

101 current rating 125A. with Fixed thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with

all internal connections & complete erected in

existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III 1.00 Ea. 8055.760

providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

102 current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply

c/s. with all internal connections & complete

erected in existing 16 G.M.S.housing

ICS=100% of ICU only Cat III 1.00 Ea. 16221.610

Supplying and erecting triple pole & neutral 440V /

500V panel mounting Copper Busbars with four

103 equal Nos. of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour

insulating tape for phase sequence of following

current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to

each bar, erected in existing cubical panel with

necessary connections.

103.a (A) Suitable for 100 Amp. Capacity 1.00 Rn.Mtr 1961.420

103.b (B) Suitable for 200 Amp. capacity 1.00 Rn.Mtr 3202.710

Providing & erecting weather proof, dust & vermin

proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer

104 body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories

supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments,

earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors, handles

with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice

board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy

powder coating.

(The rates excludes the cost of switchgears, bus

bars, inter connecting mains & Copper Aluminium

strips, meters, Fuses etc. The dimension shall be

measured excluding base beams) The panel shall be

supplied with following approved manufacturers

with following size.

(A) locally fabricated panel board

(i) with 350mm depth 1.00 Sq.Mtr 10468.650

Supplying and erecting approved make suitable

panel indicator lamps of LED type lamp, lens cover,

Bakelite holder complete erected with necessary

Supplying and erecting approved make panel

mounting type Digital Voltmeter having 3 digits LED

106 display, 0 to 750 AC Volts range erected on existing 1.00 Ea. 1275.630

panel board with all connection, wiring etc .with

manufacturers calibration certificate.

Supplying and erecting approved make panel

mounting type Digital Ammeter having 3 digits LED

display, external CT operated, calibrated for 0 to

107 1000 Amps suitable to operate on 500 Volt AC , 1.00 Ea. 1558.430

erected on existing panel board with all connection,

wiring etc .with manufacturers calibration

Supplying and erecting Ammeter / Voltmeter

108 selector switch for 3 phase AC Supply 500 V on 1.00 Ea. 317.140

existing panel board with necessary connections.

Providing & erecting Medium Voltage Danger Notice

109 Board sticker as per language suggested by engineer 1.00 Ea. 26.260

incharge of standard size as per IS-2551

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

110 rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of

MCB to be used) suitable for

(A) single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-43) 1.00 Ea. 1492.780

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia

of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge

111 dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved

make OEM has to submit test certificate) & having

back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test

report must be submitted.

(a) For Electrical Installation up to 440V in normal

soilLength of pipe - 1 MtrBack filling compound - 1 2.00 Ea. 4591.460

Nos Bag of 15 Kg.

Providing and erecting Annealed bare Copper wire

Providing , erecting , fabricating the M.S. structure

as per requirement on site incorporating proper size

of M.S. angles,square,round, flats, bars, channels,

sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide

with erection on site as per direction of engineer in

charge with necessary grouting, cementing,

plastering & finishing complete.

Providing & erecting water cooler having storage

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour

@ an ambient temp of 45˚ C. The outlet temp. of the

water should drop by 15˚C within a hour, The water

cooler should be comprising of hermetically sealed

compressor, fan motor, condensing unit, water tank

surrounded by evaporating, coil, thermostats, relay

etc.complete with necessary inlet & outlet

connection. The body of water cooler will be made

from Stainless Steel.

Supplying & erecting reverse osmosis (RO) water

purification system with M.S. powder coated

pedestal frame, prefilter housing carbon filter

115 suitable buster DC pump, auto low & high pressure

switches with following size of LPH capacity &

erected as directed with one year comprehensive

maintenance guarantee.

[D] 100 LPH with 3 phase Raw water pump of

500LPH @ 2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi),

Dual media filter 10"x54" - (1 No), Micron cartridge

filter 20" x 2.5" ( 1No), High pressure pump 500LPH

@ 10kg/cm2 - (1No - Shimge /CRI /Lubi), RO

Membrane housing with RO membrane of 40*40 -

(1No), RO pressure tube 4" x 1E - ( 1No), 0 - 1200LPH

Rotameter -(2 Nos), with Recovery Rate 50%.

Supplying and erecting Flexible PVC insulated multi

116 strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

e) 1.50 Sq.mm 3 core round PVC sheathed.

Make:Finolex,Polycab,Havell's,KEI,L&T 55.00 Mtr. 46.460

Supplying and erecting approved make Octagonal

pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box

117 consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mmX7.5mm Din-Rail for MCB

Mounting, stud type terminal and arrangement for

cable termination to be erected on foundation as

per details given by manufacturer considering site

(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia,

mm thickness with 200mmX200mmX12mm base

plate, 4-M16 Bolts and 450mm long with necessary

G.I. J Bolts .Approx weight 37 kg

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia,

mm thickness with 200mmX200mmX12mm base

plate, 4-M20 Bolts and 600mm long with necessary

G.I. J Bolts .Approx Pole weight 59 kg

Supplying and erecting Street light pole bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable

for 76.5mm/80mm/require size of pole top having

nuts and bolts for fixing the brackets and having

spread of 0.5 mtr. Length with 110 deg.with vertical

plane and suitable welded stiffener reducer and

nipple with check nut complete painted with one

coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of

[A] Single Arm bracket 0.5 Mtr 5.00 Each 450.460

Providing cement concrete. foundation or for

concrete filling in 1:3:6 ratio with 20 to 25 mm stone

metal duly plastered with necessary curing for pole

muffing or any other purpose.

Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

160 to 270 V,Power Factor more than 0.95, THD <

%, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver

efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection.

(f) Above 60 watts to 90 watts Make-

philips,havells,Schneider, lance, osram

Cat-lll 5.00 Each 5976.170

(C) Post Top Lantern LED fitting comprises of

Copper dust finish cast aluminum spigot and spun

121 aluminum canopy fixed with opal polycarbonate,

pipe arrangement for vertical mounting driver and

accessories wired upto terminal block.IP

(a)20- 30W Make-philips,havells,Schneider, lance,

Cat-lll 5.00 Each 4092.520

(3) LED Bollard fittings of minimum height 1000 mm

& dia.100mm having polycarbonate clear/milky

diffuser mounted on 3mm thick aluminium finished

powder coated pipe with base plate 160x160mm

with erection by M8x75mm fastner with required

RCC foundation.IP65 for 9 to 20 watt and above

,surge-4kv cat-III Make-philips,havells,Schneider,

Providing and erecting HOT deep Galvanised iron

123 strip wire 8 to 16 SWG. 5.00 Each 77.770

Providing and erecting Pipe type earthing having

150 cms.long and 2.5 cms. dia. galvanised iron pipe

with coupling and buch buried in specially prepared

earth pit complete with necessary 8 SWG earth wire.

For using salt and charcoal / coke as required for

125 pipe type earthing. 2.00 Nos. 171.700

providing and erecting Miniature circuit breaker

single pole 0.5A to 2A system and having breaking

126 capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark

Make:Siemens,L&T,Havell's,GE,ABB

Cat.III 10.00 Each 112.110

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium

127 conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(b) 4 core 6 Sq. mm

Make:Finolex,Polycab,Havell's,KEI,L&T

Making trench in Hard Murrum / Tar Road of

suitable width of 90 cm or required depth for laying

128 any size of cable or locating the fault all over the 55.00 Mtr. 74.740

run and back filling the same and making the surface

as normal ground.

Providing & laying approved make Double walled

corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

129 necessary connecting accessories of same material 55.00 Mtr. 62.620

at required depth in existing trench for laying of

cable. below ground / road surface for enclosing

cable Make-Gemini, Dura-gaurd,Rex

(A)50 mm outer dia

Supplying following size of Light duty “A” Class G.I .

Pipe & erecting as directed by Engineer-in-charge.

Supplying & erecting approved make SMC press

moulded composite FRP. loop-in, loop-out approx.

2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob &

hinged doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts

& washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.

( c)150mm x 125mm x 100mm [deep] 5.00 Ea 476.720

Supplying & erecting approved make Digital time

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V +

5%, 16A with, floating contacts Minimum switching

132 setup time 1 minimum & LCD display. Also 1.00 Ea 3168.370

comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover

erected as required with necessary connection

erected as directed.

Supplying & erecting power contactor ,AC3 duty for Ea 857.490

133 time switch complete erected as per direction Cat III

[C] 4 pole 440V 16 Amp.