IMPROVEMENT TO KITCHEN IN CERTAIN MD ACCN IN HAWK ENCLAVE AT AFS BIDAR

Amount

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc., laid bedded and pointed in any mortar complete all as specified and as directed .

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B1 by using 20mm graded stone aggregate as in Slabs supported on walls complete all as specified and as directed.

Mild steel TMT bars 6 to 8mm dia, cut to length, bent to required shape including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips completed all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, and similar work; not exceeding 200m thick (Horizontal or sloping) for fair finished surface complete all as specified and as directed.

Granite (of any type) 18-20 mm thick, work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like including in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite over and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platforms and other similar locations complete all as specified and as directed.

Making hole in granite kitchen cooking platform suitable for gas pipe complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding, removing rubbish off the premisses complete all as specified and as directed.

Glazed coloured ceramic coloured tiles in vertical surfaces 300 X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles as in skirting/dado including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Demolition of brick work, stone / boulder masonry, precast concrete block masonry etc., built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Brick work with sub class 'B' bricks (old size brick) straight or curved on plan to any radius as in half brick thick walls built in cement mortar 1:4 complete all as specified and ascdirected.

Taking down cement plaster on brick or concrete or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed.

Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick in cement mortar 1:3 on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

Preparation of newly plastered wall surfaces and applying 2mm thick wall care putty and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Complete removal of existing treatment of walls including cornices pillars etc and applying 2mm thick wall care putty and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Complete removal of existing treatment of ceilings including cornices pillars etc and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Preparation of old decorated surfaces of walls by washing, rubbing down stopping and applying one coat of oil bound distemper complete all as specified and as directed.

GI tubing 15mm dia medium grade with all fittings and fixed to walls and ceiling or laid in floors including taking down old steel tubing complete all as specified and as directed.

S&F in repairs 15mm bore chromium plated cast copper alloy bib taps fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4sqm each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Powder coated anodised aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions ( Fixed portions) including necessary filling up the gaps at junctions at top, bottom and sides with required EPDM rubber / neoprene gasket etc.,. complete all as specified and as directed.

Powder coated anodised aluminium (minimum thickness of powder coating 50 micron) weighing not less than 0.55 Kg/m for sliding shurtters of doors, windows & ventilators including provision of suitable handle, locking arrangements etc., wherever required including necessary filling up the gaps at junctions at top, bottom and sides with required EPDM rubber / neoprene gasket etc.,. complete all as specified and as directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Pressed steel frames of size 105X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed.

PCC 1:3:6 type C0 by using 12.5 mm graded stone aggregate for filling hollow of chowkats complete all as specified and directed.

Factory made Second class hardwood glazed and skelton door shutters 35mm thick, open rebated and prepared to receive glass, gauze etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass gauze etc , sizes of members of shutters as specified in SSR Part I section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and as directed.

Glazing with sheet glass 4.8 mm thick ordinary quality fixed with oil putty in square n.exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tack or galvanised wire stapples complete all as specified and as directed.

Preparation of new Steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Aluminum anodised barrel tower bolts of extruded section 150mm long complete all as specified and as directed.

Aluminum aodised sliding door bolts of 300mm long with hasp and staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Aluminium anodized handles fabricated type of extruded section of 150mm long complete all as specified and as directed.

S&F 150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed.

Mild steel work as in brackets, hold fasts and other similar items conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

Mild steel work for 'L' or 'T' section supports for shelves etc., and similar articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

Cutting holes into or through concrete/stone masonry/PCC block walling built in cement mortar exceeding half brick and not exceeding one brick and making good in Cement Mortar 1:3 or Cement Concrete 1:2:4, Type B-1 as required for inserting brackets, hold fasts etc and depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall complete all as specified and as directed.

Second class hardwood plain solid straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

M&L for 18/19 mm thick Prelaminated particle board interior grade, both sides prelaminated with decorative choice lamination , fixed with screws to timber frame work for shutters of ward robes, cabinets etc., complete all as specified and as directed.

S & F continuous [piano] hinges, mild steel bright finish and width of flaps 30mm [when open] complete all as specified and as directed.

Teak wood lipping 6mm thick fixed with nails to 18/19mm thick board complete all as specified and as directed.

Magnetic catcher suitable for kitchen cabinet shutters complete all as specified and as directed.

Aluminium anodized handles fabricated type of extruded section of 75mm long complete all as specified and as directed.

Hasp and staple 100mm long, aluminium anodized including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Aluminum anodised barrel tower bolts of extruded section 75mm long complete all as specified and as directed.

S &F in repairs Stainless steel kitchen sink, made of stainless steel 1 mm thick, with plugs, washers, CP waste coupling 38/40mm ( half or full threaded) incluing waste pipe 32mm bore with reducer socket, overall size 495mm X 420mm, bowl size 410mm X 330mm X 160mm complete all as specified and as directed.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or liad on floors including necessary clamps complete all as specified and as directed.

S&F in repairs PVC (SWR) bends 75mm dia with access door any radius complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F in repairs PVC (SWR) bends 75mm dia any radius complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125mm including setting and jointing with solvent cement etc complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (Light, fan, socket or power) complete all as specified and as directed.

Concealed point wiring with 1100V grade 1.5 Sqmm FRLSH single core PVC insulated cable, copper conductor multistranded passing through and including concealed PVC 20mm dia (medium duty) conduit and conduit accessories with concealed 2mm thick galvanised steel pressed sunken box and logic modular white plate of suitable size as required at site with FRLSH PVC insulated unsheathed stranded copper conductor of size 1.5 Sqmm as earth wire connected to common earth dolly including cutting chases in wall and making good disturbed surfaces of walls/ ceiling / floors etc., by using CM 1:3 for one light point / bell point controlled by one switch complete all as specified and as directed.

All as per item No. 59.00 here-in-before but in same board with other switches for 5 Amp switch socket with earth wire 1.5 sq mm PVC insulated multistranded copper conductor FRLSH cable complete all as specified and as directed.

All as per item No. 59.00 here-in-before but for 5 Amp switch socket on independent board complete all as specified and as directed.

All as per item No 59.00 here-in-before but size of FRLSH cable 2.5 sqmm for 15 Amp switch socket with earth wire 2.5 sqmm FRLSH PVC insulated multistranded copper conductor cable complete all as specified and as directed.

Modular switch 1 way 6 Amps 1 module complete all as specified and as directed.

Modular switch 1 way 16 Amps 1 module complete all as specified and as directed.

Modular socket outlet 6 Amps 2/3 pin combined 2 module complete all as specified and as directed.

Modular socket outlet 6/16 Amps 2/3 pin combined 2 module complete all as specified and as directed.

Ceiling rose surfaces bakelite 63.5 X 28mm three terminals complete all as specified and as directed.

Sub main wiring with 2 runs of 4 sqmm, single core, FRLSH PVC insulated, unsheathed, 1100 volts grade, multi stranded with copper conductor, drawn through and including suitable size of rigid non metallic PVC conduit pipe and accessories on surfaces of wall / floor with one run of FRLSH PVC insulated 4 sqmm copper conductor for earth continuity including taking down existing submain wiring complete all as specified and as directed. Note : Three runs of of 4.0 sqmm PVC insulated stranded copper conductor and one run of PVC conduit shall be measured and paid as one unit.

S & F in replacement of MCB DB, SPN 8 way with 200 Amps rated copper bus bar with mild steel sheet enclosure, double door suitable for fixing MCBs and connecting etc., complete all as specified and as directed.

S & F in replacement of MCB SP 6- 32 Amp 240V 50 Hz, 10 KA, 'C' series including making electrical connection with proper size lugs complete all as specified and as directed.

S & F in replacement of MCB SPN 32 Amp 240V 50 Hz, 10 KA, 'C' series including making electrical connection with proper size lugs complete all as specified and as directed.

Taking down carefully existing serviceable Exhaust fan of any sweep and re fixing the same duly grouting with new nut & bolts and provision of new GI louvers including finishing the Exhaust fan opening complete all as specified and as directed.

S & F in replacement of 18/20 W LED Surface mounted, batten fixture, 1200mm in length, with powder coated pressure dia cast aluminium housing and translucent diffuser. The fitting should have multichip on board LED metal clad PCB and dedicated heat shrink. The minimum lumens output of the system should not be less than 1450 lumens. The fitting should have surge protection of minimum 2 Kv input current <200mA, THD<10 % and CCT between 5000 k to 6500 K complete all as specified and as directed.

M/s.Santosh Kotarki