upgradation of Link road NH-44 To madhopur To Shahpurkandi Block sujanpur dissit Pathnakot

Amount

Clearing and Grubbing Road Land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. MORD 2.2

Dismentling of Existing Brick Edging complete in all respect. Including stacking of servicable material and disposal of unservicable material as PWD Specification

Dismantling of flexible pavements and disposal of dismantled materails upto a lead of 100 m & stacking serviceable and unserviceable materials separately as per Technical Specification Clause 202.and & Scarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical Means. MORD 2.14

Excavation for roadway in soil using mech means including cutting and pushing the earth to site of embakement up to a distance of 100 m, including trriming bottom and side slopes in accordance with requirements of lines,grades and X section as per Clause 302 MORD 3.5

Loosening, Levelling and Compacting original ground supporting embankement to facilitate placement of first layer of embankment scarified to a depth of 150 mm mixed with water at OMC and then compacted by rolling so as to achieve, minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specifications Clause 301.4.1 MORD 3.2

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structure graded and compacted to meet requirement of Tables 300.1 & 300.2 as per Technical Specification Clause 301.5. MORD 3.3

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 mtr. Transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with all lead as per MoRD Specification clause 301.5 MORD 3.4

Providing and laying of Brick on end edging 6.83cm wide, 11.11cm long and 22.86cm high half brick deep including excavation, refilling and disposal of surplus earth up to 50mtr complete as per PWD specifications

Laying and consolidation of scarified / dismantled pavement material by adding 20% coarse sand as per specification, carrying the stone metal from stacks, spreaded in uniform layer on prepared surface, mixing in place with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD specification clause 401. MORD 4.1

Granular Sub Base (Grading-I) - Construction of granular sub base by providing well graded material (Grade-I), spreaded in uniform layers on prepared surface, mixing in place with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD specification clause 401.MORD 4.1

Water Bound Macadam (Grading - II) - Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening type-A/ binding materials to fill-up the interstices of coarse aggregate, watering and compacting to therequired density grading 1 as per MoRD Specification Clause 405. MORD 4.7 ii

Water Bound Macadam (Grading - III) -Providing, laying, spreading and compacting stone aggregates wbm GR-II) of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening type-B to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per MoRD Specification Clause 405. MORD 4.7 iii

Primer Coat - Providing and applying primer coat with Bitumen Emulsion (Slow Setting-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate 0.85 kg/sqm using mechanical means as per MoRD specification clause 502 MORD 5.1 i

Tack Coat - Providing and applying tack coat with Bitumen VG-10 using tar boiler / pressure distributor at the rate of 0.275 kg. per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per MoRD specification clause 503 MORD 5.2 ii

Bituminous macadam -Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous inder VG-10 @ 3.4% transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504. MORD 5.3

Providing, laying and rolling of close- graded premix surfacing (Mix Seal Surface) material of 25mm thickness composed of 13.2mm to 0.9mm (Type - B) aggregates using penetration grade using bitumen VG-10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8 - 10 KN static rollar and finishing to required level and grades as per Technical Specification Clause 507. MORD 5.11 A (II)5-37

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.

Credit of Bricks (3rd Class) received after dismentling

Credit of Brick bats received after dismentling

Providing & erecting "W" type metal beam crash barrier single sided comprising of 3mm thick corrugated sheet metal beam rail 70cm above road or ground level fixed on channel vertical post 150x75x5mm spaced 2mtr centre to centre 1.80mtr high, 1.1mtr below road or ground level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 & IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150x75x5mm, 330mm long fixed firmly into ground with vertical hydraulic self driving machine for vertical post complete as per approved drawings and technical clause IRC: 119-2015.

Providing and laying 80 mm thick factory made cement concrete interlocking Paving blocks of M40 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-inCharge. MORD 6.7

Earth work in excavation for foundation of structures upto 3 m depth as per drawing and tech. specifications clause 1104 including setting out, const. of shouring and bracing, removal of stumps and other deleterious matter,dressing of sides and bottom and backfilling with approved material MORD 9.1

Providing Plain Cement Concrete 1:3:6 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. MORD 11.4

Providing and laying reinforced cement concrete pipe NP3 450 mm dia for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. MORD 9.7

Providing Coursed Rubble masonry Stone masonry in cement mortar 1:4 for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing Coursed Rubble masonry Stone masonry in cement mortar 1:5 for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204. MORD 12.4

Raised Pointing with cement mortar (1:2) on Stone wall in substructure as per CSR 15.64

Providing Cement Concrete (Plain / Reinforced) P.C.C. grade M 20 in Sub Structure complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. MORD 11.4 III

Back Filling Behind abutment wing wali and returnwall complete asper drawings & technical specification clause 1204.3.8 MORD 12.10

Painting two coats New Concrete surface including prime coat after filling the suface with surface with synthetic enamel paint in all shades on new plastered/concrete surfaces asper drawing and technical Specification clause 1701 MORD 10.5

Providing Cement Concrete (Plain / Reinforced) M-20 in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing and laying reinforced cement concrete R.C.C M 25 in Sub Structure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5

Providing and laying reinforced cement concrete R.C.C M 25 in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 MORD 12.5 VI

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701.

Providing weephole in brick masonry / stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia PVC pipe extending through the full width of the structures with slop of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614,709,1204.3.7 MORD 12.9

Supplying of fine sand and backfilling as filter media along HMP, behind head walls, wing walls complete as per drawings and technical specifications clause 1204.3.8 MORD 12.10

Plastering with Cement Mortar (1:4), 15 mm thick on brick work in sub structure as per technical specification Clause 613.3 & 1204 MORD 9.13

Supplying cutting fitting and placing TMT (Fe500/550) reinforcement bars in sub structure complete as per drawing and technical specification caluse 1002,1010 & 1202. MORD 12.7

Supplying cutting fitting and placing TMT (Fe500/550) reinforcement bars in super structure complete as per drawing and technical specification caluse 1002,1010 & 1202. MORD 13.3

Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans, covered with sealant complete as per drawing and technical specifications MORD 13.16 ii

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301 MORD 14.2

Reinforced Cement Concrete M15 grade 5th kilometre stone of standard design as per IRC: & fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 MORD 10.10

Reinforced Cement Concrete M15 grade ordinary kilometre stone (precast) of standard design as per IRC : & fixing in position including painting and printing, etc. as per drawing and MoRD Specification Clause 1703. MORD 10.10

Reinforced Cement Concrete M15 grade 200 metre stone (precast) stone of standard design as per IRC : & fixing in position including painting and printing, etc. as per drawing and MoRD Specification Clause 1703. MORD 10.10

Supply & Fixing of 250 mm dia NP Type-II pipe Boundary Pillar complete as per drawing & technical specification clause 1704

Providing and fixing of typical PMGSY Logo sign board (Double Sided) as per MORD specifications and drawing. MS Plates of 1.6 mm thick duly welded on MS angle iron frame of 25mm x 25mm x 3mm. The angle iron frame welded to 1 no. MS square tubes post 75mm x 4.9mm thick duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. The top diamond plates (600 mm) and definition / arrow plate (1100mm x 300mm) will be welded to MS post. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. MORD 10.16

Providing and fixing of typical PMGSY Logo & Informatory sign board as per MORD specifications and drawing with ACP Sheet 3mm & 4mm thick fixed on MS angle 25mmx25mm x 3mm size on back on edges. Vertical Post MS square tubes 80x80x4.80mm thick duly embedded in cement concrete M-15 grade blocks of Size 450mm x 450mm x 600mm, below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing comp. in all respects. MORD 10.16

Providing and fixing of PMGSY Citizen Informatory board as per MORD specifications and drawing with ACP Sheet 4mm thick fixed on MS angle 25mmx25mm x 3mm size on back on edges. Vertical Post MS square tubes 80x80x4.80mm thick duly embedded with base plate 300x300x5mm in cement concrete M-20 grade blocks of Size 600mm x 600mm x 750mm, below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing comp. in all respects. MORD 10.16

Providing and fixing of typical PMGSY Maintenance sign board as per MORD specifications and drawing. MS Plates 1.6 mm thick duly welded with MS angle 25mmx25mm x 3mm size on back on edges. The plates welded with MS flat of 50mm x 5mm. The flat iron frame of plates welded to 2 nos. MS square tubes posts 75mm x 4.9mm thick duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm, 750mm below ground level. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 MORD 10.16

Providing and fixing of Retro-reflective Cautionary, Mandatory and Informatory Sign Boards as per IRC : 67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over Aluminium sheeting supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450mm x 600 mm, 600mm below ground level as per drawings and MoRD Specification Clause 801 MORD 10.2

600mm equilateral triangle

600 mm side Circular

600x400mm rectangular

600x600mm rectangular direction & identification sign board

800x600mm rectangular direction & identification sign board

Hazard Marker Sign Board 300x900mm Rectangular

600x900mm rectangular direction & identification sign board

Providing and fixing Standard Chevron Sign Board size 500x600 mm (Double sided)

Supply Installation & Fixing of Convex Mirror

Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications. CSR 24.57

Providing and making rumble strips 15-20mm high at centre, 250mm wide placed at 1m centre to centre over freshly laid bituminous layer by using close graded premix surfacing material type B at approved locations to control speed and marked with 100mm wide white strips of thermoplastic road marking paint. The close graded premix surfacing material type B shall conform to technical clause 512 and thermoplastic road marking paint shall conform to technical clause 803 of MORT&H specifications

Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflectivepanels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications. CSR 24.63

Routine Maintenance after completion of construction work as per periodicity of Routine Maintenance mentioned in the contract data.

For 1st year

For 2nd year

For 3rd year

For 4th year

For 5th year

RAJESH WADHERA GOVT. CONTRACTOR

Ms R.K. Mahajan

V S Saini Contractor